Search Documents

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By E. J. Fasiska, H. Wagenblast

The dilalion of a ivon by interslilial carbon was measured by two independent techniques —dilatometric mesurements at 719 c and X-ray measurments of the urlil cell parameters a1 room temperature after quenching. The relative expansion per increase in cavbon content by both methods is (2.9 + 0.3) x 10-3 pev at. pcl C nrzd is temperature- independent within experimental error. This corresponds to (6.3 5 0.6) cu cm per g-atom for the partial gram-atomic volume of carbon in a iron-only slightly smaller than the atomic volume for iron in the same temperature vange. THE only previous quantitative study of the dilational effect of carbon dissolved in a iron was performed in 1934 by Burns1 which, at the time, generated some discussion of possible sources of experimental error.2 For a system of such widespread importance, we felt that a new investigation was merited. Both X-ray diffraction and dilation measurements were used to determine the expansion of the a iron lattice by dissolved carbon, avoiding as much as possible any previous experimental problems and deficiencies. The dilation method at solution temperature offers not only measurements which are free of residual strain but also, in conjunction with the room-temperature X-ray measurements, a method to detect any large temperature dependence of the partial gram-atomic volume of carbon. To insure that quenching strains did not affect the room-temperature X-ray measurements, wire specimens of constant carbon content but different diameter were examined for such an effect. SPECIMEN PREPARATION The material used for both experimental techniques was "Ferrovac E" iron received in the form of 19-mm-diam rod and stated as having the following impurity contents: C, Cr, Cu, Mn, P, and V, each in the range of 10 to 50 ppm; Co, O, Mo, S, and Si, 60 to 100 ppm; W, 200 ppm; Ni, 230 ppm; N, 4 ppm. The stock material was cold-swaged to 0.71 mm diam for the Debye-Scherrer X-ray camera specimens and portions were cold-rolled from 6.3 mm diam to 0.79- and 0.25-mm sheet for X-ray diffractometer and dilation measurements. The wires were annealed in wet hydrogen for 6 hr at 840°C and 15 hr at 720°C, and then quenched into 0°C water. A chemical analysis for carbon after this treatment gave 0.0046 + 0.0014 at. pct C. Three portions of these wires were subsequently held at 719°C in three different hydrogen + methane mixtures and then quenched, resulting in carbon concentrations of 0.0283, 0.0598, and 0.1067 at. pct C by chemical analysis. After carburizing, the wires were swaged to 0.48 mm and electroplated with silver to prevent carbon loss during subsequent heat treatment. The final heat treatment consisted of holding the wires at 72 1°C for 5 min in a He-2 pct H mixture followed by quenching into 0°C brine. The wires were held at room temperature for a few minutes to remove the silver plating using a phosphoric acid-hydrogen peroxide solution, and then stored in liquid nitrogen until the measurements were made. EXPERIMENTAL TECHNIQUE A) Dilation Measurement. The dilatometer consisted of a gas-atmosphere vertical tube furnace modified so that length changes of a ribbon-shaped specimen could be measured externally. This was done by installing a gas-tight mercury seal at the top of the furnace as shown schematically in Fig. 1. The specimen (21.0 cm long, 1.27 cm wide, and 0.25 mm thick) was suspended in the center of the furnace by 3-mm-diam quartz rods with the upper one passing through the cap of the mercury seal. Above the cap, the upper quartz rod was coupled to a lever exerting a load of about 25 g (-12 lb per sq in.) on the specimen and having a 10 times mechanical magnification. The vertical position of a marker at the other end of the beam was read with a traveling microscope with a precision of 0.01 mm. The temperature gradient of the furnace was meas-

