Search Documents

By J. S. Miller

THIS paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Nesquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 ft. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65° and 70°. Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. 1), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired.

Jan 3, 1925

By S. Skowronski

The melting of cathode copper, ususally containing 95.98+ per cent. • Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulfur, however, so much sulfur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period—saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;'' this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulfur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulfur will ruin copper for practical purposes. The sulfur absorbed by copper during the melting period comes from two sources: (1) the sulfate left on the cathode sheets in the tank houses; (2) the fuel. The percentage of sulfates on the cathodes is variable, and depends on the care taken in washing the cathodes after removing

Jan 1, 1919

H ORACE VAUGHN WINCHELL was born at Galesburg, Michigan, Nov. 1, 1865, and died at Los Angeles, California, on July 28th of this year, at the age of fifty-seven. Mr. Winchell was one of the conspicuous geologists of his time. It may fairly be said that he was a geologist born and reared. His father, N. H. Winchell, was professor of geology at the University of Minnesota; his uncle, Alexander Winchell, was professor of geology at the University of Michigan. Under both of them Horace studied, graduat-ing at the University of Michigan in 1889. Mr. Winchell at once began that active life in the field which he followed for 34 years and until his death. The first years of his professional life were largely spent in the study of the iron ranges of Min-nesota. In 1898, he re-moved to Butte and became geologist in charge of the geological depart-ment of the Anaconda Copper Mining Co. and allied companies. There he remained for eight years. This period covered the trying days of the mining controversies be-tween the Anaconda and associated companies and the Heinze interests, and it fell to Mr. Winchell to direct the geological studies and development in connec-tion with that litigation. Recognizing the importance of careful geological study in the practical operation of mines, he organized and developed the splendid geological department of the Anaconda Copper Mining Co. This was one of his greatest contributions to the mining industry. Probably no mining company has attached the impor-tance to geological study and continuity of geological mapping in connection with mining operations that the Anaconda company has. It has given broad authority to its geological department and the development of its mines is under the direction of its geologists. The broad vision of Mr. Winchell was responsible for the adoption of this policy, one which is being profitably employed by many other organizations.

Jan 9, 1923

By P. D. Wilson

The genesis of some orebodies has been explained by the mingling and chemical interaction of water solutions of different compositions and the consequent precipitation of the mineral load of one or both solutions at their confluence. While this process can be proved in the laboratory, rarely can a positive demonstration be found in nature, for the conditions at the time an ore deposit is being worked are usually entircly differcnt from those that existed when the orebody was formed. For this reason, the present deposition of copper carbonate in the southern end of the Briggs mine of the Calumet and Arizona Mining Co. near Bisbce, Ariz., is of great interest. The developed orebodies in the Calumet and Arizona mines are roughly confined to two broad parallel zones separated at the north by a wedge of Copper Queen ground and at the south by an undeveloped block of Calumet and Arizona ground about 2000 ft. (610 m.) wide. The more westerly zone includes the Irish Mag, Oliver, P. and D., and Cole mines, none of which has been operated since 1919. Much of the water from this division is carried from the 1400-ft., or bottom, level at the southern end of the Cole mine in a long water drift through the undeveloped block to the 1300-ft. level of the Briggs mine at the southern end of the more easterly zone. Most of this water comes originally from outlying areas in the P. and D. mine, passing through parts of the lower. levels of the Cole mine, which are heavily mineralized with iron and copper sulfides. This sulfide zone has been opened up and slowly oxidizing for years. Originally a pure, potable water, the analyses of which are shown under A- in Tables 1 and 2, on its way through the mineralized area in the Cole mine it gathers copper, calcium, magnesium, iron, and aluminum sulfates, a load of dissolved mineral salts almost four times as great as that which it formerly carried; analyses B

Jan 1, 1923

By H. Vance

In 1932, as in 1931, the East Texas area outside the Gulf Coast exerted ' its influence over the entire petroleum industry. Practically 60 per cent of the oil wells completed in the United States during 1932 were in this area, development being chiefly confined to the East Texas oil field in Upshur, Gregg, Rusk, Smith and Cherokee counties. This East Texas area is geologically an interior salt dome basin, along the western edge of which are located the fault line fields as represented by Mexia and Powell. Production occurs on salt domes in the interior of the basin as represented by Boggy Creek and possibly Van, although no salt has actually been discovered in drilling at Van. Shore line conditions on the east side of this basin along the flanks of the Sabine uplift have been responsible for the East Texas oil field. Many known salt domes in the center of this basin have been tested but as yet have failed to produce oil in commercial quantities. The main producing horizon throughout the area is lowermost upper Cretaceous and is known locally as the Woodbine sand. The East Texas Oil Field Development.—Approximately 6000 producing wells were completed during the year in the East Texas oil field. No accurate estimate of the total initial production of these wells is available because few initial production tests were made as the wells were completed. The writer estimates the average initial production of these completed wells at 2500 bbl. per day while flowing wide open through tubing. Based on this estimate, the total initial production of the wells completed during the year is 15,000,000 barrels. At the close of 1932 there were approximately 9500 completed wells in the East Texas field. Of this number 176 were without pipe line connections. The oil produced from these unconnected wells could be marketed for $0.30 per barrel while the price paid for oil run from the connected wells was $0.75 per barrel.

