Search Documents

By B. D. Smith, K. H. Coats

Experiments in which calcium chloride displaced sodium chloride from four cores showed the extent of asymmetry in the resulting effluent concentration profiles. These results provided a check on how validly the mixing process is modeled by a differential (i.e., not finite-stage) capacitance mathematical model. The effluent concentration profile from two consolidated cores exhibited considerable asymmetry, while two unconsolidated cores yielded nearly symmetrical profiles. All runs resulted in breakthrough of the 50 per cent concentration significantly before one pore volume was injected. In addition, velocity appreciably affected the effluent concentration profile from a Torpedo sandstone core. The differential capacitance model matched the data significantly better than a simple diffusion model. The capacitance model allows determination of the amount of dead-end pore space in a porous matrix and the effect of velocity on the rate of diffusion into this space. An experimental program yielding insight into the physical validity of the capacitance effect is described. INTRODUCTION Axial dispersion — the mixing accompanying the flow of miscible fluids through porous media — has been the subject of many relativeiy recent studiesl-13 and a comprehensive review of the topic has been given by Perkins and Johnston.14 This dispersion is of practical interest in studies of the miscible displacement process, fixed-bed chemical reactors, and the adsorption of solutes from a flowing stream onto the surface of a porous medium. In the latter case, the effect of dispersion must be considered when adsorption parameters are determined from the nature of concentration profiles. In general, early studies of dispersion assumed applicability of a simple diffusion equation and were concerned with correlation of the experimentallv determined "effective" diffusion coefficient with system properties over a large range of the latter. Recent have been concerned with the deviations between the asymmetrical effluent concentration profiles observed and the symmetrical ones predicted by the diffusion model. In the present study, effluent concentration profiles were obtained from consolidated and unconsolidated cores. These profiles were compared with those predicted by a differential (i.e., not finite-stage) capacitance model. Solutions to the simple diffusion model, for three sets of boundary conditions, were compared with one another and with the experimental profiles. SUMMARY OF PREVIOUS WORK The reader is referred to Perkins and johnston14 for an extensive review of studies of dispersion in porous media. Many investigators have employed the simple diffusion model characterized by Eq. 1 below: The dispersion coefficient D for unconsolidated systems is correlated by u is interstitial velocity and dp is particle diameter. Since heterogeneity of the sand pack affects the mixing, this equation is also expressed as where a is proportional to the degree of heterogeneity and is about 3.5 for random packs of unconsolidated sand.l4 Eq. 3 holds for 2 For a Do homogeneous (regular) type of packing, should be 1 or less.6 Aris and Amundson6 and Carberry and Bretton consider o to be the number of particle lengths per mixing cell in the finite-stage model. Data from consolidated cores indicate dp to be about 0.36 cm for outcrop rocks, Torpedo sandstone having a reported value of 0.17 cm.15 For v /Do less than about 2, the effect of molecular diffusion must be considered and the total dispersion coeffi-

