Search Documents

By Robert C. Stephenson

Large deposits of titaniferous magnetite occur associated with anorthosite and gabbro in the Lake Sanford area, Essex County, New York. The ore, gabbro, and anortbosite show consanguineous relations. Anorthosite grades through gabbroic anortbosite into gabbro but is locally intruded by gabbro. Structural and petrographic evidence suggests that gabbro was differentiated from anorthosite by filter pressing. Field and laboratory study of ore occurrences indicates that an ore residuum concentrated in the gabbro through magmatic segregation' by normal crystallization and flowage. Ore occurs as bands which grade into gabbro, and also as large masses which replace anorthosite. Ore in the gabbro is finer grained and richer in ilmenite than ore in anorthosite. Introduction The Lake Sanford area lies in the heart of the Adirondack Mountains, in the southeast portion of the Santanoni Quadrangle (Fig. I), and there are four ore bodies in the area immediately surrounding Lake Sanford. The area lies 30 miles by highway from the railroad at North Creek. The deposits were discovered in 1826, and from then until 1858 iron was produced in small quantities. They were idle from 1858 to 1906. Between 1906 and 1913, extensive development work was carried on. These early attempts to produce iron ore were thwarted by transportation difficulties and by the titanium content of the ore, which, ironically, has been the element responsible for the present development. In 1941 the National Lead Co., Titanium Division, developed the Sanford Hill ore body and is now producing ilmenite and magnetite concentrates.18 The Defense Plant Corporation is extending the railroad to the property from North Creek and is building a sintering plant to treat the magnetite concentrate. Investigations OF the Deposits* Early studies of the Lake Sanford titaniferous magnetite deposits were made by Emmons in 1842,l2 by Kemp, in 1897-98'0 and by Newland in 1908.22 Singewald26 and Osborne23 considered these deposits along with numerous other titaniferous magnetite deposits in 1913 and 1928, respectively. None of these reports entailed a detailed study of the ore occurrence in this area. The present study was begun in 1940. Seven months were spent in the field, and considerable time was spent in labora-

Jan 1, 1949

By George M. Fowler, Joseph P. Lyden

PaGE Scope of this Report.................................................... 206 Production of Tri-State District.......................................... 207 Historical Sketch....................................................... 207 Location and Topography............................................... 211 Geology............................................................... 212 The Tri-State District.............................................. 214 Stratigraphy........................................................... 217 General Geological Section in Tri-State Region....................... 217 Stratigraphic Section of Mineralized part of Boone Formation........... 218 Stratigraphic Section Bird Dog Well.................................. 219 Metamorphism........................................................ 220 Structure............................................................. 225 Regional.......................................................... 225 Due to Metamorphism.............................................. 229 Ore Deposits.......................................................... 231 Types............................................................ 232 Hard-ground Deposits.......................................... 232 Brecciated................................................. 232 Stratified............................................ 232 Sheet Ground............................................. 232 In Dolomite............................................... 233 In Shale.................................................. 233 Soft-ground Deposits.......................................... 233 In the District as a Whole....................................... 233 Ore Minerah and Analysis......................................... 233 Paragenesis....................................................... 234 Conclusions........................................................... 236 Structure.......................................................... 236 Genesis of the Ore.................................................. 237 Future of the District............................................... 239 Acknowledgments..................................................... 239 Discussion............................................................ 239 Scope of This Report The Tri-State district. as outlined in this paper. refers to the entire mineralized area in sout'hwestern Missouri. southeastern Kansas and

