Search Documents

By John C. Gifford, Charles L. Thomas

A unique and reproducible method is presented for the determination of water vapor in tough pitch wire bar copper. The procedure involves reduction of the water vapor with molten aluminum to form hydrogen, which is subsequently measured by mass spectroscopy. Average water vapor pressures within the porosities of the wire bar samples are calculated. Correlation is to exist between the specific gravities of the samples and their measured water vapor contents. The method should find application as a very sensitive means of detecting hydrogen embrittlement in copper. The nature and quantity of gases evolved and retained during the horizontal casting of tough pitch wire bar copper have long been of interest to the metallurgist. Considerable work has been done at this laboratory on the determination of these gases. The work has involved not only qualitative but also quantitative analysis, so as to provide a basis for a total accounting of the porosity which is associated with the cast product. From a knowledge of the gas-forming elements within the copper, and the practice of melting and protecting it with a reducing flame followed by contact with a charcoal cover in the casting ladle, the gases which one might expect to find in the pores of the cast product are sulfur dioxide, carbon monoxide, carbon dioxide, hydrogen, and water vapor. Hydrogen sulfide, nitrogen, and hydrocarbons would be other possibilities; however vacuum fusion-mass spectroscopy techniques employed at this laboratory have shown that no hydrogen sulfide and only traces of nitrogen and methane are present. It is highly improbable according to phillipsl that any sulfur dioxide could be evolved in wire bar copper with 10 ppm or less sulfur under normal freezing conditions. Mackay and smith2 have noted that porosity due to sulfur dioxide only becomes noticeable at concentrations above 20 ppm S. Investigation of carbon monoxide and carbon dioxide by a variation in the method of Bever and Floe showed that these two gases could only account, at 760 mm and 1064°C (Cu-Cua eutectic temperature), for a maximum of about 25 pct of the total porosity in a wire bar having a specific gravity of 8.40 g per cu cm. phillips' has noted that no normal furnace atmosphere is ever sufficiently rich in hydrogen to cause porosity in copper from hydrogen alone. In addition, using a hot vacuum extraction technique for hydrogen,4 values have never been observed in excess of 10 ppb in tough pitch wire bar. On the basis of the preceding considerations of gases in tough pitch wire bar, only water vapor is left to account for the major portion of the porosity. Direct determinations of water vapor are virtually impossible at low concentrations by any presently known technique, due to adsorption and desorption within the walls of the apparatus used.5 The present investigation deals with a method for the determination of water vapor by an indirect procedure, using molten aluminum as a reducing agent to form hydrogen according to the reaction: 2A1 + 3H2O — A12O3 + 3H2 The evolved hydrogen can then be measured quantitatively by mass spectroscopy. EXPERIMENTAL A 10-g piece of 99.9+ pct A1 was charged into a porous alumina crucible (Laboratory Equipment Co., No. 528-30). Fig. 1 shows the crucible in place at the bottom of an 8-in.-long quartz thimble. A funnel tube with two l1/8-in.-OD sidearms extending at a 90-deg angle from each other was attached to the top of the thimble. One of the sidearms was joined to the inlet system of the mass spectrometer (Consolidated Electrodynamics Corp. Model 21-620A) via a mercury diffusion pump situated between two dry-ice traps. The copper samples were placed in the other sidearm, followed by a glass-enclosed magnetic stirring bar for pushing the samples into the crucible. All ground joints were sealed with vacuum-grade wax. The entire system was evacuated and the aluminum was heated with a T-2.5 Lepel High Frequency Induction Furnace for 21/2 hr at a temperature visually estimated to be 900°C. The temperature was then lowered and the hydrogen was monitored on the mass spectrometer until it was given off at a constant rate of about 4 to 5 1 per hr. This rate corresponded to a slope of 2 to 3 divisions per min on the X3 attenuation of a 10-mv recorder at a hydrogen sensitivity of approximately 100 divisions per 1. A micromanometer (Consolidated Electrodynamics Corp. Model 23-105)

Jan 1, 1969

By R. Wild, F. A. Wright

When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest. In recent years good burden preparation with emphasis on uniformly sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility. This paper explores the Linder method of measuring such reducibility. The measurement of reducibility of burden materials must be carried out under conditions duplicating, as nearly as possible, those of the blast furnace stack. This is very difficult since the blast furnace process is a counter-current one, and thus the initial conditions encountered by the solid (gas temperature, composition, etc.) are the result of heat and mass transfer occurring lower down the stack. Any method of burden testing which does not take this into account is, at least to some extent, based on arbitrary assumptions. In an attempt to study blast furnace reactions under non-arbitrary conditions BISRA adopted the SCICE technique as a method of investigation. This technique has been used with a measure of success.' The SCICE technique, however, was found to be too slow for use as a routine test for burden materials and it was decided to construct additional equipment for burden testing. A test was required which would: 1) Be as realistic as possible. 2) Be quick and easy to operate. 3) Give some indication of the breakdown likely to take place during reduction in addition to a reducibility index. After a critical assessment of the reducibility tests which have been proposed it was decided to adopt the Linder test equipment and procedure as a basis for burden testing. THE LINDER TEST APPARATUS AND PROCEDURE The apparatus which was constructed (Fig. 1) was the same as that described by Linder2 except for minor changes in design. Linder also laid down a test procedure which he had derived from the results of investigations on Swedish blast furnaces. The variations of temperature and gas composition during the test were defined; these are shown diagram-matically in Fig. 2. BISRA's intention was to use the standard temperature and gas composition programmes for testing a variety of burden materials and also to investigate the influence of different programmes on standard burden materials, making use of information from the SCICE apparatus wherever this is possible. Up to the present, effort has been concentrated on the first part of the programme, and work on the second part has only just commenced. For each test 200 g of coke and 500 g of burden material were used. Linder had recommended that the coke and burden material should be between 1 and 1 1/2 in. and this was adhered to in early experiments on ores and sinters. Since the eventual aim of this work was to relate the test results to blast furnace operation, it was decided to carry out subsequent experiments using burden material in the size range used in the blast furnace, as far as this was possible. If the main interest was, for example, a comparison of the products resulting from different methods of agglomeration, then there would be advantages in using burden materials as close as possible to a standard size. After the charge had been placed in the reaction tube and this had been connected to the gas supply, rotation of the reaction tube at 30 rpm was started and the reduction programme was commenced, the gas temperature and composition being manually controlled according to the programme shown in Fig. 2. After the reduction test the charge was cooled in a nitrogen atmosphere. It was then removed from the reaction tube, the coke and burden separated, and the extent of burden breakdown assessed by screening it at 10 and 30 mesh. The extent of reduction was then