Jan 1, 1965

By F. F. Craig

A series of both welter and gas puttern Hoods was made in the laboratory to study the oil recovery performances of .such operations. These tests were contlrrctt~tl on consolidated sandstone models, using oil. water, and gas. The model floods were scaled to reprotlrrce field performance under gas arid water five-spot injection. X-ray shadowgraphs permitted observation of the gross fluid movement within the models. A method was developed for applying the mobility ratio concept to water flooding and dispersed gas drives in a five-spot well pattern. The area1 sweep efficiency. tit breakthrough for dispersed gas drives is much higher than previorsly expected, Iying in the range of 50 to 100 per cent. A method is presented for predictitig the water-oil ratio performance of five-spot pattern water flood., in uniform sands. This method is verified experimentally for the cotidition of 120 free gas initially present and for va1ues of gas saturation normally encountered in fields following depletion operations. Prodrrction perfort?zut~cc for pattern gas injection is also predictable by this method. INTRODUCTION In field pattern hater flooding or dispersed gas injection operations, the displacing fluid (water or gas) is injected and oil is produced through wells which are, area-wise. small openings in a large container or rescrwir of oil. As a result, not all of the area between the injection and producing wells is necessarily contacted by the injected fluid by the time it first reaches the producing wells. The question arises in predicting oil recovery. as to what traction of the pattern area involved is contacted by either the injected water or gas due to the relative position of the injection and producing wells. This is the areal sweep efficiency. It is also desirable to know how well arrangement affects the oil production performance. A solution to this problem has been attempted by many means. Mathematical analysis¹,²,³, and electrolytic models', have been used to establish a breakthrough areal sweep efficiency of 73 per cent for a five-spot pattern in which the ability of the oil to flow ahead of the invading fluid is equal to the ability of the invading fluid to flow in the invaded zone. All of these studies simulate only one of many field conditions. Improved studies of areal sweep efficiency at breakthrough were made using the fluid mapper5, poten-tiometric models" and X-ray shadowgraph techniques. In these it was possible to study the effect of variations in mobility of the injected and displaced fluids, and so to cover a wide range of field conditions. The limitation of these studies is that, with these models, it was not possible to simulate the saturation gradient behind the flood front when oil is displaced by gas or water. In the most recent published technical paperS on the subject, a method was presented for predicting the oil recovery performance after breakthrough in a five-spot pattern water flood. The method involved correlations which were obtained experimentally using miscible fluids. One limitation of this work was that a saturation gradient, usually found in immiscible fluid displacement, was absent in these studies. Also the laboratory studies did not cover the situation of a water flood following oil recovery by depletion drive. as is the situation in most field water floods. The tests reported in this paper were made using oil. water, and gas, thus eliminating the simplifications of former studies. Also reported are laboratory studies on

Jan 1, 1956

By Robert B. Hall, Charles W. Bauer

Alunite, KA13(SO4)2(OH)6, was used from the 15th century until early in the present century as a source of potash alum and aluminum sulfate. Since early in this century its use for this purpose has declined to virtually nil with acid treatment of bauxite or clay replacing alunite as a source of alum. During the First World War alunite served as an emergency source of potassium sulfate fertilizer in the United States and Australia. More recently, alunite has been investigated as a nonbauxite ore of aluminum, with potassium sulfate and sulfuric acid as recoverable byproducts. The Soviet Union established a commercial-scale plant in the mid-1960s producing cell-grade alumina from alunitic ore and recovering byproduct potassium sulfate and sulfuric acid. Interest in nonbauxite ores, including alunite, is expected to continue in countries that presently are dependent on imports of bauxite or alumina to support their aluminum industries. The US has the largest aluminum producing and fabricating industry in the world but imports more than 90% of its aluminum-bearing raw materials. This chapter reviews the status of alunite as a potential source of aluminum with byproduct fertilizer, and the resources available to support this industry, whenever this becomes economically feasible. Historical Background Alunite has received little attention until recently, yet for centuries it held a higher place than many of the industrial minerals considered essential today. The deposits of alunite at Tolfa, northwest of Rome, were mined almost continuously from 1462 until about the middle of the present century (DeLaunay, 1907; Lombardi, 1977). The potash alum made from the alunite, called Roman alum, was a valued commodity in international trade, being used in the making of paper, in tanning leather, and as a mordant in textile dyeing. The industry at Tolfa is said to have been controlled by the Vatican and was a source of revenue for the Papal State until fairly recent times (Lombardi et al., 1977). Since early in the present century, the preferred method for making alum has been by acid treatment of bauxite, clay, or other aluminous material, so that alunite has fallen into near-total disuse as a source of alum chemicals. Appreciable quantities of mixed alunite-kaolin rock still are quarried in the Tolfa district for use by the Italian cement industry (Lombardi and Mattias, 1979), but the role of this material in the making of Italian cement is not clear. A large deposit of alunite-bearing rock in Chekiang province, mainland China, is said to have yielded a "great quantity" of alum over a period of several centuries (Yih, 1931). During the 19th century, alunite deposits in France, Spain, Australia, and other countries were exploited as raw material for making potash alum and aluminum sulfate. Interest in alunite was revived during the First World War, not for alum, but as an emergency source of potassium sulfate fertilizer. Large veins of nearly pure alunite had just been discovered on Alunite Ridge, 11 km southwest of Marysvale in Piute County, Utah (Butler and Gale, 1912), and these were quickly brought into production for making potash fertilizer to replace supplies cut off from the famous deposits at Stassfurt, Germany. An estimated 225 kt of Marysvale alunite was mined and processed at that time (Callaghan, 1973). Similarly, Australian alunite deposits were mined as a source of potash fertilizer during both world wars (Hall, 1978).

