Search Documents

By C. C. Miller, W. F. Kieschnick, E. R. Brownscombe

The possibility has been mentioned that large pressure gradients in a solution gas driven field caused by high production rates might lead to a reduction in the ultimate recovery obtainable compared to that which would be obtained by a very slow rate of production. In the present study the reservoir conditions accompanying a high rate of production and the corresponding ultimate recovery were compared with those obtained if the reservoir were produced at some marginal rate throughout its entire life. The method of calculation involved the application of fluid flow - material balance analysis to a series of successive steady state conditions in the reservoir. In the case studied very little difference in recovery was obtained at the abandonment pressure. An analysis of the basic factors involved indicates that the sane results would hold for considerable variation in properties of reservoir fluids, permeability of the formation or well spacing. Even if the reservoir has a water drive it appears that no harm will be done by- open flow production if the rate is cut back before any appreciable free gas is produced. However, any condition which leads to disproportionate withdrawal rates and which causes large pressure differences over large areas might result in substantial loss in ultimate recovery. INTRODUCTION When the pressure declines in a reservoir, gas is evolved from solution causing a shrinkage in the reservoir oil so that a stock tank barrel of oil with its residual dissolved gas occupies a smaller volume than originally. For a given reservoir oil saturation, therefore. stock tank oil content will be higher at the lower pressure. At the same time the evolved gas which remains in the reservoir reduces the reservoir oil saturation, and this would be expected perhaps to cause a reduction in stock tank oil content. However, around the well the shrinkage occurs so rapidly that stock tank oil may actually accumulate in this region in spite of the simultaneous reduction in reservoir oil saturation. If this accumulation should continue, spreading into a larger zone, the loss might be appreciable and because larger pressure gradients accompany higher rates the accumulation might possibly be large if wells are produced at too high a rate. It is the purpose of this paper to determine the effect of rate of flow on ultimate recovery by solution gas drive. The problem under consideration involves the unsteady state flow of oil in a closed radial system from which oil is produced by the evolution of gas as a finite drawdown is estalllished and the reservoir pressure declines. A somewhat similar unsteady state production problem dealing, however, with a linear system has been considered by Muskat and Meres, but these authors do not discuss the effects which rate may have on recovery. Other methods have been reported for estimaling recovery as a function of pressure decline when producing at an infinitesimal rate, and Muskat and Taylor' have shown the effect of fluid and reservoir characteristics on recovery under these conditions. Assuming steady state to exist, Babson has given a procedure for computing the decline in well productivity as the field is depleted, and Moyer has combined these methods to estimate abandonment conditions and the resulting ultimate recovery. These latter approaches to the problem either do not consider the effect of rate or assume steady state can be established. In detail this paper presents the behavior of the reservoir producing under unsteady state conditions and considers the effect of production rate during this unsteady state flow on the recovery attained. The analysis also shows that there will exist at abandonment a type of steady state, and on this basis a method has been clevelopetl for rapid calculation of abandonment conditions.

Jan 1, 1949

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By W. M. Parris, P. D. Frost, H. A. Robinson

The effects of hydrogen content and strain rate on the static tensile and notch-rupture properties of the Ti-3Mn-complex alloy heat-treated to differed strength levels were investigated. The extent of embriulement was found to be proportional to the amount of hydrogen present and the strength to which the specimens were heat-treated. The research suggests the possible necessity of specifying lower hydrogen limits than are now allowed when titanium alloys are heat-treated to higher strengths than are presently used. The research also supports a hypothesis advanced earlier for a mechanism of hydrogen embrittlement. MUCH attention has been focused on the effects of hydrogen in in Most of the published in- formation has dealt with the effects of hydrogen on alloys in the annealed or lowest-strength condition. The work of Kotfila and Erbin3 is one of the few exceptions. In view of the fact that heat-treatments are now being used to produce high strength in titanium alloys,' it is necessary that more attention be given to the effects of hydrogen on these alloys in the heat-treated condition. Research was initiated to establish the effects of hydrogen on the properties of the Ti-3Mn-complex alloy at various strength levels. This research, which supplemented that of Kotfila and Erbin, was started because it was found that high-strength tensile specimens of this alloy were strain-rate sensitive. The essential results of the research are summarized in this paper. MATERIALS AND EXPERIMENTAL PROCEDURES Material for this investigation was a 41/2-in.-diam bar forged from a single commercial heat of the Ti-3Mn-complex alloy having the composition given in Table I. The as-received forging was reduced further by forging at 1750°F to 3/4-in. square bars. About one fourth of this material was vacuum annealed at 1400°F for 24 hr to obtain a base hydrogen content of 25 ppm. The remaining bars were hydrogenated to levels of 90, 140, and 260 ppm in a large Sievert's apparatus in the following manner: Four 3/4-in. square bars, 5 in. long, were placed in the reaction chambzr. The chamber was evacuated, heated to 1400°F, and a measured amount of hydrogen was introduced. When absorbtion was complete, as indicated by the drop in pressure, the reaction tube was cooled and the bars removed. Each batch of bars was then sealed in individual evacuated Vycor containers and heated for 24 hr at 1400°F in order to distribute the hydrogen homogeneously. After vacuum-annealing or hydroge nation, the bars were rolled at a temperature (1400°F) below the ß-transus to 1/2 - in. - diam rounds. Groups of the rolled specimens representing each of the hydrogen levels were given the following heat-treatments: 1) One hr at 1300°F, water-quenched. 2) One hr at 1300°F, water-quenched, and aged 8 hr at 1100°F. 3) One hr at 1300°F, water-quenched, and aged 4 hr at 1000°F. 4) One hr at 1300°F, water-quenched, and aged 48hr at 800°F. Heat-treated bars were machined into standard 0.250-in.-diam tensile specimens having 1-in. gage lengths. Throughout the processing and testing of this material, hydrogen analyses were made by vacuum-fusion methods to check for accuracy of hydrogen additions, homogeneity, and possible losses during processing. A summary of these analyses is given in Table II It may be seen that the actual hydrogen contents were reasonably close to the desired levels. In addition, it was noted that the variation in hydrogen content within any one bar did not exceed

Jan 1, 1959

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By T. K. Perkins, O. C. Johnston

