Search Documents

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By G. H. Wilson

INTRODUCED in 1946 to serve a need in power- plant operation, closed-circuit TV has been used by well over 200 organizations in approximately 25 different industries. Known as industrial television, or simply ITV, it can be described as a private system wherein the television signal is restricted in distribution, usually by confinement within co-axial cable that directly connects the TV camera to one or several monitors, Figs. 1, 2. The picture is continuous and transmission is instantaneous, permit- ting an observer to see an operation that may be too distant, too inaccessible, or too dangerous to be viewed directly. Destructive testing or the machining of high explosives can now be conducted hundreds of feet away by personnel who still have close control through the eyes of the TV camera. It is also possible for one man to control operations formerly requiring the co-ordinated efforts of several workers. For example, at a large midwestern cement plant conveyance of limestone from primary crusher to raw mill and loading into five storage bins once necessitated the work of two men, one having little to do but prevent spilling of material by manually moving the tripper on the belt conveyor as occasion required. TV cameras mounted on the tripper now provide bin level indication to the conveyor operator at the crusher position so he is able to control the entire loading operation remotely, Fig. 3. By means of a switch, the picture from either camera is alternately available on a single viewer, or monitor, Fig. 4. Each camera is mounted on the tripper by means of a simple adjustable support and looks down into the bin, which is identified by the number of cross members on the vertical rod. Each associated power unit is located on a platform above the camera, Fig. 5. This centralized control by means of TV often has produced superior results, and in many instancés saving in operating costs has been sufficient to write off equipment costs within six months to a year.

Jan 7, 1954

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By E. A. Anderson

In another paper' the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 Ib. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging. Experimental Work Two methods of increasing the maximum permissible fiber stress in zinc were considered. Cold rolling, which' increases the stiffness and tensile strength, was found to decrease the resistance to slow flow. Alloying, therefore, provided the only feasible means of obtaining the desired result, It was recognized that the improvement secured by the solid solution of natural impurities was insufficient. A series of alloys was outlined, therefore, in which a number of metals were added separately and together. The sheets rolled from these alloys were tested under

Jan 1, 1930

George IV. Goetz, Milwaukee, Wis.: Mr. Campbell deserves much credit for his interesting paper. The literature of the development of the open-hearth process is distributed in many technical journals, and is difficult of access to many engineers. Since the development of the basic process, the open-hearth furnace has been raised from a subsidiary to an independent position. Certain high grades of soft steel can be produced in the basic open-hearth furnace, which cannot be produced by any other known process. In the United States the charges for the acid process generally consist of either scrap and pig-iron or so-called wash-metal and scrap : the pig-and-ore process, as carried out in England, is practiced but very little. The introduction of the basic process has made it possible to use about four times as much pig-iron with scrap as can be used in the acid mixtures. The availability of a cheap pig-iron, very low in silicon and sulphur, and carrying several per cent. of manganese, is one of the reasons why the basic open-hearth process has developed so rapidly in Germany, as regards the output per furnace and the excellent quality of the material produced. The acid Bessemer steel has an inherent stiffness, which is plainly shown when spring steel is made by the Bessemer and by the openhearth processes. In order to get them of about equal stiffness, the open-hearth steel must have about 0.60 per cent. carbon ; whereas, the Bessemer steel must then have ahout 0.45 carbon, the remaining constituents being apparently about the same in each product. It has proved impracticable, with American coke-pig-iron, to interrupt blowing at a certain point in order to make hard steel; and experience has therefore shown that it is best to eliminate nearly all the carbon, and then to recarburize to the desired point. This practice

Jan 1, 1894

By R. G. Hall

An article on the subject of electrolytic zinc no longer needs to be preceded by an apology. The production of zinc by electrolysis is past the laboratory stage and has become an economic factor of considerable importance in the total production of zinc in the United States. The various methods of procedure to be followed fa the greatest economy of manufacture are fairly well known, consequently a detailed description of any method is no longer necessary or desirable. In this paper I shall endeavor to lay down some of the governing conditions in this industry, the relation of methods to ore deposits, freight rates, and sources of power supply. Power Points Assuming for a moment that, for the present at least, the electrolytic production of zinc will be confined to Those localities having developed water power, a glance at these powers so developed in the United States, with their relation to known zinc orebodies of economic size, will not be without interest. Northwest In the Northwest we have water powers, developed and undeveloped, . in Washington and Montana. These must, of course, bear a close relation to the rapidly growing zinc production of the Coeur d'Alenes and of the Butte districts. In general, the power of the territory in question is relatively low-priced, at least as compared with the cost of developing power from coal, and the near neighborhood of large bodies of more or less complex zinc ores makes these water powers of more than usual interest. The same remarks may be applied equally to the developed water powers of the Canadian side of the line in the Northwest, where we have again commercially available complex ore deposits such as are being exploited today at and near Trail. California One of the large complex ore deposits of the far West is to be found in Shasta County in the immediate neighborhood of the territory of the