Jan 1, 1932

By H. E. Rorschach

Oil-field activities in Oklahoma made 1936 the best year since 1930. Approximately 2800 wells were completed, an increase of about 20 per cent over 1935. Purchasers' reports filed with the Corporation Commission showed a total of 200,240,252 bbl. of oil purchased from leases in 1936. The assembly of a complete table of the oil fields of the state was not achieved, as many of the early records of operators and pipe-line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. The outstanding developments of the year were: the discovery of rich Wilcox-sand production in the Moore pool; the spectacular drilling campaign in the Capitol or Mansion extension in the Oklahoma City pool; the surprising extension of the Olympic pool and the Hunton lime zone in the Fitts pool; and the failure to find more Ordovician production in southern Oklahoma. Wildcat discoveries, which were on a par with 1935, resulted in the discovery of such promising pools as Billings-Wilcox, North Bethel, North Earlsboro and North Lucien. The Fitts-Upper Simpson, Edmond, Jesse, Keokuk Falls and South Burbank pools underwent considerable development. Fitts Pool.—The Fitts area in Pontotoc County was greatly extended during the year and was the leader in drilling activity in the state. The producing limits were pushed to the east and north and the development of the Hunton lime horizon was outstanding. In the Upper Simpson zone 162 wells were completed; 137 in the Hunton lime zone and 26 in the Wilcox zone. The Oil Creek zone, a sand body below the Wilcox member, was discovered by the Magnolia-Statler No. 3 well located in the 1/4. 1/4 of sec. 28-2N.-7E. Moore Pool.—The Moore pool, in Cleveland County, which was opened in 1935 by the Sinclair Prairie-Franklin Community No. 1 well, surprised the oil industry when the Sinclair Prairie-Marvel No. 1 well, on Apr. 1, 1936, discovered a rich body of Wilcox sand below the distillate

Jan 1, 1937

By C. H. P. Lupis, Henri Gaye

There are m -I conditions for the stability of a solution of m components with respect to infinitesinzal flucturations. However, in most cases, only one of these conditions has to be considered to determine the domain of instability and the existence of this more restrictive condition greatly simplifies the calculations. It may be used advantageously for the prediction of miscibility gaps and the method is illustrated in details for the case of the Ag-Pb-Zn system. THE thermodynamic conditions for the formation of a miscibility gap may be viewed as a necessary consequence of the conditions for spinodal decomposition. A previous article1 has examined in detail the form of these conditions for multicomponent systems. There is only one condition for the stability of a binary system (with respect to infinitesimal fluctuations), but there are two conditions for a ternary system, and m — 1 conditions for an m-component system. The probability of violating a stability condition, and thus forming a miscibility gap, obviously increases with the number of components, a result which is rather intuitive since the atoms of the solution have now many more ways of redistributing themselves and introducing complexities in the form of the free energy hy-persurface. It is of interest to take advantage of this possibility of precipitating new phases and to examine which stability condition is the likeliest to be violated, that is, which stability condition is thermodynamically the most restrictive. The finding of such a condition would greatly simplify the application of the stability criteria since only one condition could then be considered, instead of m - 1. In Ref. 1, coherency strain energy terms were neglected, thus restricting the applications of the treatment to solutions where they are negligible, such as liquid alloys. In the following study the same assumption will be made. To generalize the treatment to systems where the strain energy terms are sizable, the reader is referred to Cahn's classical article on spinodal decomposition.2 Let us designate by Gij the second derivative of the Gibbs free energy with respect to the number of moles ni and n j. There are several equivalent sets of m — 1 stability conditions.' The one considered here expresses that the successive diagonal determinants of order 1, 2, ... m — 1, associated with the symmetric Gij matrix (for 2 5 i, j 5 m) are positive.' For a binary solution 1-2, the condition for stability is: O(u=G22^0 [1] For a ternary system 1-2-3, the condition [I.] is re- tained (the value of G22 will differ, of course, according to the concentration of 3) and another condition is introduced: £>(21 = G22G33 - Gl3 ^ 0 [2] In a composition diagram, these two conditions define two domains of instability. Starting at a point where the solution is stable (for instance at a point where the solution is very dilute) we gradually change the composition until the condition [I] or [2] is violated. As already noted in the literature, e.g., in the work of Prigogine and Defay,3 it is the boundary of the domain (2) which is first crossed. For if we assume that the boundary of the domain (1) is reached first, at this point G22 = 0 and the second condition is necessarily violated (D(2) = -& 5 0), in contradiction with our original assumption. An exhaustive study of the ternary regular solution case may be found in the work of Meijering.4 Moreover if the boundaries of the two domains have a common point, they also have a common tangent. For if the two lines were to cross each other as is illustrated in Fig. 1(a) any point M in the line QP would be such that £> = 0 and 0"' > 0 which, as shown above, are incompatible results. Thus, the two lines must be tangent at their common point Q as illustrated in the example of Fig. l(b). The reasoning of Fig. l(a) implies that the point Q is not a "singular" point for either boundary line. This singularity may be of two types. First, the lines meet without crossing each other and without being tangent. Second, the tangent at Q for D"' or 0"' is not single-valued. Other types of singularity are unlikely because of the usual analytical forms of D"' and 0"'. The exception to the common tangent requirement due to the first type of singularity was pointed out by John Morral;5 it occurs when the common point, Q' or (3" in Fig. l(b), is located at a boundary of the composition diagram, e.g., at the line X3 = 0. It may also be noted that at the common nonsingular point Q of D(1) and D(2), Fig. 1(b), G23 is necessarily equal to zero, whereas at a point such as Q' or Q", this conclusion is no longer valid because the product G22G33 is now indefinite (of the form 0. a). The exception to the common tangent requirement due to the second type of singularity occurs when two branches of the same boundary line intersect, for example when D(1)or D(2) decomposes into a product of functions, at a point which belongs to the boundary of the other condition. It is possible to show by a simple analytical calculation that, in this case, if Q is a singular point of D(1), then it is necessarily a singular point of D(2), and that the reciprocal is true except if G33 = 0 at Q. For the present article, however, more elaboration on these singularities appears to be unwarranted. To generalize the previous results to an m -component system, we use the mathematical theorem stating that if the diagonal determinant D(r) = 0, then

