Search Documents

By AIME AIME

NO other man now on the Institute's Board has a record of long service to his professional society comparable with that of Karl Eilers. He joined in 1888; he was a Councilor as far back as 1909, a Vice-President as early as 1912, and for the last ten years has been continuously a Director and Treasurer. It seems fitting, therefore, that he is the only member of the present Board that is also an Honorary Member of the Institute. Karl Emrich Eilers was born near Marietta, Ohio, Nov. 20,,1865, which makes him 71 years old. Columbia School of Mines gave him his E.M. in 1889, after which

Jan 1, 1937

By Daniel M. MacNeil, Carle R. Hayward, Raymond L. Presbrey

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By J. L. Gregg

A study of copper-base and silver-base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.l This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys. Copper Alloys For the purpose of making a rapid survey of copper alloys that might show useful dispersion-hardening phenomena, various alloys were prepared containing 3 per cent. of additional elements added in such proportion that possible compounds could be formed without an excess of either added element. These alloys in the form of rolled or forged pieces were quenched in water from a temperature of 871" C. (1800" F.) and subsequently aged at various lower temperatures for l-hr. periods. The comparison of the Rockwell hardness of the quenched alloys with the maximum hardness of the alloys after aging was used as a measure of the dispersion hardening. Table 1 shows the Rockwell "E" hardness 1/8-in. ball, 100-kg. load) of the quenched alloys, together with the maximum hardness resulting from aging. The reheating temperature given in this table is the aging temperature at which maximum hardness resulted from a l-hr. sojourn. From this table it may be observed that only the silicide alloys showed significant dispersion hardening. Of these, the only one not described by Corson is the Cu-Be-Si alloy. This alloy contained 1.35 per cent. beryllium and 1.78 per cent. silicon, which is approximately equivalent to 3 per cent. Be2Si. It had a yellow color and scaled much less than the other silicide alloys upon heating. It could be worked easily either hot or cold but hardened very rapidly on cold working. The annealed alloy upon drawing from a diameter

Jan 1, 1929

By Daniel M. MacNeil, Raymond L. Presbrey, Carle R. Hayward

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By J. L. Gregg

A study of copper-base and silver-base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.l This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys. Copper Alloys For the purpose of making a rapid survey of copper alloys that might show useful dispersion-hardening phenomena, various alloys were prepared containing 3 per cent. of additional elements added in such proportion that possible compounds could be formed without an excess of either added element. These alloys in the form of rolled or forged pieces were quenched in water from a temperature of 871" C. (1800" F.) and subsequently aged at various lower temperatures for l-hr. periods. The comparison of the Rockwell hardness of the quenched alloys with the maximum hardness of the alloys after aging was used as a measure of the dispersion hardening. Table 1 shows the Rockwell "E" hardness 1/8-in. ball, 100-kg. load) of the quenched alloys, together with the maximum hardness resulting from aging. The reheating temperature given in this table is the aging temperature at which maximum hardness resulted from a l-hr. sojourn. From this table it may be observed that only the silicide alloys showed significant dispersion hardening. Of these, the only one not described by Corson is the Cu-Be-Si alloy. This alloy contained 1.35 per cent. beryllium and 1.78 per cent. silicon, which is approximately equivalent to 3 per cent. Be2Si. It had a yellow color and scaled much less than the other silicide alloys upon heating. It could be worked easily either hot or cold but hardened very rapidly on cold working. The annealed alloy upon drawing from a diameter

