Search Documents

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle' and in particular for the special case under consideration.1'2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43', 55° 16', 64 3 43 1, and32"26'. These add up to 1802 08 1, indicating a cumulative error of 8'. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43', 55°16'), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.' Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

By R. S. Cartwright

Two types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control. of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent upon the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination-the combination which when engaged will suspend the least amount of weight-has a value of 1.00.

Jan 1, 1928

Jan 1, 1961

By Sherwin F. Kelly

The Geophysics Education Committee was organized in 1938 and presented its first report at the A.I.M.E. annual meeting in February, 1939, at a session held jointly with the Committee on Geophysical Methods of Exploration. REPORT OF 1939 The first task the Committee set itself was to find out in which universities the subject of geophysics was being taught, and the manner in which such instruction was given. A questionnaire was drawn up and sent out to 147 universities in the United States, Canada, and abroad. Of these 100 replied. Their answers were then tabulated and analyzed, yielding the information summarized in the following pages. Two universities, Colorado School of Mines and St. Louis University, actually maintain departments of geophysics, while 3 Canadian and 31 American universities give courses on the subject. In other institutions, 45 in the United States and 5 in Canada, more or less extended reference is made to geophysics in lectures on other subjects. Altogether, there are at least 86 universities in the United States and Canada at which students may obtain instruction of some kind in geophysics. To enter the courses in geophysics given by 33 American universities, certain prerequisites are demanded, varying with the level at which the subject matter is treated. In analyzing the prerequisites, some assumptions had to be made: one year of college mathematics was taken to mean up to, but not including, calculus, while three years was presumed to embrace a course in differential equations. On this basis, 16 per cent require only elementary college mathematics, 40 per cent require differential and integral calculus, and 31 per cent require differential equations. A few demand even more advanced mathematics, while some list no prerequisite mathematics beyond high school. Evidently a student contemplating the study of geophysics should ground himself in calculus and differential equations. In physics, similar assumptions have been made as to time required in the subject. All of the universities giving geophysics require their students to take physics first, and 34 per cent require a standing in

Jan 1, 1940

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By R. B. Muter, W. C. Grady, T. D. Wheelock, D. G. Chedgy

INTRODUCTION Topics of special interest, such as preparation plant flowsheets and noise pollution, are described in this chapter along with a discussion of non- state-of-the-art processes such as chemical cleaning, high intensity magnetic separation, and bacterial oxidation. PREPARATION PLANT FLOWSHEETS by RICHARD B. Muter In determining the layout or combination of unit operations to be utilized in a modern preparation plant several factors must be taken into account.

Jan 1, 1979

By Sherwin F. Kelly

The Geophysics Education Committee was organized in 1938 and presented its first report at the A.I.M.E. annual meeting in February, 1939, at a session held jointly with the Committee on Geophysical Methods of Exploration. REPORT OF 1939 The first task the Committee set itself was to find out in which universities the subject of geophysics was being taught, and the manner in which such instruction was given. A questionnaire was drawn up and sent out to 147 universities in the United States, Canada, and abroad. Of these 100 replied. Their answers were then tabulated and analyzed, yielding the information summarized in the following pages. Two universities, Colorado School of Mines and St. Louis University, actually maintain departments of geophysics, while 3 Canadian and 31 American universities give courses on the subject. In other institutions, 45 in the United States and 5 in Canada, more or less extended reference is made to geophysics in lectures on other subjects. Altogether, there are at least 86 universities in the United States and Canada at which students may obtain instruction of some kind in geophysics. To enter the courses in geophysics given by 33 American universities, certain prerequisites are demanded, varying with the level at which the subject matter is treated. In analyzing the prerequisites, some assumptions had to be made: one year of college mathematics was taken to mean up to, but not including, calculus, while three years was presumed to embrace a course in differential equations. On this basis, 16 per cent require only elementary college mathematics, 40 per cent require differential and integral calculus, and 31 per cent require differential equations. A few demand even more advanced mathematics, while some list no prerequisite mathematics beyond high school. Evidently a student contemplating the study of geophysics should ground himself in calculus and differential equations. In physics, similar assumptions have been made as to time required in the subject. All of the universities giving geophysics require their students to take physics first, and 34 per cent require a standing in