Jan 1, 1918

By Charles Colcock Jones

In any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly not due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul. "Ore Supply Edwin C. Eckel, in his monumental work on Iron Ores, has but little to say concerning the Pacific Coast deposits. He mentions (p. 269) those of Minaret, Madera County, and the Eagle Mountains, Riverside County, Cal., "perhaps 50 to 100 million tons each;" the deposits in Shasta County, worked for the electric furnace on Pitt River; and

Jan 1, 1916

By William E. Brewster

Dating back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus content, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/6-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a 1/2 factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

THAT the march of civilization has synchronized with progress in the art of utilizing minerals is a proposition that needs no proof. It is a truism. Historians conveniently divide the time that the earth has been inhabited into the Stone Age, the Bronze (more accurately the Copper) Age, and the Iron Age. As archeologists are not entirely in accord as to dates, and as a few centuries make no difference whatever to this particular story, it may be approximated that the Age of Copper began about 8000 years B.C. and that it gave place to the Age of Iron about 1000 years B.C. The logic of this succession-stone, copper, iron-lies in the fact that copper first displaced stone, then iron displaced copper as the standard material out of which the utensils, implements, and weapons, the utilitarian articles of antiquity, were made. After the advent of iron, the mining and smelting of copper continued. Copper and bronze found use particularly in objects of artistic and ornamental nature; but the superior qualities of iron for many purposes were recognized. Useful manufactures of those days consisted principally of knives, hammers, chisels, spear-heads, arrow-heads, and battle-axes. First these were made of stone, then of copper and bronze, then of iron-particularly as there was plenty of iron ore, and the metallurgy was comparatively easy of accomplishment. Of course, the periods of transition dragged slowly. Definite as were the three Ages dominated by the mineral substance from which they get their names, ten or fifteen centuries probably elapsed from the time the first iron was smelted in a small charcoal furnace until it became the accepted material from which to shape a battle-axe. Contrast this with the pace of modern progress. In a brief span, half a dozen more or less deserving candidates for the distinction of having their name

Jan 1, 1933

By William Newnam

WHEN Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great anti the tonnage was small, but on the other hand the results were fairly, satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Roan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process.. The Luce and Rozan process has persisted in its original form to the present clay. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process.

Jan 5, 1917

By W. C. Hardy, B. W. McArthur

The purpose of this work is to show application of laboratory data in calculating solution gas-drive performance of the Cisco K-I reservoir. Included herein is a diagram showing the graphical relationship between six variables common to all solution gas-drive mechanisms. With an iterative process one may assume existence of any of these six variables at a particular pressure and calculate the production performance likely to occur in a reservoir produced by solution gas drive. Four unique pressure values are described at which the material balance equation alone is sufficient to predict the cumulative volumes of gas produced. Information derived from these pressure points establishes a criterion for determining compatibility of the pressure-volume-temperature (PVT) analysis of the produced crude with the gas production history. Two averaging procedures are used to arrive at a relative permeability-saturation relationship which describes the field-wide performance. INTRODUCTION The Cisco K-1 reservoir is a lenticular-type sand structure lying at approximately 6,300-ft subsurface. It is located in the H. and T. C. Railroad Co. Block 97, SW 1/4 S 392 and NW 1/4 S 385, Scurry County, Tex. Correlation of data from logs indicated that the Cisco K-1 reservoir occupied approximately 3,218 acre-ft of space with a closure of from 15 to 20 ft. Analysis of the production data indicates that the initial formation pressure and temperature were 2,450 psig and 121°F, respectively. The bubble point occurred at 1,715 psig after production of 12,256 STB oil and 11,520 Mcf gas. Only traces of water have been produced since initiation of production. Successive material balance calculations from June, 1952, to June, 1957, showed that no initial gas cap or water influx has contributed to production of oil and that the Cisco K-1 reservoir originally contained approximately 1.44 X 10" STB of oil. THEORY Methods for calculating solution gas-drive perform-