Jan 1, 1968

By M. S. Hunter, D. L. Robinson

An extremely fine subgrain structure found in aluminum and aluminum alloys is shown and a method for revealing this structure is described. The appearance and some of the characteristics of this structure are described and the possible significance of subgrain structure in terms of chemical, electrochemical, and metallurgical processes is considered. GRAINS and grain boundaries, which constitute the principal manifestations of the crystalline aggregates known as metals, play such an important part in determining the characteristics and properties of metals and alloys that their nature and behavior have long been of much concern to the met-allographer. Many investigators have speculated on the possible existence of a finer structure within the usual grain structure and, through X-ray diffraction and metallographic techniques, have revealed evidence that such finer structures exist. Among these structures are the mosaic blocks and domains described by Burgers1 and others in their contributions on crystalline structure and the dislocation theory, the small units associated with polygoniza-tion described by Cahn,2 and the intragranular blocks revealed more recently by Lacombe and Beaujard.3 his paper describes some novel methods for clearly revealing a very fine granular substructure within the usual grains of pure aluminum and aluminum alloys. It also compares the characteristics and behavior of this subgrain structure with those of the ordinary grain structure and gives some examples of the manner in which this substructure may influence the characteristics of aluminum alloys. Metallographic investigations of aluminum and its alloys have dealt extensively with the functions and behavior of grains and grain boundaries and have evolved a definite concept of the relation between grain structure, orientation and physical, mechanical, chemical, and electrochemical behavior. During the examination of etched samples, a roughening or mottling of the body of certain grains has occasionally been observed. Such roughening obviously represented differential attack by the etching solution, but its true significance was not at first realized. It is now known that this roughening probably rep- resented a subgrain structure, although the particular etching treatments used were not capable of revealing this subgrain structure clearly. Also, in practically all cases, the subgrains were apparently far too small to be resolved by the light microscope. Recently, a method has been developed for revealing clearly the subgrain structure of most aluminum alloys. This method is somewhat unique in that it eliminates much of the usual tedious mechanical polishing and the attendant danger of a surface layer of flowed metal and at the same time is simple, rapid, and effective. It involves the use of the Alcoa R5 Bright Dip, a patented chemical polishing treatment licensed by Aluminum Co. of America. This treatment produces a bright, highly polished surface at least the equal of any mechanical polish and also etches the subgrain boundaries as well as the ordinary grain boundaries to reveal both the grain and subgrain structure simultaneously. Metallographic specimens to be examined are taken through the customary grinding and polishing operations used for aluminum alloys.' The usual care required in the final polishing operation to prevent a flowed surface layer and to obtain a high polish is not necessary, however, because any flowed layer is eliminated and a high polish is produced by the final immersion in the Alcoa R5 Bright Dip. Depending on alloy type, this dip takes from a few seconds to about 3 min, after which the sample is rinsed well, blown dry, and is ready for examination. The substructure can be revealed by some of the usual metallographic methods such as electropolish-ing or mechanical polishing and etching but no method has been found which is the equal of the new chemical polishing treatment. Mechanical polishing followed by the usual metallographic etching is not entirely satisfactory for revealing this substructure, probably because of the flowed surface layer resulting from the mechanical polish. If the usual etching methods are prolonged sufficiently to remove this layer, the specimen surface becomes quite rough and the substructure is not defined clearly.

Jan 1, 1954

By H. C. Vacher, C. J. Newton

EXTENSIVE investigations in the field of residual strain measurement by X-ray diffraction have been made by Bollenrath, Hauk, and Osswald,1 by Smith and Wood,2'3 by Greenough; by Rosenthal and Norton." and many others. Since X-ray strain measuremeits apply only to those crystals of the test body which are of the proper condition and orientation to diffract and since the residual strains revealed may be accompanied by either body or tex-tural stresses, there has been considerable disagreement among investigators with respect to the validity of conclusions in this field. Although the experi-mentors have employed a variety of loading schemes, surface preparations, and X-ray wave lengths, the observations almost invariably have been made only on the outer surfaces of the specimens. The present note is not to be construed as an exposition of a new method of stress analysis by X-ray strain measurements on sections but as a presentation of some results which point to interesting possibilities for further experiments with sections. The two test rods used in this study were of ingot iron annealed at 910°C. The initial length of the gage section was 2 in. and the diameter was 0.415 in. Cross-sections were cut from the ends of the annealed rods to provide strain-free material. The tensile rod was axially loaded the desired amount in a commercial testing machine. A 1 in. portion of the gage length was cut from the other rod and was subjected to compression in the same machine. Details of this plastic straining of each rod are given in the upper half of Table I. A half-cylinder piece about 1/4 in. long was obtained by making a short longitudinal plane cut containing the axis of the rod near the center of the gage length. From adjacent material a disk about 1/8 in. thick was cut to provide the cross-section specimen. Later another section was cut from this same region with an angle of 30" between the normal to its surface and the axis of the test rod. A cross-section and a longitudinal section were cut from the compression rod in a similar manner. All of these as well as the strain-free cross-sections were mounted in Bakelite and used as specimens for the following X-ray strain measurements. During the course of the study, it became apparent that the condition of the surface of a specimen was a highly critical factor. One of the annealed strain-free specimens as a control was subjected to about 24 hr of polishing with fine alumina, interrupted about every 2 hr for etching with 1 pct nital. Its lattice parameter was determined at intervals from measurements on back-reflection X-ray diffraction patterns, which were calibrated with diffraction from tungsten powder. The parameter gradually approached the value found in the literature for strain-free iron and remained there, within the limits of the experimental error. This determined a long polishing and etching procedure which was adopted for all the specimens and which gave X-ray results from the surfaces believed to be representative of each specimen as a whole. A large number of back-reflection patterns were made with cobalt and chromium radiation, all at normal incidence. Except for some preliminary stationary exposures made to monitor the removal of cold work from the surfaces, each exposure was made with the specimen slowly translating and the film slowly rotating. In appropriate cases a thin layer of a standard metal powder, tungsten with cobalt radiation and silver with chromium, was dusted over a film of vaseline on the surface of the specimen to serve to calibrate the X-ray patterns. After the preliminary work, four films were made,