Jan 1, 1940

By A. L. Holley

The application of scientific methods to the investigation of natural laws and to the conduct of the useful arts which are founded upon them, is year by year mitigating the asperity and enlarging the outcome of human endeavor. More notably, perhaps, are these the facts in that system of productive and constructive arts of which engineering is the general name. In metallurgical engineering especially, within the period of our own recollection, how rapid has been the rate and how wide the scope of progress: the scientific discovery and mining of metalliferous veins; the economical separation and reduction of ores of every grade; the production and regulation of high temperatures; the varied improvements in the manufacture of iron, in saved heat and work, in uniformity and range of products; and, most important of all, the creation and the utilization, to be counted by the million tons a year, of the cheap constructive steels. Wonderful as this range and degree of development may appear to the public eye, the close and thoughtful observer must, nevertheless, conclude that neither the profession nor the craft of engineering may congratulate themselves too complaisantly, but that they should rather acknowledge to each other the embarrassing incompleteness of the union between engineering science and art. There is a small school of philosophers whom we may designate as original investigators, men who come close to nature, who search into first principles, and who follow that scientific and therefore fruitful method by which the relations of matter and force are discovered, classified, and brought within the reach of practice. These wonderful men do not indeed create the laws of nature, as they sometimes almost seem to, but they go up into the trembling mountain and the thick darkness and bring down the tables upon which they are written.

By P. D. Merica, H. Scott, R. G. Waltenberg

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903—1911 by A. Wilm1,2 and have been described by him and by others. 3, 4,5.6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from tempera-

Jan 1, 1921

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By C. R. Van Hise

Introduction.............29 The Three Zones of the Lithosphere ..30 Zone of fracture............31 Zone of flowage............ 31 Factors influencing depth at which flowage occurs.. 32 Zone of combined fracture and flowage.. 33 The Water-Content and Openings in Rocks....36 Condition of rater in the zone of fracture.. 36 The openings in rocks...........38 Size and number of openings..... 40 Ore-deposits derived from zone of fracture..45 The source of underground water......... . 47 The cause of the flowage of underground water..47 Belts of underground circulation.. 51 Upper belt of underground circulation.. 51 Lower belt of underground circulation.. .... .52 Capacity of water for work in the lower belt of underground circulation........... 53 Movementsof water in the lower belt of underground circulation. 54 The preferential use by water of large channels.. 60 Physico-Chemical Principles Controlling the Work of Under ground Waters..........62 Chemical action............63 Underground aqueous solutions..64 The relations of solution and temperature..... 65 The relations of solution and pressure..66 Precipitation........... 67 Precipitation by change in temperature..68 Precipitation by change in pressure..69 Precipitation by reactions between aqueous solutions.. . 69 Precipitation by reactions between liquid solutions and solids. 70 Precipitation by reactions between gases and solutions. and solids............71 The General Geological work of Underground Waters.. . 71 Division of the zone of fracture into a belt of weathering and a belt of cementation............72

Jan 1, 1901

By AIME AIME

AT A meeting of the Iron and Steel Institute held in London on May 6, Dr. J. E. Stead was formally inducted into the chair by Dr. Eugene Schneider, the retiring president. After presenting the Bessemer gold medal to Harry Brearley, of Sheffield, England, for his distinguished services to the British steel industry, Doctor Stead delivered his presidential address, a masterly review of iron and steel making progress during the past 50 years, emphasizing economy in production, and pointing out suggestions for future improvement. A considerable portion of the address was devoted to blast-furnace operation.

