Search Documents

By L. Zwell, H. A. Wriedt

In describing their procedure for measuring the lattice parameters of solid solutions, Abrahamson and Lopata report (p. 77) the final heat treatment of their alloy specimens as "700°C for 100 hr, followed by a furnace cool". The isothermal part of this treatment may be expected to precipitate solute in excess of the stable a solid-solution limit at 700°C; the subsequent slow cooling is likely to reduce the dissolved solute still further. Fig. 1 (upper) presents the data for titanium alloys so he;rt-treated and shows the lattice parameters of solid solutions containing up to 3.5 at. pct Ti; Fig. 17 (lower) shows 2 at. pct Ti as the solubility limit in a iron at 700°C. Figs. 1 and 17 are thus incompatible. The paper contains comparable incon~patibilities for zirconium alloys, for niobium alloys, and for tantalum alloys. The final heat treatment at 700°C may also be responsible for the anomalous "knee" in the lattice-parameter data for nickel alloys, Fig. 3. The "knee" composition is located near the 700°C limit of the stable a solid-solution field;37 alloys of the experimental composition range with more nickel than the "knee" composition are two-phase at 700 C and prolonged heat treatment of them at 700°C would tend to produce inhomogeneity rather than homogeneity. In Figs. 4 and 7, the composition ranges of the zirconium, hafnium, and niobium alloys examined terminate at alloy concentrations of 0.1 to 0.2 at. pct. These metals form very stable oxides and their partial removal from solid solution in iron by impurity oxygen may be expected. We believe that the authors should have reported the procedure by which they distinguished the amounts of alloying elements in solution and in oxide. The diagrams pertaining to copper in Figs. 3 and 18 (lower) are almost certainly incorrect. Three recent investigations of this system38-40 all substantially agree on the solubility of copper in a iron, finding it to be much larger than that reported by Abrahamson and Lopata. The change of the lattice parameter with composition reported by Abrahamson and Lopata is too large by a factor of three to five, as seen by comparison with the findings of other investigators.41738 Moreover, the authors violate, in Fig. 18, the accepted Fe-Cu constitution diagram37 by ignoring the eutectoid at about 850°C.

Jan 1, 1967

By P. S. Rudman

Laves phases, AB2, are considered as Izerrzisub-stitutional solutions m1hich are defined by a one-for-truo replacement scheme. Atomic-size tnisfit is considered in terms of deviations of the ratio 2V°b/V°A from unity, where v° = atomic volume. A simple elastic model has been used to calculated deviations from "Vegard&apos;s law of atomic vol-umes". Comparison has been made between calculated and observed atomic-volume deviations fov 222 Laves phases. Agreement is generally very good although there ave some few exceptions which appear to be excusable in terms of electronic changes that ore beyond the scope of the present model. We can consider the formation of a binary sub-stitutional solution A-B from an A solvent as one-for-one replacements of A atoms by B atoms. As the atomic-size ratio deviates from unity, the solution becomes thermodynamically less stable and hence more restricted because of atomic-misfit strain energy. In accordance with our previously presented conclusion1 that the atomic volume, v, is in general the most appropriate measure of atomic size, the ideal size ratio for a binary sub-stitutional solution is vg/vA = 1. The Laves phases have been described by Berry and Raynor2 in terms of various stacking sequences of hexagonal layers of B atoms for the three structures MgZn2(C14), MgCu2(C15), and MgNi2(C36). To form the Laves phase of ideal composition AB, we start with complete hexagonal layers of B atoms in the appropriate stacking sequence and we remove, according to an appropriate scheme for each structure, two out of every four B atoms and replace the two removed atoms by one A atom. We thus might expect to find that the ideal size ratio for the Laves phases is 2v/B/ VA= 1. From this point of view, then, we call Laves phases hemi-substitutional solutions since we employ one-for-two replacements. By analogy with substitutional solutions we can expect for Laves phases that as the ratio 2VB/Va deviates from unity the phase occurrence will be more restricted. Laves3 has plotted the distribution of Laves phases as a function of the radius ratio, ?A/rB, and found that, while the distribution extended from 1.05 < rA/B < 1.50, the

