Search Documents

By Warren L. Howes

THIS paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. FLOWSHEET The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybdenum-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day. [t] Fig. I shows an abbreviated flowsheet of the grinding section of the mill. PRIMARY BALL MILL A 3-ft. Symons shorthead crusher in open circuit crushed to ¼ -in. maximum one-way dimension the feed to the 5 by 10-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. [ ] In order to clarify the difference in design of the various types of liners used, Fig. 2 shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I.

Jan 1, 1943

By Sydney H. Loram

TEIS paper, which is merely an arrangement of data collected during several hurried journeys, is offered to serve as a record, until such time as a better substitute be compiled. My observations were confined, as far as possible, over the entire distance, to the actual river valley; because near the Central Cordillera the country is so mountainous as to be im; passable in any direction but that of the dominant valleys. The river is not navigable anywhere, and for the first part of its course is a mountain torrent that runs down the bottom of narrow, almost vertical-sided valleys, through which the only road requires repeated fording, and often following up the bed of the stream ; but the rock-walls, standing clean and free from debris on either side, present the different formations with remarkable distinctness. A topographical map and a cross-seetion of the Rio Huasco is given in Fig. 1. The Rio Huasco practically rises from Laguna Grande, a lake about 17 km. from the Argentine boundary, and 3,135 m. above se-level, which is fed by direct snow-water, and by a few streams varying from a considerable volume, when supplied by the melting snow, in late spring, to little or nothing during the rest of the year. It is a somewhat pear-shaped body of water, about 1.5 miles in length and half a mile in average width, with a reported maximum depth of 45 meters. It was formed by the choking up of a narrow continuation of the same valley with blocks of an agglomerate mentioned later. The present level is some 5 m. below high-water mark (to which point, according to local accounts, it has not been filled for 35 years). In the intervening margin is a calcareous deposit about 4 m. thick, formed by the rapid evaporation of the water in the exceedingly dry air, and aided by the capillary action of an aquatic plant, growing in thick masses around the edge of the lake. These masses, dying and banking up, form

Jan 1, 1905

EDWARD W. PARKER,* Philadelphia, Pa. (written discussion ?).-The two papers on coal-mine costs and pride fixing that Mr. Norris has contributed to the Transactions possess as much general interest and are of as much value to the coal-mining industry as any papers that have been presented in recent years. Until recently one of the troubles with the coal business, and especially the bituminous branch of it, has been that because of the lack of a uniform system of cost accounting (many operators, I regret to say, not having had any system at all), the industry as a whole may be said not to have known where it was at. The system adopted by the Federal Trade Commission may not be absolutely perfect but it has accomplished something in that it has compelled a uniform method of reporting and tabulating costs giving results of these compilations which are comparable. The Institute and the coal-mining industry owe a vote of thanks to, and of confidence in, Mr. Norris and his two associates on the Engineers Committee of the Fuel Administration, Messrs. Garnsey and Allport, for the great work they have done in interpreting the results compiled by the Federal Trade Commission, not to speak of the personal sacrifices made by them in giving their services to the government. Those who have read Mr. Norris' paper will probably join me in wishing he had brought out a little more fully the real meaning of the charts so far as they indicate the difference between the cost of producing a ton of anthracite and the price the operators receive for their product. Mr. Norris could have done this more satisfactorily than anyone else. It seems to me that particular attention should be drawn to the fact that, according to these charts, and the tables accompanying them, not less than 25 per cent. of the total output of anthracite, whether "company" or "individual," during the period covered by Mr. Norris' paper,

