Search Documents

By R. W. Prouty, R. T. Green

The object of this paper is to describe, as concisely as possible, the methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz. Because of the difference in occurrence, manner of prospecting, and methods of mining, the sampling and estimating practice falls into two divisions: That for the underground operations, and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three main classes: Replacements of limestone, replacements of porphyry, and replacements of contact breccia. The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies, it is exceedingly difficult, without sampling, to determine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft, As some of the orebodies are from 100 to 300 ft. thick, it can be seen that the smaller ones form a difficult prospecting and estimating problem. In the replacements in porphyry, both underground and in Sacramento Hill, the boundary usually cannot be determined without sampling. There is a gradual decrease in value until barren material is reached; this gradation may occur within a short distance or it may extend for several yards.

Jan 1, 1925

By A. G. Metcalfe, Koeneman

A study of the structure of chemically deposited nickel by Goldenstein, Rostoker, Scpssberger, and Gutzeit has been reported recently. In this work it was shown that the nickel deposit produced by the catalytic nickel-reduction process was an amorphous solid. Crystallization occurred at elevated temperatures when the original powder pattern which showed only a diffuse ring with a d-spacing of 2.01A became sharp, revealing nickel and nickel-phosphide lines. The phosphide was indexed provision%lly on a tetragonal lattice of parameters a = 9.01A and c = 4.42A, which is in reasonable agreement with the structure of Ni3P proposed by No-wotny and Henglein.3 The transformation from the amorphous to the solid state occurs abruptly (e.g., after 7 min holding at 400°C) with the evolution of considerably more than 1000 cal per gm-mole. A more detailed analysis of these effects requires a knowledge of the solubility of phosphorus in nickel. Konstanti-now3 mapped out the phase diagram in 1908 but did not determine the solid solubility. The eutectic was placed at 11 pct P and 880°C. The purity of typical catalytic nickel deposits is very high.' Spectrographic analysis for heavier elements showed only trace amounts of aluminum, calcium, iron, magnesium, lead, and silicon. The term "strace" is a qualitative definition for less than 0.1 pct and probably less than 0.01 pct. Analysis for the interstitial elements yielded 0.04 pct C, 0.0023 pct 0, 0.0005 pct N, and 0.0016 pct H. Some of this material with 7.5 pct P was used in the present work. EXPERIMENTAL METHODS Alloys were prepared from carbonyl-nickel shot and a master composition containing 7.5 pct P. Cold-crucible, nonconsumable-arc melting was used.

Jan 1, 1959

By G. P. Chatterjee

HARDNESS is one of the most common properties of metals and alloys but is one of the most difficult to define or express in terms of the fundamental units. In the Brinell or Vicker's hardness test, the hardness number N is defined as N = L/A where L is the load in kilograms and A is the area in mm'. This does not necessarily imply that a pressure of N kilograms per mm2 actually acts on the specimen.' It is essential that for a true comparison of hardness values the angle of indentation be kept constant,' a which is not done in the Brinell test. For this and other reasons, the Brinell hardness value is not based on a satisfactory physical concept.' The concept of hardness based on the work done per unit volume of indentation3-6 offers a simple and scientific definition. An attempt has been made here to develop this concept (at constant angle) and to compare the values so obtained with the Bhn for different metals and alloys. In Fig. 1 a vertical load L is applied to a compara- tively hard ball of diameter D creating an indentation of diameter 6 and depth h on the specimen S. The work done, W, is then given by W = So Ldh. [I] Since L is not independent of h, Honda and Takahasip and Matsumura" assumed different functions leading to equations which do not apply equallye to a wide variety of metals and alloys. A better relation is obtained from Meyer's Law L = ad" [2] where A and n are constants depending on the nature of the material but independent of the ball diameter D. From Fig. 1 it is obvious that h = R(l — cosq) and d = 2R sin 8.