Jan 1, 1965

By L. L. Newman

PUBLIC UTILITY GAS PRODUCTION IN 1802, William Murdock first used retort coal gas to light his house and the Boulton and Watt plant where he was employed. For the next three quarters of a century coal served as the principal raw material for the manufacture of city gas for general distribution. Coal continued to hold its predominant position for another half century after Prof. Thaddeus C. Lowe developed the first practical method of enriching water gas with cracked-oil vapors in an integrated operation. This position, however, was no longer maintained through the medium of direct carbonization of coal in retorts but as a result of using anthracite or coke as the generator fuel in carburretted water-gas machines. The early water-gas machines were extremely crude and the consumption of both oil and generator fuel was very high. However, the cost of installation was considerably lower than for any coal-gas system having the equivalent gas-making capacity, the labor involved was small, and the water-gas machine could be started up and shut down quickly. It thus proved very useful as standby equipment and in taking peak loads from the coal-gas plants. The flexibility of the water-gas machine, furthermore, made it possible to change the candlepower of the gas readily to suit the required conditions. Later, when calorific value replaced candlepower as the standard of gas quality, the water-gas machine was found to be equally flexible in keeping the city gas under complete and convenient control. No basic improvements were made in the Lowe carburetted water-gas process until 1898, when means were added to provide for regular reversals of the flow of steam through the fuel bed. By judicious proportioning of the quantities of up-run and down-run steam, it became possible for the operator to control the hardness and position of the clinker to a degree that previously had been unattainable. Also in 1898, the first by-product coke plant in America to supply city gas was built at Everett, Massachusetts. Later many other by-product plants, of greatly improved design and capacity, were built, but not primarily for city-gas production, chiefly because of the relatively high investment cost per unit of gas made. Cheaper plant construction has been the subject of serious study, and some progress is expected, but other factors, such as plant life,

Jan 1, 1953

By M. Garfinkle

LITERATURE data1&apos;3 have suggested that the resolved shear stress necessary to initiate slip in a particular slip system in tungsten single crystals is strongly dependent on the tensile orientation of the crystals. This orientation dependence is contrary to the critical resolved shear stress criterion. Because the Schmid factors for slip on particular {110}( I l l), {112}(Ill), or {123}(111) slip systems in a (100) oriented tungsten crystal are virtually identical to the respective Schmid factors for a (110) oriented crystal, slip should initiate on the same system in both orientations, independent of the values of the critical resolved shear stresses. Thus, it would be expected that, for a critical resolved shear stress model to hold, the proportional-limit stress for these two orientations must be similar. The expectation of similar proportional -limit stresses has not been borne out by reported experimental observations. Rose et nl.&apos; reported that the proportional-limit stress for crystals near the (110) orientation was 92,000 psi, approximately three times that of (100) oriented crystals (31,000 psi). Garlick and probst2 reported greater than a fourfold difference. Most recently, Beardmore and ~ull~ examined tungsten crystals with orientations along the edge of the standard stereographic triangle and showed a gradual increase in proportional-limit stress from 28,000 psi for the (100) orientation to 93,000 psi for the (110) orientation. Again, the difference was more than threefold. As has been emphasized by these investigators, the apparent gross variation of proportional-limit stress with orientation precludes any meaningful analysis of slip mechanics using a simple critical resolved shear stress relation. The purpose of the present communication is to report that, by use of refined strain-measuring techniques, the proportional-limit stresses for the (100) and (110) orientations are quite similar. Obviously, to determine accurately the value of the proportional-limit stress, which is by definition the stress at which nonlinear stress-strain behavior first occurs, the method of measuring strain must be capable of high accuracy. The investigators cited used as the measured elongation the crosshead displacement of the tensile machine. This method, however, introduces extraneous strain contributions from the load train. Because these extraneous contributions are considerable in the initial portions of loading (as has been well-documented in the literature) the proportional-limit stress measurement, dependent on the deviation of a line from linearity, can be significantly affected. During the course of a recent study, room-temperature strain was measured directly on several (100)-and (110)-oriented tensile specimens axially oriented within 5 deg of the desired direction. Each specimen was fitted with two foil strain gages mounted on opposite sides of the 0.08-in.-diam reduced section. The tensile specimens were loaded at a crosshead speed of 0.01 in. per min on an Instron Universal Testing Machine. Strain was monitored through an external bridge circuit in which the specimen strain gages comprised two arms. The bridge output was recorded against the applied load. A strain of 2 x 10"" could be readily detected by this method. Some specimens were subjected to conventional loading while the load for others was cycled between zero and continually increasing values until the first deviation from linearity was observed. The results of these methods were similar, and the stress at which nonlinear behavior occurred was considered the proportional-limit stress. The proportional-limit stresses measured in this study are approximately 5000 and 6500 psi for the ( 100) - and ( 110) -oriented crystals, respectively, a range of values almost a magnitude less than those reported previously. Representative curves are presented in Fig. 1. Because of the nature of the measurements made, the point of departure of a line from linearity is often debatable. While the load-strain curve for the (100) -oriented crystals made a relatively abrupt deviation from linearity, the curve for the (110) -oriented crystal was more gradual, so that the actual point of tangency may be at a lower load than reported. Thus, the difference in values for the proportional-

