Search Documents

By J. Weertman

High-temperature creep experiments were carried out on indium, lead, and on binary substitutional alloys of In-Pb, In-Sn, In-TI, In-Cd, In-Hg, Pb-Bi, Pb-Sn, Pb-In, and Pb-Cd. The stress at which the power law creep equution breaks down was found to be much smaller for indium and lead than for metals with larger elastic moduli. The exponent over the stress in the power law creep equation was found to decrease upon alloying from values close to 4.5 to values near 3. THIS paper describes a set of high-temperature creep experiments made on high-purity lead and indium and on lead-rich and indium-rich single-phase binary alloys of various metals. These ex- periments were carried out to check two predictions of some creep equations derived by us"2 from a dislocation creep model due essentially to Mott. This model is shown in Fig. 1. Here dislocation loops are emitted from sources, not shown, situated on different slip planes. As the loops expand they come into each others' stress fields and are stopped. However, at high temperatures, as Mott has pointed out.

Jan 1, 1961

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average. $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped udder the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton., Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand Mines Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all feeding into the same system.

Jan 2, 1916

By Yap Chu-Phay

ALTHOUGH chronologically, the Sb-Bi system was the first one studied by the writer, the theoretical basis of the equations used in this paper is fully discussed in the writer's paper on the iron-carbon system,1 because he believed that many would be more interested in the iron-carbon alloys. He suggests, therefore, that the reader consult that paper to familiarize himself with the theoretical aspect of the thermodynamic treatment outlined herein. This paper is divided into two parts: Part I deals with the Sb-Bi system and Part II deals with the lead-rich side of the Sb-Pb system. Although the former system has not much practical interest now, it has great theoretical interest in that it, is the one system that for a long time was thought to have (and under specific conditions still has) an anomalous solidus, which no amount of physical investigation could adequately account -for. The latter system of course, is particularly interesting in the lead-rich end. It will be shown that the thermodynamic method is capable of predicting reliably the equilibrium position of the solidus, and thus acts as a check on the experimentally derived solidus.

Jan 1, 1931

By Edgar G. Hill

Much has been written and said recently about the methods used and materials and equipment employed in building the long tubes that criss-cross a great part of the United States, like the pattern of a spider's web. This paper will discuss the fundamentals of design of these lines from the economic as well as the engineering viewpoint, pointing out the effect of the volumes transported, and the load factor, on the unit costs of transportation, as well as the effects on costs of the character 01 the fluids the lines are called upon to handle. Generally speaking, crude-oil pipe lines carry oil from the producing fields to the refineries. Sometimes part of the journey is by pipe line to a coastal point and tank ships are employed for the rest of the trip. The main lines of directional flow of crude oil through pipe lines in the United States are shown on Fig. I, but this, of course, does not always show individual pipe lines. Basic Formula for Flow OF Crude Oil The laws governing the flow of crude oil through pipes are well known. The basic

Jan 1, 1942

By Edgar G. Hill

Much has been written and said recently about the methods used and materials and equipment employed in building the long tubes that criss-cross a great part of the United States, like the pattern of a spider's web. This paper will discuss the fundamentals of design of these lines from the economic as well as the engineering viewpoint, pointing out the effect of the volumes transported, and the load factor, on the unit costs of transportation, as well as the effects on costs of the character 01 the fluids the lines are called upon to handle. Generally speaking, crude-oil pipe lines carry oil from the producing fields to the refineries. Sometimes part of the journey is by pipe line to a coastal point and tank ships are employed for the rest of the trip. The main lines of directional flow of crude oil through pipe lines in the United States are shown on Fig. I, but this, of course, does not always show individual pipe lines. Basic Formula for Flow OF Crude Oil The laws governing the flow of crude oil through pipes are well known. The basic

Jan 1, 1942

By V. D. Perry

Mineralized breccia pipes, because of their wide-spread occurrence and close structural relations to some of the world's great ore bodies, are objects of unusual interest for mining engineers and geologists. The literature contains many references to them, but it is questionable whether their genetic significance and economic importance have been sufficiently emphasized. The purpose here is to stress these features, relating them to the field facts, for the particular benefit of younger generations of geologists who, confronted with and sometimes confused by the growing flood of geochemical, geophysical, and other specialized research approaches, may be reassured that mappable field relations remain a foremost guide to a better understanding of ore deposits. A mineralized breccia pipe is a pre-mineral, breccia structure which has controlled the circulation and deposition of subsequently introduced mineralization. It is composed of relatively rotated angular or rounded rock fragments, set in a mineralized matrix. A pipe in plan outline may be circular, oval or approach polygonal form, with a steep to vertical axis proportionately much greater than its horizontal dimensions. The pipe is a steeply plunging, chimney-like mass of brecciated rock cemented with later minerals.