Jan 1, 1970

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931

By Joseph E. Pogue

The writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 1, 1917

By E. Maltby Shipp

YouR committee's secretary submits the following report, or summary, to the members of the committee, in an endeavor to lay before them a general review of the information so far received and also his own knowledge of the work as carried on at a number of plants, this being done in part to secure further information and suggestions from members and lead to a more effective means of furthering the work of the committee. It is suggested that more detailed data be compiled regarding engineering features involved, and that papers be contributed which will deal with the safeguarding of underground electrical installations. There are few operating companies which have not started a more or less systematic campaign to safeguard their employees from accidental injuries and unhealthful surroundings, but a great deal is to be gained by experience. All may welcome the advice and cooperation of those who have been actively engaged in the work and have demonstrated the results obtainable by organized effort, and it is, therefore, exceedingly gratifying to note the ready assistance and hearty cooperation rendered by the companies that may be truly termed pioneers in the movement. No solution of the safety problem is to be found in a skrict standardization of methods, rules or devices, as the various mining, milling and metallurgical practices present too many conditions differing broadly in general principles, but some standard system embodying principles already proven to be efficient should be created, which may be modified or elaborated to meet specific requirements of each individual company, or to fit working conditions as they exist in the various mining camps throughout the country. An industrial plant is primarily a business undertaking, therefore the economic side of a safety or welfare campaign is of importance. Many small operators have been deterred from undertaking the work by their belief that it involved an expense beyond their means, and one that could not be counterbalanced by greater efficiency or saving along other lines. This idea is generally due to a lack of knowledge of the actual costs of such work, and of the results secured by judicious selection of a method commensurate with the size and nature of the opera-

Jan 1, 1918

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By Paul Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennesse's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Con-gressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By AIME AIME

MESSRS. BURT and Shockley and others have been for three years urging upon the Institute the matter of simplified spelling. The Institute endeavors to be progressive in the matter of spelling and. is in cooperation with the national body which has this in hand and which has its principal office in New York. Our spellings are changed as fast as-good usage will permit (so it seems to the Board of Directors) and the national body, which is the real representative of the simplified spelling interests, deems that the Institute is making real progress, although not quite as fast as extremists would wish. In January, 1919, Mr. Shockley sent out letter ballots which created a misconception in the minds of many members, who received the impression that the communications came from the Institute instead of from a small group of members. As a result of this propaganda 163 proposal-ballots were sent in to the Institute divided as follows: Yes ?114 No ?20 Negative letters ?9 Split ballots ?20 Total ?163 The total membership at this time was about 7200. The disgusted members would not vote.