Jan 4, 1919

By L. J. Buck

Lead smelting in the ore hearth, first practiced in Europe, whence the traditional name "Scotch hearth, and later developed in America to its present efficiency, is based upon the roast reduction process and is applicable to relatively high-grade galena concentrates. The roast reduction process embraces not only the roast reactions: 2PbS + 70 = PbO + PbSO4, + SO2 PbS + 2PbO = 3Pb + SO2 PbS + 2PbSO4 = Pb + 2PbO + 3SO2 but also, by reason of the addition of extraneous fuel, the reduction reaction: 2PbO + C = 2Pb + CO2 Thus in the ore hearth the roasting of lead sulphide, forming lead oxide and lead sulphate, the reaction of lead oxide and lead sulphate with lead sulphide producing lead, and the reduction of lead oxide by carbon producing lead, go on simultaneously. The Ore Hearth Function of the Ore Hearth.—The ore hearth, through the roast reduction process, provides for the extraction of lead and the immediate disposal of the smelting products—fume, hearth slag and lead, all of which are subsequently treated as follows: the fume is recovered in the flue system and baghouses, mixed with concentrates, and returned to the ore hearth in the form of ore mix; the hearth slag is smelted in a blast furnacc for the further recovery of lead; and the lead is refined and cast into a marketable product. Concentrates Amenable to Ore-hearth Smelting.—Only concentrates that are high in lead content, 70 per cent or more, are ordinarily considered amenable to ore-hearth smelting. Silica should not exceed 2 per cent and iron is allowable only to 4 per cent. These slag-forming constituents occlude both sulphide and mctallic lead, prevent the elimination of sulphur and decrease the lead extraction. Lime and magnesia are beneficial in that both favor a dry slag, promote elimination of sulphur, and prevent occlusions of metallic lead.

Jan 1, 1937

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues through-out the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1933

By E. Stansfield

IT. has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collec-tion, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By F. L. Wolf

THE tests here described were made to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven, and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three are equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which are lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the electric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 cm.) wide, 83 in. (210 cm.) high, and 79 in. (200 cm.) deep, inside measurements. The walls are constructed in, panels about 18 in. (46 cm.) wide and 4 3/16 in. (10.6 cm.) thick, packed with blocks of insulating material and covered with sheet iron. The concrete floor on which the ovens set is 13 in. (33 cm:) thick. A recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported. on I beams serve as' supports for the trucks and racks. The ventilating system consists of a Sirroco No. 1 ½ fan, connected so as to draw air from the top of the-oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan and pipes are covered with ¼ n. (6.3 mm.) asbestos cement lagging.

Jan 4, 1922

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-' ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration 'of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

By H. l. Burghoff, D. E. Lawson

The presence of tellurium in copper and, by inference, in copper alloys, has been considered seriously detrimental and has been avoided. In particular, very small amounts of tellurium have been found to produce red-shortness, although the effects on cold-working and ordinary physical and mechanical properties have not been known so definitely. References in the literature are few, but as long ago as 1881, Eglestonl reported that 0.083 per cent tellurium in fire-refined copper rendered the copper red-short and therefore worthless for hot-rolling. In hot-rolling copper cakes containing this amount of tellurium, he found that fine cracks appeared in the cakes on the first pass through the rolls, the cracks opening further in successive passes. When cold, the metal was said to be tough and malleable. A few years ago, during the course of an investigation in our laboratory on copper-base alloys, it was found that tellurium-bearing alloys could be machined much more freely than similar alloys not containing tellurium. The study was pursued further in this direction, and considerable data were obtained, which indicated that certain tellurium-bearing alloys might have properties of commercial interest. The work eventually led to patent protection,2 a wide range of tellurium-bearing copper-base alloys being covered. This article presents results obtained on the effect of tellurium on the mechanical properties of three copper-base alloys: commercial bronze (90 Cu, 10 Zn), 1.5 per cent tin bronze (98.5 Cu, 1.5 Sn), and silicon bronze (96 Cu, 3Si, 1 Zn). Several alloys were cast in each series, with tellurium content ranging from 0 up to about 1 per cent. The alloys were melted under charcoal in a clay-graphite crucible, using a high-frequency induction furnace, and were cast without undue difficulty in rod form, 15/8 in. in diameter. Charges for the zinc and tin series were made up from the following materials: cathode copper, electrolytic zinc, tin, and tellurium in slab