Jan 1, 1967

By George M. Humphrey

It is indeed a pleasure for me to have this opportunity to discuss with you a subject which I find infinitely interesting and intriguing - namely, world-wide iron ore supply and demand. We will be examining the following: (i) current iron ore production and requirements; (ii) the major ore producing countries; (iii) the seaborne iron ore trade; (iv) ore grades or types; and (v) future requirements. For those who may not be familiar with the iron ore mining industry, it may be useful to know at the outset that our industry has been plagued with overcapacity for the past seven years. The optimism which prompted substantial expansion of productive capacity in the early to mid-1970&apos;s has unfortunately proved to have been unfounded. I shall begin by describing where we are today as well as a little about how we got there. In the latter regard, it&apos;s not so much that historical knowledge will solve any of the industry&apos;s problems or provide clairvoyance with regard to the future. Rather it&apos;s a feeling on my part that some knowledge of the past will provide a useful perspective capable of enhancing our analysis of future trends. At the time of writing, the most recent year for which we have definitive world-wide iron ore production and consumption statistics is 1980. In that year the world consumed approximately 859 million metric tons of iron ore to produce approximately 510 million metric tons of primary iron consisting of 502 million tons of pig iron and 8 million tons of sponge iron. Crude steel production for the same period attained a level of 719 million metric tons. Because it is possible in today&apos;s world to produce steel without consuming iron ore simply by melting scrap, the key statistic insofar as iron ore demand is concerned is primary iron production. In 1980 the ratio of iron ore consumption to primary iron production was 1.68:1.00. The comparable ratio over the past seven years has varied from 1.63 to 1.87 and averaged 1.72:1.00. All the same, as a practical matter crude steel production and iron ore consumption tend to parallel one another closely, and for the time being a good rule of thumb is that to produce an average ton of crude steel requires 1.20 tons of iron ore. Let&apos;s turn our attention now to the regions where the 859 million tons of iron ore necessary to support 1980 world-wide iron and steel production were produced. Not surprisingly, most of the ore was produced in the same region where it was smelted. In round numbers 65% of the world&apos;s iron ore production is currently consumed in the same general region as it is produced, while 35% enters the seaborne trade and is transported in ocean vessels to a more remote consuming area. Approximately 85% of the world&apos;s seaborne iron ore trade is directed to the Western European and Japanese markets, both of which are almost entirely dependent on off-shore sources for their mammoth iron ore requirements. The following tabulation lists, in order, the twelve leading iron ore producing countries in 1980 as well as their percentages of total and free-world production; in addition their export potentials are presented. As a group these countries accounted in that year for 89% of world-wide production which stood at 871 million tons. Leading World Iron Ore Producing Countries [ ] One will first note that world iron ore production is dominated by the top four producers - namely, the U.S.S.R., Brazil, Australia and the U.S.A. - which together accounted for nearly 60% of total 1980 production. Of these four major producers the U.S.A. and the U.S.S.R. produce almost exclusively for consumption in their own regions, whereas Australia and Brazil produce primarily for the seaborne export trade. In fact Australia and Brazil accounted for about 50% of all seaborne iron ore trade in 1980! It is also interesting to note that Australia, Brazil, the U.S.A. and Canada accounted for nearly 60% of free world iron ore production in 1980. Once again the importance of Australia and Brazil shows itself, with their share alone of free world production reaching 35%. As has already been noted, a significant 35% of the world&apos;s iron ore production in the year 1980 was