Jan 1, 1983

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of&apos; this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By P. Chiotti, E. R. Stevens

The electromotive force between pure magnesium and Mg-Zn alloys in a fused KC1-LiCl-MgC12 cell was measured over the temperature range 360° to 730°C and for alloy compositions of 0.052 to 0.635 atom fraction magnesium. The calculated activity coefficients of magnesium in the liquid alloys may he represented by the relation These data and the phase diagram were employed in calculating the standard free energy of formation for the compounds MgZn, MgZn2, and MgZn2, In the temperature range from 25° to 590°C the relation ZINC-rich magnesium alloys have been shown to be very effective in reducing various solute chlorides or oxides from fused salts such as KC1-LiC1 eutectic. Such reactions are of interest in the developinent of pyrometallurgical methods for reprocessing nuclear reactor fuels.&apos; As the conceniration of the magnesium is increased beyond 5 to 10 wt pct the extent to which solutes, such as yttrium, lanthanum, cerium, and other rare earths, can be reduced or removed from the salt decreases. This effect is due to the resulting change in the activity of the solutes in the Zn-Mg alloy as well as the change in the activity of both the zinc and mag- nesium. The purpose of the present investigation was to determine the thermodynamic properties of the Zn-Mg system which, in addition to yielding information on the alloying behavior of these two elements, would permit a more quantitative understanding of the above reactions. Since this investigation was initiated several publications have appeared in the literature giving results on the thermodynamic properties for the liquid alloys of this system. 2-4 Kozuka, Moriyama, and Kushima3 measured the vapor pressure of zinc over four different alloy compositions by a carrier-gas technique. Eremenko and Tukashenko2 and Terpilowski4 measured the electromotive force between pure magnesium and various alloys in a fused salt cell. Earlier work has been summarized by Hultgren, Orr, Anderson, and Kelley.5 In the present investigation electromotive-force measurements were made on a cell of the type The temperature range covered for the lower-melting alloys was roughly 375° to 730°C. These data were employed in calculating the thermodynamic properties for the liquid alloys and in conjunction with the phase diagram,&apos; reproduced in Fig. 1, were used in calculating the standard free energy of formation of the compounds MgZn, MgZn2, and Mg2 Zn11. The results obtained are compared with available data from the literature. MATERIALS AND EXPERIMENTAL PROCEDURES Materials employed were: Bunker Hill slab zinc, 99.99 pct pure; Ames Laboratory magnesium containing 13 ppm N, 195 ppm C, and trace amounts of calcium, copper, nickel, and silicon; reagent grade KC1, LiC1; and high-purity MgC12 obtained from Dow Chemical Co. The electrolyte consisting of KC1-LiCl eutectic (44.4 wt pct LiC1) to which was added 15 wt pct MgCl2, was dried in a quartz tube by heating to 340° C under vacuum for a period of 4 to 5 hr, and then passing HC1 through the salt as the temperature was slowly raised to above the melting point of the salt. After about 3 hr the HC1 was shut off and the system flushed with argon and then vacuum applied for 1 hr. The salt was finally siphoned through a sintered glass filter and cast into a Pyrex container which was sealed and

Jan 1, 1965

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,&apos; Zr-Si,&apos; and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies&apos; and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.&apos; Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,&apos; was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By H. H. Rachford