Jan 1, 1938

By Alan Bauer

DRILLING CONSIDERATIONS In considering blasting it is necessary to consider the drilling and explosives since one is generally concerned with the total cost of muck of a certain size in the pit or through the crusher. To get a current idea of the drilling situation in open pit mines plotted in Fig. 1 are the drilling costs per ton of material vs. hole diameter for rotary drill holes in large limestone, iron ore and taconite operations. The exception is the 2-in. diam hole which was drilled with a percussion drill in limestone. Each curve in Fig. 1 represents a different operation and the data cover many months of production drilling. The costs are total operating and maintenance and do not include machine depreciation. As the hole size is increased so are the machine size and the investment. Providing the tonnage is available to be drilled, then as the machine size goes up so does the productivity-markedly-and this same shape of curve applies. In some instances it is even steeper. The interesting thing to note is that in each case studied there is a substantial drop-off in cost/ton as the hole size is increased. This is true for the softest material considered, limestone, through to the hardest, taconite. How has this come about? In going from 10-in. to 123-in. diam holes, the powder factors have generally stayed about the same and the same type of muck has been produced. To date this has been mainly in the softer materials but it has also been steadily taking hold in the harder ones. On this basis, then, patterns are generally expanded as the ratio of the hole diameters or close to it, if the explosive type is kept the same. In the harder rocks the cost per foot of hole has increased somewhat so that the overall reduction in drilling cost per ton is about 25 pct. In somewhat weaker rocks of about 25,000 psi compressional strength the drilling cost per

Jan 1, 1968

By W. A. Lang, K. C. Gilbart, E. Stansfield

It has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collection, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By D. I. Bardos

The occurrence of Laves phases (AB,) in various binary alloy systems has been reviewed in recent papers.13 Iron forms Laves phases with Sc-, Ti-, V- and Cr-group elements. However, two of the corresponding Laves phases with cobalt, namely MoCo, and WCo,, are missing. Nickel forms binary Laves phases with Sc and Y, but not with any Ti-, V-, or Cr-group element. These conditions are schematically illustrated in Table I. That electron concentration is a significant factor in determining which type of Laves phase is formed in a given case was recognized long ago by Laves and Witte,4 This concept has been more recently applied to Laves phases formed by transition ele-ments. It now appears that the average electron concentration (average number of electrons per atom outside of the closed shells of the component atoms) may be an important factor also in determining whether or not a Laves phase can occur at all in a given system. As shown in Table I, in the transition element systems considered Laves phases are absent at electron concentrations of 8, or larger (to the right and below the double line in Table I). These absences clearly cannot be accounted for on atomic size considerations, as evidenced by the many inconsistencies apparent in Table 11. While the ideal radius ratio for Laves phases is 1.222, in the systems which do have Laves phases the ratios of CN 12 radii range from 1.10 to 1.46. The consistent absence of Laves phases at RA/RB< 1.10 might be attributed to the low values of these radius ratios. However, Table II shows that absences also occur irregularly throughout the radius ratio range covered. In a previous paper7 it was concluded that, in transition element systems forming u-phases, silicon may act as an acceptor of electrons, thus stabilizing the u-phase at electron concentrations higher than

Jan 1, 1962

By J. A. Bownocker

THE EXISTENCE of petroleum in the rocks of Ohio and Indiana seems to have been first shown by wells dug for salt. The fuel, however, was objectionable owing to its odor and inflammability. Not until the brake well was drilled in 1859 did the people appreciate the value of rock oil, and then they at once began plans to secure the coveted fuel.. The first successful well in these two states was near . Macksburg, in southeast .Ohio, where at a depth of 59 ft. (17 m.) :oil was found in commercial quantity (1860). A year later this fuel was secured on Cow Run, in the same county, and at about the same time in Noble, Morgan and perhaps other counties in that part of Ohio. The second great step in the production of oil in Ohio and Indiana was taken in 1884 when the reservoir of natural gas in the Trenton limestone of northwest Ohio was tapped, and where a year later oil was secured in the same formation. Petroleum in this limestone was obtained in Indiana in 1889.1 The third step in the production of oil&apos; in Ohio and Indiana is associated with the Clinton sand of Ohio. Natural gas in large volume was discovered in that rock at Lancaster, in 1887, and the area has been extended until it has become the largest individual producer in the world. The presence of natural gas in such great volume all but demonstrated to the driller that-oil lay hidden near by. Soon the search for it was started but not until 1899 was petroleum in commercial quantity found in the Clinton sand, and a large pool was not located in it until 1907. The fourth step in the development of the industry was taken in 1913, when the pool in Sullivan County, in western Indiana, was opened. The producing rock is the Huron sandstone, which is the topmost member of the Mississippian system.2

