Search Documents

By N. Nemeth, L. L. Sirois

The role of the filter medium in continuous-vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and filter cloth are discussed. Due to negative pressure differential, gas bubbles evolve in the slurry, constrict passages in the filter cake and medium, and further restrict flow through the tortuous channels. Filtration is a liquid-solid separation process taking place at a porous medium under a pressure differential. The liquid passes through the medium; the solids are retained on the medium as a partially dewatered cake. Filtration is far from a simple process and has been described in terms ranging from "complex" to "subtle." Because of the many variables involved, no unified filtration theory has been developed, and the filtration process is still considered very much an art. In industrial filter design, basic relationships, whether derived for idealized conditions or developed empirically, are usually adapted to suit local conditions. In the mining industry where continuous-vacuum filtration is the main dewatering process, the physical state of the concentrates and the relatively low pressure differentials permit the assumption that the cakes are noncompressible, an assumption which leads to the use of theoretically sound rate equations. Notwithstanding this simplification, there are other problems, unique in the application of vacuum to dewatering, and until now completely ignored, which demand special attention. The basics of filtration involve the capture of solids on, while permitting the flow of liquid through, a porous layer of cake and cloth. Flow is determined by the structure of the solids which make up the cake and the particles permanently attached to the cloth. The problem of this structure, essentially one of solid geometry, has been considered insoluble by Hatscheckl as early as 1907 and by Freshwater as recently as 1967. Since cake structure is determined by the slurry parameters, that problem is far too large for inclusion in this study. For theoretical considerations, uniform buildup of the filter cake must be assumed; and for efficient practical operation, the resistance of the medium must be kept constant over long periods. The latter can be achieved by careful selection of the filter cloth, since the greatest part of the total filtration resistance will develop at the cake-cloth contact. This paper discusses the role of the filter medium in continuous vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and the filter cloth.

Jan 1, 1971

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been caleulated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware. no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been caleulated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware. no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By F. M. Yans, A. D. Donaldson, A. R. Kaufmann

Beryllium was mixed by powder. metallurgical techniques with copper, nickel, iron, and chromium, respectively, to form beryllium -rich binary alloys which Mere then extyuded and rolled transtverse to the extrusion direction. The effect of each alloying element was determined by tensile testing. In solid solution, small amounts of iron and nickel had an embrittling effect, while copper in solution increased the strength but had no effect on ductility. The effect of chromium was complicated and not readily explainable. Observations concerning the planes and modes of fracture were made. BERYLLIUM possesses some very attractive properties for general design applications, especially its strength to weight ratio which is approximately twice that of aluminum and three times that of stainless steel. Equally significant, however, is its combination of high moduli , high strength (approximately 70,000 psi tension and 40,000 psi shear), and low density (0.0658 Ib per in.3), which has made it a potentially important structural material for use in high-speed aircraft and missiles. The main attractions of beryllium are most marked when compared to other constructional alloys now in use. For example, while its density is approximateiy that of magnesium, its modulus of elasticity is approximately seven times that of magnesium, three times that of titanium, four times that of aluminum, and 1 1/3 times that of steel. Furthermore, its relatively high strength and high melting temperature permit design for service temperatures to about 1100°F. It is felt by the aircraft industry in general,' that the high cost of beryllium can easily be amortized by the savings in fuel costs, and increases in aircraft payload and range. The only factor which has prevented the use of the metal in structural applications is its lack of sufficient ductility. It is this property that has retarded the development and utilization of beryllium. Beryllium's modes of deformation, Fig. 1 indicate that the main fracture planes at room temperature in a randomly oriented sample are the (0001) basal planes; the (1150) prism planes are the planes of secondary fracture.' Klein, Macres, Woodard, and Greenspan3 obtained elongations of up to 40 pct in beryllium sheet rolled above 700°C when the (0001) basal planes were oriented parallel to the plane of the sheet (see Fig. 2).

Jan 1, 1962

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By P. W. Rainier

The Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyach, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. I), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possibilities for hydroelectric power. The center of population nearest to Chivor is Bogoth, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from BogotB is accomplished by rail to Choconta, some 4 hr. travel. From Choconth the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Choconth costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 130 in. The temperature throughout the year is nearly constant, varying from about 45" F. to about 65" F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1931