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe's interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By Robert V. Whitman

INTRODUCTION Ideally, this paper should start by citing examples of slope failures in open pit mines during earthquakes. I do not know of any such examples, although - since my search of the literature has not been exhaustive - such examples may well exist. However, there certainly are many examples of devastating earthquake-induced landslides, and there is no reason why such landslides cannot occur at large open pits. Moreover, many of the actual earthquake-induced landslides have seriously affected mining operations in one way or another. Hence, this paper will treat earthquake-induced landslide phenomena in general, in the hope and expectation that the reader can apply this general knowledge to the specific problems associated with open pit mining. Ultimately, of course, the aim is to predict the likelihood of the occurrence of earthquake-induced landslides, and to delineate steps which can be taken to minimize the possibility of their occurrence. These aims can be achieved only imperfectly at the present time, for our knowledge concerning earthquake-induced landslides is still in an embryonic stage. Nonetheless, much useful knowledge does exist. In order to understand and apply this knowledge, it is necessary to: 1. Review the nature and extent of actual earthquake-induced landslides; 2. Have a grasp of the basic terminology and concepts of seismology; 3. Study the fundamentals of probability-based seismic risk analysis; 4. Appreciate the way in which earth materials behave during earthquake loadings; and 5. Have a general knowledge of the methods currently available for analyzing the dynamic response of slopes. Much of this paper is devoted to this necessary background. Information of practical use in connection with various classes of slope stability problems is assembled in the final sections. LANDSLIDES DURING PAST EARTHQUAKES Almost every earthquake in mountainous country, strong enough to be reported in the literature, has caused at least some landslides and rockfalls. Unless these slides or falls damage

Jan 1, 1971

By J. Campbell

The negative pressure developed within a solidifying sphere of pure iron is investigated theoretically assuming an elastic-plastic model. The maximum hydrostatic tension attainable is shown to be an order of magnitude smaller than that required for the homogeneous muclealion of pores in the liquid cove, and four orders of magnilude smaller than that predicted from) a rigid shell model. It is well-known that liquids can withstand large hydrostatic tensile stresses, or negative pressures. The various experimental investigations of the tensile strengths (often called the fracture pressures) of liquids are reviewed by Dean,1 and the theoretical attempts at estimating fracture pressures are critically assessed by wakeshima.2 Using Fisher's3 quation, the fracture pressure of pure liquid iron is about -70,000 atm, which may be too large by as much as a factor of 4, but is certainly correct to within an order of magnitude.' In view of the great importance of the problem of the nucleation of shrinkage cavities in castings it is of interest to determine exactly what tensile stresses can exist in the residual liquid in a solidifying casting; it has often been assumed that, because of the very low strengths of solid metals near their melting points, no interior stresses are developed at all. Nussey4 has determined theoretically the pressure in the liquid core of a solidifying metal sphere assuming that the solidified shell does not deform (i .e., is perfectly rigid), so that because of the contraction accompanying solidification (a) (about 3 pct for most metals) the progressive deposition of solid onto the inner surface of the shell causes the remaining liquid to be expanded to make up this difference in volume. This leads to a relation between the pressure P in the liquid, the initial pressure, PO, the bulk modulus of the liquid, K, and the inner and outer radii of the solid shell, o and b, respectively:

Jan 1, 1968

By Hans Conrad, W. D. Robertson

FORMAL theories of yielding and flow have been developed to describe thermally activated plastic flow in metal crystals.'-" hey are all based on Becker's' original idea that thermal fluctuations aid the applied stress in overcoming internal barriers to flow and lead to the following relation. where j is the strain rate; C is a constant which includes a frequency factor, the entropy, the number of flow units, and the amount of strain associated with each successful fluctuation; E(T) is the activation energy associated with flow, and is a decreasing function of the applied stress, 7; k is Boltzmann's constant; and T is the temperature in OK. The various theories differ mainly in the model chosen and in the nature of the relationship between the applied stress and the activation energy. Beckerl and Orowan' suggest a relationship of the form E a(Ti — t)2, where .ri represents the stress required for flow without the aid of thermal fluctuations; Kauzmann,3 Cottrel1,5 and Seeger6,7 suggest E a(t — t) ; Fisher8 suggests E while Cottrell and Bilby4 suggest a more complex relationship between E and 7. Additional data are needed to test these various theories., esweciallv- in view of Dorn's9 ork. which indicates that the activation energy for creep is independent of the stress and strain. The present paper presents the stress-strain data derived from incremental loading of magnesium single crystals in tension and direct shear, in the temperature range of 78" to 364°K. Incremental loading was employed in order that the creep component of the strain could be determined. Stress-strain curves of aluminum10-13 and copper" single crvstals. derived from incremental loading tests, have been found to be in agreement with those obtained by the more conventional constant strain rate or loading rate tests. Two types of tests were conducted in the present investigation: 1) tests in which the temperature was maintained constant throughout the entire