Jan 2, 1920

By W. B. Hincke, C. G. Maier

Commercial processes of lead softening directly involve the behavior on fusion of mixtures of the oxides of antimony and lead, and the vapor pressures of these materials. Practically no quantitative data have been available for the discussion of lead softening from the point of view of the fundamental metallurgy of the process. The Pacific Experiment Station of the United States Bureau of Mines, in cooperation with the University of California, in the course of its program of study of the fundamental properties of oxides and sulfides, recently made vapor pressure measurements upon the various forms of pure antimony trioxide.1 When these measurements were considered in connection with the softening and "fuming" furnaces which are often used for lead purification, an unexpectedly anomalous condition appeared. In brief, this anomaly consisted in the fact that in certain softening furnaces, where lead bullion of approximately 1 per cent antimony content was being treated at a temperature of approximately 1300" F., no appreciable volatilization of antimony occurred, there being produced only a "skim" containing from 15 to 20 per cent Sb, 65 to 60 per cent Pb, as mixed oxides. In the "fuming furnaces," where the temperature was only about 1400" F. and where an accumulation of "skims" from the primary softener was being treated with certain other antimony-containing materials, a considerable volatilization of antimony as oxide occurred; an "impure" skim of some 60 to 65 per cent Sb and 10 per cent Pb was also produced as mixed oxides. The latter material cannot be suitably treated in hearth-type or softener furnaces. The essential chemical difference between the first and second step is the customary use of some reducing material (such as petroleum coke) in the later operation. An obvious interpretation of the effect of coke in facilitating the fuming of the antimony is the supposition that the antimony may be reduced to metal, and volatilized as such. This supposition is improbable, however, when it is realized that a slight extrapolation of the vapor-

Jan 1, 1932

By A. Q. Tool

THE necessity of accurate temperature measurements in the glass-making industries is today being much more widely appreciated than in the past. The introduction of the modern simplified and perfected pyrometric methods in connection with exact regulation of furnace temperatures has caused a marked improvement in the glass product with a quickened rate of production. An example of the processes in which much improvement has been and still can be made is that of annealing or heat-treating the glass. This is one of the most delicate processes in glass manufacture and one that requires a most careful furnace control. The heat treatment is undertaken to decrease the possibility of breakage and, in glass for fine optical instruments, to prevent serious warping of accurately ground and polished surfaces and to make the glass more uniform throughout to the passage of light waves. These objects are accomplished by removing all the harmful stresses that exist in a piece of glass when it has been cooled too quickly or unevenly. Such stresses exist, for example, after it has been pressed, cast, or otherwise worked. Thus the process of annealing consists of heating the glass evenly to the temperature at which it softens just enough to relieve these stresses in a reasonable time and then cooling slowly and uniformly until the glass hardens again. Accordingly, the things that must be investigated and determined in order to anneal glass without loss of time are, the annealing temperature, the time that the glass should be held at this temperature while the stresses relax, and the quickest cooling procedure that will give satisfactory results. After these characteristics of the glass are known the problem is one of pyrometry and temperature control entirely. In cases when it is known that a glass article will be required to withstand some definite type of heat or mechanical shock it is often possible, by a proper heat treatment, to produce such a distribution of the stresses in the glass that it will be enabled to resist these shocks more effectively.