This work presents a first-order analysis of the instability underlying viscous fingering in adverse viscosity-ratio water floods. It extends previous analyses of frontal instabilities, which were carried out with equations for parallel plate models, by including effects of the saturation transition zone observed behind the front in water floods in water wet systems. This zone tends to insulate incipient fingers from the high-mobility watet;. thus conditions for the onset of fingering differ from those in the parallel plate theory. Finite-difference solutions of the two-dimensional equations of displacement in porous media exhibited the predicted stability characteristics in six hypothetical field- and laboratory-scale floods in rectangular reservoirs. In contrast to results with parallel plate systems, this paper concludes that for waterwet reservoirs, laboratory models scaled by the usual criteria are also correctly scaled for frontal instability. Further, fingering in the systems studied can occur in any saturation range behind the front, and may occur at an intermediate saturation even though stability obtains both at the saturation corresponding to the Buckley-Leverett front and near residual oil saturation. Other points of contrast are that the likelihood of occurrence of fingering may not increase as flow rate or viscosity difference increases, but my be sensitive to changes in he relative permealdlity and capillary pressure functions. INTRODUCTION The recovery of oil by water flooding frequently involves displacing the oil by water of a lower viscosity. Displacement of a fluid by a less viscous one may lead to gross channeling or fingering like that observed in solvent floods, in which it severely lowers recovery efficiency.1 In addition to adverse effects on recovery, it has been suggested that the unstable move- ment causing fingering may interfere with interpretation of scaled model studies of proposed water floods, since the instability in the model might not be faithfully scaled to that in the reservoir prototype. In view of the serious implications of this possible breakdown of widely used scaled model techniques4-6 it is the purpose of this paper to examine the question further. Instabilities in the solutions of systems of differential equations imply a loss of smooth dependence on initial and boundary conditions. Thus, the possibility exists that in using models whose scaling is based on the differential system there may arise size- and rate-dependent factors which are not properly scaled. This possibility was examined in detail by Chouke et al., who analyzed the instability of frontal advance in a related problem, water-oil displacement in parallel plate models,2 in which a moving interface separates two regions of constant, unequal mobilities. First-order perturbation theory predicts the existence of a critical wave length for the growth of perturbations: and a wave length of maximum instability of A, = The interpretation is that wave lengths in a perturbation which are longer than A, will grow. Thus, if the width of a two-dimensional channel is greater than A,, fingers will grow, and the spacing of the fingers which grow at the maximum rate will be approximately It is important that the higher the velocity and/or the difference in flow resistance, the lower is A,, and thus the greater the number of fingers that can grow in a given model. In applying these conclusions to porous media, a pseudo-interfacial tension, , was assumed for the invasion front. Since this would not necessarily be equal to the liquid-liquid interfacial tension, an unknown constant was substituted for the foregoing expression for A, This was determined

Jan 1, 1965

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan&apos; obtained kinetic data for the reduction of hematite spheres sintered at 13&apos;70°C (2498&apos;F&apos;). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph&apos; and Edstrom&apos; that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By H. H. Rachford, D. W. Peaceman

A system of partial differential equations describing miscible displacement of fluids in porous media is derived The system takes into account the influence of gravity, the spatial distribution of permeability, diffusion, and fluid viscosities and densities. A numerical procedure for approximating solutions to the differential systems has been tested for a horizontal two-dimensional geometry. In end-to-end displacements of oil with less-viscous solvents, the numerical solutions exhibited fingering qualitatively similar to that observed in laboratory models. Small random spatial variations in permeability about the mean value are sufficient to initiate fingering. Quantitative comparisons of computed results with laboratory data show good agreement. INTRODUCTION Miscible flooding of oil by solvent is receiving increasing consideration for field use.1-4 Unfortunately, such floods potentially present severe problems in loss of recovery through the by-passing of oil by expensive solvent. Consequently, their economic evaluation requires sound techniques for predicting recovery. The purposes of this work are to present a finite-difference method for calculating the multidimensional displacement of oil by solvent and to investigate the validity of the method by comparing results of calculations with data from displacements in laboratory models.5 The formulation of the method to simulate the model experiments treats a case of limited scope in the description of solvent flooding in the reservoir. The model experiments were carried out with fluids that were assumed to form an incompressible, ideal, two-component system with constant diffusivity. Establishing the validity of the method even in its present form provides a major step toward the goal of quantitatively evaluating individual solvent flooding projects. First, it demonstrates the fea- sibility of calculating the course of displacements which are dominated by an inherent macroscopic instability, i.e., viscous fingering. In addition, the method provides almost the only practical means of examining the effect of the size and extent of reservoir inhomogeneities on the development and propagation of the fingers, taking into account the important influences of diffusion and gravitational segregation. It might be inferred that such studies cannot yield results of practical value because in displacements dominated by macroscopic instability the pattern of finger development and the resulting performance should depend critically on small variations in the geometric distribution of reservoir inhomogeneities. The present method offers the capability inherent in computational techniques of predicting performance reproducibly with any arbitrary distribution of reservoir properties and, as such, provides a means of evaluating the sensitivity of behavior to uncertainties in reservoir definition and, thus, assessing the reliability of prediction of performance. THE PHYSICAL PROBLEM DATA USED FOR QUANTITATIVE TESTS OF CALCULATIONS In this work, a calculation for treating the miscible-displacement process is tested by comparing calculated results with experimental data. The experiments chosen for comparison have been described in detail,5 and the quantitative features are summarized in a later section. Briefly, oil was flooded by solvent of equal density from a thin rectangular channel in Lucite packed with uniform Ottawa sand. Under these conditions, two-dimensional geometry is considered adequate to represent the process. Inasmuch as the present work is concerned with testing of the method by comparison with specific two-dimensional data, the system of equations presented in the succeeding section will be oriented to defining the physical system specifically. THE DIFFERENTIAL EQUATIONS Suppose x, y to be a Cartesian co-ordinate system and define h(x, y) to be the height of a point above a horizontal reference plane. It will be assumed