Jan 1, 1982

By R. W. Snyder, H. J. Ramey

This paper presents the results of applying the Buckley-Leverett&apos; displacement theory to petroleum reservoirs consisting of a finite number of layers. The layers are assumed to communicate only in the wellbores, and the reservoir may be represented as a linear system. Most previous investigations of this nature were limited by assumptions and by inconsistent calculation techniques. This study improves on previous work by applying the Buckley-Lev-erett displacement theory to a noncommunicating layered system where permeability, porosity, initial saturation, residual saturation and relative permeability vary from layer to layer in a logical and consistent manner. Gravity and capillary-pressure effects are neglected. A modification of the Higgins-Leighton calculation method was used in this study. Waterflood predictions were made with all properties varying, and then with only permeability varying using several inability ratios. These results were compared with the Stiles and Dykstra-Parsons predictions. It is shown that the latter methods generally give poor values for the breakthrough recovery and pessimistic predictions for the performance after breakthrough. Similar results were obtained for a gas-displacement case. lNTRODUCTION Field experience with immiscible displacement usually shows constant producing conditions until breakthrough of the displacing fluid. Then oil production continues at increasing displacing-to-displaced fluid ratios until the economic limit is reached. Three different ideal mechanisms are known that will produce this behavior: (1) relative permeability effects as described by Buckley-Leverett frontal advance theory,&apos; (2) vertical stratification as considered by Stiles,2 Dykstra and Parsons5 and others and (3) different path lengths involved in areal (two-dimensional) flow between wells as described by Dyes et al.4 Without question, a combination of these factors modified by formation heterogeneity and other known and unknown factors actually does control the behavior of real systems. This paper presents results of an investigation of certain factors that should affect performance but which have received little attention to date. In 1944, Law5 demonstrated that porosity and perme- ability are often found to have normal and logarithmic-normal distributions, respectively. throughout cored intervals in natural formations. This led to the concept of the noncommunicating, multilayered reservoir model for immiscible displacement. This model assumes that the reservoir is composed of a number of layers that communicate only at the wellbores. Each layer is individually homogeneous, but may be different from every other layer. Stiles&apos; presented one of the earliest applications of this model to waterflood performance. In addition, Stiles assumed that the initial saturations and relative permeabilities were the same for each layer, porosity was the same. displacement was piston-like, fluids were incompressible and injection into each layer was proportional to that layer&apos;s permeability capacity (permeability-thickness product). The last assumption would be true if the mobility ratio for the displacement were unity.21 Dykstra and Parsons" used the same model as Stiles, but rigorously included mobility ratios other than unity for piston-like displacement. Dykstra and Parsons used their general result to produce charts for log-normal permeability distributions between layers. Similarly, Muskat6 Pub1ished analytical solutions for linear and exponential permeability distributions. In 1959, Roberts&apos; described a scheme for calculating water-drive performance for the noncommunicating, layered reservoir model which considered two-phase flow in the displaced region. Roberts used the same model and assumed that the injection rate into a layer was proportional to that layer&apos;s permeability capacity, but that flood front locations could be evaluated from the Dykstra-Parsons results. These assumptions are inconsistent, and a material balance cannot be maintained except for a mobility ratio of unity. At the same time, Kufus and Lynch8 coupled Buckley-Leverett displacement theory with the layered model to provide an improvement of the Dykstra-Parsons method that was consistent. In 1960, Higgins and Leighton9 resented a numerical method for calculating waterflood performance also considering two-phase flow in the displaced region. The result was used to investigate variation in absolute permeability and oil viscosity. An excellent, detailed history of using the noncomrnunicating, layered reservoir model was presented by Nielsen.&apos;" The preceding techniques (and many related ones) were similar in that differences in initial saturations, residual saturations and relative permeabilities from layer to layer were neglected. It is well known that the irreducible water saturation is an important function of absolute permeability. Calhoun11 showed that the irreducible water saturation

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" &apos; also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder&apos;)"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder&apos;s results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13&apos; and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*&apos; " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.&apos;" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.&apos;&apos;&apos; The experiments which will be described in this paper pertain to: (a) the effect of a crystal&apos;s shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By P. Somasundaran, D. W. Fuerstenau