Jan 1, 1929

By N. H. Emmons

The work of a consulting engineer or manager, when controlling mining-operations, requires that he have all the information concerning the mine in as concise a form as possible, and as the ore-reserves and their depletion and enlargement are the vital points to be studied, it is well to have the records kept up to date and in some convenient form. The present paper describes a method adopted by me, which shows in a very clear manner the ore-reserves in a mine. The case illustrated is that of a vein near enough to the vertical for the vertical elevation of the mine to be the main working-map. A flat ore-body would be represented on a similar plat, but instead of the horizontal thickness of the vein being shown in the circles, the vertical thickness would be inserted. Fig. 1 represents an ideal longitudinal elevation of a mine, plotted in the ordinary way, using 100-ft. blocks and section-lines. In a mine where the block-numbers are posted by the engineer underground, the system of keeping the ore-tonnages extracted from the different blocks is easily maintained, and the actual tonnages of ore extracted can be kept so that the surveyor can have a check on his estim'ate from time to time. The ore-reserve sheet, Fig. 2, should be the same size as the map it is to accompany. Each square is used for the description of the ore-reserve in the block it corresponds to on the elevation. Where the section-lines cross the levels a circle is drawn, in which are written the midths of ore at that point, these widths being used in the calculations of each block cornering in the circle. It has been found convenient to show the figures in black in the lower half of the circle when the actual widths of ore are known, and when it is necessary to make up the figures of probable ore, as at the time of making

Jan 1, 1913

By C. H. Green

Recently two papers on the structure of eutectics were read before thc British Institute of Metals, one by F. L. Bradyl and the other by A. Portevin. 2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches, the writer has been working along the same line for some time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which separate out simultaneously or alternately. From the surface pattern, the eutectic means a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the proeutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 1, 1925

By A. Hamilton Garner

The occurrence of oil seepages in Venezuela has been known since the early days of Spanish occupation. It was not until 1912, however, that any serious exploration work was undertaken. In that year, the Caribbean Petroleum Co., then a subsidiary of the General Asphalt Co., employed a large staff of geologists to make a systematic survey of large areas in eastern and western Venezuela, selecting the most desirable localities out of the immense area covered by the Valladares concession. This preliminary work was completed in the fall of 1913, and in February, 1914, the company completed its first commercial well at Mene Grande. Development work has progressed slowly, for various reasons, but petroleum in quantity has been encountered in nine widely separated localities. The Mene Grande field has been put on a producing basis and approximately 4,000,000 bbl. of oil is being shipped annually. Increasing quantities of oil are now being drawn from El Mene and La Rosa. In the light of these developments, the world's need for oil reserves, and the proximity of Venezuela to the United States, American capital is being attracted more and more to Venezuela. Although considerable careful geological work has been done in Venezuela by the various oil companies now operating, most of the data is buried in the company files, and the published literature has been extremely meager. The most valuable contribution to date has been a map and report by Jahn, which, as it was printed in Spanish, is not generally available to the American oil public. Venezuela, located in the northwestern part of South America on the Caribbean Sea, lies between l° and 12° north latitude. Its principal

Jan 1, 1925

By Walter S. Larsh

The Ruth orebody, so far developed, is roughly oval in plan, major and minor axes about 1600 ft. (457 m.) and 1200 ft. (365 m.) respectively, average thickness about 120 ft. (36 m.), and with a general dip of about 15" to the northwest. According to the generally accepted theory, the ore is a secondary enrichment of the porphyry due to leaching in situ by meteoric waters. Copper occurs as chalcocite, chalcocite coating pyrite, and a little chalcopyrite. The leached zone, or capping, covering the ore varies in thickness from 110 to 540 ft. (33 to 164 m.), average about 410 ft. (124 m.). The ore is blue gray in color, and the capping, light yellow to brown. Ore was first discovered in quantity in the workings from the Ruth shaft, now caved. Further development work was done by churn drills, and the outline of the orebody, as stated above, determined in this manner. Drilling is still being carried on. The porphyry area is entirely surrounded by sedimentaries, limestones, and shales; and, in so far as the underground workings have shown, the porphyry itself, the sedimentaries' near the contact, and the country underlying the ore (igneous or sedimentary) is very soft, heavy, and in places swelling ground. All openings have to be carefully and stoutly timbered, and, after once driven, they have to be constantly eased off and repaired. The mine Is at present served by two shafts, the Star Pointer, the main working shaft, a vertical, and the Ingersoll, an incline used for waste and material. The two shafts are about 2600 ft. (792 m.) apart, connected on the 500 level; a connection is now being driven on the 600 level. (Dec., 1917. This connection is now completed.) The 300 level, which is finished, and the 400 level which is nearly completed, are accessible only from the Ingersoll and connections with the 500 level. The 300 level was developed for and mined by the shrinkage stope system, similar to that used successfully in the Ray Consolidated property.