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers&apos; as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953

By B. H. Caudle, A. R. Khan

The oil production performance of thin-oil-column type reservoirs producing entirely by natural water drive are discussed in this paper. The dimensionless production histories were obtained in a series of scaled porous-medium laboratory-model tests under varying effects of rate of production, mobility ratio across moving boundary, ratio of oil- and water-sand thickness and mobility ratio across fixed boundary including the effects of different residual oil saturations in the water-invaded regions. This scaled-model study of thin oil columns indicated that greater recovery of oil results for lower values of the following: rate of production, mobility ratio across the moving boundary, water-sand thickness relative to the oil-sand thickness, and mobility ratio across the fixed boundary or residual oil saturation in the water-invaded region of oil sand The results of the study are given as dimensionless production history plots which may be used to predict the performance of the field they represent. INTRODUCTION Oil fields producing under natural water drive can be classified into two major groups: (1) an "edge-water drive" reservoir group in which the water is encroaching from the reservoir periphery, and (2) the group of reservoirs in which the oil-sand is entirely underlain by an aquifer. Reservoirs in the second group are further subclassified as "bottom-water drive" reservoirs and "thin-oil-column" reservoirs. The latter reservoirs are characterized by their relatively equal oil- and water-sand thicknesses and by having both the oil and water zone relatively thin. When oil is produced from a water-drive reservoir by a partially penetrating well, water breaks through sooner or later before all of the displace-able oil is recovered. Many analyses of this general situation have been made with varying degrees of realism in their approaches, both theoretical and experimental5.6 in nature. Pertaining to the scaled laboratory model studies of natural water drives using porous media, detailed investigations have been made by Henley, et al.7 on bottom-water drive and by Caudle8 on edge-water drive reservoirs. No laboratory model studies, however, have been made to investigate the performance characteristics of thin-oil-column reservoirs. This paper presents the results of a study on scaled models of thin-oil-column reservoirs, operated under varying conditions corresponding to the actual field practices. SCALING PARAMETERS The object of scaling is to produce a one-to-one relationship between physical and dynamic parameters of the model -and prototype. The most comprehensive treatment of scaling techniques for oil reservoirs is given by Geertsma, et a1.,9 which covers two methods for arriving at dimensionless groups for scaling. Table 1 lists the scaling parameters suitable for creating kinematic and dynamic similarities between the model and the prototype in the variables considered for the thin-oil-column reservoirs. In order to achieve similarity it is essential that the dimensionless groups listed in Table 1 have equal values in the model and the protorype simulated. Since it has been established that the role of interfacial forces is neglible in gross fluid movement in a reservoir no attempt was made to scale capillary forces- Although there are reports describing Scaling criteria for these forces,10,ll consideration of the necessary but restrictive conditions for