By J. Weertman

An explanation is advanced for the recent results of Barrett and Sherby on the high-temperature creep of fee metals. Their measurements indicate that metals with a low stacking fault energy creep at a much slower rate than metals with a high stacking fault energy. The explanation is based on the assumption that the rate of core diffusion is much smaller in partial dislocations than in perfect dislocations. An experiment is suggested to test this assumption. The explanation also requires that the jog density is small on widely split dislocations. SHERBY and Barrett1,2 recently established an important result in the field of high-temperature steady-state creep. They have shown that fee metals whose dislocations split into partial dislocations separated by a wide stacking-fault ribbon creep at a much slower rate than fee metals whose dislocations are not split appreciably. The creep rates in the two cases may differ by a factor as high as 6000. (For the purpose of comparison, the test temperature of each metal was chosen so that its rate of self-diffusion was equal to a standard value. Similarly the stress levels were such that the ratio of the stress to an appropriate elastic modulus was the same for each metal. In all cases the stresses were sufficiently low that the steady-state creep rate was proportional to the stress raised to a power.) It is the purpose of the present paper to attempt an explanation of this interesting and significant result of Sherby and Barrett. The activation energies of high-temperature creep of the metals tested by Sherby and Barrett (aluminum, nickel, copper, and silver) were equal to their self-diffusion activation energies. Hence it appears reasonable to assume that this type of creep is controlled by a dislocation-climb process, which in turn is controlled by the diffusion of vacancies to or from dislocation lines. (It will be assumed that the diffusion of interstitial atoms is unimportant in the climb process. The analysis could be repeated for the case in which interstitial atoms are important.) In prior papers374 I have treated dislocation climb by using the assumptions that core diffusion is extremely fast down a dislocation and that a dislocation always maintains an appropriate vacancy concentration in its immediate vicinity. In this

Jan 1, 1965

By Oscar A. Glaeser

THE mine and plant of the United Verde Copper Co., located in Yav-api County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level. The underground mining operations extend from the 300 to the 3000-ft. level. There are about 45 stopes in active operation on the 17 levels

Jan 1, 1929

By R. C. Craze

This paper discusses the characteristics of the velocity logs now available to the petroleum industry, and some of their advantages and limitations. The velocity log was designed as an aid to the geophysicist to determine velocity layering in the earth and to provide fast, accurate and economical vertical travel time data. After a number of logs had been made, studies were carried out on their use ia correlating strata in adjacent wells. It was found that adjacent strata usually show sufficient velocity contrast to make it possible to correlate these from well to well, even in areas where electric or radioactive logs fail.' In addition, velocity logs have been useful in the determination of porosity and thickness of reservoir rock.' These uses for velocity logs require an understanding of the characteristics of the log in response to the changes in velocity and in borehole conditions encountered normally in logging. GENERAL DISCUSSION OF INSTRUMENTATION The measurement made in velocity logging is more accurately described as a measurement of time rather than velocity. Ideally the log is obtained by measuring the length of time required for compressional sound waves to travel through a fixed distance in the formation. In practice, the time measurement may be made accurately but the distance through which the waves have traveled may vary slightly. Changes in borehole diameter are responsible largely for the difficulty in maintaining a fixed distance, especially if the diameter variations are so abrupt and frequent that the borehole instrument cannot follow contours of the hole. Several service companies have velocity logging equipment available or under development which have different transmitters, receivers, and measuring systems. While these differences are important, there are actually only two systems in use at the present time (Fig. I)."' The first system initiates a pulse at a trans-mitter and detects it at a single receiver. The transmitter and receiver are separated by a fixed distance, called the spacing. The time measured is that between the initiation of the pulse and the first arrival of acoustical energy at the receiver. The second system uses two receivers and a transmitter. The receivers are separated by a fixed distance and the time between arrivals of energy at the two receivers is measured. Here, the spacing is the distance between receivers. The two systems have much in common for it is possible to record both logs simultaneously. Usually the transmitter is an electro-mechanical transducer which produces discrete

By P. W. Rainier

THE Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyacá, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. 1), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possi-bilities for hydroelectric power. The center of population nearest to Chivor is Bogota, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from Bogota, is accomplished by rail to Chocontá, some 4 hr. travel. From Chocontá the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Chocontá costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 150 in. The temperature throughout the year is nearly constant, varying from about 45° F. to about 65° F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1929

By Samuel Daniels

THE Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such con¬dition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400° to 600° F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400° F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600° F., the AI-Cu-Fe-Mg alloy at about 700° F. The former starts to reharden at 700° F., the latter at 800° F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500° and of 700° F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500° and 700° F. Although the latter can be made harder initially than the AI-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. CERTAIN aluminum alloys have been used for pistons and other parts operating at temperatures up to 650° F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance o corrosion. In the piston, the inertia forces and the bearing loading and with this the vibration are decreased. The piston head functions at a lower temperature (about 200° F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design.

Jan 2, 1926

By AIME

Cores must be cut in half to secure workable samples for saturation, porosity, and permeability tests. They come from the field labeled as to the type of core, well, and depth from which they came.

Jan 1, 1948