Jan 1, 1933

By G. Czupryna, S. Natansohn

Electrowinning is the prevalent technique for recovering silver from wastes generated in silver-tungsten electrical contact fabrication. Such scrap is placed in a permeable plastic basket, which constitutes the anode compartment, and is suspended in a larger cell where the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand mg/L (oz per gal), necessitates additional purification of the deposited Ag and its removal would, therefore, be advantageous. Eliminating the W impurity also extends the operating period of the cell with corresponding increases in the Ag output and savings in labor costs. The solution to this problem lies in the selective removal of the W from the AgNO3 electrolyte either by liquid-liquid or liquid-solid extraction. Although W extraction in the liquid-liquid mode with a quaternary amine or other reagents as extractants appears feasible, particularly in view of the low pH (about 1.5) of the system, this approach was not considered because it is essentially a batch-type process. It is a more elaborate industrial operation than extraction by ion exchange resins. Implementing the latter process consists of passing the electrolyte from the electrowinning cell through an ion exchange column which would extract the tungsten selectively and returning the tungsten-free stream to the cathode compartment. This process continues until the W extraction efficiency decreases (as a result of resin loading) below an acceptable value. The electrolyte is then directed through another, similar column while the W values are eluted off the first one and the resin is regenerated for another cycle. Thus, two columns in a parallel flow pattern provide the means for continuous processing of the electrolyte feedstock.

Jan 1, 1984

By B. J. Yamada, D. W. Fuerstenau

Long-chained neutral molecules (decyl alcohol) increase the flotation of corundum with sodium dodecylsulfate and trimethyldodecylammonium chloride as collectors. This phenomenon is postulated to result from coadsorption of the neutral molecules with the collector ions. Flotation and streaming potential experiments have shown that sodium laurate is an effective collector for corundum at more dilute concentrations than sodium dodecylsulfate or sulfonate.1>2 It has been postulated that this phenomenon results from the adsorption of both laurate ions and lauric acid molecules, whereas sodium dodecylsulfate can be adsorbed only as dodecylsulfate ions, since this collector does not hydrolyze under flotation conditions. Similar effects have been observed in alkaline solutions with dodecylammonium chloride and trimethyldodecylammonium chloride as collectors.' If in- creased flotation occurs with the collectors which hydrolyze because of adsorption of the neutral molecules, purposeful addition of long-chained molecules should increase the flotation rate of minerals with such collectors as sodium dodecylsulfate or trimethyldodecylammonium chloride because these long-chained molecules should coadsorb with the collector ions. The effect of neutral molecules on flotation in these cases must depend on an adsorption mechanism which differs from that proposed by Cook for the adsorption of xanthic acid molecules by galena. For neutral molecules to function as collectors in the flotation of insoluble oxide minerals, adsorption of organic ions must first occur to provide a means of anchoring the fatty acid or amine molecules. Without adsorption of collector ions, flotation does not occur even in the presence of large quantities of neutral molecules, as is indicated by the cessation of flotation at low pH values with soaps as collectors or at high pH values with primary amine salts as collectors.' Neutral molecules, such as fatty acids, must be adsorbed through van der Waals attraction between the hydrocarbon chains of the adsorbed soap ions and the hydrocarbon chains of the fatty acid molecules. The mutual association of hydrocarbon chains results