Jan 1, 1970

By M. P. Tixier, M. Gondouin, G. L. Simard

In the quantitative interpretation of the SP logs, the electrochemical component is generally taken equal to — K log Rm /Rw where K has the theoretical value corresponding to solutions of pure sodium chloride. This method may be misleading when relatively large quantities of salts other than NaCl are present in form-rrtion waters—as is generally the case for low salinities —or in gyp-base muds. In such cases recourse is made in the field to changing the K value or to adding a correction term to the equation on the basis of local experience. An investigation has been made in the laboratory of the influence of HCO3, SO4=, Ca++, and Mg++ on the amplitude of the SP deflection, which included in par-ricular determinations of the activity coefficients of Ca++ and Mg++. The theory, the experimental techniques and a tentative method for applying the results are described. So far, applications to actual field cases where chemical analyses of waters were available have provided an excellent confirmation of the proposed method. The case of the SP in very salty brines is also considered and it is shown that the use of activity data for sodium gives satisfactory results. HISTORICAL In early times of electrical logging, the SP curve was used exclusively as a tool for the location of permeable beds and the definition of their boundaries. Later, with the introduction of methods of quantitative analysis, attention was called to the possibility of deriving from the SP log some information on the formation water resistivity, which constitutes one essential element for the computation of water saturation from log data. The first laboratory experiments&apos; in 1932 had shown that, as a result of electrochemical phenomena arising at the contact of the niud and the formation, the amplitude of the deflection of the SP curve was, at least partly, a function of the salt concentration of interstitial water and accordingly of its resistivity. It was indicated that the amplitude of the electrochemical component of the SP should be equal to K log R1/R2, R1 and R2 being the resistivities of the mud and of the formation water respectively. However, the exact value of the K coefficient was not determined at that time because the surface clay used for a laboratory model was far from an ideal shale membrane. Consequently, the way was not yet open towards quantitative interpretation. In the early forties, Tixier reported2, on the basis of field log observations, the following equation for the case of NaCl solutions, SP = -71 log f1c1/f2c2, c1 and c2 being the concentrations and f1, f2 the mean activity coefficients. The local variations observed in the empirical values of K, chiefly in the Rocky Mountains, led him to advance the opinion that, besides the relative amounts, the nature of the salts present in the solutions had a bearing on the magnitude of the SP. At about the same time Mounce and Rust- ad published laboratory results which emphasized the part played by the shale in the generation of the SP. On the basis of laboratory tests and theoretical considerations, Wyllie in 1948&apos; published the following equation of the electrochemical SP for the case of NaCl solutions, SP= - 71 log (a1)m/(a2)m

Jan 1, 1958

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y&apos; alloys by gas quenching, is extensively ordered prior to y&apos; (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y&apos;, Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y&apos;. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y&apos;, or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.&apos; The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.&apos; An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By T. E. Scott, R. P. Zerwekh

The charactevistics of the deformatiotz of fcc thorium were examined between 78 and 473 K. Activation energy, actiuation volume, and the temperature dependence of the flow stress were determined and conlpared uith several theories for the rate-controlling mechnnistn of the tempemture-dependent component of the flou~ stress. It was established that the Cottrell-Stokes law does not hold, even approximately, for thorium. Through consideration of the above factors and other parameters, it was concluded that the vandom solute barrier theory proposed by Friedel demonstrates the best agreement with experimental observations of the deformation of thorium below ambient temperature. THORIUM, the first metal in the actinide series of rare-earth elements, is interesting and important from two points of view. In the more practical vein, it is a potential reactor fuel. As such, it is important to know its properties. Of specific interest here are the mechanical properties of thorium. Second, no detailed information concerning the deformation characteristics of the actinide elements has been gathered to date. In view of the interesting physical and chemical properties of these metals, their mechanical behavior might reveal characteristics which could improve our understanding of the mechanisms controlling deformation of the more common metals. For example, it has been shown1 that thorium exhibits a yield point which is greatly enhanced by interstitial solute elements such as carbon. This is not a normal occurrence in fcc metals. The goal of this investigation, therefore, was to characterize the deformation of polycrystalline thorium. MATERIAL AND PROCEDURES Thorium, made by the magnesium intermediate alloy process described by Peterson et al.,2 was rolled and swaged to 0.065-in.-diam wire. The metal analysis is given in Table I. After preparation, the oxygen and nitrogen contents had risen to 308 and 60 ppm, respectively. The 0.065-in.-diam wires were cut into 2-in. lengths and annealed in a vacuum of lo-&apos; Torr at 750°C for 1 hr, producing a grain size of 2735 grains per sq mm. The ends of the 2-in. sections were masked off so that a 1-in. gage length could be electropolished. Specimens were polished at 35 v in a solution of 6 pct perchloric acid in methanol which was maintained at 0°C . The gage diameters after polishing were about 0.0625 in. The tests were run on a screw-driven tensile machine at a constant crosshead speed corresponding to a strain rate of 0.005 min-&apos;. The strain rate was changed rapidly after each 0.01-in. extension between 0.005 min-&apos; and one of three higher strain rates which were selected in order to achieve strain-rate ratios of 5, 10, and 20. Tests were run at several temperatures from 78" to 473°K; most were tested at 423", 300°, 215", and 78°K. EXPERIMENTAL RESULTS Flow Stress vs Strain and Temperature. Typical true stress-true strain curves for thorium are shown in Fig. 1 for several temperatures over the range 473" to 78°K. The curves for 78", 215", 300") and 423°K were obtained from strain-rate change tests using the lower (0.005 min-&apos;) or base strain-rate values of stress. Additional tests, using the same base strain rate at different strain-rate ratios, gave curves which virtually superposed on those shown, indicating that strain-rate changes did not materially influence the work-hardening characteristics at the base strain rate. The curves for 273") 373") and 473°K were standard tensile tests at 0.005 min-&apos;. The behavior of the flow stress with temperature is