Jan 1, 1964

ARTICLE I Name and Object Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the field of physical metallurgy; that is, the nature, structure, alloying, fabrication, heat treatment, properties and uses of metals; to represent the AIME insofar as physical metallurgy is concerned, within the rights given in AIME Bylaw, Article XI, Sec. 2, and not inconsistent with the Constitution and Bylaws of the AIME; to hold meetings for the discussion of physical metallurgy; to stimulate the writing, publication, presentation and discussion of papers of high quality on physical metallurgy; to accept or reject papers for presentation before meetings of the Division. ARTICLE II Members Sec. 1. Any member of the AIME of any class and in good standing may become a member of this Division upon registering in writing a desire to do so, but without additional dues. Sec. 2. Any member not in good standing in the AIME shall forfeit his privileges in the Division. ARTICLE III Funds Sec. 1. The expenditure of the funds received by the Division shall be authorized by the Executive Committee of the Division. ARTICLE IV Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the AIME, and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the AIME. Sec. 2. The annual business meeting shall be held within a few days before or after the annual business meeting of the AIME. Sec. 3. At a meeting of the Division, for which notice has been sent to the members of the Division through the regular mail or by publication in the Journal of Metals at least one month in advance, a business meeting may be convened by order of the Executive Committee and any routine business transacted not inconsistent with these Bylaws or with the Constitution or Bylaws of the AIME. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. ARTICLE V Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, a Senior Vice-Chairman, a Vice-Chair -man, a Secretary and a Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, insofar as is consistent with the Bylaws of the Division and the Constitution and Bylaws of the AIME. Sec. 3. The Executive Committee shall consist of the Chairman, Senior Vice-Chairman, Vice-Chairman, past Chairman, Secretary, and nine members, all of whom shall be nominated and elected as provided hereafter in Article VII. Sec. 4. The Chairman, Senior Vice-Chairman and Vice-Chairman shall serve for one year each, or until their successors are elected. Each member of the Executive Committee shall serve three years. The Chairman shall remain a voting member of the Executive Committee for one year after his term as Chairman. Sec. 5. The Treasurer of the Division shall be invited to meet with the Executive Committee, but without ex-officio right to vote. He shall be appointed annually by the Executive Committee, from the membership of the Executive Committee or otherwise. Sec. 6. The annual term of office for officers of the Division shall start at the close of the Annual Meeting of the Institute and shall terminate at the close of the next Annual Meeting. ARTICLE VI Committees Sec. 1. There shall be standing committees as follows: Programs Committee. Finance Committee, Membership Committee, Annual Lecture Committee, Technical Publications Committee, Mathewson Gold Medal Committee, Nominating Committee, Education Committee and such other Committees as the Executive Committee may authorize. Sec. 2. It shall be the duty of the Programs Committee to secure the presentation of papers of appropriate character at meetings of the Division. Sec. 3. It shall be the duty of the Finance Committee to inquire into and examine the financial condition of the Division and to consider proper means of increasing its revenue and limiting its expenses. The Finance Committee shall audit the accounts of the Division and report to the Executive Committee prior to the Annual Meeting of the Division. It shall render a budget to the Executive Committee estimating receipts and expenses for the ensuing year so that action can be taken on same at the first meeting following the Annual Meeting.

Jan 1, 1953

By R. Schuhmann, J. Th. Overbeek, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.'-" Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles. The contact angle is a complex quantity because the properties of three different phases, or rather of three different interfaces, control its magnitude. Considering the interfaces close to the region of ternary contact to be plane, the relation among the contact angle and the three binary interfacial tensions is easily derived. The condition for equilibrium among the three surface tensions, Fig. 1, or the requirement of minimum total surface free energy leads to Young's equation, Eq. I: ysa — ysl = yLA cos 0 [1] According to this equation, the contact angle has one well-defined value. Actually it is found in many experiments that the value of the contact angle depends on whether the air is replacing liquid over the solid (receding angle) or the liquid is replacing air (advancing angle). The receding angle is always the smaller of the two.4 Two explanations have been offered for this experimental fact. According to some investigators,5-8 roughness of the surface causes apparent contact angles that are different for the receding and the advancing cases although the actual local contact angle may be completely determined by Eq. 1. The other explanation involves the hypothesis that the solid-air interface after the liquid has just receded is different from the same interface when no liquid has previously covered it.1,4 Adsorption of constituents of the air or liquid might play a role here. In this discussion the difference between advancing and receding contact angle will be neglected and plane surfaces where Eq. 1 describes the situation will be considered. But there is still a fundamental obstacle to the application of Young's equation. The surface tension of the liquid (rla) can easily be determined, but the two surface tensions of the solid (rsa and ySL) cannot be measured directly. Eq. 1, however, is not without value. By contact angle measurements it is possible to establish how ysl — ysl varies with the addition of solutes to the liquid phase. Also, Eq. 1 affords a convenient starting point for calculating net forces and energy changes involved in the process of bubble-particle attachment.1,2 . If for the moment surface tension of the liquid (yLa) is considered a constant, an increase in ysa — ysL, will tend to decrease the contact angle. A decrease in ySA — ysl, corresponds to an increase of the contact angle. In cases where ySA — ySL > yLa the contact angle is zero; it will only reach finite values when ysa — ysa has been decreased below YLA. Thus on the basis of Young's equation and contact angle measurements alone, it can be learned how flotation reagents affect the difference Ysa — ysl, but no conclusions can be drawn as to the effects of reagents on the individual surface tensions ysa, and ysL, not even as to signs or directions of the surface tension changes resulting from reagent additions. A quantitative relationship between the surface tension or interfacial tension and the adsorption occurring at a surface or an interface is given by the Gibbs equation, which for constant temperature and pressure reads dy = — 2 T, du, [2] where dy is the infinitesimal change in surface tension accompanying a change in chemical potential

Jan 1, 1955

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By J. F. Smith, J. E. Davison