Jan 1, 1918

By A. Eilers

Although the process to which I refer in this paper has been in successful operation for nearly five years, during which time it has been introduced, superseding all other processes having in view the same end, in almost every lead refinery in the country, no description of it, giving economical data, has ever appeared in print, nor has the process been known in its details to any considerable number of engineers beside those conducting it at their works. A discussion of this subject at the present time becomes especially interesting in view of a late publication in the Prussian ministerial organ for Mining and Metallurgy, by Dr. Wedding, in which the method of treating the zinc-silver-lead alloy by distillation, as finally settled upon at Tarnowitz, is very minutely and fully described. It is the more interesting, because in that article reference is made to the American method in an unfavorable light, while, at the same time, it is clear from the article itself, that the most important details of the process, besides the one that it is conducted in black-lead retorts, mere not at all understood. In publishing herewith the details of our American method, one of my objects is to invite comparisons between our simple and direct process and the elaborate one at Tarnowitz. In extracting the silver from work-lead by means of zinc, it is always the intention, in this country, to obtain a zinc-crust so rich in silver that the rich lead resulting from subsequent distillation

By W. G. Scott

Since devising the incline top-slicing method in use at the Coronado mine,l I have had numerous inquiries as to how the same system could be adapted to larger orebodies. Based upon our experience here, I have outlined below some suggestions for its application to orebodies of larger size. Modifications and extensions, of course, would have to be made to take care of different dimensions and irregularities. In order that one may have a better understanding of the scheme, a brief description of the Coronado method will be given first. CORONADO METHOD The portion of the Coronado vein that is worked by the slicing system ranges from 20 to 40 ft. (6 to 12 m.) in width. Preparatory work in this orebody consists of driving sub-levels every 55 ft. (1 6.77 m.) vertically, or in multiples of 11 ft. (3.36 m.) (which is the height of a slice). These levels are usually driven along the hanging wall until the end of the orebody is reached. Crosscuts, at right angles to the strike, 50 ft. (15.24 m.) apart, are then run from wall to wall, or until the lean ore is reached. They are run in the middle of the block, which is 50 ft. in length and the width of the vein. The crosscut on the hanging-wall side is extended in the wall a short distance for a manway and timberway raise. This raise is carried up in the wall to the sub-level above, leaving a pillar about 5 ft. in thickness between it and the vein. Connections are made every 11

Jan 1, 1918

By V.F. Marsters

Seepages of oil in Ecuador have been known for many years. The locality first to receive attention, and still worked in a modest way, lies on the north shore of the Santa Elena peninsula, between La Puntilla and Salinas. Operations mere first conducted largely by local cdpital. Later, foreign companies acquired large blocks of land, where they have done considerable drilling. For details concerning present drilling activities in Ecuador, we are indebted to Leon Price, an Ame~ican resident engineer of Ecuador. The information solicited came to the author through the office of the American Consulatell with permission to use it. The coastal plain bordering the Province of Tumbes, Peru, continues to the northeast, but narrow on passing the Zarumilla River. From this point northward it widens toward Santa Rosa. In fact, the pampas, as shown on the official Wolf map, correspond fairly well to the areal extent of tbe coastal plain as far as Guayaquil. This is shown in a general way on the accompanying map. The author understands that the Guayaquil enlbayment is bordered on all sides by the coastal plain, as recognized at Tumbes and farther southwest, and that it can be followed without a break as far north as Palmar. This view is supported by the mapped area regarded by Mr. Price as favorable or possible oil territory. Moreover the islands in the Gulf of Guayaquil are the same geologically as the coastal edge, being composed of Tertiary sediments. The author understands also that Tertiary formations occur north of Palmar. According to a report by Mr. Cardon, of Guayaquil, Tertiary sediments are exposed in the region of San Francisco and extend to and beyond Pta. Calera. There is also reason to believe that at least the lower part of the valley of the Santiago River is occupied by Tertiary sediments, ~~hich probably border the const line and extend into the River Mini l)nsin, and into Colombia. On the south coast there are many seepages, most of them near the inner edge of the coastal plain, between Zarumilla and Santa Rosa and also between Santa Rosa and Machala. I11 the latter region are