Jan 1, 1957

By Harold Linke

THE following article presents notes and data compiled and computed by the writer for use in the determination of: size and slope of mill launders, details of junction boxes and downspouts, and distribution of pulp. It also includes pulp formulas, volume of discharge through bushings, paths of discharging streams, banking of turns and curves. In the design of a concentrating mill, the draftsman usually considers launders to the extent of providing ample "head" for transmission of pulp from one department of the mill to another. The superintendent of construction aims to build his launders wide and deep, and on a slope steep enough to ensure positive flow. So launders are laid generally on too steep a slope, with the result that the repair gang works to maintain launder bottoms and sides against the erosive action of the conveyed pulp. To this end many kinds of liners have been devised: concrete, mastic, white iron, glass, rubber. True, the reduction of slope to the point where a pulp will flow with minimum wear, will minimize labor and expense; but when the desired slope is not predetermined, the millman hesitates to readjust his launder slopes by cut-and-try methods. To the end that the desired size and slope may be found readily, the writer has: (1) conducted experiments with pulps of different specific gravity, screen analysis and dilution; (2) gathered a few graphic data from standard reference works (such as Peele's Mining Engineer's Hand-book and Taggart's Handbook of Ore Dressing); (3) computed several tables; and compiled results that have proved dependable for Utah Copper ore. It is quite possible that the following tables and graphs may not be applicable to all ores, but it is hoped that they may prove helpful, even in slight degree, in alleviating a portion of the trouble and migraine of some other millman.

Jan 1, 1939

By R. S. McCaffery, R. G. Stephenson

The statistical analysis of blast-furnace data was undertaken to determine some of the relations which exist between the variables involved in furnace operation, and particularly to show the effect of variation of slag composition on such economically important factors as coke consumption, daily tonnage of pig iron and sulfur elimination. It' was desired to correlate the results obtained in commercial practice with those predicted from a study of the quaternary system lime-alumina-silica-magnesia. This paper presents the results of a preliminary study of blast-furnace daily operating reports, and is intended to indicate the suitability of our method of attack and something of the results that may be expected from an extended statistical examination of such data. It has been shown that blast-furnace slags are not composed of oxides, as reported by chemical analysis, but are actually composed of several compounds, each made up of two or more of the oxides present.' These compounds persist in the liquid state, and the properties of a slag are the properties of a mixture of these compounds, and not of a mixture of the ultimate oxides. The oxides lime, alumina, silica and magnesia make up 94 to 96 per cent. of the usual blast-furnace slag, and assuming that we may neglect the remainder of the components, we may determine the minerals present, and their relative proportions, from a study of the quaternary system involving these four oxides. Operating reports from 15 furnaces were available for this investigation. Complete slag analyses for one slag per day were available, per-mittling the calculation of the mineral composition of the slags used. Basic, malleable and foundry irons, with silicon varying from 0.75 to 4.50 per cent. were included in the reports for this examination.

Jan 1, 1931

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By J. E. Gosline

In any theory of a hydrodynamic nature dealing with the vertical flow of gas-liquid mixtures in pipes, the two factors that present the greatest difficulty are the relative motion between the phases and the energy loss resulting from turbulence work. The former has generally been referred to in the literature as "slippage" and the latter as "friction." A third factor of importance is the nature of admixture between liquid and gas for both the relative motion between the phases as well as the turbulence work are functions of the type of mixture. Although much work of a general nature has been performed on the vertical flow problem, there have been very few attempts made to study experimentally the factors involved in the phenomenon individually. Of these, perhaps the most notable is the work of Moore and Wilde1 on slippage. Some writers on the subject have assumed that over a wide range of operating conditions the controlling type of mixture is one in which gas bubbles of uniform size are distributed throughout the liquid, and that the data obtained from experiments on the motion of single bubbles through various liquids may be used in evaluating the slippage. Ver-sluys2 has further assumed another controlling type of mixture in which the liquid occurs as a dispersed phase within the gas and applies data on the fall of drops of water in air to calculating the relative velocity. It was for the purpose of studying the applicability of data on single bubble motion to the slippage factor and to further observe the nature of mixtures that a research program was conducted at the University of California during 1932 and 1933. These experiments formed a basis for

Jan 1, 1936

By H. C. Vacher

THE limiting concentrations of carbon and oxygen which may co-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen .thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation with elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Herty1,2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550° to 1600 C. and one atmosphere pressure. Kinzel and Egan3 have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550°. C. In. order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume. a value of 0.0102 at 1580° C. for this