The heat capacity of CaMg2 was measured over the temperature interval, 4.8° to 287°K, by the technique of low-temperature adiabatic calorimetry. Heat content measurements were performed with a drop calorimeter over the temperature interval, 273" to 673°K. From these data the thermodynamic functions, (FT - H0)/T, ST - So, and & - Ho, were evaluated. A third-Law calculation of the standard entropy of formation of CaMg2 yields a value of -0.25 * 0.06 cal per (°K g-atom) , and the free-energy function derived from this study when combined with existing equilibria data yields a value for the standard enthalpy of formation which is in agreement with direct calorimetric enthalpy measurements. The accompanying paper' shows that the enthalpy of formation of CaMg2 has been determined with good precision by three different calorimetric techniques.'-= TWO independent determinations of the Gibbs free energy of formation of CaMg2 have also been made; both determinations were based on vapor pressure measurements, being in one case hydrogen vapor pressures over ternary Ca-Mg-H alloys4 and in the other case magnesium vapor pressures over binary Ca-Mg alloys.5 The present determination of heat capacity of CaMg2 below room temperature and of the heat content of CaMg2 above room temperature was undertaken to provide supplementary data. These data are useful in their own right but can in addition be used to evaluate an entropy of formation for CaMg2 which, because of the interrelation of free energy, enthalpy, and entropy, can be used as a check of the self-consistency of the composite of the presently available information. LOW-TEMPERATURE HEAT CAPACITY The heat capacity of CaMg2 was measured over the temperature interval 4.87° to 286.64°K in an adiabatic calorimeter. The physical details of the calorimeter and the experimental procedure for measuring the heat capacity of a specimen have been adequately described by Gerstein et a1.6 The source and purity of the calcium and magnesium are described together with the methods of sample preparation and chemical analyses in the accompanying paper.' Results of chemical analyses of the material which was used in the present investigation are shown in Table I. These analyses show that, on the basis of the published phase diagram,7 the heat capacity sample contained a slight excess of a calcium while the heat content sample contained a slight excess of magnesium. However, in both cases the excess was small, and X-ray diffraction patterns showed reflections which were without exception attributable to CaMg2. The sample which was used for heat capacity measurements weighed 69 g while the sample container and addenda weighed 132 g. The sample was in the form of annealed powder, 50 to 60 mesh, and was sealed into the sample container under 0.1 atm of helium. Copper fins inside the sample container facilitated thermal equilibrium of the powdered Sample. Time intervals of the order of 10 min were required for thermal equilibration, and such times are normal for this calorimeter regardless of the form of the sample. The observed heat capacities were corrected for the small excess of a calcium through use of the heat capacity values tabulated by Hultgren et a1.8 The corrected heat capacities are tabulated as a function of temperature in Table II. The free-energy function and the absolute entropy of CaMg2, which were calculated from the experimental heat capacity data, are listed in Table 111. A smooth curve was fitted to a plot of the experimental values of the heat capacity and in only two instances above 30°K did the plotted points deviate from the curve by more than 0.2 pct. Below 10°K the deviation of several of the points was as much as 50 pct. These large percentage deviations were attributed to the small value of the heat capacity and to the low sensitivity of the platinum resistance thermometer in this temperature range. The deviations in the region of 10°to 30°K were less than 5 pct. Although the percentage deviations of some of the low-temperature measurements are large, the actual value of these deviations is small since the magnitude of the heat capacity in that temperature range is small. The error in the value of the third-law entropy at 298.15°K was estimated to be less than 0.01 cal per (°K g-atom). A value of -0.25 ±0.06 cal per (°K g-atom) was obtained for the standard entropy of formation at 298.15°K from the relation:

Jan 1, 1969

By S. L. Craig, C. Orr, H. G. Blocker

WITHIN recent years gas adsorption methods have been developed for measuring the surface area of finely divided materials and have become extremely valuable in research on the corrosion and the catalytic activity of metals. Rather elaborate apparatus is required, and a single determination is so time-consuming that these methods have not been utilized to the fullest extent; the methods are un-suited for most routine control work such as that encountered in powder metallurgical operations and in processes employing metal catalysts. These difficulties are largely eliminated, and surface area is reduced to a routine determination if the liquid-phase adsorption of a surface-active agent such as a fatty acid can be used. When the affinity of the fatty acid carboxyl group for the solid surface is greater than its affinity for the solvent, a unimolec-ular layer of orientated fatty acid molecules will be formed at the solid-liquid interface in a manner similar to that of a compressed fatty acid film on a water surface. The measurement of surface area is then reduced to a measurement of fatty acid adsorption. This propitious circumstance, first investigated by Harkins and Gans,¹ has been employed with somewhat inconclusive results by a number of investigators in evaluating the surface properties of metals, metal catalysts, and metal oxides. The specific surface area values for nickel and platinum catalysts, determined from the adsorption of a number of fatty acids from various solvents, were found by Smith and Fuzek² to agree with values calculated by the gas adsorption technique of Brunauer, Emmett, and Teller," he so-called BET technique. And recently Orr and Bankston4 have also reported good agreement between nitrogen gas and stearic acid adsorption results in the measurement of the surface areas of clay materials. On the other hand, Ries, Johnson, and Melik5 found only order-of-magnitude agreement between these two methods in studying supported, cobalt catalysts having specific surface areas as great as 420 sq m per g; the reason is partially attributable to the very porous nature of the materials. Greenhill,6 investigating the adsorption of long-chain, polar compounds in organic solvents on a number of metal powders, concluded that a uni-molecular layer of stearic acid was formed on exposure of the solid to the acid solution and that the presence of an oxide or another film did not alter this result. Furthermore, the adsorption process appeared to be the same whether or not the sample was degassed prior to exposure to the solution. Greenhill estimated the surface area of one of the powders he investigated from microscopic diameter measurements, and obtained a rough check with surface area evaluation. Russell and Cochran7 found moderate agreement for alumina surface area results by fatty acid and gas adsorption methods. In addition, they also found that the prolonged heating and evacuating pretreatments previously used by investigators were unnecessary. The present work, however, considerably extends these previous investigations, shows that fatty acid adsorption can be used to determine the surface area of a variety of metals and metal compounds, offers further confirmation of the correctness of gas adsorption methods, and presents a simplified technique for the determination of the metal surface area which is suitable for routine work. Experimental Technique Basically, the fatty acid adsorption method is quite simple. It consists of exposing a sample of the material of which the surface area is desired to a fatty acid solution of known concentration. By analysis of an aliquot of the solution, the concentration after adsorption has occurred may be determined. The difference between the initial quantity of acid in solution and the final quantity is that quantity of acid adsorbed by the sample. The specific surface area of the adsorbent material may be calculated from the quantity adsorbed and the weight of the sample. In agreement with the findings of others as outlined above, it was found entirely unnecessary to degas or pretreat the nonporous materials employed other than by drying them thoroughly. However, precaution was necessary so that the dried sample entered the fatty acid solution with little exposure to moisture. The effect of moisture on the interaction of stearic acid with finely divided materials has been thoroughly investigated by Hirst and Lancaster." They found the presence of water merely reduced the amount of acid adsorbed by powders such as TiO2, SiO2, Tic, and Sic. With reactive materials such as Cu, Cu2O, CuO, Zn, and ZnO, however, water was found to initiate chemical reaction. Only with ZnO was reaction observed when the solid and the solu-