Jan 1, 1920

By Jacques B. Wertz

Detailed structural studies in southeast Arizona have successively revealed (1) the local attitudes of individual fractures (with lateral and/or vertical displacements), (2) the patterns exhibited by groups of fractures, and (3) the trends and directions shown by fracture groups or zones on a regional scale. The results of the studies have been twofold: First, domes were locally determined from these fracture arrangements, even where other criteria failed; and, second, fundamental breaks brought out the breadth of the Texas lineament in southeast Arizona as well as major northwest- and northeast-trending fracture zones. Coincidence of one or several domes with the major intersections of fundamental breaks can be centers of important mineralization, as in the instances of Bisbee, Ajo and Morenci. THE OVER-ALL STRUCTURE OF ARIZONA A northwest-southeast trending anticlinorium has been suggested as the structural setting of Arizona. Starting in Triassic and culminating in late Cretaceous times, this deformation resulted from stresses of considerable magnitude with varying ratios of com pres sional and uplifting forces. However, the series of parallel flexures could just as well have been caused by isostatic movements involving dilation under tension with only incidental compression, as later emphasized by dike filling and block faulting (Fig. 1). The anticlinorial deformation, which is also suggested by the fact that the Pre-cambrian rocks to the southwest are all concealed by sediments, could be somewhat reminiscent of the conditions that affected the classical swarm of parallel dikes of wager.' ANALYSlS OF DATA As a first step in this analysis, all structural information obtained on such features as fractures and their relative displacements, faults, dikes, anticlines, synclines, and Precambrian and Laramide-Tertiary intrusives were plotted on maps along with structural trends inferred from aerial photographic mosaics. Next, the faults in southwest Arizona were classified according to time of occurrence and relative importance. The fault assemblages were then examined as to geometric or spatial arrangement and correlated with the occurrences of domes and existing Finally, the conjunction of fracture intersections and domes was analyzed and compared with locations of known ore deposits. Differentiation of Faults According to Time and Relative Importance: The faults encountered were grouped as follows: (1) Basin and Range faults, latest in time; (2) secondary faults; (3) primary faults; and (4) lineaments, earliest in time by inference. BASIN AND RANGE FAULTS- Generally concealed by alluvium, the Basin and Range faults are normal

Jan 1, 1969

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company's lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company's nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954

By W. F. Domis, F. von Gemmingen, F. Garofalo

The effect of rain size on the creep behavior of an austenitic iron-base alloy has been studied at 1300° F under conditions of constant stress. The average grain diameter varied between 9 and 190 p (ASTM 10.7-2). The subgrain size and apparent activation energy for creep were not found to depend in any systematic manner on gain size. Grain hozmdary serrations were observed in all specimens tested. The variation of the secondary-creep rate, 2,, with the pain diameter, 1, is given by: es = K(213m + 1 )/l.]; 1, is the grain diameter zohere is reaches a minimum. Results in the literature shoujthat 1,increases as the temperature increases. At low creep temperatures is is therefore proportional to 12, at intermediate temperatures <, exhibits a minimum, and at high creep temperatures is is proportional to 1/1. The dependence ofis on the stress, u, is given by: t, = A" (sinh acrln, a and n show little variation with 1. The dependence of A" on 1 is given by: A" = KA[(21k + 13)/1]. For 1 » >>lmn = 4, and at constant values 01- isat lozu stress levels, the steady-state stress is given by the Hall-Petch relation. The variation of c, with grain size is believed to he associated particularly with grain boundary generation of dislocations which becomes more important with increasing temperatures. SEEMINGLY inconsistent experimental findings have led to a certain amount of confusion concerning the effect of grain size on creep behavior. The confusion is attributed to a lack of test results obtained over sufficiently wide ranges in grain size, stress, and temperature. Experimental results presented in this paper and results available in the literature1-5 show a consistent behavior and lead to a unified concept for the dependence of secondary-or steady-state creep rate on grain size. In accordance with this concept, which is substantiated experimentally, secondary-creep rate should increase with increasing grain diameter at low creep temperatures, leading to greater creep strengths for fine-grained materials. At intermediate temperatures the secondary-creep rate should decrease to a minimum and then increase as the grain size is increased. At high creep temperatures the secondary-creep rate should decrease with increasing grain size, leading to greater creep strengths for coarse-grained materials. Whether a temperature is high or low for creep in a metal or alloy depends primarily on its melting temperature. MATERIAL AND TEST PROCEDURES The material tested was an austenitic iron-base alloy of the following composition (wt pct): C, 0.005; N, 0.017; Mn, 1.26; Ni, 14.21; and Cr, 17.18. Two 15 -lb ingots were forged and hot-rolled to 5/8-in.-diam bars which were then cold-rolled and cold-swaged to a diameter of 0.49 in. These were sectioned into 3-in.-long blanks and heat-treated at various temperatures to obtain different grain sizes. The procedures employed and the results obtained are summarized in Table I. The secondary treatment at 1400° F followed the primary treatment without intermediate cooling to room temperature. This final treatment was employed to minimize various effects arising from heating to different temperatures during the primary treatment, particularly differences in intragranular dislocation structure, segregation of interstitial atoms at grain boundaries, and density of grain boundary ledges. The intragranular dislocation structure was examined by electron transmission metallography after each of the treatments described in Table I. Isolated dislocations and a few tangles were observed but no evidence of subgrains was found after any of the treatments. No grain-size effect was evident on the density and distribution of dislocations. Stabilization of grain boundary structure is particularly important because, as will be discussed later, grain boundaries influence high-temperature creep behavior. Magnetic-permeability measurements after each treatment and