Because of the influence of dispersion on miscible-displacement processes, diffusion and dispersion phenomena in parous rocks are of current interest in the oil industry. This paper reviews and summarizes a great deal of pertinent information from the literature. Porous media (both unconsolidated packs and consolidated rocks) can be visualized as a network of flow chambers, having random size and flow conductivity, connected together by openings of smaller size. In such a porous medium, the apparent diffusion coefficient D is less than the molecular diffusion coefficient Do, as measured in the absence of a porous medium. For packs of unconsolidated granular material the ratio D/D, is about 0.6 to 0.7. For all porous rocks, both cemented and unconsolidated, the ratio of diffusion coefficients can also be represented as D/Do = 1/FF where F is the for- mation electrical resistivity' factor and 4 is the porosity. If fluids are flowing through the porous medium, dispersion may be greater than that due to diffusion alone. At moderate flow rates the porous medium will create a slightly asymmetrical mix zone (trailing edge stretched out), with the longitudinal dispersion coefficient approximately proportional to the first power of average fluid velocity (if composition is nearly equalized in pore spaces by diffusion). If the velocity in interstices is large enough, there will be insufficient time for diffusion to equalize concentration within pore spaces. In this region, longitudinal dispersion increases more rapidly than fluid velocity. At low velocities in interstices, transverse dispersion is characterized by a region in which transverse diffusion dominates. If the fluid velocity gets high enough, there will be a transition into a region where there is stream splitting with mass transfer but with insufficient residence time to completely damp-out concentration variations within pore spaces. There are several variables that must be con- trolled to get consistent longitudinal and transverse dispersion results, viz., (1) edge effect in packed tubes, (2) particle size distribution, (3) particle shape, (4) packing or permeability heterogeneities, (5) viscosity ratios, (6) gravity forces, (7) amount of turbulence, and (8) effect of an immobile phase. INTRODUCTION Diffusion and dispersion in porous rocks are of current interest to the oil industry. This interest arises because of the influence of dispersion on miscible-displacement processes. In a recovery process utilizing a zone of miscible fluid, there is the possibility of losing miscibility by dissipating the miscible fluid or by channeling or "fingering" through the miscible zone. Diffusion and dispersion are two of the mechanisms that may lead to mixing and dissipation of the slug. On the other hand, dispersion may tend to damp-out viscous fingers which may be channeling through the miscible slug. 58 Hence, dispersion may be detrimental or beneficial (if it prevents fingering through the miscible zone). Therefore, it is doubly important that we understand these processes. In this paper we review, summarize and interpret a great deal of information from the literature. In particular, we will briefly discuss molecular diffusion in miscible fluids. Then we will discuss what differences to expect for diffusion in a porous rock. If there is movement of the fluid through the rock, then there may be an additional mixing or "dispersion". Furthermore, the dispersion longitudinally (in the direction of gross fluid movement) and transverse to the direction of fluid movement will not be equal. We will discuss both types of dispersion as well as several variables which can affect dispersion (viscosity differences, density differences, turbulence, heterogeneity of media, etc.). This group of variables has sometimes led to difficulty when comparing literature data. DIFFUSION OF MISCIBLE FLUIDS If two miscible fluids are in contact, with an initially sharp interface, they will slowly diffuse into one another. As time passes, the sharp interface between the two fluids will become a diffuse

By W. Hodge, A. F. Haskins, R. M. Evans

Refractory boron compounds are shown to resist corrosion by molten zinc. Coatings were made from ferroboron and manganese boron by several methods: welding, hard facing, and pack diffusion; and techniques of coatings are very important. Mechanical failure of the diffusion coatings can be partially eliminated by applying them to type 416 chromium steels rather than carbon steels. Welded coatings made with a tungsten arc are better than those made by other welding methods. Sintered compacts of mixtures of iron and chromium borides developed strengths of about 30,000 psi. They resisted corrosion of zinc at 600°C and oxidation at higher temperatures. MOLTEN zinc rapidly attacks common metals of construction. The rate of attack is greatly amplified at temperatures over 500°C. However, there are many applications where it is necessary, or at least advantageous, to use metal construction, such as for galvanizing pots and zinc smelter equipment. Condensers and agitator linings used in continuous zinc smelting processes are eroded and corroded by violently agitated molten zinc. Pumps, tubing, and other parts to permit transfer of molten zinc would be desirable in many zinc handling operations. The development of metallic materials which are resistant to molten zinc also might permit its use as a heat-transfer medium in modern high efficiency power plants. In reviewing previous work on zinc-resistant metals, it was evident that most of the available data refer to corrosion at temperatures just above the melting point. Tungsten and high Mo-Fe alloys containing more than 80 pct Mo resist corrosion by molten zinc.', ' Imhoff states that because chromium is not attacked by zinc, chromium plating improves galvanizing pot life." Nitrided cast iron has been used in die-casting machines' where the molten alloy is 96 pct Zn and 4 pct Al. Other metals that have been suggested as of possible value for zinc resistance are columbium, tantalum, and titanium.V he corrosion of steel by zinc has been discussed by many authors,z, "2 None of these materials resisted corrosion by molten zinc at the temperatures used in this investigation, i.e., 600" to 700°C. I. Exploratory and Resistant-Coating Tests To make a study of zinc-resistant metals, exploratory tests were conducted to sort out roughly those materials which seemed most worthy of further development. This preliminary study included both solid metals and surface coatings. Exploratory Corrosion Tests in Molten Zinc—In initiating a study of this problem, numerous samples of metals and alloys were evaluated by dynamic corrosion tests made at 440 °C. Each metal was tested in its most readily available form, which, because of shape and size, was often unsuited for standard corrosion testing. The equipment used for dynamic corrosion testing of all materials, except in a few initial experiments, is shown in Fig. 1. Samples were tied to tungsten rods with tungsten wire, immersed in the zinc, and revolved at 12 rpm about the circumference of a 4 in. diam circle. Speed of travel was about 12.5 fpm. The molten zinc was protected from oxidation by an atmosphere of carbon monoxide, or, at a later period in the program, by a 9:1 mixture of nitrogen and hydrogen. When the effect of both molten metal and atmosphere was desired, the zinc level was lowered. Special high grade zinc was used in all of the corrosion tests. Corrosion losses for materials tested are shown in Tables I and 11. Whenever the materials were available in suitable form, the losses are reported in mils per year. It was recognized that weight losses on irregularly shaped specimens did not show the corrosion rate but the important consideration—poor resistance to corrosion—could be determined readily.

Jan 1, 1956

By F. A. Schaufelberger

METAL can be recovered from a leach solution either indirectly by precipitation as a compound that is later reduced or directly by electrolysis, cementation, or chemical reduction, for example, with hydrogen. The widely used electrowinning processes suffer from the inefficiency of converting fuel to low voltage dc and from low current efficiency when complete recovery is attempted. With the batch hydrogen reduction methods outlined here, a unit of fuel converted to hydrogen in modern gas reform plants will make two to three times as much metal as can be obtained with electrolysis. With continuous hydrogen reduction, four to six times as much metal is obtained. Precipitation by reducing a metal salt solution with H, has been known for almost 100 years.' Commercial use of the process, however, awaited the research and development program initiated by Chemical Construction Corp. Within the last few years this program has brought about construction of commercial plants, listed on page 545. Ideal hydrogen reduction will precipitate a pure metal from a solution obtained by commercial leaching methods at a rapid rate without excessive temperatures and pressures. The metal precipitate will be of desired size and density, less than a percent left in the vessel being deposited on the wetted parts. The present discussion will outline Chemical Construction Corp.'s early development program and will discuss the chemistry and mechanics of reducing copper, nickel, cobalt, and cadmium from solution by H2. Work on selective reduction of nickel from cobalt has been described earlier.' The article is not concerned with precipitation of copper by disproportionation of cuprous solutions where yield is limited3 to 50 pet.* It does not discuss use of gaseous reducing agents other than hydrogen, such as SO2,4 which may lead to contamination with sulfur, or C0,5 which is considerably more expensive than hydrogen and produces a gaseous reaction product, CO2.† The article does not include use of other nongaseous reducing agents,7 which are far more expensive than CO. Also, notes on the history, engineering design, and performance of commercial plants have been given elsewhere.' It will be shown that a pure metal can be precipitated by reduction with hydrogen from solutions obtained by commercial leaching methods when the solution composition is controlled and proper acidity, proper metal ion concentration through controlled complex formation and hydrolysis, and adequate agitation for suspension of metal and for transfer of reducing gas are maintained. Reasonable temperatures and pressures are used which are less excessive than those used by previous workers, although they are maintained at above equilibrium values because of process kinetics.' It has also been found necessary to induce nuclea-tion and to control growth and agglomeration in order to get a powder product of suitable physical properties. Review of the Literature Muller, Schlecht, and Schubardt of I. G. Farben10 claimed a successive reduction of silver, copper, nickel, cobalt, and zinc from ammoniacal solution by applying progressively higher temperatures and hydrogen pressures. Metals produced by this technique were not pure, since no attempt was made to adjust the solution composition between the different reductions. It is doubtful that the zinc product contained any metallic zinc. The major contribution to the literature" was made by the Ipatiews,12 who prepared platinum, iridium, copper, nickel, cobalt, lead, tin, arsenic, antimony, and bismuth at often extreme conditions, up to the critical temperature of water (373ºC), at 1500 to 7500 psi, for as long as several days. Even cadmium and zinc were claimed to have been observed in trace quantities precipitated together with basic salts. In the early experiments solutions were not stirred. Extensive formation of oxides and basic salts occurred, probably long before sufficient hydrogen could be supplied in the unstirred liquid to decrease the metal concentration in solution by reduction. The importance of hydrogen pressure was