Jan 1, 1953

By R. W. Stormont, F. Wald

The phase diagram of the Pseudobinary section PbTe-Fe was determined. It was found to contain a monotectic and a eutectic reaction, the latter one taking place at 14 at. pct Fe and 875° * 5°C. The solid solubility of iron in PbTe was found to be 0.3 at. pct by electronmicroProbe analysis. No solubility of PbTe was detected in iron. Slight deviations from true pseudobinary behavior were found to occur in the range of - 5 to 10 at. pct Fe. In the course of a general investigation of reactions of various metals with lead and tin telluride,' the lead telluride-iron system was reinvestigated. It had been established much earlier than iron does not chemically react with lead telluride but forms a eutectic with a melting point of 879" The eutectic composition or other related information has never been reported, but for a number of years iron has been in general use for contacting of lead telluride and lead telluride alloys for thermoelectric applications. It seems therefore desirable to clarify the exact constitution of the system to furnish a base for the long-term evaluation of bonds made between lead telluride and iron either by pressure contacting or by brazing methods. I) EXPERIMENTAL METHODS Lead telluride-iron alloys were prepared in 10-g charges, using premelted lead telluride. This material was prepared from high-purity, semiconductor-grade lead and tellurium obtained from the American Smelting and Refining Co. and described as 99.999 pct pure. The iron used was "Armco" iron; the major impurities found here were 0.02 pct C, 0.018 pct Si, and 0.015 pct Cr. All remaining impurities were less than 0.01, the total of all impurities not exceeding 0.15 pct. Charges were prepared in closed quartz arnpoules which were evacuated and in some cases backfilled with high-purity argon to retard excessive lead telluride evaporation and deposition in slightly cooler parts of the ampoule. For high iron concentrations, this can lead to total separation of the constituents, since the vapor pressure and the sublimation rate of PbTe are quite high.4 Nevertheless, since the ampoules are closed, no change in overall composition was expected and the nominal composition of all alloys was assumed to be retained. X-ray diffraction analysis, thermal analysis, and microsections were used in the evaluation of the alloys. The nature of the system was such that X-ray diffraction was not particularly helpful. It merely served to establish that at all concentrations PbTe and a! iron were in equilibrium at room temperature. Thermal analysis was carried out by taking direct temperature vs time curves on a Sargent recorder where a width of 10 in. was kept as 1 or 0.5 mv by use of an automatic bucking voltage network. Quartz ampoules with minimized dead space, coated with boron nitride and fitted with a thermocouple reentrant, were used as containers for the charge. At high temperatures and over long periods of time, boron nitride reacts with iron. For the thermal analysis runs, however, this was not significant. More significant was the fact that the vapor pressure of PbTe at some of the meas -uring temperatures apparently exceeded I atrn quite considerably. This, in some cases, caused the slightly softened quartz tubes to blow out if great care was not taken to contain them and minimize time and temperatures used. As containers pure nickel tubes were used which also served to avoid temperature gradients in the quartz ampoule. Nevertheless, the experimental difficulties at high temperatures were severe and the monotectic temperature could therefore not be determined accurately. In general, the accuracy reached by the thermal analysis setup in this case is *4"C as determined with gold, silver, and tin, under the conditions of analysis here. Inherently, the apparatus is capable of reaching accuracies better than i 1°C. Also, difficulties were encountered in microsection-ing. They were related to polishing, since it is rather difficult to avoid pulling the iron out of the weak and brittle lead telluride matrix. It proved best to follow a procedure where, after grinding to 600 grit on carborundum paper, a polish with 6 p diamond was used on nylon cloth. Finally, #3 "Buehler" alumina and an automatic polisher were used for -5 min only, to avoid relief. The best etching results were achieved with

Jan 1, 1969

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed. Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank, or at any time in batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume1,2 or a relative concentration, which will be a function of the recovery." A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the data. One of these, the initial concentration or proportion of floatable mineral, is not necessarily equal to the feed assay because of nonfloatable oversize or locked particles." The other, a rate constant, is a measure of proportionality between the rate and the pulp property on which the rate depends. The value of the rate constant will be determined by the values of all variables which control the process and will be changed by significant changes in any of them. It is, therefore, a direct measure of performance. Where recovery or grade change continuously with flotation time, the rate constant will be independent of time and will characterize the entire course of the separation. Development of Rate Equations Rate equations can be developed either by analysis of the mechanism of the process or by direct fitting of equations to recovery-time data. Sutherland's attempt by the first method' suggests that the effect of particle size variation on the rate complicates the derivation of a simple equation applicable to an ore pulp. A further problem with an ore is the concentrate grade requirement, which usually involves a variable rate of froth removal. Thus the final rate for any cell may depend on the froth character and froth height, as well as on the pulp composition. This does not imply that each cell cannot reach a steady state2 in which the rate will depend ultimately on pulp composition. The second method is the fitting of rate equations consistent with the necessary boundary conditions* to experimental recovery-time curves. On the assumption that under constant operating conditions the flotation rate is proportional to the actual or relative concentration of floatable mineral in the pulp, a generalized rate equation may be expressed as follows: Rate = Kcn [I] where K is the rate constant, c is some measure of the quantity of floatable mineral in the pulp at time t, and n is a positive number. In previous rate studies, the value of n has been taken as 1, either by direct assumption," or as a result of the hypothesis that bubble-particle collision is rate determining.' A first order equation results, which after integration in terms of cumulative recovery R, leads to Loge A/A-R = Kt [2] The quantity A is the maximum possible recovery with prolonged time under the conditions used. No conclusive proof for the validity of this equation in flotation has been advanced. The evidence cited in its support consists entirely in the demonstration that it appears to apply to a limited number of recovery-time curves."' It will be shown subsequently that this procedure is not sufficient to establish the order of a flotation rate equation. The possibility that the equation may be of higher order therefore requires examination. If, in particular, the exponent in eq 1 is assumed to be 2, then after integration there results R = A2Kt/1 + AKt [3] with K again a rate constant and A the maximum proportion of recoverable mineral. Eq 3 may be