Jan 4, 1961

By W. H. Bassett, J. C. Bradley

In their paper on the directional properties in cold-rolled and annealed commercial bronze,' Phillips and Samans suggest that cupronickel, under distinctly different treatments, shows both "45" ears" and "90" ears. Fig. I shows the ears on some cupronickel cups made some 17 years ago for bullet jackets for small arms ammunition. In this case the material heated to 425° C. had "45" ears, while that annealed at 950°C. showed long "90" ears" when drawn with the same tools. The method of cupping, the shape of cupping tools, etc., were found to have very little influence on the earing tendency, but the deeper the cup was drawn, the higher the ears would be. Method of Manufacture Cupronickel cast bars were 1 in. thick. Ordinarily, they were rolled with numerous passes to a thickness of 0.4 to 0.2 in., according to conditions. They were then given a single intermediate anneal, and rolled to finish thickness, frequently 0.032 in. After a last anneal the material was cupped with a "cut and draw" operation. Progress of this is indicated in Fig. 2, illustrating five different stages at which the drawing

Jan 1, 1933

By Henry M. Bates, Roscoe Pound

Mr. Chairman and Gentlemen: I accepted your Chairman's invitation to speak to a group of experts in this field with the greatest hesitation, because I know little or nothing about it. Certainly I can make no detailed suggestions, or suggest planning along very definite lines. You cannot do that sort of thing in a vacuum, and as I have suggested, my knowledge of the whole oil problem is next to nothing. It is possible that as a student of our public law, constitutional law particularly, for a number of years, I have acquired a perspective that may enable me to offer, for what they are worth, some general thoughts on these problems. I think that nothing in the whole field of law requires more definitely and clearly the functional approach than does the problem of a sound legal solution of the difficulties of the oil and gas industry. The industry is dealing with substances that are peculiar, and one must know how those substances act and what has been the history of the industry, to undertake to make anything like specific suggestions. I certainly am not qualified.

Jan 1, 1935

By O. M. McRae. Discussion by R. W. Jones

R. W. Jones (Senior Exploration Geologist, Standard Oil Co. of California, Box 250, Seattle, Wash.) -Mr. McRae6 and his colleagues are to be congratulated for providing a more coherent structural synthesis of the complex structure in the Courtland-Gleeson area, Cochise County, Arizona, than the "gigantic thrust breccia" concept of Gilluly. 4 However, a few problems of interpretation remain. It is the intent of this note to point out some of these problems, and, drawing on my own work in the area as well as the work of McRae6 and Gilluly, 4 to suggest some interpretations which differ from those previously published. GRAVITY SLIDES In an unpublished manuscript (Jones5) I previously argued that most of the complex structures in the Courtland-Gleeson area can be most reasonably interpreted in terms of gravity sliding caused by uplift and eastward tilting of Jurassic intrusives and associated Paleozoic rocks. Although the field work and drill hole data described by McRae6 provided excellent documentation for two important gravity slides, McRae6 interpreted the basic structure in the Courtland-Gleeson area in terms of major eastward directed thrusting. I continue to disbelieve the

Jan 1, 1967

By E. H. Sellards

PHOSPHATE rock like most other mineral substances is found in nature in varying degrees of purity. Of the impurities that are present some are constituents of the rock itself; others are inclusions of a foreign substance within the rock; while still others represent merely associated materials or minerals, either clinging to the rock or found in cavities and natural depressions, and hence largely removed in mining. Some of these impurities are distinctly deleterious to the processes of manufacture for which the phosphate is mined, while others, although neutral in action or nearly so, yet by their presence reduce the average grade of the rock and thus acid useless bulk to the shipment. It is the object of refined processes of mining to bring the product, as delivered from the mine, to the highest possible grade consistent with the market requirements and demands. This, however, is not accom-plished without actual loss in the form of discarded phosphate. It is evident, therefore, that the devising of methods for reducing this loss in mining, and yet maintaining the grade of the rock which the market requires, is one of the serious problems that the producers have to face.

Jan 9, 1914

By Homer W. Riley, C S. Jenkins

SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron- plates, .broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, [ ] into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tool design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls. Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, there- fore, of slow-speed, compound geared rolls, especially for breaking the

Jan 1, 1943

By H. Rosenthal, A. L. Jamieson

Stress-corrosion cracking of copper-base alloys is of considerable importance and has been the subject of many investigations which employed various accelerated tests and long-time service tests. The outstand¬ing accelerated tests used are variations of either the mercury cracking test reported by Rogers in 1905( 1)2 or the ammonia test reported in 1910(2). The ease of applica¬tion of the mercury test is probably the reason industry adopted it. Subsequent investigation of this test(3,4) revealed that a minimum threshold stress was necessary before mercury cracking could develop. Since season cracking has been found in some instances in caliber 0.3o ammunition which has passed the mercury test, it is evident that the threshold stress value of the mercury test may be too high for dis¬tinguishing between acceptable and un¬acceptable caliber 0.30 cartridge cases. This condition has naturally led to the study of an ammonia test with its ability to cause cracks with almost any stress level. But the lack of a definite threshold value means that standards are necessary for evaluating the results of the ammonia test.

