Search Documents

Payloader The Frank G. Hough Co. has made available another four-wheel drive tractor-shovel. It has a 1 cu-yd bucket with 60 hp Diesel or 54 hp gasoline power optional. The use of large pneumatic tires, same size all around, and drive on all four wheels gives this new Payloader traction to work effectively in sand, mud and snow, and travel on pavements with- [ ] out injuring the surface. Rear wheel steer with power booster plus short wheel base makes it easy to operate and highly maneuverable. Four speeds in both directions insure fast travel speeds for transport and fast operating speeds on shuttle loading or similar operations. Bulldozer blade, crane hook, fork lift and snow plow attachments are available, quickly interchangeable with the bucket to further increase its multi-purpose usefulness. Circle No. 1

Jan 1, 1952

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

E. D. Peters, Jr., Dorchester, Mass.: This paper of Mr. Keller's seems to me a step in a direction that has been very little exploited, and iff likely to lead to valuable practical re-

Jan 1, 1899

By Allan D. Taylor

INTRODUCTION From the designer's view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do's and don'ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn't Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By W. H. Morris

I have been requested to present a paper on the slag from the basic Bessemer process, as prepared for fertilizing. Since Professor W. B. Phillips presented at the Birmingham meeting, in May, 1888, an able paper* on this subject, as it had been developed up to that time, there is little for me to add. Perhaps later practice may be best expressed by the homely proverb, " The proof of the pudding is in the eating." As the Pottstown Iron Company is the only concern manufacturing basic Bessemer slag in this country, the writer's personal experience in the use of it may be interesting. Our slag averages: P2O5, 21.37; SiO2,, 5.10; MgO, 5.90; Al2O3, 4.01; MnO, 5.56 ; FeO, 12.00; Na2O and K2O, 0.80; CaO, 45.26; total, 100.00. This gives over 76 per cent. of phosphoric acid and lime. In using this material for several years past on my lawn and garden, I have found it better than anything else I have ever tried ; and I am sure that any of you who had seen my green grass last month (January), wherever the ground was bare from snow, as bright as in early fall, would be forced to acknowledge the advantages of this soil-enricher. The grass on my private lawn, and around the company's office, is green the whole winter; and we have raised very good sod, by the use of this phosphate, where, without it, we were unable to get the grass to grow either from seed or by repeatedly sodding. The same statement applies to garden-truck; when the soil was first broken up, a good crop of vegetables was easily raised. My own gardener has had several premiums from Philadelphia seedsmen (notably, last year, the first premium for sugarcorn raised in the first part of July, being the first sample sent them). Our method of applying this material is to grind the slag very finely, so that at least 60 per cent. of it will go through a 150-mesh screen (i.e., say, 22,500 meshes to the square inch), and 90 per cent. through a 100-mesh screen (i.e., 10,000 meshes to the square inch). This fine grinding seems to be the main condition of success.

Jan 1, 1893

By R. P. Rothwell

IN January last I published in the Engineering and Mining Journal a table giving, with a considerable degree of accuracy, the production of anthracite coal for the year 1874. At that time it was impossible to give any correct estimate of the production of bituminous coal, for the returns I had been able to secure from such distant and scattered districts were not always forwarded punctually, and the work of -obtaining anything like a true estimate of the coal mined in districts from which I was unable to obtain official returns was both laborious and tedious. As will be seen from the detailed reports furnished herewith, I have succeeded in obtaining tolerably accurate returns of 20,093,704 tons; and upon careful revision by numerous well-informed local authorities, my first estimate of the amount of coal not officially returned to me has grown very considerably; indeed, as I get more information on the subject I find that our bituminous coal production greatly exceeds the amount we have been accustomed to hear it placed at, aggregating as it does, 26,465,704 tons. Mr. Andrew Roy, State Inspector of Mines for Ohio, has reported the production of Ohio at 4,168,445 tons, while his first estimates were but 3,820,000 tons; and similarly, in other cases, the more full the returns direct from the mines the more incorrect do I find all previous reports. I am able now to furnish, not an accurate statement, indeed, but by far the most full and reliable one that has yet been published of our coal production. The amount of labor involved in obtaining this admittedly imperfect report has been simply enormous. In the following tabular statement it will be perceived that Pennsylvania produces nearly one-half of all the bituminous coal mined * Since this paper was read fuller reports from some of the States whose production had been "estimated" have modified the figures given. The most serious error is in California, which produces probably 200,000 tons less than these figures. Oregon and Washington territories also yield smaller amounts than here reported; but these reductions are probably fully compensated by fuller reports from other States that were here underestimated. The correct aggregate amount will not vary much from that here given. Early in 1876 I will be able to give a fuller and more accurate report for the year 1875.