Jan 1, 1952

By R. H. Walpole, J. M. Kane

IN all probability the mining and metallurgical industry as a whole can demonstrate a larger ecorlomic return from installation of dust-control equipment than any other major industrial group. This fact has partially accounted for the marked increase of dust-control installations made during the past decade. While the primary objectives for installation of dust-collecting systems are improved working and operating conditions for men and equipment, the fact that an economic return can be anticipated on salvageable materials is an added advantage which shows in partial or complete equipment write-off. The conditions apply to most phases of the mining, milling, and smelting industry, both non-metallic and metallic. As with any mechanical devices, selection of suitable dust collector equipment involves evaluation of available products with characteristics most nearly meeting conditions of the application at hand. When there is valuable product to be collected, and/or when there are possibilities of air pollution or public nuisance, collector selection is often guided by the maxim of "highest available collection efficiency at reasonable cost and reasonable maintenance." A brief review of dust collector designs will permit outlining of major characteristics of each group. Final selection will involve detailed data against a background of the problem under consideration. The dry centrifugal collectors, see Fig. 1, represent a group of low cost units with minimum maintenance. They are subject to abrasion under heavy abrasive dust loads and to plugging with moist materials. Efficiency drops off rapidly on particle sizes below the 10 to 20 micron group. Because of the large amounts of —10 micron particles in most mining dust problems, they will normally be used as primary collectors and will be followed by high efficiency units. This combination is cspecially popular where the bulk of material is desired in a dry state with wet collection indicated for the final cleanup portion. In remote plant locations, dry centrifugal~ can be used alone if product in dust form has no value or if dust loading is light enough to eliminate a nuisance in the plant area. Where high efficiency dust colleotion equipment must be selected, choice will normally involve fabric arresters, wet collectors, or high voltage Electro-Static precip-itators. Fabric arresters, see Fig. 2, rely on the passing of dust-laden air at low velocity through filter fabric. Velocity ranges from 1 to 3 fpm for the usual installation and may be as high as 10 to 20 fpm in arrangements where automatic frequent vibration or continuous cleaning of the filter media is employed. Fabric is normally suspended in either stocking type or in an enlvelope shape. Collection efficiency is excellent even on sub-micron particle sizes. Equipment is bulky, must be vibrated to remove the collected dust load, and is restricted in applications from temperature and moisture standpoints. Condensation of moisture on the fabric filter mcdia causes plugging of the passages with great reduction in air flow. Temperatures for the usual medias of cotton or wool are 180" and 200°F maximum, although the introduction of synthetic materials such as nylon, orlon, and glass cloth have increased the possibilities of this type of collector for higher temperature applications. The wet-type collector may employ a number of different principles so that entering dust particles in the gas stream are wetted and removed. Principles usually include impingement on collector surface or water droplets, often in combination with centrifugal forces. Variety of wet collector designs is indicated by typical collectors illustrated in Figs. 3 and 4. Collection efficiency is a function of the particular design, although the better collectors will have high collection efficiency on particles in the 1-micron range. Wet collectors have the advantage of handling hot or moist gases, take up small space, and eliminate secondary dust problems during the disposal of the material. At times collection of the material wet is a disadvantage. Wet collectors may also be subject to corrosion and freezing factors. The high voltage Electro-Static precipitator, see Fig. 5, is probably the most expensive type of high efficiency collector. It finds its applications generally in problems in which collectors previously discussed cannot be employed. Its collection efficiency is based on its design features and can be excellent on the finest of fume particles. Material is normally collected dry. Gas temperatures are of no great concern as long as condensation does not occur within the dry type of precipitator and the temperatures do not exceed the limits for materials used in its construction. As with the fabric arrester, provisions

Jan 1, 1954

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By R. M. Leibrock, J. E. Huzarevich, R. G. Hiltz

The various factors considered in recommending the initiation of a gas injection project in the southern portion of the Cedar Lake Field are discussed. Performance history under gas injection operations is reviewed and these data are analyzed, utilizing both the material balance method and the fractional flow and frontal advance expressions. Results of the analysis of the performance data indicate that the injected gas has contacted and affected at least 60 per cent of the reservoir and a substantial increase in ultimate recovery can reasonably be expected. By holding the reservoir pressure appreciably above the bubble point, the well productive capacities have been maintained substantially above the level predicted for primary operations. The analysis of the Cedar Lake project suggests that in certain limestone reservoirs, at least, the probable success of gas injection cannot be predicted simply from ohservation of permeability distribution throughout the pay section, as indicated by core analysis data, on either one or a number of wells. Further, the performance of this particular project fails to indicate any basis for classifying carbonate reservoirs in general as being inherently unsuited to a dispersed type gas injection program, thus indicating that each reservoir should be considered on its own merits, regardless of the composition of the reservoir rock. INTRODUCTION Early in the life of the Cedar Lake Field, an extensive data gathering program was initiated to provide an accurate record of reservoir performance characteristics. From the study of these data it was apparent that there was a critical need for supplementing the natural reservoir energy in order to maintain well productivities and obtain the maximum ultimate oil recovery. Accordingly, detailed engineering studies were made of the various methods of secondary recovery which might be applicable. As a result of these investigations, the decision was made to initiate a gas injection program of sufficient intensity to maintain reservoir pressure at approximately 600 psia, or some 274 lb above the bubble point pressure of 326 psia. A full scale dispersed type gas injection program has been in operation on leases of the Stanolind Oil and Gas Co. in the southern portion of the field for nearly five years, and sufficient performance data are now available to evaluate the benefits which have been derived from this project. It is the primary purpose of this paper to analyze the performance data for the Cedar Lake gas injection project and to point out the significance of the ohserved behavior with respect to certain hypotheses which have been advanced in recent years concerning the probable success of gas injection projects in limestone reservoirs. This paper properly should be regarded more on the order of a progress report, inasmuch as some revision in interpretation will undoubtedly be required from time to time as additional performance data are obtained, although the satisfactory performance of the project to date leaves little doubt as to the ultimate success of gas injection in the Cedar Lake Field. As a result of the success of the project to date, a unit was formed in the southern part of the field, effective March 1, 1951, for the purpose of continuation of the gas injection program. Participants in this unit are the Mid-Continent Petroleum Co. and Stanolind Oil and Gas Co. GEOLOGY AND STRATIGRAPHY The Cedar Lake Field is located in the northern portion of the Midland Basin area as shown in Fig. 1. The southwest portion of the field lies within a playa, or dry salt lake, which covers an area of approximately eight square miles. As might be expected, it was this lake which furnished the inspiration for the name of the field. Except for its value as a salt water disposal pit, this lake has succeeded only in magnifying the difficulties in developing this portion of the field. Typical of this section of West Texas, the area in general is relatively flat and has a semi-arid climate. The localized structure which favored the accumulation of oil is an anticline with approximately 100 ft of closure. The major axis of the structure extends in a general southeast-northwest direction. Originally this structure was defined by seismograph data, which have been subsequently confirmed by development. In general, the geologic column is typical of that found throughout the basin. From the surface to depth of approximately 1,800 ft, surface sands and undifferentiated red beds. probably Triassic. are encountered. Below this point to the producing horizon, all formations are of the Permian age.