Jan 1, 1958

By P. W. Bridgman

It is a commonplace that experimental physics in the last few decades has discovered manifold complexities in the atomic and subatomic levels, where it was thought for hundreds of years that no structure existed, as is witnessed by the derivation of the word "atom" itself. The field of exploration opened by the discovery of the electrical structure of the atom was so fundamental, rich and stimulating, that it has been almost exclusively cultivated by physicists since they obtained their first intimations as to the nature of the basic facts. Only within the last few years has it begun to dawn on us that we have overshot an enormous domain in which are situated many phenomena of fundamental importance for all the practical uses to which we put matter in our daily lives; the domain, that is, of most of the phenomena of interest to the biologist and the metallurgist. Furthermore, we are beginning to find that this intermediate domain is not entirely simple, but that it contains unsuspected complexities, some of them derived from the complexities of structure on the atomic and subatomic levels, and some of them emergent as matter collects itself into large aggregates, which often offer the key to the explanation of hitherto baffling large-scale properties of matter. Today I want to describe and consider some of these newly discovered complexities in the behavior of matter in bulk. The application to metallurgical problems is not always direct, but I hope to be able to suggest that such general notions as to structure as those here discussed must have important reactions on our attitude toward the problems of metallurgy. Three different sorts of phenomena of this kind to which I shall direct your attention are (1) the so-called structure sensitive phenomena, (2) complexities of such a nature that they are masked by the presence of extraordinarily small amounts of impurities, and (3) complexities depending on internal molecular rearrangements which can be understood only from the point of view of the quantum theory.

Jan 1, 1931

FEW whose good fortune it has been to gaze on the Utah Copper mine but will agree that it is one of the two or three most magnificent man-made spectacles in the world. Skyscrapered Manhattan Island perhaps is more inspiring; but there the effect is obtained by aggregating a thousand separate units. The Utah mine is a single thing- the biggest thing that men have made. By the end of 1931 there had been moved at Utah 222,000,000 cu. yd. of material, including ore and the waste rock that overlay it. This figure will be increased at an average rate of nearly 20,000,000 yd. per year. Excavations for the Panama Canal are estimated at 232,300,000 cu. yd., but the Canal is 50 miles long, and it is impossible to obtain a comprehensive view of the whole project at one time. The spectator, on the other hand, need only walk part way up the east slope of Bingham Canyon to see unfolded before him the whole panorama of the great copper mine. In the foreground is a huge pit bottomed for the time being 100 ft. below the normal floor of the canyon, which also is the elevation of the main railroad yard. Here from 500 to 800 standard steel railway cars, each of 80-ton capacity, are assembled daily to carry the ore to the concentrators. But the main part of the mine and that from which ore is now coming lies above this level. As can be seen in the accompanying photograph, a series of terraces or benches reaches to the top of the mountain that projects between the main branch of Bingham Canyon and Carr Fork. From bench A (the yard level) to bench W is a vertical distance of 1500 ft. In height the benches vary from 40 to 70 ft. and in width from 30 to 450 ft. The lower benches, as they skirt the mountain,