Jan 1, 1968

Draftsman and transitman for coal mine work in Middle West. Salary $125 per month. No. 277. Mechanical draftsman familiar with mill and machinery design for metallurgical and chemical plants. Advise experience, salary expected, and references. No. 289. Two cyanide shift bosses, one cyanide mill supt, and one assayer, for work in South America. Expenses clown and return if two year contract is made. No. 290. In assay laboratory of University in the Middle West, man to take charge of ore-dressing and. help in assay laboratory work. Willing to give right man assistant professorship. No. 291. Experienced appraisers familiar either with field or office methods, capable of field survey of the physical properties and able to check up their survey on the books of the company, which require a very intimate knowledge of accountancy. Salary $2000 to $2700. No. 292. Young man trained in chemistry and engineering to conduct experimental work on storage of coal. No. 293.

Jan 4, 1918

Paralleling recent experiments in the U. S., the Mines Branch of the Department of Mines and Technical Surveys in Ottawa has developed a laboratory process for recovering cell-grade alumina from aluminiferous shale. Mines Branch Research Report R45 (1959) entitled The Alum-Amine Process For The Recovery of Alumina From Shale by G. Thomas and T. R. Ingraham states " . . . With the recent resurgence in Canada, and in the United States, of attempts to recover cell-grade alumina from clays and shales, the Mines Branch undertook to review certain processes that had been tried with marginal success . . . In particular, it seemed quite possible that some recent developments in organic chemistry, relating to uranium technology, might be utilized for the removal of the last traces of iron from intermediate products to permit the attainment of a satisfactory grade of alumina." This introductory paragraph explains the authors&apos; approach toward development of an alumina recovery process from shale. The following is an abstract of their successful laboratory experiments.

Jan 3, 1960

The paper by Professors Sun and Mitchell illustrates the value of ultrasonics as a tool for the mineral engineer. In particular, it opens up a number of possibilities to those interested in the field of comminution. The provision of desliming technique, which is thorough as well as rapid, is a distinct contribution, but the data of the paper suggest applications beyond desliming, in that the same treatments may be useful for size determination purposes. Fig. 1 shows that a marked dependence exists between particle size and the height to which it can be elevated by ultrasonic vibrations. While the curves are only extended down to a size of about 100 p, the fact that they appear to be increasing in slope in this range suggests that the separation may be even more marked here. This, we feel, is very strong evidence that a method for fine sizing could be developed to use ultra- sonic waves as the separating force.

Jan 1, 1957

By Henry M. Howe

I NOW call your attention to two directions in which very important progress may be confidently hoped for—pyrometry and the heat-treatment of steel. We already find in the market more than one pyrometer which, in spite of serious defects, may lie used advantageously for determining and controlling the temperature of many of our metallurgical processes. It is to be hoped, and with much confidence, that by the rapid extension of the use of such instruments, the economy and efficiency of these processes may undergo an increase which, in the aggregate, will be of the greatest importance. In this connection, the lucid paper of Prof. Roberts-Austen," and the learned bulletin of Mr. Barus, are most welcome. But much remains to be done in the way of devising pyrometers suitable for manufacturing purposes. While some of the present pyrometers are most convenient and accurate in the laboratory, serious difficulties attend the use, in factories, of those which I have

Jan 1, 1895