Jan 1, 1951

By J. E. Huzarevich, R. M. Leibrock, R. G. Hiltz

The various factors considered in recommending the initiation of a gas injection project in the southern portion of the Cedar Lake Field are discussed. Performance history under gas injection operations is reviewed and these data are analyzed, utilizing both the material balance method and the fractional flow and frontal advance expressions. Results of the analysis of the performance data indicate that the injected gas has contacted and affected at least 60 per cent of the reservoir and a substantial increase in ultimate recovery can reasonably be expected. By holding the reservoir pressure appreciably above the bubble point, the well productive capacities have been maintained substantially above the level predicted for primary operations. The analysis of the Cedar Lake project suggests that in certain limestone reservoirs, at least, the probable success of gas injection cannot be predicted simply from ohservation of permeability distribution throughout the pay section, as indicated by core analysis data, on either one or a number of wells. Further, the performance of this particular project fails to indicate any basis for classifying carbonate reservoirs in general as being inherently unsuited to a dispersed type gas injection program, thus indicating that each reservoir should be considered on its own merits, regardless of the composition of the reservoir rock. INTRODUCTION Early in the life of the Cedar Lake Field, an extensive data gathering program was initiated to provide an accurate record of reservoir performance characteristics. From the study of these data it was apparent that there was a critical need for supplementing the natural reservoir energy in order to maintain well productivities and obtain the maximum ultimate oil recovery. Accordingly, detailed engineering studies were made of the various methods of secondary recovery which might be applicable. As a result of these investigations, the decision was made to initiate a gas injection program of sufficient intensity to maintain reservoir pressure at approximately 600 psia, or some 274 lb above the bubble point pressure of 326 psia. A full scale dispersed type gas injection program has been in operation on leases of the Stanolind Oil and Gas Co. in the southern portion of the field for nearly five years, and sufficient performance data are now available to evaluate the benefits which have been derived from this project. It is the primary purpose of this paper to analyze the performance data for the Cedar Lake gas injection project and to point out the significance of the ohserved behavior with respect to certain hypotheses which have been advanced in recent years concerning the probable success of gas injection projects in limestone reservoirs. This paper properly should be regarded more on the order of a progress report, inasmuch as some revision in interpretation will undoubtedly be required from time to time as additional performance data are obtained, although the satisfactory performance of the project to date leaves little doubt as to the ultimate success of gas injection in the Cedar Lake Field. As a result of the success of the project to date, a unit was formed in the southern part of the field, effective March 1, 1951, for the purpose of continuation of the gas injection program. Participants in this unit are the Mid-Continent Petroleum Co. and Stanolind Oil and Gas Co. GEOLOGY AND STRATIGRAPHY The Cedar Lake Field is located in the northern portion of the Midland Basin area as shown in Fig. 1. The southwest portion of the field lies within a playa, or dry salt lake, which covers an area of approximately eight square miles. As might be expected, it was this lake which furnished the inspiration for the name of the field. Except for its value as a salt water disposal pit, this lake has succeeded only in magnifying the difficulties in developing this portion of the field. Typical of this section of West Texas, the area in general is relatively flat and has a semi-arid climate. The localized structure which favored the accumulation of oil is an anticline with approximately 100 ft of closure. The major axis of the structure extends in a general southeast-northwest direction. Originally this structure was defined by seismograph data, which have been subsequently confirmed by development. In general, the geologic column is typical of that found throughout the basin. From the surface to depth of approximately 1,800 ft, surface sands and undifferentiated red beds. probably Triassic. are encountered. Below this point to the producing horizon, all formations are of the Permian age.

Jan 1, 1951

By John C. Sawyer

The mechanism of catastrophic oxidation of chromium and 446 stainless steel is examined. Data are presented to show that accelerated oxidation of these two materials, as caused by lead oxide, can occur in the absence of a liquid layer contrary to presently accepted theory. An alternate theory is proposed in which the rate of accelerated oxidation is a function of the rate at which lead oxide destroys the protective oxide formed on the base metal. An example of the application of the theory is given for the catastrophic oxidation of chromium in the presence of lead oxide. WHEN stainless iron-, nickel-, or cobalt-base alloys are heated in air to moderate temperatures in the presence of certain metallic oxides, oxidation will proceed at an accelerated rate. This phenomenon, often called "catastrophic oxidation", is most pronounced for the stainless steels. With these alloys the condition is so severe that large masses of oxide will form on the surface of the alloy in 1 hr or less at temperatures of 1200o to 1700oF. While a number of oxides are known to cause this effect, PbO, V2O5, and Moo3 are the most familiar, having been the subject of one or more investigations which have appeared in the literature.1-7 In presenting the results of these investigations, many of the authors have offered possible explanations to account for the more rapid rate of oxidation observed; however, the liquid layer theory as proposed by Rathenau and Meijering 2 has been the most commonly accepted mechanism. The liquid layer theory proposes that a low-melting oxide layer is formed on the surface of the alloy as the result of the interaction of the alloy oxide and the contaminating oxide. When the temperature of oxidation is above the melting point of the oxide on the surface, a liquid layer will form and oxidation will proceed at an accelerated rate. At temperatures below the melting point of the surface oxide, oxidation will proceed more slowly in the normal manner. It is argued that the rates of diffusion of oxygen and metal ions through the liquid layer are extremely rapid thereby accounting for the high rate of oxidation. Various experimental data have been presented to show that the temperature at which accelerated oxidation first becomes apparent coincides with the melting point of the eutectic oxide which would be present on the surface. Some exceptions have been observed, e.g., silver will oxidize in the presence of Moo3 at temperatures below the lowest melting eutectic; on the other hand, stainless steel will not be catastrophically oxidized at 1500oF in a molten bath of PbO and SiO2. In reviewing the various theories which have been used to explain catastrophic oxidation, Kubaschewski and Hopkins 8 favor the liquid layer theory, but note that, ".. .as experimental observations are not altogether in agreement with this theory (liquid layer theory), one should consider it a necessary but not a sufficient condition." In contemplating the liquid layer theory, it appears that sufficient evidence has not been presented to establish the theory beyond question. As a means of further clarification, a program of research was undertaken to determine in greater detail the mechanism of accelerated oxidation as caused by lead oxide. The first part of the program deals with a comparison of the oxidation of both AISI 446 stainless steel and chromium metal in the presence of lead oxide, vs the oxidation of these two materials in air alone. These comparisons are made at a number of different temperatures, most of which are below the melting point of the surface oxides. The second part of the program is concerned with a presentation of an alternate theory of accelerated oxidation exemplified by the system Cr-PbO-Air. PROCEDURE AND RESULTS Several experimental methods are commonly used to follow the progress of oxidation. One of these, the weight-gain method, was chosen for this work. This procedure requires that a specimen of the alloy be weighed, oxidized for a given period of time at an elevated temperature, and reweighed—the difference between the two weights being noted. The weight gain of the specimen represents the amount of oxygen acquired from the atmosphere to transform a portion of the specimen to oxide. In those cases where there is a tendency for the specimen or oxide to volatilize at the testing temperature, additional data must be collected so that a correction factor can be determined. This factor must be applied to the weight change in order to ascertain the actual amount of oxidation which has taken place. The specimens used for this work were 1 1/2 in.