Jan 1, 1933

By Werner Ostertag

A series of rare earth cobalt compounds of the composition RCoa (r = Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, Ev, Tm, Lu) has been prepared. The compounds crystallize in space gvoup R3m and are isomorphous with PuNi3. Except for CeCo3 and PrCo, the series shows decreasing- values of a. and co. The relalively small parameters of CeCo, and PrCo, are explained by valencies of cerium or praseodymium which exceed the usual rare earth valency of three. The structure of the compounds is discussed as in-fillings of kagome nets in direct and staggered superposition. In the course of a systematic investigation of rare earth cobalt compounds"2 and their magnetic properties,, a series of alloys corresponding to the formula Rco3 has been prepared. The investigation of the Rco3 series was stimulated by our investigation of the yttrium cobalt system2 as well as by reports in the literature: Smith and Hansen4 reported the structure of YcO3 and Van vucht5 that of GdCo3; ceco3,6 Gdco3,7 and DyCo3 7 have been found to be single-phase during phase diagram studies. It was the purpose of this work to report crystallographic data on the entire Rco3 series and to interpret the structure of these compounds on the basis of general principles as discussed by Frank and Kasper.8 At the time this work was terminated, it was learned that a similar investigation has been carried out independently by Bertaut, Lemaire, and schweizer.9 Except for CeCo3 (ao = 4.952, co = 24.73') and NdCo3 (a0 = 5.067, co = 24.76') data of this work are in satisfactory agreement with their investigation. EXPERIMENTAL TECHNIQUES A series of samples having the composition Rc03 was prepared from stoichiometric amounts of the rare

Jan 1, 1968

INTRODUCTION Within the past few years Clark (1972), King (1970), and King, et al. (1973), have summarized porphyry molybdenum occurrences. Clark (1972) includes as porphyry or stockwork deposits some occurrences more recent exploration has shown to be of other genetic types. King (1970) and King, et al. ( 1973) provide broad general descriptions that unfortunately are restricted to the US. Nor does the King, et al. (1973) description have benefit of the Wallace (1974), Hall, et al. (1974), or Giles (1975) data on alteration, fluid inclusions, or isotope chemistry. The synthesis presented here up- dates these older summaries, eliminating all but the well established porphyry molybdenum deposits as well as enumerating the unifying characteristics displayed by these deposits within the Cordillera of North America. This type of deposit occurs in the South American Andes as well, but Andean deposits are not well documented so only North American Cordilleran deposits are considered. Stockwork, porphyry, and Climax type molybdenum deposits are synonymous geo- logical labels for the large molybdenite de- posits found in parts of the western Cordillera of North America (Khruschov, 1959). These labels describe and define the type of deposit discussed herein. The term porphyry is preferred for this chapter because it describes the common characteristics; it separates the molybdenum deposits from the porphyry copper deposits, which have many similarities but also important differences. This usage also eliminates blanket application of the word stockwork to breccia pipe deposits such as Boss Mountain in British Columbia. J. R. Woodcock has contributed much to this chapter; his influence, original data, and thoughtful comments qualify him as co-author. Porphyry molybdenum deposits are characterized by fine-grained molybdenite occurring alone or with quartz and/or pyrite in fractures and open spaces of stockworks and breccias. The molybdenite is generally less than one millimeter across and in many cases too fine-grained to be seen with the aid of a hand lens. Occasionally some deposits con-

Jan 1, 1978

By Reinhard H. Wöhlbier, George E. Aiken

8.4-1. Introduction. Surface excavating is done on a continuous basis with a variety of machines: 1) trenchers and ditchers, 2) conveyor loaders, and 3) bucket-chain and bucket-wheel excavators (BWE). Surface mining is largely concerned with only the last two machines, although some of the conveyor-loader types are often used by contractors for large-scale earth moving, and the engineer should be aware of these applications. This chapter is restricted to discussing only the bucket-chain and bucket-wheel excavators, with special emphasis on the latter. Continuous digging with these machines is done with evenly spaced buckets on either an endless chain or on the periphery of a rotating wheel. The bucket-chain digger excavates and takes the material away from the face with the same machinery. In the case of the bucket-wheel machine, these two functions are separate. Material is excavated by the buckets and then flows in a continuous stream via a transfer to the conveyor system, which in turn transports it to the discharge point. The wheels are adjustable in rpm and mount 6 to 12 buckets of equal size. These are classed as celled, cell-less or semicelled. The digging ladders for both types can move simultaneously in the horizontal and vertical planes. Ladder control is similar to the operation of a bucket-line dredge. Some ladder-chain and all wheel excavators have the machinery deck and superstructure mounted on a 360° swing circle. Other chain diggers have a fixed machinery deck. Deep and/or high cutting models are available in either the chain or wheel excavator. Machines can be either rail or crawler mounted, but the trend is to crawlers. Many of the early ladder-chain, rail-mounted excavators have been converted to crawlers. These may be either of the single or bogie type, depending on the conditions. Large machines usually use the superior three-point crawler suspension.

Jan 1, 1968