The length of the collector is found to influence the flotation of the mineral even at incipient conditions, which are below the concentration at which interaction at the solid-liquid interface begins to take place to form hemi-micelles. To study this dependence, concentration for incipient flotation of quartz was determined as a function of pH with collectors of various chain lengths. The observed effect of chain length on flotation is ascribed to that of collector adsorbed on the bubble surface. In previous studies, it was shown that at low concentrations the alkyl collector ions adsorb at the solid-liquid interface as individuals.&apos;&apos;2 At higher concentrations, the collector ions adsorbed at the solid-liquid interface associate with each other to form two-dimensional aggregates called hemi-micelles. Above the hemi-micelle concentration, the length of the hydrocarbon chain is extremely important since the hydrocarbons are in effect removed from water during the association, making the energetic conditions more favorable for adsorption at the interface. Because of this enhanced adsorption, one observes a very rapid increase in flotation associated with the hemi-micelle formation at the solid-liquid interface. However, a dependence of flotation on the chain length at concentrations below that required for hemi-micelle association was also observed,&apos; and this cannot be explained by the above mechanism which postulated hydrocarbon chain interactions only at the solid-liquid interface. This prompted an investigation into other possible reactions of the hydrocarbon chains and an examination of the conditions at the bubble surface involved in the flotation system and how these observations might explain the reactions at the solid-gas interface which cause the particle-bubble attachment required for flotation. To obtain more information on chain length effects, flotation, under incipient conditions, was tested by vacuum flotation techniques. The collector-concen-tration-pH relationships for flotation of quartz with alkyl ammonium acetate collectors was delineated by observing the pH at which quartz particles begin to float to the liquid surface. By investigating flotation as a function of pH, it was also possible to study the effect of neutral molecules on incipient flotation conditions, since the aminium ions hydrolyze to amine molecules at higher pH values. EXPERIMENTAL WORK Brazilian quartz specimens were crushed and sized, and the 270 x 400 mesh fraction was used for flotation studies. The samples were leached with concentrated hydrochloric acid until no coloration of the acid occurred. The leached material was washed free of chloride ions and stored in distilled water. The vacuum flotation technique developed by Schuhmann and prakash3 was used to determine the critical pH-concentration curves. This method, which can be used to delineate conditions for incipient flotation, is fairly simple and rapid. About 0.5 gm of 270 x 400 mesh quartz was placed in a 100 ml graduated cylinder which was then filled to the 100 ml mark with the collector solution made from high-purity alkyl ammonium acetate salts. The water used for the test was conductivity water saturated with air that had been passed through a cleansing train consisting of Drierite, Ascarite, a water wash bottle, and a trap. After the pH was adjusted, the cylinder was then conditioned for thirty minutes. In the tests where an acid pH was desired, sufficient acid was added before the collector solution to avoid any effect due to slow desorption of collector from the quartz surface. After conditioning, vacuum was applied to the system and the flotation or nonflotation of the quartz was noted. The pH at which the quartz particles began to float to the liquid-gas interface was taken as the critical PH. Critical pH curves were thus determined for different concentrations of the various collectors. Hallimond tube flotation data were taken from the authors&apos; previous publication1 for correlation with that from the vacuum flotation. RESULTS AND DISCUSSION The results of vacuum flotation studies for determining critical pH-concentration curves, i.e., curves which delineate conditions for incipient flotation, are shown in Fig. I. In generaI, all the curves exhibit an upper and lower pH limit between which flotation will

Jan 1, 1969

By Leendert de Witte

Conventional resistivity logs consisting of a short normal, a long normal, and one or more long lateral curves do not give data that allow a complete quantitative interpretation in beds thinner than 20 ft. Reservoir rocks usually exhibit zones of continuous homogeneity of quite limited thickness where the long lateral curves become useless because of adjacent bed effects and boundary phenomena. If the beds are 12 ft or thicker, the short and long normals may be used for qualitative interpretation, which can be streamlined by the application of simplified departure curves. For beds of a thickness less than twice the long normal spacing, this procedure breaks down. The combination of the limestone curve, the later-olog or guard electrode log, and the microlaterolog permit quantitative interpretation for beds that are at least 10 ft thick, provided the mud resistivity and the hole diameter are known with sufficient accuracy. For beds thinner than 10 ft, combinations of the microlaterolog with short spaced laterologs and pseudo laterologs appear to be promising. Interpretation of these curves again requires the application of simplified departure curves. Resolution of various possible combinations was analyzed using departure curve data calculated on the Whirlwind I computer at the Massachusetts Institute of Technology. A field example is shown using the microlaterolog-microlog combination, and the combination of a 6-in. modified laterolog plus a 6-in. pseudo laterolog. INTRODUCTION For the purpose of quantitative interpretation of resistivity logs in porous formations, we want to obtain two essential quantities from the logs, namely, the true resistivity of the undisturbed formation, Rt, and the resistivity of the part of the formation invaded by mud filtrate, Rt. The apparent resistivities of all conventional logging devices are functions of these two parameters and are also influenced by a third unknown parameter, the diameter of the invaded zone, d. It has been shown&apos; that from the normal curves alone it is impossible to arrive at a unique solution for the three unknowns, Rt, R1, and d1. In very thick homogeneous beds, if invasion is not too deep, we can obtain a fair approximation to Rt from the long lateral curves and then use the two normal curves to find Rt and d1 Even under the most favorable conditions, the resolution of this system is not very good. The short normal does not give a reasonable approximation to R1 unless invasion is very deep (dl>16 hole diameters). For very deep invasion, however, the long laterals no longer approximate Rt. For bed thickness between 20 and 40 ft, the long laterals are affected appreciably by the adjacent beds; and the curves are distorted by boundary anomalies to the extent that they lose their quantitative usefulness in most cases. For the same bed thicknesses, the normal curves still function reasonably well. Although it is impossible to find unique solutions Lor R1 and Rt using the normal curves alone, we can obtain a reasonable approximation for the ratio R1/Rt through the use of simplified departure curves. This fact was brought to our attention by A. J. de Witte, geologist with Continental Oil Co. As the magnitude of Rl/Rt is a major clue to the presence of oil in formations, this method can be used to good advantage for qualitative analysis and will be discussed in somewhat greater detail. With the aid of suitable bed thickness corrections, the analysis of the normal curves may be used for bed thicknesses larger than 12 ft. For thinner beds, the method rapidly loses its resolution; and we have to resort to different types of resistivity logs if we want to attempt to analyze the curves quantitatively. The inadequacy of conventional resistivity curves in thin beds is far more serious than generally realized. Fig. 1 shows a conventional E. S. with a 16-in. and 64-in. normal and a 16-ft lateral through a section of Lansing-Kansas City lime, in comparison to a guard electrode survey through the same section in a neighboring well. The porous zones, which show up as low resistivity breaks on the guard electrode log, are completely masked by adjacent bed effects and boundary anomalies on the conventional curves. Even the short normal shows most of the porous Zones only as Vague deflections and in many cases fails to register Their