Jan 1, 1875

By R. E. Tate, L. J. Herman

We have had occasion to produce wire of Np-237 in small diameters for use in some chemical experiments. Since the mechanical metallurgy of neptunium has not been investigated extensively, it seems desirable to report our successful extrusion technique. Because of the neptunium activity and its attendant health hazard the experimental work was done in glove boxes and related equipment also used for Pu-239. At room temperature a phase neptunium' is a hard (Dph -355) orthorhombic metal of high density (p = 20.45 g per cu cm). a neptunium transforms2 to tetragonal ß neptunium at about 280°C and this in turn transforms to bcc y neptunium at about 577°C. The y phase melts at about 637°C. A temperature of 340° to 345°C was selected for the extrusion, this temperature being a compromise be- tween a possible advantage of working with the presumably more plastic cubic y phase above 577°C and the risk of having the neptunium react with the alloy steel die to form the low-melting Fe-Np eutectic. A 0.75-in.-long, 0.26-in.-diameter ingot of good-purity* Np-237 was extruded by the direct *C = 230 ppm, Pu = 200 ppm, thirty-five metallic elements below limit of detection by spectrographic methods. process through flat-face orifices to form several sizes of wire ranging from 0.010 to 0.030 in. in diameter. Molybdenum disulfide was used as the die lubricant. The extrusion was done in a vacuum of about 10-4 torr to reduce reaction of the neptunium with atmospheric gases. British workers3 at Harwell have extruded neptunium under similar conditions. The force required to extrude 0.010-in.-diameter wire at the rate of 4 in. per min was 6000 lb, as measured with an electrical load cell. Wire 0.020 in. in diameter was extruded with a force of 4700 lb at a rate of 2 in. per min, and wire 0.030 in. in diameter was extruded with a force of 4000 lb at a rate of 1.3 in. per min. An extrusion constant, c, can be computed from the measured forces, P, for the equation4 P = c log-A/a where A/a is the extrusion ratio or the ratio of the cross-sectional areas of the container and the

Jan 1, 1965

Some years ago the open Hearth Committee of the Institute reached the conclusion that the reading of "set" papers tended to preclude the specific and detailed discussion of specialized problems of current interest to those operating steel plants. As an innovation the Committee distributed in advance of the meeting in May, 1927, a questionnaire containing a list of 27 topics involving operating problems. The subsequent discussion of the questions, participated in by 37 members, was a conspicuous success. Semiannual meetings have been held since; and at the conference of November, 1929, at Chicago, 131 men were present and the minutes comprised a book of 133 printed pages, thereby, indicating the growing value of the conference in the eyes of both the metallurgists themselves and the companies that employed them. With this example in mind, the Directors felt that definite advantages would accrue to a similar conference to be participated in by smelter officials and metallurgists engaged in the operation of copper reverberatory furnaces. The settlement of the Carson litigation, which for several years had virtually stopped public discussion of reverberatory practice, offered an opportune time for launching the scheme. Although the Conference may become largely self-financing in the future, some funds were regarded as necessary to conduct the first meeting. The members of the Rocky Mountain Income Committee, in view of the fact that copper smelting was essentially an activity of the Rocky Mountain area, recommended the project be, in effect, underwritten by the Fund, and the directors approved an appropriation for this purpose. Invitations were extended to high executives of the various-companies interested to send representatives to an initial meeting to be held at Salt Lake City, May 26-27. The response was enthusiastic. Twenty-three metallurgists representing 12 different plants were present to discuss the comprehensive-program relating to construction and operating phases of reverberatory smelting. It was understood that the record was not to be included in the regular publications of the Institute but that it would be prepared for private distribution among the participants and the officials of their companies. That the exchange of views and experience was no less instructive and stimulating than it was frank, full and informal is indicated by the following transcript of the minutes of the meeting.

Jan 1, 1930

J. J. MCLELLAN, Webb City, Mo.-The Media mill, at the time it was built, was the largest mill that had been designed in the Joplin district. It was put up in a hurry, to take advantage of the high prices for zinc ore in 1915, by the owners of an adjacent plant, which had been very profitable. They owned a compound Corliss engine, and to take advantage of a single-unit drive it was necessary to build the mill in the form chosen, which involved making the hopper feed directly through the breakers and rolls, the undersize from the screen passing at once to the jigs, the oversize going through the rolls and returning to the original trommels. The mill was built in fairly good proportion; crushing was done by jaw breakers, Webb City pattern,' and three sets of 42-in. (106.7-cm.) Cornish rolls for reducing the oversize. The jigs were larger than the usual practice. The roughers were two six-cell jigs, with 42 by 48-in. cells. The cleaner jig was the largest ever constructed in the district up to that time, having seven 36 by 48-in. cells, for treating the rougher jigs. There was also a chat rougher. "Smittem," as used in our district, is the partly concentrated product from the rougher, which is finished on the cleaner jigs. "Chats" are the middlings proper, that is, they are the grains of chert with included particles of sulphide; the very low-grade smittem is sometimes included among the chats. When drawing chats from a jig, we also draw about ten times greater quantity of barren chert in order to insure complete recovery of mineral. This mixture of middlings and tailings is taken to a set of 30-in. rolls, the crushed product then going to a chat rougher, a comparatively small jig, with 26 by 36-in. cells. The principal departure of the Media mill from the usual practice was to build a hopper sufficiently high to give gravity feed to the jigs, without using elevators. The sludge plant, for table treatment of sand and slime, also contained several innovations in the manner of distributing the feed. The tables were arranged in two rows and the feed ran around the outside in a launder having two or three cone classifiers