Jan 1, 1964

By Carl Zapffe

THE object of the Bradley process is to free manganese oxide from its associated gangue and separate the contained iron oxide by dissolving the manganese and precipitating it from the solution. &apos;The fundamental features of the process are : making. both 1 a manganese ore and an iron ore; effecting a separation of manganese .and. iron by means of selective roasting; leaching- the manganese from the roasted ore by using &apos; ammonium sulfate; precipitating the manganese by using the ammonia gas generated during leaching; fixing the precipitate by oxidizing with air; breaking down and reforming the ammonium sulfate, so that daily very little additional ammonium sulfate beyond that originally charged into the system is required; washing the manganese precipitate and the iron-silica residue and evaporating the liquor to conserve the dissolved salts in the moistures of these two products and &apos;to reduce the sulfur content,; drying the precipitates; magnetic wet-concentration of the iron-silica residue; sinteriny the manganese-and .the&apos; iron-concentrates.

Jan 1, 1929

By Robert F. Mehl

THIS essay is an attempt to present the elementary facts and ideas concerning the growth of crystals, especially of metals. Freezing, like all heterogeneous processes, is a process of nucleation and growth; it manifests itself in metallurgy primarily in the freezing of ingots. The preceding paper in this volume discusses nucleation; the paper to follow describes ingot solidification. The present paper will treat of the growth of nuclei to large crystals, embracing a long series of phenomena, many of which are familiar to metallurgists.† Crystal growth, it will be immediately noted, occurs not only in the freezing of metals, but in the freezing of all substances; and it is a prominent and familiar phenomenon in crystallization from solutions, aqueous or otherwise, and in crystallization from the vapor phase. It will be necessary to include such systems in this discussion, for so much of value to metallurgists has been learned from their study. Apart from this, so far as metals are concerned, it will be simpler to limit the discussion to the freezing of pure metals and of solid solutions. Other types of freezing-eutectic, peritectic, etc.-will be excluded, though they have much of interest and of importance. BASIC MECHANISM OF FREEZING Ideally, nucleation and growth processes can best be considered from the point of view of isothermal reaction and upon the assumption of random nucleation. In. such an ideal case, nuclei form at random, and at a characteristic rate either constant or changing with time, and grow to spherulites at a characteristic rate, constant or changing with time, Fig. I.. On the simplest assumption, the reaction rate-in this case the rate of freezing-is a resultant of these two component rates. The reaction rate equation may be written in terms of these two component rates. The formation of pearlite from austenite closely approaches this ideal case. The ideal case forms a very useful point of departure in considering real cases. Various factors of reality produce deviations from this assumed ideality. In freezing, the isotropic medium, the melt, passes to the anisotropic solid, the crystal. Crystals are lattices of atoms, and the unit cell is often referred to as a crystal unit. Rosenhain, many years ago, represented the nucleation and growth process on freezing in the manner shown in Fig. 2, feeling, intuitively, that there must be some crystal unit in crystal growth. It now appears that this may be true, though his picture requires much elaboration. The greatest deviation from ideality lies in the nonisothermal nature of the freezing process in metals. To approach this properly it should be recalled that many nonmetallic substances freeze slowly. Tammann, to whom we owe the classic approach, studied complex organic materials in which (as in the case of eutectoid steels at high

Jan 1, 1951