Jan 9, 1919

By M. E. Wadsworth, K. J. Richards

The oxidation rates of tantalum in various partial pressures of carbon dioxide in the temperature range 700°to 950°C were measured with a thermo-gravimetric balance. Oxidation involved a surface -controlled reaction associated with the formation of a nonprotective layer of Ta2O5. Below about 720°C, there was a change in the rate-determining mechanism, and above 830°C the linear rate was preceded by a complex region of nonlinear oxidation behavior. The linear oxidation of tantalum has been explained quantitatively in terms of carbon dioxide adsorption, followed by a rate-controlling surface reaction. The initial adsorption has been expressed both as an equilibrium process and as a steady-state reaction. The enthalpy for chemisorption of CO, was determined to be -17.3 kcal per mole. The surface-controlled reaction had an activation enthalpy of 40.4 kcal per mole. A considerable amount of interest has been shown in recent years in the oxidation of tantalum and the nature of the oxide film produced. This interest is associated with the increasing demand in our technology for structural materials to withstand high temperatures and corrosive atmospheres. The low oxidation resistance of tantalum has severely restricted its application as a high-strength, high-temperature material. As a fundamental approach to the realization of the full poten- tials of this metal, the kinetics of the oxidation of tantalum in oxygen and air have been extensively studied; however, very little work has been reported on the effect of other gases, including carbon dioxide. According to Miller,&apos; the only reported study of the reaction between tantalum and dry carbon dioxide is a restricted observation by O&apos;Driscoll et al.2 at 8 atm absolute pressure and 500°C. Therefore, this study was made to investigate the reaction of tantalum with carbon dioxide. EXPERIMENTAL MATERIALS AND METHODS The vacuum-annealed tantalum used in this study was obtained from Fansteel Metallurgical Corp. as 0.025-mm-thick sheet stock. This material had less than 0.1 pct total impurities, and the maximum individual impurity concentrations were

Jan 1, 1964

By C. A. Lemke

The ores now milled at the Midvale concentrator of the United States Smelting, Refining & Mining Co. come mostly from the company&apos;s mine in the Bingham district, about 18 miles west of Midvale. Custom ores from this same district and from other western mining districts are also milled at times. The Bingham ores consist of galena, pyrite, chalcopyrite, and sphalerite in a gangue of quartz, quartzite, limestone, and porphyry. The percentage of chalcopyrite is small, usually about 0.5 per cent., while the galena, pyrite, and sphalerite combined constitute about 60 per cent, of the total ore. These three minerals vary considerably in amount and, at times, all three are somewhat oxidized. The ores also contain gold and silver, the former being mostly in the pyrite while the latter is generally with the galena. The crystallization of the economic minerals varies from fairly coarse to extremely fine. The ores are carried to Midvale by the Bingham & Garfield and the Los Angeles & Salt Lake railroads or by the Denver & Rio Grande Western railroad, in 50-ton, steel, full dump cars. The milling problem is to recover the silver-bearing galena, the gold-bearing pyrite, and the chalcopyrite in a product suitable for the lead smelter and containing the least possible amount of gangue and sphalerite and then recover the sphalerite in a product suitable for a zinc smelter. The minerals are recovered partly by water concentration and partly by water concentration combined with electrostatic treatment. Gravity Concentrator The gravity concentrator has a capacity of about 465 tons in 24 hr. The mill buildings are of wood. The mill was built in 1905 to handle approximately 90 tons in 24 hr.; since that time several additions have been built and various changes have been made in the flow sheet. The last extension, which raised the capacity of the mill to its present level, was built in 1915. The additions to the mill building have not kept pace with

Jan 1, 1926

By F. L. Vogel

Densities and distributions of dislocations in plastically bent germanium crystals before and after annealing were studied. In the bent and annealed crystals, the theoretical relationship between radius of curvature and density of dislocations is confirmed. Before annealing, however, more dislocations are present than required, and these are distributed with a minimum at the neutral axis and maxima at the top and bottom surfaces. On annealing, three significant changes occur in the bent bars: 1) the average dislocation density is reduced, presumably by the annihilation of opposite signs; 2) dislocations migrate from the high density outside regions toward the low density neutral axis, thus producing the equilibrium distribution of dislocations; and 3) a polygonized structure is formed by movement of the dislocations into walls normal to the slip plane. ETCHING to reveal edge dislocations&apos;-" offers a unique opportunity to study, in germanium single crystals, the functioning of dislocations in plastic deformation. Plastic bending is ideally suited to this purpose because it produces a static array of edge dislocations in an ideally plastic material which is predictable from the theory." " Nye" has given a rather complete treatment of the geometry of bent crystals in terms of dislocations. The density of excess dislocations is related to the radius of curvature of the slip plane of a bent crystal, as shown in Fig. 1, assuming the absence of macroscopic elastic stresses. The curvature of any plane in the zone of the bend axis is found by resolving the Burgers vector into that plane, so that for the usual case where the slip plane is inclined at some angle 0 to the neutral plane of the bar, the equation applies, with T equal to the radius of curvature of the neutral plane of the bent crystal. Two predictions which are relevant to this study may be made from Eq. 1. First, in crystals bent to various radii, the average excess dislocation density is inversely proportional to the radius and second, for a bar bent to a radius which is large compared with its thick-