Jan 1, 1962

By M. S. Azun

The authors' paper did not explain the facts and reasons why state companies are established and what their role is in international industrial mineral trading. Also. I do not agree with the conclusion implying that the main goal for state companies is to capitalize natural resources. Almost all state companies are founded by certain laws and their activities are arranged by state regulations. Their only aim is to operate mineral deposits for their people and to protect the rights of the people. Although some ore deposits, such as nonstrategic or small, may be exploited by privately owned companies, the state has the right to control the operation and production. Activities of state companies may or may not be widened because of the character of the deposits and the importance of the mineral market involved. For some countries, although governments may occasionally change hands, the policy of the mineral trading system is not affected by this change. There is no doubt that any government desires to make more earnings to increase GNP, when it is involved in operating and trading mines. It wants to produce and sell the finished products, instead of unprocessed ones, if possible. When it is known that some mineral deposits are relatively rare, such as Turkish boron deposits, the government can nationalize the mines to control production and affect the market. If there is an abundance of a certain mineral in the market, the government can cut production and set a floor price, such as Canadian potash. Also, when production of a specific mineral is unique, such as Turkish chromite, the price of such mineral may be set by correspondent government. One may add that if some governments with their state companies produce a certain mineral in a larger amount, they may decide to establish a cartel to protect their production and price. These are the facts followed by government-owned state companies and partially government-owned companies. The reason being charge of many deposits by the state companies is always the same: "protect" the mineral rights of the people.

Jan 1, 1985

BECAUSE you cannot always proceed by the ordinary pathway since you sometimes find yourself in a place where you cannot have all that you might need or wish, it often happens that it is necessary to know how to recognize and understand your materials well, in addition to having them well disposed, and to know how to use your, ingenuity in arranging a mould., Furthermore, things have a great diversity among themselves, and it is not possible to give a particular rule for all. But if you have a certain broad fundamental knowledge when you have need of many things, the ingenuity awakens and supplies its needs by imitation. Now, because I have thought that you had not hitherto had the slightest shadow of knowledge of what I have described in this treatise of mine, I have expanded and narrated things in greater detail than perhaps I might have done. For this reason I have also decided that I wish to tell you of several methods that can be used if you wish to mould, especially in making an intaglio* for a relief, t or in making another intaglio in bronze from either an intaglio or a relief. And I will tell how every relief reduces, itself from convex to concave and also how the relief is made from the intaglio. These works are first made of plaster or pastes or some other liquid thing that is soft when moulded and becomes hard either by drying out with heat or by shrinking with cold, such as tragacanth, plaster of Paris, sulphur, lead, wax, or similar things. And, in conclusion, we describe the method of making an intaglio from a solid. In making an intaglio you must first consider whether it is a large or small thing, figure or foliage, whether it is in demi- or bas-relief, and whether it is a thing that projects from the mould wholly or in part.

Jan 1, 1942

By M. H. De Hora

(Butte Meeting, August, 1913.) IN giving my opinion of the importance of Colombia as a field for investment for those interested' in mining for the precious metals, I must begin by quoting Sir Clement Markham, who, in one of his presidential addresses to the Royal Geographical Society of Great Britain, called the attention of its members to the fact that " although Colombia is the least known and least developed of the South American republics, it is far and away the richest mineral country of them all." This to American investors is extremely interesting, as the country is the most accessible of all the South American republics from the United States. .Almost all of the gold shipped by the Spaniards from Madre de Dios, now Colon, came from Colombia, and statistics from the Mint at Medellin, the capital of the Department of Antioquia, go to show that the . total production of the precious metals of Colombia, dating from the Spanish conquest in the fifteenth century to the present time, aggregates the enormous total of $700,000,000. Of this amount, nearly 70 per cent. represents gold obtained from the placers of the Republic, more than one-half of which came from the Department of Antioquia, the balance, being divided between the placers of the Choco and the rest of the Republic. The remaining 30 per cent. of the $700,000,000 represents the silver and gold obtained from the quartz mines, the silver greatly predominating. A glance at the map of Colombia shows the territory somewhat in the shape of an outspread human left hand extended palm downwards on the paper, with the wrist adjoining the Republic of Ecuador, the bones of the hand, fingers, and thumb representing the divisions of the great Andean mountain chain known as the Cordilleras of Colombia. The first finger represents the Eastern Cordillera, with the thumb as the extension to the Nevada de Santa Maria, forming