Jan 1, 1957

By G. H. Kesler, C. E. Dryden, J. H. Oxley

Rates of heat- and mass-transfer from rods to recirculating air were determined within a one-quarter-scale model of a metals deposition bulb. The dependence of local and averaged rates of transfer upon outlet geometry, number of rods, position upon a rod, and airflow rate was established for flow patterns created by radial and tangential air inlets. The results are given a qualitative interpretation in terms of rates and distribution of metal deposition in a prototype deposition bulb. IT is well known that a number of metals can be prepared from volatile compounds containing them by causing dissociation of their compounds to occur at heated surfaces. Examples of such metals include silicon, titanium, zirconium, and aluminum, which can be prepared from their halides. While the ability to prepare high-purity metals by this technique is of importance in itself, the rate of deposition of metal also is important in considering the commercial potential of such a process. If the over-all process of deposition is broken down into separate steps of transport of materials to and from the heated deposition surface and establishment of chemical equilibrium at the surface, as was described in a recent paper,1 then since surface temperatures are usually high and surface equilibrium is attained very rapidly, the rate-controlling step can be considered as either that of transport of reactants to the surface or of transport of products other than deposited metal away from the surface. These two transport steps are related through the reaction stoichiometry. It can be shown1 that the rate and distribution of metal in such a transport-controlled process are determined by the over-all and local mass-transfer coefficients in conjunction with the equilibrium conversions at the hot surfaces. The rate relationship is: w = [KA(y a-y s)] B.E where the bracketed group is the rate of arrival of the reactant at the surface of area A as determined by the mole fraction driving force (y a - y s) and the convective transport constant K. The factor B is the weight fraction of metal in the reactant, and E is the equilibrium fractional conversion to metal. Numerical values of y, and y, are fixed by the vapor composition and the equilibrium compositim of reactant at the surface; and E can be determined by thermodynamic calculations or by experiment. However, values for the convective coefficient K are available generally only for systems of simple geometry, such as cross-flow past a rod or sphere or parallel flow past a flat plate or through a tube. Often it is necessary to work with systems of more complex geometry and in which the vapor flow may not be uniform or exactly parallel or perpendicular to the surface. It is possible, of course, to establish working correlations for these more complex systems by direct experiment; but the experiments usually are costly in both time and money. To circumvent this objection and to aid in arriving at an understanding of the relationships and interactions of the process variables, it is helpful to construct a model of the flow system in which air, water, or other convenient fluids can be substituted for the process vapors and with which mass-transfer measurements or analogous he at-transfer measurements can be made upon a simulated deposition surface. By this means, a large number of measurements can be made in a reasonable time, and the correlation of these results can be applied to the prototype system. Examples of the application of these techniques are to be found in the literature (e.g., Ref. 2). It is the purpose of this paper to illustrate these techniques by description of a model study which was done at Battelle Memorial Institute. The work to be described was of a preliminary nature; the investigation subsequently was extended to develop quantitative relationships among the significant dimensionless transport, geometric, and flow parameters. This more detailed study will be the subject of a future paper.

Jan 1, 1962

By K. Takahashi, I. Iwasaki

The methyl stretching vibrations for a series of normal xanthates, isoxanthates and normal amines were determined with the aid of an infrared spectro-photometer, and the results were compared with published information on the corresponding alcohols. The frequency shifts of methyl stretching vibrations may be attributed to the inductive effect of polar groups. The hydrogens in the shorter chain alkyl groups are somewhat polar and can be expected to interact with water molecules by hydrogen bonding. Contact angle, surface tension lowering, solubility, and critical micelle concentration appear to be related to the induced polarity of the alkyl groups. Traube's rule states that in homologous series of compounds solubility decreases and surface activity increases regularly with the size of the hydrocarbon group. Analyzing the work of transfer of a solute from solution to surface, Langmuir' interpreted this rule to mean that each CH2 group added to a molecule produced its effect independently of the others. It is also well known2 that the maximum equilibrium contact angle with sulfhydryl collectors is independent of the polar groups and of the sulfide minerals, and that it increases to a certain limit with the number of carbon atoms in the alkyl group. This observation is thought to demonstrate the orientation of the collector molecules at the sulfide surfaces. The dependence on the hydrocarbon chain length is usually explained as due to the screening of the force field of polar mineral surfaces.3-5 Here again, Langmuir's principle of independent surface action appears to be implied. Heteropolar compounds consist of nonpolar and polar groups, the former being the hydrocarbon group and the latter containing such electronegative atoms as O, N, S, P, or halogens. According to Palit6 the hydrogens in the alkyl groups are more electroposi- tive than in the paraffins owing to the negative inductive effect of the polar groups and a possibility that a hydrogen bond with water molecules ensues. Goto and Takenaka7 provided direct evidence of the inductive effect by measuring the shift of the C-H stretching vibrations of alcohols, acids, and alkyl bromides with an infrared spectrophotometer. Their approach appeared to be directly applicable to the studies of surface activity both at air-water and water-mineral interfaces encountered in flotation systems. The present article attempts to relate the C-H stretching vibrations of alkyl xanthates, alcohols, and amines with such flotation chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration. MATERIALS AND METHODS Normal xanthates from methyl to octyl inclusive and the isopropyl, isobutyl, and isoamyl xanthates used in this investigation were prepared in the usual manner.8 Normal amine hydrochlorides with carbon chain lengths of 1, 2, 4, and 6 were from Distillation Products Industries, of 8 from Archer-Daniels-Midland Co., and of 10, 12, 14 and 16 from Armour and Co. Normal propylamines, pentylamines and heptylamines from Distillation Products Industries were used both as received and as hydrochloride formed by converting the amines according to the procedure described by Li9 Perkin-Elmer Model 521 and 621 infrared spectro-photometers were used to investigate the spectra in the frequency region of 3050 to 2800 cm-' with frequency scale expansion. The accuracy of the frequency readings was within + 1 cm-1. The KBr micropellet technique was used to prepare the xan-thate samples for measurements, and the halocarbon mull technique was used for amines and amine hydrochlorides. EXPERIMENTAL RESULTS Fig. 1 shows the CH3 asymmetric stretching vibrations as a function of the number of carbons in the alkyl group for normal xanthates, isoxanthates and amines. Also included in the figure are data for normal alcohols and isoalcohols taken from the article