Jan 1, 1918

By L. D. Tracy

On Aug. 5 and 6,1918, and Mar. 26, 1919, the writer made an investigation of the mine-water neutralizing plant at the Calumet mine of the H. C. Frick Coke Co. The object of this plant is to develop a process of treating the water pumped from the mines so that it may be rendered suitable for use at the power plants of the mines and also at the coke ovens; at the same time, eventually producing a byproduct which will have enough commercial value to provide a sufficient revenue to place the plant on a self-sustaining basis. The Calumet mine is situated in Mt. Pleasant Township, Westmoreland County, Pa., on a branch of the southwest branch of the Pittsburgh Division of the Pennsylvania Railroad. It is about 6 mi. (9 km.) southeast of Greensburg, the county seat of Westmoreland County. The coal, which is the Pittsburg or Connellsville seam, lies at a depth of about 200 ft. (60 m.) and is brought to the surface by means of a shaft. The output of the mine averages 200,000 tons of coal annually, all of which is made into coke, either at the ovens, at the mine, or at byproduct ovens. There are 260 coke ovens at the mine. The continued development of the coal fields of Pennsylvania and the increased use of electric power in the operation of the mines has brought the problem of an increased water supply for the plants to the attention of the coal operators. This is especially true in the Connellsville coking region, where large quantities of water are used in quenching the coke at the ovens. Many of the streams receive the drainage from the mines; and as this water is highly acid and contains sulfur in various forms, some method of treatment is necessary to render it suitable for use at the plants of the mines. With this end in view, the H. C. Prick Coke Co., about 4 years ago, installed at its Calumet mine a plant for experimental purposes, in an endeavor to develop a process that would provide a maximum amount of suitable water at a minimum cost. From a purely technical point of view, the result of these experiments has been encouraging. The company is now endeavoring to place the plant on a commercial basis.

Jan 1, 1922

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Oslo, Norway. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh ..Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. '32 Abele, Louis T R.F.D. 1, Adamsville, Ohio. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius, Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service Club, 16 St. James' Sq., London, S.W. 1,, England. '28

Jan 1, 1937

By Joseph T. Singwald

INTRODUCTION THE purpose of this chapter is to present the diagnostic features (geologic, mineralogic, chemical, and physical) of the principal types of hypogene ore deposits recognized in current genetic classifications, and to classify the ore deposits of the western United States into those types. The genetic divisions used and the criteria determining them are essentially those followed by Lindgren in his Mineral Deposits. Deviations from Lindgren represent either changed conceptions since 1928 (the date of the third edition of Mineral Deposits) due to advance in knowledge or the inevitable differences of opinion between experts in active fields of investigation. Though nineteen economic geologists have been given free hand in presenting their particular topics, there are no fundamental departures in the chapter from the principles set forth by Lindgren. It would be entirely beyond the capacity of a single chapter to give a comprehensive geologic description of all the ore deposits of the western United States. Descriptions of individual deposits have been restricted to those features that are of most diagnostic genetic value. All of the more important deposits receive that much attention. Deposits of lesser economic importance and those inadequately known geologically are treated more briefly or merely cited under what seems to be their proper genetic assignment. The geographic limits of the descriptive matter are the Black Hills and the United States between the Rocky Mountains and the pacific Coast. Capacity of the chapter has made it necessary to impose these geographic limits.

Jan 1, 1933

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as fo1lows:l Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimension of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of water 1. A particle will move upward if [V > K dr(s - 1)] and, by suit- ably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [- = -] cannot be separated in an upward- current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of [2.5 - 1 2.5 sp. gr.] unless the ratio of diameters is less than [ 4.3 to 1, 1.35 – 1] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone-shaped vessels or vessels of other shapes that allow the use of different velocities of current at different points in the flow are used to modify this limitation.

Jan 1, 1943

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

Jan 3, 1953

By Marcus A. Grossman

THE institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it," All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we should review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks.

Jan 1, 1946

By F. S. White, E. L. Kinsella

THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to ' quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,1 showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.2 Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a 1/4-in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontally at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 1/2 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4 1/2-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1952

Jan 8, 1950

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906