Jan 1, 1923

By V. F. Marsters

Seepages of oil in Ecuador have been known for many years. The locality first to receive attention, and still worked in a modest way, lies on the north shore of the Santa Elena peninsula, between La Puntilla and Salinas. Operations mere first conducted largely by local cdpital. Later, foreign companies acquired large blocks of land, where they have done considerable drilling. For details concerning present drilling activities in Ecuador, we are indebted to Leon Price, an Ame~ican resident engineer of Ecuador. The information solicited came to the author through the office of the American Consulatell with permission to use it. The coastal plain bordering the Province of Tumbes, Peru, continues to the northeast, but narrow on passing the Zarumilla River. From this point northward it widens toward Santa Rosa. In fact, the pampas, as shown on the official Wolf map, correspond fairly well to the areal extent of tbe coastal plain as far as Guayaquil. This is shown in a general way on the accompanying map. The author understands that the Guayaquil enlbayment is bordered on all sides by the coastal plain, as recognized at Tumbes and farther southwest, and that it can be followed without a break as far north as Palmar. This view is supported by the mapped area regarded by Mr. Price as favorable or possible oil territory. Moreover the islands in the Gulf of Guayaquil are the same geologically as the coastal edge, being composed of Tertiary sediments. The author understands also that Tertiary formations occur north of Palmar. According to a report by Mr. Cardon, of Guayaquil, Tertiary sediments are exposed in the region of San Francisco and extend to and beyond Pta. Calera. There is also reason to believe that at least the lower part of the valley of the Santiago River is occupied by Tertiary sediments, ~~hich probably border the const line and extend into the River Mini l)nsin, and into Colombia. On the south coast there are many seepages, most of them near the inner edge of the coastal plain, between Zarumilla and Santa Rosa and also between Santa Rosa and Machala. I11 the latter region are

Jan 1, 1923

By Frank Firmstone

The furnace from which the brick here referred to were taken, was lined under my supervision and blown-in in May, 1902. It was 75 ft. high and 18 ft. in greatest diameter, and used coke to smelt a lean magnetic iron-ore. The lining was put in as follows:—First, blocks 14 in. long by 6 in. thick; second, 2 in. of loam; third, 13.5 in. of 9-in. fire-brick (one-and-ahalf brick wall) laid in English bond; fourth, red brick to within 2 in. of the iron shell; and fifth, 2 in. of slag-wool between the red brick and the shell. The brand of brick used has been known to me for over 20 years, and in my observation had always proved very durable, notably when used in a small furnace 50 k. high which treated the same magnetic. ore. On revisiting and examining the furnace in March, 1903, it was found that the whole of the lining of 14in. blocks at the top, and for an unknown distance (more than 20 ft.) below, had completely disappeared; and a few weeks later the 13.5-in. lining and the red brick at the top likewise vanished, and the furnace was blown out. N~twithstanding the complete failure of the lining higher up, measurements taken after blowing-out showed no unusual wear in the lower part of the furnace. The exact position in the furnace of the piece of brick-work used in the analysis, given below, is not known; but it came from between 30 and 40 ft. above the bottom. It had formed part of the 13.5-in. wall (no 14-in. brick remaining at that level) and consisted of parts of several bricks so firmly sintered together that fracture occurred indifferently through the joints and through the body of the brick. The joints could, however, be traced by a close examination. The surface which had been in contact with the material in the furnace was covered with a yellowish, translucent glaze, somewhat vesicular, and from