Jan 1, 1970

By Franklin J. Hill, Theodore D. Tiemann

Sized fractions of Wisconsin Gogebic taconite were reduced with hydrogen over the temperature range from 600° to 1000°C. In general, the degree and rate of reduction increase with temperature. Particle size has no observable effect except in the smaller fractions at 900°C and above, where reduction is impeded, possibly due to the siliceous nature of the ore. Gaseous diffusion appears to be significant as a rate controlling factor at certain stages. THE depletion of high grade iron ore reserves in the United States has established the need to utilize all available iron ore deposits, both in long range planning and from the viewpoint of national emergency. This has led to extensive research and development in this field. The beneficiation of Wisconsin Gogebic taconite ore has been previously studied by investigators at the University of Wiscconsin, 1 the United States Bureau of Mines,, Battelle Memorial Institute, 3 and others. Methods investigated have included concentration by flotation processes, magnetic and gravity separation, magnetic roasting and various combinations of them. The foregoing studies have been concerned with the production of an enriched ore suitable for blast furnace use. If the ore could first be reduced to metallic iron and then beneficiated, the product could be used directly in the open hearth or electric steel-making furnace. The by-passing of the blast furnace should enhance the economic feasibility of the beneficiating process. The work reported here,4 was undertaken to establish data on the hydrogen reduction of Wisconsin taconite that would eventually lead to the development of an economic direct reduction process for this and perhaps other low grade siliceous ores. The volume of work on direct reduction can be judged by the fact that 240 direct reduction processes were patented in the United States alone up to 1951, 5 and numerous additional processes have since been developed. Some of the factors contributing to direct reduction development are: 1) The increasing capital cost of the blast furnace and its accessory equipment. 2) The decreasing availability of high grade domestic ore. 3) The high cost of steel scrap for use in the open hearth and electric furnaces. In general, direct reduction processes can be divided into two types; those using a solid reductant (coal, peat, lignite) usually carried out in a kiln, and those using a gaseous reductant (H2, CO) in a shaft furnace or a fluidized bed retort. As there is no low cost coal readily available in northern Wisconsin but natural gas could be quite easily obtained, it is believed a gaseous reductant process would offer the greater feasibility for use on Wisconsin taconite. It is hoped that this preliminary work will beof interest to other investigators in this increasingly important field. TACONITE ORE The ore used in the investigation was obtained originally from the U. S. Bureau of Mines, and consisted of a representative composite made up from trench samples of the Norrie, Pabst, Plymouth, Pence, and Yale members of the Wisconsin Gogebic range iron formation. Chemically, the ore contains approximately 52 pct SiO, and 30 pct Fe. X-ray diffraction and other studies indicate the principal minerals to be quartz (SiO2), hematite (Fe2O3), and goethite (Fe2O3. H2O). Minor amounts of iron containing silicates, siderite (FecO3), and magnetite (FeO-Fe2O3) are present. The iron minerals and quartz are so finely disseminated that the ore requires grinding to less than 200 mesh (74 µ) for essential liberation.l,2 The iron content of each of the several size fractions studied is shown in Table I. EXPERIMENTAL METHOD The method used throughout the investigation was based on that developed by the U. S. Bureau of Mines in Minneaopolis6,7 in which the course of reduction is followed by the loss in weight of the ore sample. More specifically, a 100-g sample of the size frac-

Jan 1, 1962

By Charles Stein

The effects of several different prior treatments an the creep behavior of 99.9995 pct aluminum at 260°C and 1000 psi canstant stress are compared with annealed specimens. Quenching from 538oC, irradiation with 2 mev electrons, and tension-compression room temperature fatigue damage were used to change the substructure of the specimens prior to their creep testing. The quenched and the irradiated specimens showed a larger primary and transient stage contribution to the creep curve than those specimens which were only annealed prim to creep testing. The specimen receiving prior fatigue damage at room temperature showed no first stage or transient creep when tested under identical conditions as the above specimens and had an average creep rate seven orders of magnitude lower than that of either the annealed, the quenched or the irradiated creep specimens. In a previous electron transmission microscopy investigationl of the substructure developed during the creep of pure aluminum at 0.57 Tm, it was noted that a large concentration of vacancy loops and dislocation loops were present in and near the subboundaries while the interior of the subgrains contained few of these defects and had a low dislocation density, see Fig. 1. Yim and Grant2 and Hazlett3 have shown that the presence in nickel of a substructure developed by prior cold work effectively reduces the primary and transient contributions to the creep curve. Hultgren,4 McLean,5 Gervais, Norton, and Grant,6 Chang and Grant,7 and others have shown the same effect with the higher stacking fault energy material, aluminum. However, the specific defect responsible for the change in the creep behavior developed by the prior cold work was not established. Specifically, what effectively interfered with dislocation motion in these materials at elevated temperatures? Was it jogs on dislocations produced by their interaction with other dislocations or with vacancy or dipole loops, see Fig. 1, or did the subgrain walls determine the mean free path for glissile dislocations? This would be a realistic possibility only if subgrain boundaries are effective barriers to dislocation motion. The ability of a subgrain boundary to act effectively against glissile dislocations depends on the number and the arrangement of dislocations in the subboundary,8 which in turn is a function of the creep strain.' This paper compares the creep rate of specimens possessing a large vacancy concentration to that of annealed specimens and with specimens having a stable subboundary wall containing Lomer locks produced by prior fatigue damage. EXPERIMENTAL PROCEDURE Vacancy Loops. Aluminum creep specimens, 99.9995 pct pure, were machined from zone refined rod to a 2-in. gage length and a cross-sectional area of 0.025 in. These specimens were annealed at 538oC, 1000°F, for 10 min and quenched into ice water. They were then reheated to the creep test temperature of 260°C, 500°F, and held at this temperature for 18 min to al-low for vacancy condensation and loop formation. The specimens were subsequently creep tested at 1000 psi constant stress at 260°C. The temperature along the gage length was monitored by three Pt-Pt, 13 pct Rh thermocouples, two embedded in the upper and lower shoulders of the specimen and one attached to the mid-point of the gage length- The temperature gradient was held to ± l°C or less throughout the Creep test. Elongations were measured by two LVDT's 'connected in an averaging 'On-figuration, with quartz extension arms placed against the specimen at the extremes of the 2-in. gage length. i K 3J?--' * *H - >^> - ' ^L r 77 . *y J OJL, J Fig. 1—Transmission electron micrograph of pure aluminum strained 8.2 pct at 260°C and 1000 psi constant stress. Note the presence of numerous loops near the light dislocation tangle