Jan 1, 1957

By William F. Brace, Howard R. Pratt, Wayne S. Brown

In many engineering structures, the mechanical properties of large volumes of rock must be considered. Typically, such properties are assumed to be the same as those of small laboratory samples, although it is clear that the laboratory samples do not contain the joints, faults, and other natural planes of weakness of the rock mass. A cheap, convenient testing procedure is needed with which the engineer can more accurately assess the strength and elastic properties of natural jointed rock. As a first step in this direction, a test has been developed capable of determining mechanical properties of large samples in their natural undisturbed state. In the present paper, some preliminary experiments on relatively unjointed material are described. Numerous attempts have been made to measure the deformation modulus of rock masses with varying degrees of success. Rocha (1), Grimm (2), and Alexander (3) have placed flat jacks in a slot in the rock and measured the pressure required to deform the slot. Bonnechere (4) has grouted large flat jacks in granite masses and performed similar experiments using a variety of strain measuring techniques. The U. S. Bureau of Mines has conducted radial jacking tests in which a uniform radial stress is applied to the inside of a tunnel of circular cross section and radial deformation is measured by extensometers located at various depths in the tunnel fall. Plate jack tests (Rocha (5), Shannon and Wilson (6)), pressure chamber tests, and cable jacking tests (Zienkiewicz and Stagg (7)) have all been used to determine in-situ deformation modulus. Several bore hole techniques have also been used to measure rock deformation. These include bore hole jacks (Goodman (8)), bore hole dilatometers using expandable membranes (Menard (9)) and bore hole penetrometers. Most of the above tests except the radial jacking test have an unknown stress distribution and require considerable approximation to calculate a deformation modulus. These approximations include the use of elastic theory for solutions of rigid plates, thick-walled cylinders, etc., and determination of values for Poissons

Jan 1, 1971

By R. W. Mancantelli, J. R. Woodward

IN 1947 a large low grade deposit of uranium was located in the northwest corner of Saskatchewan, in the Beaverlodge property of Eldorado Mining & Refining Ltd. Most of the values occur as thin seams and as coatings on other minerals, and the ore, which is light and friable, is not amenable to the usual gravity methods of concentration. The acid leaching process developed to retreat the company&apos;s Port Radium tailings was also impractical, as the percentage of carbonates is high and the percentage of sulphides relatively low. Construction of the mill building and installation of equipment, both scheduled for 1952, awaited selection of a satisfactory ore dressing process on or before Oct. 1,1951. An extensive research program on dressing of ores from the Ace mine therefore was undertaken by the Mines Branch in Ottawa, a research team at the University of British Columbia, and an ore dressing group at the company&apos;s Port Hope refinery. Pilot plant operations were conducted at the Ottawa plant of Sherritt Gordon Mines Ltd. under the general direction of C. S. Parsons, consultant on metallurgy and ore dressing for Eldorado. In mid-September, having compared results of the several research programs, Dr. Parsons recommended a process employing a carbonate or basic leach. He reported that, while the chemistry of the process had been proved, engineering of the flowsheet was incomplete, and he suggested that under normal conditions further pilot plant work at the Ace mine might be profitable. However, since this would involve a delay of 12 to 18 months in bringing the property into operation, he recommended that design of the concentrator proceed immediately. Concentrator capacity was determined by two considerations: 1) the amount of ore then available and 2) the expectation that continued improvements would be made in the ore dressing process as a result of the intensive research being carried out by the Mines Branch of the Department of Mines and Technical Surveys. As these improvements could affect both the chemistry and the en-

Jan 1, 1956