Jan 1, 1931

By Ian William Wark, Alwyn Birchmore Cox

Different parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. Experimental Method The methods used have been described previously.l-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1939

By S. F. Emmons

By far the greater number of the members of this Institute are men who are engaged in the strenuous work of the technical part of their profession, and find little time for the abstract scientific work which is less distinctly practical and pecuniarily remunerative. There is, however, a small but increasingly nu, merous class whose members devote themselves to broad geological problems which underlie the systematic development, and whose work, theoretically, ought to precede and form a basis for that of their more practical brethren. These are the so-called mining or economic geologists, who are, for the most part, connected with State or National geological surveys. Prom the character of their work, the life of these men necessarily follows rather different lines from that of most of their colleagues, and is not generally familiar to them. It seems admissible, therefore, that to the life of a prominent member of this class, who died during the past year, having literally sac-rified his life to his work, a more extended notice should be given than the relatively small number of his contributions to the Transactions night seem to justify. George Homans Eldridge, son of Ellery and Sarah (Mathews) Eldridge, was born on Cape Cod at Yarmouth, Mass.; Christmas day, 1854. His boyhood education in the public school at Yarmouth was followed by a six years' course in the Public Latin School at Boston, from which he entered Harvard University in 1872, being graduated with the highest rank in his class in the natural sciences in 1876. During his college course he spent the summers of 1875-6 at Cumberland Gap, Ky.,as volunteer aid to Prof. N. S. Shaler, who was then in charge of the State Geological Survey of Kentucky. This vacation work, undertaken by him rather as a pastime, gave him his first leaning toward geology. Soon

Jan 1, 1907

By L. H. de Wald, J. Walter Scott

It is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.' A wire bar cast in this manner is partly characterized by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish approximately the same result. Several wire bars of commercial size (250 Ib.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally. Experimental Procedure A horizontally cast bar and a vertically cast bar were obtained from each of several regular reverberatory furnace heats of copper which had been refined and poled to tough-pitch metal in accordance with usual methods.' Both bars were cast from the same part of the melt and within five minutes of each other, in order to produce as nearly as possible, in each case, wire bars of identical composition.

Jan 1, 1930

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By B. S. Butler

STUDY of the ore deposits of Colorado has disclosed, in numerous places, sharp changes in both mineralogy and metal content of the primary or hypogene deposits with change in depth. A clear understanding of the meaning of these changes is requisite to form intelligent conclusions that can be applied in the exploration of such ore deposits. This paper is an attempt to set forth some of the geologic and chemical relations of minerals that bear on this problem. The effect of the differing electrode potentials of elements on the order of oxidation and on the order of displacement of one metal by another metal in supergene sulfide deposits has been studied for many years by several investigators. The results all agree rather closely with the original Schürmann series of replacability of metal sulfides, as Wells has shown.1 So far as the writers are aware there has been little attempt from the geologist's viewpoint to correlate the electrode potentials of the elements, other than those of the common metals, with the positions and mode of combination of the elements as found in ore deposits, and in particular in hypogene deposits. Wells' discusses electrochemical activity between solutions and certain ore minerals and mentions the possibility of its effect in precipitation reactions. The senior writer for a number of years has emphasized the importance of oxidation-reduction reactions as a factor in the formation of certain hypogene ore minerals, and as the electrode potentials are a measure of the relative oxidizing and reducing power of the elements and their ions, it seems possible that a study of them may offer some suggestions on certain problems. The data at present available for such a line of attack on oxidation-reduction reactions are too far from complete to offer much help, nevertheless the table of standard electrode potentials