Jan 1, 1920

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.' It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this' paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By William M. Baldwin

Jan 1, 1946

By William M. Baldwin

Jan 1, 1946

By Donald A. Brobst

The minerals barite (BaSO4-barium sulfate) and witherite (BaCO3-barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1980 consumed at least 90% of the world's production of 8.8 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite is much less common and abundant than barite, although it is more desirable in many ways as a raw material for the production of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir conditions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemically, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite homogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber industry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and linoleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other substances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weigh down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1983

By J. W. Pugh, J. D. Nisbet

THIS study of the ternary has been made as one phase of a metallurgical investigation which began nearly four years ago in the General Electric Company's Research Laboratory in Schenectady, N. Y. The objective of this program is the discovery of new metallurgical information which will lead to the development of better high-temperature materials. Combinations of the four pure base elements—iron, chromium, nickel, and cobalt—are being studied at the present time. It is essential in an investigation such as this to know as much as possible about the constitutional diagrams involved. The study of the iron-chromium-nickel system has been made to this end. Preliminary Explanation of Experimental Procedure: In all, fifty-five alloys at steps of 10 at. pct were made for the investigation of this ternary. Several ternary alloys in the chromium rich corner had to be omitted because their extreme brittleness made testing impractical. All alloys were vacuum melted with hydrogen reduction and centrifugally cast. The apparatus and technique of this process has been described in detail by Nisbet.1,2 The purity of the alloys prepared in this way is considered to be quite good. Impurities are listed as follows: Pct Carbon.............................0.02 Oxygen................................0.02 Nitrogen.........................0.005 Magnesium..................0.03-0.05 Sulphur...........................trace Hydrogen....................trace Phosphorous..................trace Silicon........................ trace After casting, all samples were given a homo-genization treatment which consisted of holding them for 15 hr at 1150°C (2100°F) and water quenching. Testing was begun with the samples in this condition. The tests employed in the study of this system were (1) dilatometer, (2) hardness versus aging temperature, (3) tensile strength and elongation versus temperature, (4) microstructure analysis, and (5) electrical resistance versus temperature. Dilatometer tests were made at the rather rapid heating rate of 1093°C (2000°F) in one hour on a Bristol-Rockwell type instrument. Hardness data were taken on specimens cooled from 204", 427", 649°, 760°, 871°, 982°, and 1093°C under conditions which are thought sufficient to bring the specimens to equilibrium in all but the cases of the very sluggish transformations. Electrical resistance data for several specimens were taken for both heating and cooling conditions in a vacuum furnace especially designed for this work by D. W. Bainbridge, formerly of this laboratory. Provisions were made for heating and cooling standard specimens at a constant rate, while autographic records of resistance and temperature were made simultaneously. Micrographs of all the alloys were made in the quenched condition. Some question may exist as to how such physical values as hardness, tensile strength, and elongation were interpreted to indicate a change in phase. Original data were recorded on physical property versus temperature graphs, each of which was made from the data of a single alloy (fig. la). From these, another series of graphs were plotted with the physical property as a function of composition for constant temperatures (fig. 1b). Sharp deviations in the slope of these composition versus hardness curves often indicate a change in phase. The example of fig. 1 will serve to describe this experimental technique. The plotting of a single point from graph "a" to graph "b," and finally to the phase diagram "c," is illustrated. The location of the point on graph "b" is indicated as point (1). If all the alloys of the A-B binary system were solid solutions at temperature X, the hardness in this curve would be expected to rise at a fairly even rate as A is diluted with B to a maximum at some intermediate value between A and B, as