Jan 1, 1970

By E. A. Gulbransen, A. Pebler

Pressure-composition isotherms have been determinedfor the systems ZrMo2 -H2 between 0" and 900°C at hydrogen pressures between 10-4 and 760 Torr. Tkese studies plus X-ray diffraction analyses of selected compositions show that these intermetallic compounds form a complete series of hydrogen solid solutions within this temperature and pressure range. The partial molar enthalpies and entropies of solution of hydrogen in the three intermetallic compounds were calculated. The solubility of hydrogen in these Laves phases can be related to their free electron concentration. ThE reaction of hydrogen with inter metallic compounds of zirconium with Laves phase-type structure has both theoretical and practical interest. The in-termetallic compounds have structures different from any of the pure metals. In addition the electron to atom ratio of the intermetallics varies appreciably. In the nuclear materials field, these materials are of interest since intermetallic compounds may exist as precipitates in commercial zirconium alloys with transition metals. From studies on the hydrogen reaction, one can establish the stability of the intermetallic compounds relative to the hydrides of the component metals. The intermetallic compounds may also be used as getters for hydrogen and as materials for hydrogen storage. This paper will present the results of equilibrium and structural investigations of the ZrCr2-H2, the ZrV2-H2, and the ZrMo2-H2 systems for the temperature range of 0" to 900°C and the pressure range of Torr to 1 atm. A complete thermochemical analysis will be made of the measurements. Some of the results have been referred to in a survey paper' covering the types of hydrogen behavior observed in zirconium alloys. LITERATURE ZrCr2 is the only intermetallic phase in the Zr-Cr system.' It exists in two allotropic modifications. Between 900" and 1000°C the hexagonal MgZa (C14) structure transforms into the cubic MgCu2 (C15) structure. Beck4 has previously shown that the intermetallic ZrCrz takes up hydrogen into solid solution up to a composition H/ZrCr2 = 1.14 at room temperature and 1 atm hydrogen. A ZrCr2 hydride was stated to have a fcc structure. The binary Zr-V system has been investigated by williams5 although Rostoker and Yamamoto 6 had given earlier a partial phase diagram. ZrV2 was the only intermediate phase found in the system. wallbaum7 reported earlier that the compound ZrV2 hp the MgZm (CJ4) type structure with a = 5.288A and c = 8.664A. This was not comfirmed by Elliot8 nor by Matthias, Compton, and corenzwit9 who reported that ZrV2 has a cubic MgCua LC15) type structure. The latter authors gave a = 7.429A. Also, several authors do not agree on the temperature of the peri-tectic horizontal. It appears that ZrV2 may exist in several modifications. A high capacity for occluding hydrogen was reported by Beck4 who found H/ZrV2 = 1.38 at room temperature and 1 atm of hydrogen. ZrMoz is the only intermetallic phase in the Zr-Mo system.10 ZrMoa is formed by a peritectic reaction of the melt with a molybdenum-rich solid solution. ZrMo2 has the C15-type structure with a = 7.59A. MATERIALS High-purity chromium, vanadium, and molybdenum were used together with grade 1 crystal bar zirconium to prepare the alloys. Table I lists the chemical analysis and the sources for the metals. Ten-gram alloy compacts were levitated and melted in an inert argon

Jan 1, 1968

By G. Derge, Ling Yang, John Henderson

Self-diffusion coefficients of aluminum have been measured by the capillary reservoir technique in liquids of the CaO-SiO2-Al2O3 system containirg equimolar portions of CaO and SiO2, in the temperature range 1400o to 1520oC. For the melt containing 6.0 mole pct Al2O3 the results can be expressed by the equation D = [(4.3 * 0.3) x 104] exp [(-85,000 * 17,500)/RT]cm~sec-'; for the melt containing 12.5 mole pct Al2O3, by the equation D = (5.4 i 0.2) exp [(-60,000 * 10,00O)/RT] cm2sec-: A concept of the constitution of these melts has been developed which proposes that the ratios O/(Si +Al) and Al2 O3/CaO determine the dominant species present. In recent years considerable work has been done on the system CaO-SiO2-A12O3 with a view to elucidating the structure of liquids of this system. Conductivity,' electromotive force, 3 density,4 and activity5 measurements have all contributed to an understanding of the problem, but as yet there is no entirely satisfactory theory that can account for all the observed experimental results. In principle, measurements of self-diffusion coefficients should give further information which is not obtainable in other ways. Self-diffusion coefficients for calcium, silicon,6 and oxygen7 have been measured. The present investigation extends the series of self-diffusion coefficient measurements to include aluminum and develops a concept of constitution for liquids of this system which is compatible with all the observed experimental results. EXPERIMENTAL The technique used in the measurement of the self-diffusion coefficient of aluminum was the capillary-reservoir method,8 A126 being incorporated in the melt contained in the capillary and inactive aluminum in the reservoir melt. This method was chosen because it minimizes convection currents' in the diffusion zone. It has the further advantage that the boundary conditions are such that a slight modifica- tion of Anderson and saddington's8 solution of Fick's Law yields an equation which requires measurements only of the length and the initial and final average specific activities of the solidified melt within the capillary. where t is the diffusion time, Co is the average specific activity of the melt contained in the capillary at t = O, C is the average specific activity of the melt contained in the capillary at t = t, 1is the length of the capillary, and D is the self-diffusion coefficient. The equation is of somewhat different form than those previously applied to high temperature diffusion studies because the specific activity of the melt in the reservoir was negligible both before and after diffusion. The diffusion apparatus is shown schematically in Fig. 1. It consisted of a silicon carbide resistance furnace containing the inactive melt in a graphite crucible, internal dimensions 7/8 by 4 in., enclosed in a 1 1/4- by 1 1/2- by 30-in. McDanel tube. A 3/8-in. McDanel thermocouple sheath to which graphite radiation shields and a graphite protection tube were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube the capillaries could be lowered into or raised out of the melt. Temperature was measured with a Pt-Pt 13 pct Rh thermocouple which was calibrated periodically against a standard couple. The furnace temperature was controlled to ± 5°C through the thermocouple immersed in the melt. Temperature variation over the depth of the melt was less than ± 3°C. The inactive melts were prepared from pure native quartz, assaying better than 99.9 pct SiO2, A.R. grade A12O3 and A.R. grade CaCO,. The same quartz and CaCO3 were used in preparing the active melts, the