Jan 1, 1929

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Frank H. Probert

The mining laws relating to winding-ropes in some of the German provinces are very strict, and severe tests have to be periodically made to see that the ropes in use come up to the prescribed standard. A few notes on the method of testing the ropes and the results obtained may be of interest to the members of the Institute. Permission must be given by the Inspector of Mines to put up a winding-plant; and previous to installation a full report made by the manager, clearly setting forth all details of the shaft, the pit-head, engines and appliances appertaining thereto has to be sent to the mining officials. Accompanying each subsequent report, further details, such as the name of the firm supplying the rope, construction, quality of steel, date of installment, weight per meter, length, particulars of the safetycatches, cages, etc., must be given. At least one spare rope must be kept at ever? shaft ready for use in case of emergency. The rope must hang in the shaft, with cage attached, not less than twenty-four hours before it is used for winding; and it must have undergone a severe test in the manner hereafter described. The laws prescribe that when a rope is continually in use it must be tested every three months; but if the rope is only used every few days it must be tested at least every six months, in the presence of the superior officer; and notification of the date of testing has to be sent to the Bergrath two days before the test is made, in order that he can personally superintend the operation if he chooses. Should winding have been stopped for a long time, it is not necessary to test every six months; but before the rope can be used again it must be tested.

Jan 1, 1901

The purposes of composition are various; one purpose, for instance, is to make a record for the writer's own use, as in a diary. That does not involve responsibility to others. There is also the writing meant to influence opinion-to be persuasive and pleasing. With such writing we need not concern ourselves at this stage of our study. The prime purpose of technical writing is to be informative-to convey information; therefore it must be clear beyond the chance of misunderstanding. Such clearness is impossible if meaningless or ill chosen words are sprinkled through the text. Discard the trivial phrases that are constantly at your elbow. Brush aside a host of vapid superlatives. Metternich exclaimed: "The superlative is the mark of fools". It is a false emphasis, like the underlining in a school-girl's letter. For example, the little word 'very' can be deleted nine times out of ten; it is an impediment to terse and perspicuous writing, as the multitudinous hand-baggage of the British tourist is to his travel. 'Very' supposes comparison. A mine with a 1000-ft. shaft is very deep to the scribe who writes from the Joplin district, in Missouri, but it seems a shallow hole to a man living at Calumet, Michigan. A vein that is 10 feet across may be considered very wide at Cripple Creek, Colorado, but it is only a 'stringer' to the miner at the Homestake, in South Dakota. Ore assaying $20 in gold is very rich at Juneau, Alaska, where 10,000 tons of $1 ore is crushed daily, but it is relatively low-grade to the pocket-miner at Alleghany, in California. It is all a matter of comparison; unless the reader knows your standards of depth, width, or richness, your 'very' has no significance. "Where erosion was very rapid or oxidation very shallow"

Jan 1, 1931

By E. H. Hamilton, H. C. Vacher

The limiting concentrations of carbon and oxygen which may CO-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation witch elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Hertyl.2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550" to 1600" C. and one atmosphere pressure. Kinzel and Egan % have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550" C. In order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume a value of 0.0102 at 1580" C. for this

Jan 1, 1931

By G. W. Housner

The series of earthquakes in the vicinity of Koyna Dam in south- western India, which included a very damaging magnitude 6.5 shock on Dec. 11, 1967 (Dec. 10 GMT), is of much interest. The events are exceptionally well documented, which is a tribute to Indian geologists, seismologists, and engineers. To help in disseminating the information in the United States, this chapter presents a brief summary of the pertinent data and lists references. Koynanagar (Koynatown), which began as the construction camp for the dam, is located about 140 miles southeast of Bombay and 70 miles south of Poona at 17.4ºN and 73.7ºE, about 40 miles inland from the Arabian Sea. Koyna River flows almost due south from its source a distance of about 38 miles and then makes an abrupt turn to the east and travels some 480 miles to empty into the Bay of Bengal. Koyna Dam is located about 3 miles north of this turn. The approximately north-south trending continental divide is a few miles west of Koyna and the terrain drops steeply about 1700 ft to where the hydroelectric generating station is located. The reservoir behind Koyna Dam forms a long, narrow lake (Shiva- jisagar Lake) with mean water level (MWL) at 2160-ft elevation. The 345-sq-mile watershed receives an annual rainfall of about 200 in., most of which falls between mid-June and mid-October. The peak storage is 99 x l09 cu ft. A controlled flow passes under the continental divide in a tunnel and then down to the electric generating station about 5 miles WNW of the dam. The inflow not used for power generation is released to Koyna River. The Koyna project is a major source of electric power for Bombay and produces 540 MW at peak load.

Jan 1, 1970

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938