Jan 7, 1913

By William Firmstone

ON the 19th December, 1833, a patent was granted to F. W. Geisenheimer, for smelting iron ore with anthracite. In his claim he says: "Sixthly, though I cannot, and do not, claim am exclusive right of the use of heated air, for any kind of fuel, nevertheless I believe to have a right to claim the use of heated air, applied upon, and in connection with, the said principle and manner discovered by me, to smelt iron ore in blast-furnaces with anthracite coal, by applying a blast of air in such quantity, velocity, and density, or under such pressure, as the compactness, or density, and the continuity of the anthracite requires, as above amply and fully described and illustrated." Dr. Geisenheimer made experiments in smelting iron ore with anthracite at the Valley Furnace, near Pottsville, but he failed to carry out to good practical results the principles enunciated in his patent. In the Journal of the Franklin Institute for February, 1838, a communication was published that was made by Mr. George Crane, of the Yniscedwyn Iron Works, South Wales, to the British Association, in September, 1837. On the smelting of iron with anthracite coal, Mr. Crane states therein, that he began the use of an¬thracite with hot-blast on the 7th February, 1837, in a cupola blast-furnace, 41 feet high, and 10' feet across the boshes ; product, 34 to 36 tons a week. Mr. Crane goes on to say, "It may not be uninteresting to be informed in what matter the idea first occurred to me of applying a heated blast to anthracite coal. One evening, after I had placed a piece of it upon my parlor fire (which had before been made up with bituminous coal), and had allowed it to arrive at a red heat, upon applying as fierce a blast to this piece of coal as I could raise from a pair of bellows, I noticed a black spot or mark

Jan 1, 1875

By G. C. Wallick, W. R. Foster, J. G. Savins

The theory of the differentiation method for the Couette flow experiment is reviewed. Particular attention is given to the requirements on data analyses in the case of the class of non-Newtonian materials described as viscoplastics, i.e., materials characterized by a yield point or yield stress. Here changes in boundary conditions arise when the shearing stress attains a critical value with the result that the form of the basic integral equation for Couette flow is determined by the flow conditions existing during the measurement. INTRODUCTION In the preceding papers in this series,l,2 the salient features of the differentiation method of rheological analysis in Poiseuille-type flow were discussed. It was shown that a dual differentiation-integration method analysis of the Poiseuille flow of idealized generalized Newtonian and visco-plastic models could be used to develop a spectrum of highly sensitive response patterns in terms of certain characteristic derivative functions. These functions were shown to optimize the selection of the most appropriate functional relationship between f(p) and p from the Poiseuille flow experiment. The present paper reviews the theory of the differentiation method as applied to the equally important Couette flow experiment. We will also discuss the range of variables over which the basic integral equation for Couette flow is applicable when the non-Newtonian material is of the viscoplastic type, i.e., characterized by a yield point or yield stress. THEORY Having described the application of the differentiation method to Poiseuille-type flow in the preceding papers, we now proceed to the case where the test liquid is confined to the annular space between coaxial cylinders of length L, one of which is in motion, i.e., Couette flow, formulating the basic integral equation after the method of Mooney.3 The observed kinematical and dynamical quantities are the angular velocity O and the torque T. Here, the one nonvanishing component of the shear-rate tensor is

By M. A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing

Jan 1, 1981

By Philip Wilson

THE genesis of some orebodies has been explained by the mingling and chemical interaction of water solutions of different compositions and the consequent precipitation of the mineral load of one or both solutions at their confluence. While this process can be proved in the laboratory, rarely can a positive demonstration be found in nature, for the conditions at the time an ore deposit is being worked are usually entirely different from those that existed when the orebody was formed. For this reason, the present deposition of copper carbonate in the southern end of the Briggs Mine of the Calumet and Arizona Mining Co. near Bisbee, Ariz., is of great interest. The developed orebodies in the Calumet and Arizona mines are roughly confined to two broad parallel zones separated at the north by a wedge of. Copper Queen ground and at the south by an undeveloped block of Calumet and Arizona ground about 2000 ft. (610 m.) wide. The more westerly zone includes the Irish Mag, Oliver, P. and D., and Cole mines, none of which have been operated since 1919. Much of the water from this division is carried from the 1400-ft., or bottom, level at the southern end of the Cole mine in a long water drift through the undeveloped block to the 1300-ft. level of the Briggs mine at the southern end of the more easterly zone.. Most of this water comes originally from outlying areas in the P. and D., mine, passing through parts of the lower levels of the Cole mine, which are heavily mineralized with iron and copper sulfides. This sulfide zone has been opened up and slowly oxidizing for years. Originally a pure, potable water, the analyses of which are shown under A in Tables 1 and 2, on its way through the mineralized area in the Cole mine it gathers copper, calcium, magnesium, iron, and aluminum sulfates, a load of dissolved mineral salts almost four times as great as that which it formerly carried; analyses B

Jan 7, 1922

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s7 the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing

Jan 1, 1981

By S. J. McCarroll

J. Bruce Clemmer, J. B. Rosenbaum, and C. H. Schack (U.S. Bureau of Mines, Salt Lake City)—We have watched with considerable interest Three Kids development of Manganese Inc. and have been impressed by the ingenuity with which management and staff have solved their many obstinate handling problems. Mr. McCarroll has been lenient in describing the difficulties faced by the company in developing a process for beneficiating Three Kids ore. The operation, equivalent in size to a 20,000-ton sulphide ore plant, is treating a unique ore by a flotation process pioneered by Manganese Inc. Perhaps the magnitude of the conditioning and flotation problems peculiar to Three Kids ore can be better appraised when it is pointed out that two-thirds to three-fourths of the ore is floated in the rougher step and that the four stages of cleaning which follow are equivalent to floating the whole plant feed two to three times. Our experience in both laboratory and pilot plant flotation of Three Kids and other manganese ores leads us to agree with Mr. McCarroll that suitable conditioning is a prime requisite for successful oil-emulsion flotation. The difficulties of proper conditioning were demonstrated in pilot plant processing of Artillery Peak manganese ore at our Boulder City, Nev., experiment station. Over three months of experiments and extensive plant revision were required before satisfactory conditioning was obtained in the 25-ton-per-day plant. Such factors as time, type and intensity of mixing, aeration, surface to volume relationship, and power input are still being studied by the Bureau of Mines in hopes of learning how best to condition manganese pulps for oil-emulsion flotation. Other factors affecting flotation of manganese with oil emulsion also deserve attention. A few of these are the influence of stability and proportion of ingredients in the collector emulsion, the feasibility of grinding

Jan 1, 1955

The editorial expenses for the preparation of the manuscript of the second edition, as for the first, were provided by grants of the Engineering Foundation and the Open Hearth Steel Committee of the Iron and Steel Division, AIME ; the Seeley W. Mudd Memorial Fund again sponsored the publication of this volume. The companies and research or educational institutions with which the authors, reviewers, and editors are connected also contributed much to the writing and editing of this book through their generous donations of time and travel and office expenses. And finally, the authors and others have given countless hours of their own time with no recompense but the satisfaction of a job well done. In order to give credit to the companies or educational institutions which made it possible for the members of the Editorial Board to devote considerable time to the revision of this book, the names of these members and their affiliations are recorded here as follows : W. O. Philbrook, Carnegie Institute of Technology M. B. Bever, Massachusetts Institute of Technology H. B. Emerick, Jones and Laughlin Steel Corporation B. M. Larsen, United States Steel Company A number of individuals suggested desirable changes in the book before rewriting was started. Almost all manuscripts were gone over critically by reviewers, and the resulting criticisms led to the correction of errors and omissions and greatly contributed to the accuracy and completeness of the text. Other people have supplied additional data or illustrations or assisted in other ways. While some of these contributors must remain anonymous because they are not known to the Editors, the cooperation of the following individuals is gratefully acknowledged : R. D. Allen, Republic Steel Corporation, Chicago Isadore Amdur, Massachusetts Institute of Technology Mary Baeyertz, Armour Research Foundation S. P. Bahmer, Republic Steel Corporation, Massillon E. C. Bain and Associates, United States Steel Company, Pittsburgh C. W. Briggs, Steel Founders' Society of America H. W. Briske, Wisconsin Steel Works

Jan 1, 1964

By E. C. Mahan

THE text of my talk was suggested by the invita-tion of your secretary, who said that the excess productive capacity of the bituminous industry was a matter of common concern to engineers and coal operators. Cognizant of the depressed condition of the industry, he tactfully added that in common council we might find wisdom. Certainly it would seem that the application of the best engineering knowledge available would be helpful in solving mining problems. There is no doubt that clear thinking, characteristic of the engineering type of mind, is essential to untangle the shapeless pattern which increased complication, so often mistaken for progress, has developed. There is much thinking today which neither looks forward to a logical combination of ideas nor backward to simple fundamentals. The result of that sort of thinking is hopeless confusion. Lately we have heard much about excess capacity and overproduction, along with their attendant evils. Respecting the bituminous coal industry, these terms have been frequently misused. How many of us have seen them applied to the coal industry but how few of us have understood them. I am reminded of a state-ment which William Green, president of the American Federation of Labor and a former miner from the Ohio field, gave to the Associated Press last month, in which he was quoted as saying: "The coal men must realize that conditions have altered since the World War. To-day they are producing a billion tons a year, with a market for only half that tonnage." I cite this instance as a glaring example of the flood of. loose statements about the bituminous industry with which the public is being deluged. If the general public, or some of the newspapers, had any passion for the facts, this sort of misleading statement would not get very far. Unfor-tunately, in these days, opinions are more sought after than facts, and statements by such a person as Mr. Green and are promptly accepted by a credulous public.

Jan 4, 1928