Jan 1, 1955

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc at temperatures below 200°C has been studied using both single crystal and polycrystal samples. Anomalous results were obtained for single crystal samples, the data indicating that in some cases grain boundary diffusion predominated. These anomalous results are presumed to be due to low angle lineage boundaries in the single crystals. When volume diffusion occurred in either single or polycrystal samples, the values for the diffusion coefficient were as much as several orders of magnitude larger than would be expected from high temperature data. ONSIDERABLE work has been done on self-^-*diffusion at temperatures in the neighborhood of two thirds of the melting temperature (in OK) and higher, but very little has been done at lower temperatures. This is particularly true of self-diffusion in single crystals. This paper reports work on self-diffusion in zinc at temperatures below 200 °C where both polycrystalline and single crystal samples have been used. The measurements were made using both the sectioning and absorption techniques. The experiments on diffusion at low temperatures were initiated primarily for three reasons: to obtain data from single crystal diffusion covering a wide range of temperatures, to obtain values of the activation energy for grain boundary diffusion, and to obtain, if possible, a lower limit to the temperatures at which the absorption technique may be used. It is possible to determine whether volume or grain boundary diffusion predominates at low temperatures by analyzing the manner in which the concentration of the diffusing atoms varies with the depth of penetration. The analysis is possible only for the sectioning technique. For volume diffusion and for the boundary conditions of the present experiment, the curve of the logarithm of the concentration, C, vs the square of the penetration depth, x, is a straight line with the slope proportional to — 1/D. If grain boundary diffusion predominates, Fisher&apos; has shown that a curve of In C vs the first power of the penetration depth should be a straight line. This linear dependence of concentration on depth has been observed experimentally by several investigators. (See, for example, refs. 3 and 4.) Following Fisher&apos;s analysis, the grain boundary diffusion coefficient can be written as where 8 is the grain boundary width, D, is the volume diffusion coefficient at the temperature involved, t is the time of diffusion, C is the concentration of diffusing material, and x is the depth of penetration. A more general analysis employing the same model as Fisher&apos;s but with fewer assumptions has been given by Whipple.&apos; In contrast to Fisher&apos;s analysis the more general analysis of Whipple does not always yield a straight line relation between In C and x. Recently Turnbull and Hoffman have discussed both analyses and have applied the Fisher-Whipple model to a more refined dislocation model of the grain boundary. They have also discussed the possibility of a large effect of grain boundary direction on diffusion. In the case of the absorption technique, for which results are also given, one simply gets a value for the diffusion coefficient with no indication of the predominating mechanism. Experimental Techniques Single crystals of 99.99+ pct Zn were grown using a modified Bridgman method. Polycrystal samples were prepared in three grain sizes (small, about 4 mm2; medium, about 9 mm&apos;; and large, about 25 mmz) by quenching, air cooling, and furnace cooling. The grains of the polycrystalline samples tended to be columnar, with some preferred texture such that the c-axis was inclined at about 20" to 25" from the normal to the diffusion face, particularly in the medium and large grain size samples. The samples were cut from the rod, polished, and heavily etched, and faces cut accurately parallel using a jeweler&apos;s lathe. They were again etched to remove the lathe smear and annealed for 3 hr at 250" to 300°C. After annealing, they were etched, examined, and the orientation determined by Laue back reflection photographs. They were then electroplated with Zn. The plated surfaces were examined for uniformity; nonuniform coatings were removed by etching and the samples replated without additional preparation. For the diffusion anneals, the samples were placed in pairs, with active faces together, in evacuated Pyrex tubes. Constant temperature baths were used, and the variation in temperature did not exceed ±l°C, Diffusion runs were made at l00°,