Jan 1, 1962

By M. R. Tek, F. F. Craig, J. O. Wilkes, C. S. Goddin

The waterflood performance of a water-wet, stratified system with crossflow is computed by a finite difference procedure. The effects of five dimensionless parameters on tile oil displacement efficiency, water saturation con-tour.7 and crossflow rates are evaluated in the absence of gravity forces. Crossflow due to viscous and capillary forces is shown to exert a significant effect on oil recovery in a field-scale model of a two-layered. water-wet sandstone reservoir. The crossflow is at a maximum in the vicinity of the front advancing in the more permeable layer. Under favorable mobility ratio conditions, the comparted oil recovery with crossflow always is interrnerliate between that predicted for a uniform reservoir and that for a layered reservoir with no crossflow. INTRODUCTION The important erects of reservoir heterogeneity on waterflood performance are commanding increased attention in the technical literature. Much of this attention is centered on two categories of layered reservoirs: those in which layers are non-communicating and those in which crossflow of fluids occurs between the layers. In the first category, the reservoir is assumed to consist of discrete layers, each uniform within itself and differing from the others only in such properties as thickness, porosity and absolute permeability. The performance within each layer is calculated by one-dimensional flow theory, and the performance of the total reservoir is obtained by summing individual layer performances. Capillary and gravity effects usually are not considered. Representative publications dealing with thi5 type of reservoir are those of Stiles,' Dykstra and Parsons,' Hiatt,3 Warren and Cosgrove' and Higgins and Leighton." Prediction of performance for reservoirs in the second category is considerably more difficult since viscous, capillary and gravitational forces all play important roles in causing crossflow between layers. A number of authors have investigated the simpler problem of two-dimensional displacement flow in a stratified system with a mobility ratio of unity and negligible capillary and gravity effects.'; Others have considered two-dimensional, non-steady-state flow of a single, slightly compressible fluid in a stratified reservoir. A limited number of laboratory oil displacement tests in layered models with crossflow have been reported. Miscible floods (with resultant zero capillary forces) in layered five-spot models were conducted by Dyes and Braun," who studied the effect of mobility ratio with zero gravity forces, and by Craig et al. 12 who studied the effect of gravity forces at constant mobility ratio. Waterfloods in layered five-spot models (with cross-tlow due to capillary, viscous and gravity forces) were conducted by Gaucher and Lindley,"' who showed the effect of gravity forces in causing underrunning of the injected water and by Carpenter, Bail and Bobek, 14 who demonstrated the reliability of Rapoport's" dimension-less parameters for scaling layered systems. Waterfloods in rectangular layered models were conducted by Richardson and Perkins."' who investigated the effect of velocity at constant mobility ratio and with zero gravity forces, and by Hutchinson," who studied the effects of varying mobility, layer permeability and layer thickness ratios. The differential equations which rigorously describe waterflooding in a heterogenous porous medium are non-linear and do not facilitate analytical solution. By using finite difference approximations it is possible to obtain a solution to any desired degree of accuracy. Such a solution, using an alternating direction implicit procedure (ADJP), is described by Douglas, Peaceman and Rachford.18 In the present study, a computer program using ADJP explores systematically the effects of important parameters on waterflood performance of a two-dimensional, two-layered, field-scale model of a water-wet sandstone system. Particular attention is given to evaluation of the water saturation contours and crossflow rates at the interface between layers to gain improved understanding of the crossflow mechanism. PROCEDURE BASIC: FLOW EQUATIONS The basic flow equations for two-dimensional, two-phase, immiscible, incon~pressible flow in a porous medium are:

Jan 1, 1967

By L. L. Handy

The most common method of identifying hydrocarbon-bearing strata in a well that penetrates many different formations involves measurement and interpretation of the electrical properties of the formations as determined by electrical logs. Even though this method is used extensively, and even though in a great many instances it is capable of indicating presence of oil or gas, situations arise for which it is extremely difficult, if not impossible, to deduce the presence of hydrocarbons. These situations may involve the following. 1. A thin formation, bounded by highly resistive formations, in which it is impossible to obtain the actual resistivity of the uninvaded zone with existing logging devices. 2. A formation in which invasion has been so extensive that a value for the uninvaded zone resistivity cannot be obtained. 3. A very shaly formation in which the resistivity index, I, is lower than that usually associated with productive formations. 4. Laminated formations comprised of thin productive sands separated by thin shale streaks in which the individual sand and shale streaks are too thin to permit measurement of uninvaded-zone resistivity with existing logging devices. 5. Productive formations in which the water saturation is high. To extend the utility of electric log interpretation to identification of hydrocarbons in all types of formations, there is strong incentive to find a method not subject to these limitations. Some time ago, in connection with research on the wettability of reservoir rock, an investigation was conducted in which the resistivities of cores were measured shortly after they were removed from a core barrel, and again after they had been extracted and restored to their original oil and brine saturation.' The resistivities after extraction were generally lower. Other tests made on the cores indicated that they were more nearly water wet after they were extracted; thus, it was assumed that the observed changes in resistivities were due to a change in wettability of the cores. Other experiments'," have shown that resistivities of rock samples are sharply dependent on wettability. These experiments have shown that oil-wet samples are more resistive than water-wet samples. To obtain an understanding of how the wetting properties of the surfaces of core material affect electrical resistivity, a series of experiments was conducted. Two groups of core samples were prepared for testing. One group contained brine, but no residual oil. The other group was saturated with brine, flooded with oil to a low water saturation, then flooded with brine to a final residual oil saturation. Resistivity measurements were made on each group. Both groups were then flooded with the original brine to which a chemical had been added that renders sand and clay surfaces preferentially oil wet, a so-called reverse-wetting agent. very little change in resistivity was observed in cores containing only water. The group containing residual oil, however, showed resistivity increases of 100 to 200 per cent. These experiments showed that the resistivity of a core containing oil could be altered by changing wet-tability of the core. Moreover, the possibility was introduced that reverse-wetting agents might be employed as the basis for a logging method for identification of oil-bearing strata. Since behavior of a porous rock containing gas and water might be expected to be similar to that of a rock containing oil and water, such a method should also be applicable to identification of gas-bearing zones. In principle the wettability of the invaded zone could be reversed without altering conductivity of the interstitial water or the hydrocarbon saturation therein. Those strata showing significantly increased invaded-zone resistivities would, therefore, contain hydrocarbons; those with no significant change would be filled only with water. Addition of a reverse-wetting agent to a hydro carbon -bearing zone which is, by nature, already preferentially oil wet would not result in an enhancement of its resistivity. It is generally believed, however, that most hydrocarbon-bearing strata are preferentially water wet.