Jan 1, 1963

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.' Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By J. T. Norton, Joseph Gurland

IN spite of the extended use and high state of practical development of the cemented tungsten carbides, the structure of these alloys is still a matter of considerable controversy. The characteristic high rigidity and rupture strength of sintered compacts have been attributed to a continuous skeleton of tungsten carbide grains, formed during the sintering process. This view is based mainly on the work of Dawihl and Hinnuber,1 who reported that a sintered compact of 6 pct Co maintained its shape and some of its strength after the binder was leached out with boiling hydrochloric acid. After leaching, only 0.04 pct Co was reported to remain in the compact. They also showed that the assumed increasing discontinuity of such a skeleton, as the cobalt content is increased, could be made to account for the observed discontinuous increase of the coefficients of thermal expansion, the loss of rigidity, and the impaired cutting performance of alloys of more than 10 pct Co. Contradictory evidence was cited by Sanford and Trent,' who mentioned that a sintered compact was destroyed by reacting the binder with zinc and leaching out the resulting Zn-Co alloy. The skeleton theory also does not account for the observed change of strength of sintered compacts as a function of cobalt content. If the skeleton is responsible for the strength, the latter would be expected to decrease with increasing binder content. Actually, the strength increases and reaches a maximum around 20 pct Co. In addition, tungsten carbide is brittle and undoubtedly very notch sensitive. The highest value found in the literature for the transverse rupture strength of pure tungsten carbide prepared by sintering is 80,000 psi.3 herefore, such a skeleton does not easily account for a rupture-strength value of 300,000 psi and higher, commonly found in sint.ered tungsten carbide-cobalt compacts. In view of the conflicting data present in the literature, experiments were undertaken to determine whether the sintering of tungsten carbide-cobalt alloys leads to the formation of a carbide skeleton or whether the densification behavior and the properties of cemented compacts are consistent with a structure of isolated carbide grains in a matrix of binder metal. The specimens were prepared from powders of commercial grade. Tungsten carbide powder ranged in particle size from 0 to 5x10-4 cm. Mixtures of tungsten carbide and cobalt were ball milled in hexane for 48 hr in tungsten carbide lined mills. After milling, the specimens were pressed in a rectangular die (1x1/4x1/4 in.) at 16 tons per sq in. NO pressing lubricant was used. Sintering of the tungsten carbide-cobalt compacts was carried out in a vertical tube furnace equipped with a dilatometer (Fig. I), by means of which the change of length of the powder compacts could be followed from room temperature to 1500°C. An atmosphere of 20 pct H, 80 pct N was maintained inside the furnace. Decarburization of the samples was prevented by the presence of small rings of graphite inside the furnace tube. The temperature of the sample was measured by a platinum-platinum-rhodium thermocouple, which also was part of a temperature control system able to maintain a constant temperature within ±100C. Pure tungsten carbide compacts were prepared by sintering the carbide without binder or by evaporating the binder from sintered compacts in vacuum at 2000°C. Since complete densification of these samples was not desired, they were sintered only to 60 or 80 pct of the theoretical density of tungsten carbide. The specimens were prepared for metallographic examination by polishing with diamond powders and etching with a 10 pct solution of alkaline potassium ferricyanide. Cobalt etches light yellow and the carbide gray. The amount of porosity is exaggerated since it is difficult to avoid tearing out carbide particles, especially from incompletely sintered samples. Experimental Observations A number of specific experiments were carried out in order to study some particular aspect of the sintering problem. The details of these experiments, together with their results, are as follows: Electrolytic Leaching: The binder was removed by electrolytic leaching from sintered tungsten carbide-cobalt compacts for the purpose of determining the continuity of the carbide phase. The method used was based on the work of Cohen and coworkers4 on the electrolytic extraction of carbides from annealed steels. If the sample is made the anode, using a 10 pct hydrochloric acid solution as the electrolyte, the binder is dissolved, but the rate of solution of tungsten carbide is negligible. A current density of 0.2 amp per sq in. was applied. As shown in Fig.