Jan 1, 1904

By Ellis Clark

Within the last ten years the progressive party of China, headed by Li Hung Chang, the Viceroy of Chi-Li, has been making great efforts to develop the mining resources of that country, and particularly those that are within reasonable distances of the sea-board. Attention was first paid to the coal-deposits, especially those at KaiPing, which have been placed on a profitable basis with an output of 1500 tons per day, under the energetic management of Mr. Claude Kinder, M.I.C.E., and the successful financiering of Tong King Sing. These coal-mines were described in a report by Kwong Yung Kwang, edited as a paper for the Institute (Duns., xvi., 95.) The attention of the leaders of the progressive party has for the past five years been turned also toward the development of the precious and related metals—gold, silver, copper and lead. De-

Jan 1, 1891

By W. N. Page

Among engineers engaged in mining coal for river transportation, probably no other subject of equal importance has received so little attention as the methods of transferring into barges and other craft. The liability of all our streams to sodden freshets and their attendant drift and ice-gorges, seems to have had little effect upon the design and construction of what are commonly known as rivertipples, beyond the building of breakwaters, and other similar devices, to guard expensive structures from damage. The first method adopted for such transfer was a simple incline, with a movable cradle, which could be raised or lowered to suit the different stages of water. This system, though limited to a small capacity, and to cars not larger than those commonly used underground, possessed two advantages. The first cost was comparatively small; and, since the structure did not obstruct the channel, there was little risk from freshets, the utmost damage from which could be repaired at small expense. Its disadvantages, however, were many, the principal among them being the breakage of the coal by reason of the necessarily high dump; the damage to barges from the same cause; and the difficulties of screening and distributing the different sizes into separate barges. That system has been almost wholly abandoned of late, in favor of the basket-arrangement, lowering vertically into the barge, with the aid of counter-weights, which return the empty basket; while pipes or chutes convey the small coals into other barges, from a complete set of screens, which this method will readily accommodate. As far as my observations have gone, the latter system is now universally employed along all the tributaries of the Ohio. It

Jan 1, 1889

By G. A. Collins

Being much interested in efficiency-work in general, and an ardent reader of writings on this subject by Frederick W. Taylor and others, as applied to manufacturing-plants, and having served my apprenticeship from mucking to the engineering design of ore-dressing and underground plants, I hope that this paper will lead others to investigate the field more fully, to the improvement of general mine- and mill-operations, as well as the advancement, intellectually, physically, and financially, of the employee and his relations with the employer. If a man who is prepared to look closely and observe broadly starts in Canada and zig-zags from camp to camp to southern Mexico, taking time casually to inspect mines, mills, and smelters, he will be pitifully impressed by the great difference in customs, and the general waste of labor, time, and money throughout the country. He will so seldom observe a dollar's worth of results given in exchange for a dollar spent that he will form a poor opinion of operating-efficiency and management. This highly-scientific department, requiring an amount of skill and executive ability equaled in few, if any, of the professions, certainly falls short of the standard established in our greater manufacturing industries. It is easily said that this is due to the diversity of conditions in mining, milling, and smelting. But on second view it must be admitted that there is room for tremendous improvements in nearly every mining-organization. The proposal of such improvements is often met by the argument that any mine is but a temporary affair, yielding such profits as to make efficiency-work of no consequence; but any business which is profitable and worth doing at all is worth doing on a basis which gives the greatest return on the investment.

Jan 1, 1913

By S. Arthur Krom

ThE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction ,of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section of the table. The feed pulp flows gently down this plane and is

Jan 1, 1913

By G. S. Brooks

The tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high tempera tures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3 This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations oil a commercial scale are contributed: I. Physical Properties of Zinc Ferrite. As formed for the most part synthetically by investigators, zinc ferrite exhibits characteristic physical properties, such as octahedral crystals, dark color, and a density over 5, together with a slight magnetic attractability. In examining with the microscope many products of mechanical muffle-roasting kilns, it is, however, impossible to find individual grains which can be identified as consisting entirely of zinc ferrite. The variety of colors, especially where each grain of blende was mechanically free from marcasite, rather conveys the impression of a partial ferritization of the grain. One side or end, for example, may often have the hard, dense surface and dark red to black color of the ferrite, while the balance shows the usual light yellowish brown of a normal iron-free blende.

Jan 1, 1914

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake's waters previous to 1915. Most of this material

Jan 1, 1921