Jan 1, 1951

By J. J. Bean

Concentrating mixed sulfide-oxide copper ores by the leach-precipitation-flotation method is an old operation at the Miami Copper Co. The idea was conceived and the method developed at Miami by F. W. Maclennan and Harmon Keyes during the years 1929 to 1934, and it was these men who gave the term LPF to this process. Miami at that time had considerable reserves of mixed sulfide-oxide ore.* In the development of a suitable treatment method, it was natural that leaching of the oxides with acid and the precipita¬tion of copper from the resulting copper sulfate solution by iron was investigated. The separation… • The term oxide as used in this article includes the copper oxides, carbonates, and silicates.

Jan 12, 1960

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note. This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material In which the crystals here dealt with were grown was made from 1/8 -in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of travelling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection.

Jan 1, 1927

By Stanford O. Grodd

The Sanford Lake district encompasses an area covering 24 square miles in the central Adirondack Mountains of northern New York State. Discovery of the titaniferous magnetite deposits dates back to 1826. Several attempts to exploit the ores for iron prior to 1942 proved uneconomical because of difficulties with the associated titanium, lack of transportation facilities, and the isolated location. Since 1942, the National Lead Company has produced ilmenite concentrates for the titanium pigment industry, and a magnetite by-product used in the steel and refractory industries. Rocks of the area are Precambrian in age and of igneous origin. The area has a history of erosion, deformation, and metamorphism, subsidence, and finally uplift and glaciation. The resulting topography is extremely rough with drainage patterns controlled by a combination of fault patterns and glacial modifications. The district is within the large anorthosite massif making up the central high peak area of the Adirondacks. All of the various lowsilica rock types associated with the massif are found within the boundaries of the district. These consist of both the Marcy and Whiteface types of anorthosite and of gabbroic anorthosite, gabbro, and different grades of titaniferous magnetite ores. All of the rocks contain the same minerals and differ only in their percentages of these consitituents. Gabbro, and ore associated with it, demonstrate flow structure as both have foliation and lineation. Anorthosite and its associated ores are massive and show very little primary structure. Minor pegmatites and diabase dikes provide evidence of remobilization in selected areas and of late intrusion as well. Faulting is prevalent and follows a regional pattern of major faults trending northeastsouthwest and of minor faults at nearly right angles to them. There are four mineralized areas where an economic grade of ore has been found. Three of these have both gabbroic-type ore and anorthositic-type ore. The fourth has only gabbroic ore. Ores are graded according to their TiO, content, and these range from 9.5 per cent to over 30.0 per cent TiO,. Ore bodies of both types are related to gabbro and conform to the configuration of the gabbro bodies within the anorthosite. At least three distinct theories of ore genesis have been expounded by different investigators. Others propose some variations of one or more of these. Although complete agreement probably never will be reached, it is certain that no one process of ore emplacement can explain the complicated picture as seen today. Further understanding of the ores and their origin will require detailed mapping, sampling, and mineralogical studies of the entire district, and then it may never be understood without qualification.

Jan 1, 1968

By N. L. ALISON

MUCH has been published on the general subject of metal mine ventilation but, so far as I can discover, few specific data on selection of fan equipment to meet the requirements of a given mine ventilation problem are available. This article is intended to point out some of the more important considerations which influence the selection of such equipment. It will be assumed that the mine operator is able to determine the quantity of air which is necessary in the various parts of his mine to produce the required results and the pressure in inches water gage needed to circulate this quantity of air through the mine. There may be instances in which this assumption is not justified, but the fact remains that, with proper engineering talent, these data can be approximated sufficiently close for practical purposes.

Jan 1, 1930

By E. V. Daveler, Frank L. Antisell

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface, and the "set," or the decail appearance of the surface of the shape. The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are these characteristics connected that they are often used as synonymous terms by the refiner when he is speaking of well-refined copper. Oxygen is often spoken of as a medicine for copper, it being used to regulate the pitch.

Jan 1, 1920