Jan 1, 1957

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-&apos;, a lo-&apos;-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10&apos; cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell&apos;s law that where = critical angle, n - index of refraction of air, n&apos; - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,&apos; and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert&apos;s law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,&apos; where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

Because common salt, sodium chloride, is necessary to all animal and much plant life, it is probably the most widely used of all mineral commodities, except for water. Nevertheless, of the total salt consumed, only 7% is used for food, including animal food. Two-thirds of the total is used as chemical raw material, principally for making such basic chemicals as chlorine, caustic soda, and soda ash. Other uses are for road thawing (16%) and water softening. Some 162.5 million tons of salt were used, worldwide, in 1972 (Table 15.4F.1). Production is from bedded salt deposits, salt domes, and evaporation of brines, including solar evaporation of seawater. Production is worldwide from at least 20 countries, of which the United States, China, USSR, the United Kingdom, and West Germany are the leaders. Consumption increases about 7 % annually. Reserves are plentiful: Other important sodium salts are soda ash (sodium carbonate) and salt cake (sodium sulfate). Soda ash comes mainly from the Solvay process (70% ) , which uses salt, limestone, and ammonia as raw materials. A large and growing portion of United States production is from mining large bedded deposits of trona, a natural hydrated sodium carbonate and bicarbonate found in Wyoming, and from brine evaporation in California. Soda ash is used for glassmaking, phenol, soap, detergents, and bleaches. Half of the United States salt cake used is a byproduct from rayon manufacturing. The other half comes from brines and playa lakes in California, Texas, and Wyoming. Salt cake is used mainly for papermaking. ACKNOWLEDGMENT Appreciation is expressed to William B. Dickson, president, Salt Institute. [ ]

Jan 1, 1976

By Paul Averitt

In spite of recent trends in the United States toward construction of steam generating plants near mine mouths, and toward use of high-voltage direct current for long-distance transmission of electricity, coal in substantial amounts is being transported over relatively long distances to serve specific needs. As coal is a low-cost bulk commodity which is more suitable for use near the point of origin, some of these long hauls are of considerable interest because they show what can be done under the pressure for more and more coal to support industrial and economic growth. Japan has an Insatiable Appetite for Coal Perhaps the longest U.S. coal journey begins in the east Appalachian Basin of southern Pennsylvania, eastern West Virginia, and southwestern Virginia. High-quality coking coal mined in these areas is shipped by rail to Baltimore, Md., and to Hampton Roads, Va., where the coal is reloaded on freighters for shipment primarily to western Europe and Japan. In 1967, shipments of coal to western Europe totaled 19 million tons, and shipments to Japan totaled 12 million tons. Japan also imports coal from Australia, the U.S.S.R., Canada, Poland, the People&apos;s Republic of China, and to a lesser ex- tent from several other countries. In an effort to solve long-term needs, Japanese steel interests have contracted for the purchase from the Kaiser Steel Corp. of 51 million long tons of coking coal over the period 1970 to 1985. The coal will come from the Kaiser Steel Corp. mine near Fernie, British Columbia. This arrangement will reduce Japan&apos;s future dependence on Appalachian Basin coal.

Jan 10, 1969

By Henry Kreisinger

IN evaluating coals as steaming fuel on the basis of chemical and physical properties of the coals, the only properties that can be used are those for which the methods of determination are well established and standardized, and those that affect all methods of burning the coals in the same way. The discussion is written from the standpoint of the coal consumer. The production of steam is the largest field for the use of coal. It includes stations for generating electric power, central heating plants, industrial power plants where steam is used for power generation, factory processes and heating. The field also includes steam locomotives. Small house-heating boilers are not included in this field because such small boilers generally burn specially prepared domestic fuel. The plants using the steam coal are equipped to burn the coal when fired by one of the three general methods: namely, hand, stoker, and pulverized coal. The hand firing is now restricted to small plants and to locomotives. Central stations and larger industrial plants use either stoker or pulverized-coal firing. Some locomotives also use stokers. Pulverized-coal firing has been tried in locomotives but so far its adapta-tion to this use has been handicapped by practical difficulties. The coals used for steaming purposes are generally of the bituminous and semibituminous classes, with volatile matter ranging from 15 to 35 per cent. Coals belonging to these classes are produced in many parts of the United States and form by far the largest part of the total coal production of the country. The value of any coal as fuel for steaming purposes depends on the following factors

Jan 1, 1935

By M. F. Fogler

An attempt to duplicate Rawdon and Mutchler&apos;s experiments showing a reversal of hardness with continued rolling gave negative results, indicating that the phenomenon is not general but depends, probably, on local conditions of rolling. IN A recent paper, Rawdon and Mutchler1 gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between-the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925

By W. F. Holbrock

IN a previous paper1 a method for the measurement of the compara-tive desulphurizing power of slags was described and data, were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include Tags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO sings over the range 147.5° to 1525° C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.S per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphuriz-ing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in holes in a section of all electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small varia-tions in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups -in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO.