By C. H. Li, R. J. Stokes, T. L. Johnston

The phenomenon of solid-solution strengthening has previously been studied in a number of binary alloy systems.1-8 There has been, however, very little information published concerning the strengthening effects of specific solutes in magnesium alloys. Schmid and his coworkers9,10 investigated the behavior of aluminum and zinc in binary and ternary magnesium-alloy single crystals, but this work was done before high-purity materials were readily available. Workers at the Dow Chemical companyH reported increases in the critical resolved shear stress upon alloying magnesium single crystals with zinc and indium. Recently, Hardie and parkins* investigated the extent of hardening produced by the addition of various solutes to poly crystalline magnesium. The present work was undertaken to provide data on the strengthening effects of a number of solutes in high-purity magnesium, for the purpose of supplying further experimental information which might be useful in describing a general mechanism for solid-solution strengthening. To simplify interpretation of the results, the mode of deformation was limited to basal slip, through the use of single crystals. EXPERIMENTAL PROCEDURE Magnesium and magnesium binary-alloy single crystals containing indium, cadmium, thallium, aluminum, and zinc were prepared in the form of l/2-in.-diam rods, approximately 8 in. long, using a modified Bridgman technique in which the crystals were slowly cooled from the melt in a steep temperature gradient, in an atmosphere of helium. It was found that a solid-liquid interface travel speed of about 0.7 in. per hr consistently produced single crystals. The poly crystalline starting materials for the preparation of single crystals consisted of 1/2-in.-diam extruded rods, prealloyed to the desired composition. The unalloyed magnesium and magnesium-indium extrusions were furnished by the Dow Chemical Co. The other alloys were prepared at the Rensselaer Polytechnic Institute Metallurgical Laboratories. Some preliminary studies of the strengthening effect of indium were conducted at room temperature using a constant rate of tensile loading of 1040 g per min. Stress was applied to the crystals by means of a simple 5:l lever arm. The lever was loaded by a constant rate of flow of shot into a receptacle suspended from the long arm of the lever. Plastic flow was detected by an electrical resistance strain gage cemented to the surface of the crystal normal to the minor axis of the predicted glide ellipse. The crystals were acid machined to produce tensile specimens with a reduced section between the grip ends, with an additional step in the center of the reduced section to compensate approximately for the slip-retarding effect of the strain gage. The balance of the single crystals were extended in an Instron tensile tester. This machine employs a synchronously driven screw and automatically records applied load as a function of cross-head separation. It became unnecessary therefore, to employ a strain gage to detect deformation or to acid machine a reduced section. Preparation for testing reduced merely to chemical cleaning of the surface, thus minimizing the amount of handling and probability of accidental damage to the crystals. The rate of elongation employed in all the tests was 0.002 in. per min, corresponding to a strain rate of approximately 0.0004 per min. EXPERIMENTAL RESULTS The investigation confirmed the finding of many workers that the yield strength of hexagonal metal crystals is strongly orientation-dependent. This is illustrated in Fig. 1, in which o, the tensile stress required to produce gross plastic flow in eleven unalloyed magnesium crystals stressed at a constant rate of loading is plotted as a function of sin X, cos Ao where X, is the angle between the

Jan 1, 1960

By R. H. Oliver

The purposes, types, preparation, and testing of flocculants are discussed. A flocculation compendium is included, indicating choice of flocculant for a given set of conditions. An economic evaluation of the process is presented. Solid-liquid separation is a major expense in most mineral processing flowsheets today. Proper use of flocculation can often lower the overall cost of a solid-liquid separation by reducing the size of sedimentation or filtration equipment. PURPOSE OF FLOCCULATION When is use of a flocculant justified in terms of overall process economy? 1) when it results in process improvement, such as producing a clear liquor for electrolysis, precipitation, ion exchange, or solvent extraction; 2) when it results in satisfying requirements of pollution abatement ordinances; 3) when it results in increased recovery of values that would otherwise be lost; or 4) when it results in considerable savings in capital expenditure due to use of smaller equipment. When can the use of a flocculant adversely effect overall process economy? 1) when it results in increased filter cake moisture, 2) when it results in decreased filtration rates, 3) when it results in considerable bulking of sedimentation underflow, 4) when it contaminates either the supernatant or sludge, or 5) when the cost of using the flocculant is greater than the savings due to its use. First step in consideration of flocculants for a given application is establishment of desired goals in terms of increased clarity of effluent, increased recovery of solids, or decreased size of equipment. The most economical solution to a solid-liquid separation problem is that combination of equipment and flocculant costs which meets the established goals at the lowest total annual expenditure. This economic decision can be made only after technical data has been obtained as outlined in next four sections. TYPES OF FLOCCULATION Flocculation is a process wherein individual particles are united into more or less tightly bound agglomerates or flocs, thereby increasing effective particle size of solids suspended in a liquid. Degree of flocculation of a suspension of finely divided solids in a liquid is controlled by a combination of probability of collision between particles and probability of adhesion after the collision has occurred.' Probability of collision can be increased commercially through use of a paddle-type flocculator, combination flocculator, and clarifier or flocculating-type feedwell. Probability of adhesion usually can be increased by addition of a reagent known as a flocculant. Reagents act as flocculants through one or a combination of three possible mechanisms. The first is electrolytic neutralization of inter molecular repulsive force due to Zeta potential. This neutralization enables Van der Waal's cohesive force to hold the particles together after they collide.' The second is the precipitation, within a definite pH range, of voluminous metallic hydroxide flocs which entrap fine particles. This process is known as coagulation.14 Third is the bridging of two or more particles by either natural or synthetic long-chain, high-molecular-weight organic polymers. This bridging is accomplished by adsorption of two particles at different sites on the same molecule or by bonding of two molecules, each adsorbed to a different particle. Considerable effort has been expended in explaining the action of these polyelec-trolytes and detailed accounts are available in the literature. CHOICE OF FLOCCULANTS It is impossible, at the present time, to specify the optimum type or amount of flocculant for a given application from a knowledge of the material to be treated. The standard procedure is to choose reagents or combination of reagents most likely to be effective on the slurry; then test them.' The accompanying Flocculation Compendium (Table I) contains details of all currently available reagents sold as flocculants and it should be used when selecting the group of reagents for tests. This selection can be based on information listed in columns 4 and 5. Column 4 presents industries in which each floc-

Jan 1, 1961

By E. L. Claridge, K. S. Lee

Areal sweep efficiency of oil displacement by enhanced-viscosity water exhibiting pseudoplastic behavior was measured in a Hele-Shaw model representing one-quarter of a five-spot pattern. The pseudoplasticity of polymer solutions and the velocity distribution in the five-spot pattern produced a condition under which the mobility ratio between the displacing and the displaced fluid could not be assigned a single value. Instead, the movement of the displacement front is governed by local mobility ratios which are also time dependent. The areal sweep at breakthrough with polymer solutions was poorer than the sweep obtained with Newtonian fluids of comparable viscosity. However, the areal sweep at 1 PV throughput was greatly improved as compared to flood water without polymer. It was also demonstrated that, even after the oil-cut had declined to a low value during a regular waterflood, switching to polymer flood efficiently swept out the oil remaining in the model. INTRODUCTION The behavior of fluid displacements in isotropic porous media for various patterns of injection and production wells has been extensively investigated.1-7 These investigations all concerned Newtonian fluids, i.e., the viscosity of each fluid was constant regardless of flow rate. The generally unfavorable influence on areal sweep efficiency of higher mobility of the displacing fluid as compared to the mobility of the displaced fluid has been established for both miscible and immiscible fluids. The principle was also established that a close correspondence exists between miscible and immiscible flood front behavior,2, 3 although oil recovery in a waterflood at unfavorable mobility ratio may be less than that observed in a miscible displacement at the same mobility ratio. This is true even when oil recovery is expressed on the basis of movable oil. The reason is that oil saturation only slowly achieves its final value behind the water-flood front in accordance with the Buckley-Leverett8 simultaneous flow relations. It is convenient to use miscible displacements for laboratory simulation of waterflood frontal advance since the interfacial tension forces which are negligible in proportion to viscous forces on a reservoir scale9 are thus made nonoperative in the laboratory model. For miscible displacements, the Hele-Shaw type of model adequately represents a porous medium so long as the appropriate scaling rules5-10 are observed in its design and operation. During simulation of waterflood front behavior in the laboratory by using miscible displacements, the behavior of connate water may ordinarily be disregarded since it is usually indistinguishable from flood water in this process. However, when the flood water is deliberately thickened to improve the mobility ratio between water and oil. the effect on the sweep efficiency due to generation of a connate water bank during the process must be considered. In a uniform porous medium, such a bank is generated11 and efficiently displaced by injection of thickened water.l2 The oil originally in-place at the start of the waterflood is then displaced by connate water followed by thickened water. If the flood water must be thickened to obtain a favorable mobility ratio, the mobility of the oil phase is appreciably less than that of the connate water. Hence, the oil phase is inefficiently displaced by the connate water bank, and a considerable proportion of the oil comes in contact with and is displaced by the thickened waterflood front' A recent study 12 of five-spot displacements using miscible Newtonian fluids in which connate water banks of various sizes were simulated shows that, for connate water banks as large as 40 percent of 1 PV, major improvements in sweep efficiency resulted from use of a thickened