Jan 1, 1953

By Allan E. Martin, Harold M. Feder, Irving Johnson

The cadmium-uranium system was studied by thermal, metallographic, X-7-ay and sampling techniques; special emphasis was placed on the establishment of the liquidus lines, The single inter metallic phase, identified as the compound UCd11 melts peritectically at 473°C to form a-umnium and melt containing 2.5 wt pct uranium. The cadmium-rich eutectic (0.07 wt pct uranium) freezes at 320.6°C. Solid solubilities in uraizium and cadmium appear to be negligible. Between 473°C and 600°C the liquidus line is retograde. NO publication relating to the cadmium-uranium phase diagram was found in the literature. The establishment of this diagram was of considerable interest to us because of a possible application of the system to the pyrometallurgical reprocessing of nuclear fuels. Analysis of liquid samples, metallographic examination, thermal analysis, and X-ray diffraction analysis were used to establish the phase diagram from about 300° to 670°C. Particular emphasis was placed on the establishment of the liquidus lines. The same system was concurrently studied in this laboratory by the galvanic cell method.' Both studies benefited from a continual interchange of information. MATERIALS AND EXPERIMENTAL PROCEDURES Stick cadmium (99.95 pct Cd, American Smelting and Refining Co.) contained 140 ppm lead as the major impurity. Reactor grade uranium (99.9 pct U, National Lead Co.) was most often used in the form of 20-meshspheres. This form was particularly suitable because it does not oxidize as readily as finer powder. The liquidus lines were determined by chemical analysis of filtered samples of the saturated melts. The liquid sampling technique is described elsewhere2 alumina crucibles (Morganite Triangle RR), tantalum stirring rods, tantalum thermocouple protecthecadmiumtion tubes, Vycor or Pyrex sampling tubes, and grades 60 or 80 porous graphite filters were used. Uranium dissolves in liquid cadmium rather slowly. In order to achieve saturation of the melts it was necessary to modify the procedure of Ref. 2 by the use of more vigorous stirring and longer holding periods (at least 3 hr) at each sampling temperature. The samples were analyzed for uranium by spectro-photometry (dibenzoyl methane method) or by polar- ography. The analyses are estimated to be accurate to 2 pct. Thermal analysis was performed on alloys contained in Morganite alumina crucibles in helium atmospheres. Standard techniques were employed; heating and cooling rates were about 1°C per min. For the determination of the peritectic temperature, Cd-10 pct U charges were first held for at least 50 hr at temperatures in the range 435° to 460°C to form substantial amounts of the intermediate phase. For the determination of the effect of cadmium on the a-p transformation temperature of uranium, charges of Cd-25 pct U (-140+100 mesh uranium spheres) were first held near the transformation temperature, with stirring, to promote solution of cadmium in the solid uranium. The holding times and temperatures for these treatments were 18 hr at 680°C for the cooling run and 28 hr at 630°C for the heating run. Alloy specimens for X-ray diffraction and metallographic examination of the intermediate phase were prepared in sealed, helium-filled Vycor or Pyrex tubes. Ingots from solubility runs and thermal analysis experiments also were examined metallographically. Crystals of the intermediate phase were recovered from certain cadmium-rich alloys by selective dissolution of the matrix in 20 pct ammonium nitrate solution at room temperature. Temperatures were measured with calibrated Pt/Pt-10 pct Rh thermocouples to an estimated accuracy of 0.3°C. However, the depression of the freezing point of cadmium at the eutectic is estimated to be accurate to 0.05°C because a special calibration of the thermocouple was made in place in the equipment with pure cadmium just prior to the measurement. EXPERIMENTAL RESULTS The results of this study were used to construct the cadmium-uranium phase diagram shown in Fig. 1. This diagram is relatively simple; it is characterized by a single intermediate phase, 6 (UCd11), which decomposes peritectically, and which forms a eutectic system with cadmium. The solid solubilities in the terminal phases appear to be negligible. An unusual feature of the diagram is the retrograde slope of the liquidus line above the peritectic temperature. The Liquidus Lines. The liquidus lines above and below the peritectic temperature are based on three separate solubility experiments. The data are shown in Fig. 1 and are given in Table I. It is apparent from the figure that the solubility data obtained by the approach to saturation from higher temperatures fall on substantially the same lines as those obtained

Jan 1, 1962

By G. K. Manning, A. R. Elsea, C. R. Simcoe

Boron increases the hardenability of hypoeutectoid steels by decreasing the nucleation rate of ferrite and bainite. It is postulated that concentrations of lattice imperfections, such as exist at the grain boundaries, furnish the necessary energy for nucleus formation. Boron, because of its atomic diameter, will concentrate at lattice imperfections where sites of suitable size are present. Boron will decrease the energy of these local areas by occupying these sites. This mechanism accounts for the large increase in hardenability observed with small amounts of boron. The loss of the boron hardenability effect and the boron precipitate formation are explained on the basis of increased concentration of boron at the grain boundaries either with increasing boron content of the material or with increasing temperature. COMMON alloying elements affect both the nucleation and growth rates of the austenite decomposition reactions.' This effect is largely a result of the slow diffusion rates of these elements. Although a small addition of boron markedly increases the hardenability of steel, the diffusion rate of boron, which is of the same order of magnitude as that of carbon, can hardly account for this effect. An addition of boron in the range of 0.001 to 0.003 pct is about as effective as an addition of 0.30 pct Mo, 0.40 pct Cr, or 1.25 pct Ni in increasing the hardenability of a 0.40 pct C steel;' however, increasing the carbon content of the steel decreases the effectiveness of the boron addition."' The difficulty in understanding why so small an addition of boron can replace much larger quantities of the more strategic alloys, together with the erratic behavior sometimes encountered in boron-treated steels, has interfered with their general acceptance by industry. In the belief that an understanding of the mechanism by which boron increases the hardenability of steel should lead to a more general acceptance of boron-treated steels, a research investigation to determine this mechanism was undertaken at Battelle Memorial Institute under sponsorship of Wright Air Development Center. Experimental Work In order to study the effect of boron on the transformation of austenite to ferrite and bainite, a group of steels was made with a basic composition similar to that of the SAE 8600 series. This base composition was chosen because it has sufficient hardenability to permit accurate measurement of the times required for transformation to start at various temperatures. The chemical analyses of the steels used in the first part of this investigation are listed in Table I. These steels were made as 200 lb heats in an induction furnace. The furnace charge was Armco ingot iron with the alloying elements added as ferroalloys. After the alloy additions were made, the heat was deoxidized with 0.125 pct Al. A 100 lb ingot was cast and an addition of 0.003 pct B, as ferroboron, was made to the metal remaining in the furnace. This metal was cast into a second 100 lb ingot. The ingots were forged to 11/4 in. diam bar stock from which end-quench hardenability specimens were obtained. Part of this material was further reduced by hot rolling to lx¼ in. bar stock from which specimens were obtained for isothermal transformation studies. Studies of Nucleation and Growth: End-quench hardenability tests were performed on these steels, using an austenitizing temperature of 1600°F. The hardenability curves, shown in Fig. 1, indicate that boron treatment resulted in considerable increase in hardenability of the steels. Any such change in hardenability must result from a change in the transformation rate of the austenite, and these rate changes can be established readily by isothermal transformation studies. Isothermal transformation studies were conducted on these steels as follows: specimens were austeni-tized at 1600°F for 15 min, transferred to a lead bath operating at a constant subcritical or intercritical temperature, held for various lengths of time, and water quenched. The specimens were sectioned for metallographic examination to determine the amount and the type of transformation products present. In order to determine the effect of boron on the formation rate of ferrite, isothermal transformation tests were made on the 0.20 pct C steel in both the boron-treated and boron-free condition at an intercritical temperature of 1375°F where ferrite is the only decomposition product of this low carbon austenite. The results of these tests are shown in Fig. 2, where the percentage of ferrite formed is plotted as a function of time at temperature. It is apparent that boron markedly decreased the transformation rate of austenite to ferrite at this temperature.

Jan 1, 1956

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.' The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968