Jan 1, 1938

By Franklin J. Stermole

INTRODUCTION Economic evaluation of an open pit mine is similar to the economic analysis of any major investment project in any industry. It requires (1) taking into account all of the costs and revenues that are estimated to be incurred over the economic life of the project; (2) crediting the project with all the tax savings and tax credits that will be realized over the project life from tax deductions and credits related to various project costs; (3) charging the project with all taxes to be paid on taxable income over the project life; and (4) properly accounting for the time value of money for all project costs, revenues, taxes, tax savings, and tax credits when making the overall project economic evaluation. These considerations must be taken into account for any valid method of economic analysis such as discounted cash flow rate of return (DCFROR) or net present value (NPV) analyses. All economic analyses fall into one of two categories. ( 1 ) comparison of income-producing alternatives, or (2) comparison of service-producing alternatives. The analysis of alternatives in either of these categories can be made by using correctly any of five basic economic evaluation approaches which are. ( 1 ) present value, annual value, (3) future value, (4) rate of return (ROR) , and (5 ) break-even analysis. Of these evaluation techniques, DCFROR and NPV analyses are used most widely for evaluating income-producing alternatives while present worth cost and equivalent annual cost analyses are used most often for the evaluation of service-producing alternatives. In this chapter income- producing alternative analysis is emphasized, so DCF- ROR and NPV are utilized for evaluating the case studies presented.

Jan 1, 1979

By J. B. Ackerman, J. D. Miller

Alunite [KA13(S04)2(OH)6] is a promising non-bauxitic aluminum resource, the domestic reserves of which are estimated to be 800 x 106 tons at 35 percent alunite. The major gangue mineral associated with alunite is quartz. The thermochemical process that has been developed for treatment of this ore does not provide for the initial removal of gangue prior to processing. In this regard, it may be desirable to concentrate the ore to gain significant technical and economic advantages. Experimental results indicate the effectiveness of an oleic acid flotation technique and exemplify the problems encountered in fine particles processing. These results show that the quality of separation studied as a function of temperature, collector addition, and depressant addition is dependent on the degree of liberation achieved during size reduction. At coarse grinds the quality of separation was limited by the presence of locked particles while for finer grinds where more extensive liberation is achieved, better separations were obtained. The degree of liberation for each size interval was determined by an SEM/energy dispersive x-ray technique and found to be independent of the extent of size reduction, suggesting that liberation occurs by indiscriminate fracture and not by detachment. Up to 89 percent liberation was realized for a minus 400 mesh grind. Under these circumstances, the quality of separation appears not only to be limited by the remaining locked particles, but, also, by contamination of the alunite concentrate with fine quartz gangue (< 2µm). The best separation for the minus 400 mesh grind was a rougher recovery of 88 percent with a grade of 65% alunite at 50°C.

Jan 1, 1980

By J. D. Miller, R. J. Smith

The hot water process for Utah tar sands differs significantly from that used for Canadian tar sands due to inherent differences in respective bitumen viscosities and the nature of bitumen-sand association. These differences have led to the identification of certain design criteria necessary to achieve satisfactory phase disengagement during digestion (Sepulveda and Miller, 1978; Misra and Miller, 1980). Subsequent flotation of digested tar sand is a subject of current attention and is considered in this publication for the Asphalt Ridge deposit. Although contact angle measurements of solvent extracted Asphalt Ridge bitumen indicated moderate hydrophobicity, air bubble attachment to the bitumen concentrate is not possible. This surprising result suggests that flotation separation is dependent on air bubble entrapment rather than on air bubble attachment due to surface hydrophobicity. The entrapment of air bubbles in the bitumen was apparent from examination of the bitumen concentrate, especially at lower flotation temperatures. A factorial design of the major operating variables in flotation separation indicated that the quality of separation was significantly dependent on the flotation temperature and to a lesser extent on the degree of agitation. For a flotation temperature of 77°C a recovery of 96.7% was realized at a grade of 61.0% bitumen. The improved separation at higher flotation temperatures was found to be due to the decrease in bitumen viscosity resulting in more effective rejection of coarse sand from the concentrate. This research effort, which has been sustained for the past six years at the University of Utah, is being continued to provide necessary design data for the construction of a pilot plant to treat Utah tar sands.

Jan 1, 1982