Jan 1, 1969

By H. J. Ramey

A general solution is presented for the transient temperature distribution caused by radial movement of a cylindrical heat source through a homogeneous medium of infinite extent. This problem represents a highly simplified model of the movement of a combustion front during the thermal recovery of oil. Numerical solutions are presented for a heat source moving at a constant velocity, and a velocity inversely proportional to the radial location of the heat source. Numerical solutions are presented for both finite and infinite vertical thickness of the heat source, i.e., with and without vertical heat losses. The numerical solutions are used to estimate the fuel concentration needed to maintain a combustion front during the thermal recovery of oil. The sensible heat carried to the combustion front by the injected gas stream is discussed in regard to the fuel concentration. Numerical solutions for a heat source (combustion front) of finite vertical thickness indicate the field conditions that may be necessary to sustain the temperature of a combustion front above the ignition temperature of the fuel over considerable distances from an injection well. The results also have implications in regard to the quantity of heat required during ignition. The results of this computation apply to a highly idealized model of a thermal recovery process. But the results may be used as a guide in engineering consideration of the thermal recovery process. INTRODUCTIO N The thermal recovery of crude oil has received considerable attention since the publication by Kuhn and Kochl of laboratory and field tests of this method of oil recovery. Other publications2,3,4,5,6, since that time have dealt with various features of the thermal recovery of oil and have illustrated the extremely complex nature of this process. Vogel and Krueger7 described an electric analog computer designed to solve a moving heat source problem which was analogous to movement of a combustion front during the thermal recovery of oil. The heat source was maintained at constant temperature and was a cylindrical source of infinite height (no vertical heat loss) moving radially at either constant velocity, or at a velocity inversely proportional to the radial location of the heat source. Jenkins and Ramey2 presented analytical solutions to a similar heat conduction problem and pointed out the possible importance of vertical heat losses. The following presents a general solution to the transient heat conduction problem introduced by Jenkins and Ramey4 as well as numerical solutions for a wide range of conditions possibly similar to those that might exist during field operation of the analogous thermal recovery process. DESCRIPTION OF PROBLEM The problem considered in this paper is determination of transient temperature distribution caused by a cylindrical heat source of infinite or finite vertical height, moving radially through an isotropic medium of infinite extent. It is further assumed that the heat flux generated at the surface of the moving heat source may be a function of time such that the fuel concentration required may be constant, or permitted to vary, and that heat is generated at the surface of the heat source only. In regard to the thermal recovery of oil the assumption that heat is generated at the surface of the front is equivalent to assuming that the thickness of the combustion zone is infinitely small, or that the reaction rate between fuel and oxidant gas is infinite. The last assumption does not appear stringent. See laboratory information published by Martin, et al3 Under these assumptions the temperature distribution throughout an infinite medium caused by a heat source moving radially with an arbitrary velocity may be described by The heat generation function or heat flux at the surface of the source, +(t), is Note that the fuel concentration may be defined as a function of time. Eq. 1 is derived in the Appendix.

By F. H. Deily, Jean M. Quets, Milton E. Wadsworth, John R. 222-000-000-012 Lewis, D. S. Rowley, R. J. Howe

Samples of synthetic magnetite were reduced in hydrogen-water vapor atmospheres in the temperature range 450o to 900oC. The reaction was always surface controlled, indicating the final products of reaction are nonfirotective. Three separate cases have been identified from the kinetic results: Case I, reduction of magnetite to iron below 570°C; Case II, reduction of magnetite to iron above 570°C; and Case 111, reduction of magnetite to wustite above 570 oC. In Cases I and 111 the kinetics have been explained by the formation of oxygen anion vacancies in the magnetite surface followed by associated diffusional processes. In Case 11 the observed kinetics have been related to the concentration of iron cation vacancies in the wustite layer formed, followed by associated steady-state diffusional processes. The concentration of cation vacancies in the wustite is maintained constant by the magnetite-wustite equilibrium. THE reduction of the oxides of iron has been a subject of study and interest for many years. However, few attempts have been made to interpret the results in terms of the mechanism of reduction of an iron oxide by either hydrogen or carbon monoxide. Stalhane and Malmberg' using CO, H2, and CO-Hz mixtures, developed the rate expression: where m = mass of oxide reduced, t = time, k = a constant, s = surface area, P = partial pressure of of CO or H,, and P, = partial pressure of the reducing gas at equilibrium. The rate of reaction per unit area was proportional to the difference between the partial pressure of the reducing gas and its pressure at equilibrium. Hansen, Bitsianes, and Joseph2 studied the reduction of pellets of hematite to magnetite with mixtures of CO-CO,. They concluded that below 450°C the reaction proceeded according to a model in which CO reacts with the hematite surface producing an oxygen ion vacancy. The rate controlling step was then assumed to be oxygen ion diffusion through vacancies resulting in the formation of magnetite. They derived an expression giving the rate of reduction proportional to the cO/CO, ratio. Recently McKewan3 published results for the reduction of magnetite spheres in atmospheres below 570°C. He explained his results by an equation of the form where K, is the equilibrium constant for wustite-iron equilibrium attributed to the formation of wustite as an intermediate in the reduction of magnetite. According to McKewan, Kp is an equilibrium constant for H, -HO adsorption in which oxygen is deposited on the surface from the H,Oand subsequently acts as a poison for reduction by hydrogen. Sample Preparation and Experiments. In this work the authors used the same apparatus and experimental procedure employed in the hydrogen reduction of magnetite. Sintered disk samples weighing approximately 1.5 g and measuring 1.2 cm in diameter and 0.25 cm in thickness were prepared by a method described previously.4 Partial pressures of hydrogen and water vapor were controlled by bubbling hydrogen through a series of flasks containing distilled and deionized water maintained at constant temperature in an oil bath. The total flow rate of the reacting gases—hydrogen and water vapor—was approximately 0.5 liter per min. The entire external system was maintained at a temperature above the oil bath to prevent condensation of water vapor. This was accomplished by wrapping electrical resistance elements over all surfaces. The glass column containing the weighing system-a McBain balance suspended from a gold chain-was enclosed in an aluminum tube heated by nichrome resistance wire enclosed in an insulating material. The temperature of the glass column was held constant by means of a series of thermocouples connected in parallel to a Leeds and Northrup temperature controller. This was necessary since variations in temperature resulted in expansion and contraction of the glass column and could be readily observed with the cathetometer. The spring extensions were measured through a window with a gaertner cathe-

Jan 1, 1962