Jan 1, 1945

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

By Nicholas J. Grant, Raymond E. Cairns

A high-purity chromium, made by solid-state extrusion, and a series of molten, extruded, dilute alloys containing carbon, oxygen, nitrogen, and sulfur were studied to establish the effects of composition, cooling rate, grain size, strain rate, and prior strain on the transition temperature for brittle THE transition from ductile to brittle fracture with decreasing temperature remains of extreme interest especially among the refractory metals, such as tungsten, molybdenum, and chromium, which have relatively high transition temperatures. Fracture, yield stress, and hardness. Tension tests at a strain rate of 0.015 per min were generally utilized. Results are interpreted in terms of the quantity of each element retained in solid solution. Of these elements, chromium has been studied the least, but deserves additional attention because of its superior oxidation resistance for high-temperature use. In the past, impurity elements which have received attention are carbon, nitrogen, oxygen, and sulfur;'-' of these, nitrogen has usually been considered to be the most detrimental. Unfortunately, because of different levels of both specific and total impurity content, and because of the many different test and evaluation techniques used, a clear, definitive picture of brittle fracture in chromium has not been forthcoming. However, many

Jan 1, 1964

By R. B. Mears, E. H. Dix, R. H. Brown

In the Institute of Metals Division Lecture of 1940, E. H. Dix, J~.(I)~ discussed the acceleration of the rate of corrosion by high constant stresses. Experimental data obtained on this subject at the Aluminum Research Laboratories and a theory compatible with these facts were included in that lecture. The present paper contains data and ideas subsequently developed at the Aluminum Research Laboratories. Dix pointed out that in order for acceleration of corrosion by constant stress to occur: (1) There must exist in the alloy a susceptibility to selective corrosion along more or less continuous paths, as for in- stance at grain boundaries, and (2) There must exist a condition of high stress acting in a direction tending to pull the metal apart along these continuous paths. Acceleration of corrosion rate by stress is not confined to any one alloy system. Table I lists some of the metals and alloys and some of the corroding environments in which acceleration of corrosion by stress was sufficient to cause cracking (stress- corrosion cracking). It will be noted that the variety of alloys in which stress-corrosion cracking has occurred is rather large. Also, it will be observed that

Jan 1, 1945

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By E. M. Wise

THE practice of adding moderate quantities of nickel to a variety of bronzes has been employed by foundrymen for many years with several objects in view. In some instances it was desired- to harden the alloy; in others it was to increase the fluidity or to improve the solidity of the castings, or to refine their grain. These important matters have been considered in detail by Pilling and Kihlgren1 and by numerous other workers cited by them, and with the exception of the first will not be considered in the present communication. The possibility of reducing the cost of bronze by replacing a portion of the tin with nickel received attention some years ago by Burgess and Woodward,2 and, as will be shown later, offers attractive savings in cost under present conditions. The age-hardening characteristics of the nickel bronzes of appropriate compositions have been known for some time and were mentioned by Price, Grant and Phillips3 and discussed by Wise4 in connection with their paper. These matters are further considered in recent patents,5 and are becoming of commercial importance in the production of high-strength castings.

Jan 1, 1934

By John V. Beall

Hard as the Revett quartzite are conditions governing the deep mines of the Coeur d'Al6ne. In fourscore years of mining, heat and pressure have been the rewards of preseverance. Such obstacles are the natural concommitant to search for ore at depth. But high cost and shortage of miners is a creeping frustration of the decade. These grim observations were made on a trip to the mines of the Coeur d'Al6ne in the first week of May. But the bouncy optimism of competent mining engineers and geologists overrides by far the tough conditions. This is the story of what they are doing. I think they are setting the stage for the wonder mines of tomorrow. I didn't meet all the people or see all the mines, so there are unfortunate gaps in the story. Then too, sometimes the muck and water blotched my notes, or I couldn't write fast enough or I was too tired. No matter. There is much to tell and, because it is basically a human story, I am flouting the rules of technical journalism and couching it in the neglected "I" person. First then, a little history . . . .

Jan 7, 1966

By F. W. Schroeder

AT the annual meeting of the Institute 2 years ago, a paper,1 " Requirements of Refractories for Open Hearths," was presented by F. W. Davis and G. A. Bole of the U. S. Bureau of Mines. In a brief foreword, D. A. Lyon stated that the paper was not to report the results obtained but rather to present an outline to serve as a basis for discussion. The essential parts of an open-hearth furnace were described and the conditions under which they operate. Some constructive discussion followed the reading of the paper. One of the first fellowship investigations undertaken by the Bureau of Mines in 1924 under the cooperative agreement with Carnegie Institute of Technology, through the Metallurgical Advisory Board, was to determine service conditions of open-hearth refractories. The present paper gives the results of this work which was done in the Pittsburgh district and was in charge of the authors. Material contributions in the form of data were contributed by E. N. Bauer, J. W. Campbell, G. H. Pfeiffer and A. Grodner, Carnegie Institute of Technology research fellows. The study covered 18 mos.

Jan 7, 1926

C. W. Kempton, Oro Blanco, Ariz.: In his interesting paper, Mr. Ingalls refers to reports of tin-deposits near Sain Alto, Zacatecas, Mexico. During 1891 I made some personal examinations of these deposits. They are, for the most part, located from 10 to 30 miles west of the town, in the Sierra del Fraile.

Jan 1, 1896