Jan 1, 1956

By J. Chipman, J. B. Gero, T. B. Winkler

D. C. Hilty—This paper is a useful and timely addition to our store of quantitative data relating to manganese distribution between slag and metal in steel-making processes. For some time, many of us have suspected that the values of Kmn derived by Körber and Oelsen might be too low, and this paper now appears to confirm that suspicion. Application of the new constant to openhearth data should prove interesting. The manganese deoxidation curves of fig. 4 agree fairly well with direct measurements of isothermal solubilities of oxygen in liquid iron containing manganese that have recently been made at the Union Carbide and Carbon Research Labs., Inc. According to the solubility data just mentioned, however, the curves for 1550" and 1600°C lie much closer to each other than the authors have indicated. In other words, the solubility measurements suggest that the logarithm of the oxygen solubility is not a linear function of the reciprocal of the absolute temperature, as the authors have assumed for their calculations. It seems possible that this discrepancy may be due in part to the authors' use of the distribution coefficient, L,,, obtained from Taylor and Chipman's curve for the solubility of oxygen in iron as shown in fig. 2. Taylor and Chipman gave the equation of this curve as —6320 Log % 0 - ---T + 2.734 Their data, however, can be fitted equally well by a curve having the equation: 13.23 x104 1.18x10" Log % O = 36.350 -13.23x10 Moreover, this curve also fits the authors' oxygen distribution data somewhat better than does the linear curve of Taylor and Chipman. Its use in the derivation of Lo for calculation of the deoxidation curves by the authors' eq 15 causes the effect of temperature on the calculated curves of fig. 4 to agree quite well with the temperature effect that has been observed. An experimental determination of the temperature coefficient of the manganese reaction appears to be desirable. J. E. Stukel—Because the authors have done such an excellent job, my comments will be confined to additional information. Very shortly Professor T. L. Joseph and I will publish the results of a study of the reaction between molten manganese and silica. It was found that electrolytic manganese, melted in silica crucibles, reacted with the silica to form a silico-manganese alloy containing 18 pct silicon (1500°C) and a silica saturated MnO-SiO, slag. Therefore, the presence of silicon and its oxides in the Fe-Mn-0 system will affect the equilibrium. Carbon is also an important factor. The higher the carbon content of the iron the less ability manganese has to reduce silica. As a matter of interest, recently a study of the manganese equilibrium in carbon saturated iron and blast furnace slags was completed at Carnegie Institute of Technology. As a comparison to the present study, 2 to 5 hr were required to reach equilibrium and temperature was a much more important factor than slag composition in determining the (Mn)/(MnO) ratio. These results will also be published in the near future. It can be seen, therefore, that the results of this paper cannot be applied directly to openhearth studies without a degree of flexibility. J. Chipman (authors' reply)—With regard to the effect of silicon on the manganese constant, this effect is, of course, known. Much more data is needed in order to establish it accurately, and I hope we can look forward to having some accurate data on that. Mr. Hilty suggests that a three-term expression for the Taylor-Chipman solubility of oxygen in liquid iron might fit a little better than the two-term equation. I think that it would be too great a compliment to the precision of the data to employ a three-term equation, and I would still recommend the simple, two-term expression.

Jan 1, 1951

By Fredrick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By Larry Kaufman

A useful method for estimating the entropy of NaCl type compounds has been developed by combining the Debye theory of specific heat with the Lindemann formula. This method pemnits calculation of the entropy from a knowledge of the atomic weight, atomic volume, and melting point of the compound. Comparison of the calculated and observed entropies of 35 NaCl type compounds over a wide temperature range yields good agreement thus establishing the usefulness of the method. Application of the method to other crystal types is also discussed. KUBASCHEWSKI~ has suggested a useful method of estimating the enthalpy of formation of inter-metallic compounds from a knowledge of the crystal structure, lattice parameter, and heats of sublimation of the component elements. This method is quite valuable in predicting the tendency for compound formation in a given system and is of particular value in considering systems for which no experimental data are available. In order to supplement the enthalpy calculation afforded by Kubschewski's method, it would be of value to be able to estimate the entropy of compounds so that the entropy and free energy of formation could be evaluated. Although a considerable body of such data determined by calorimetric and equilibration techniques exists at present, the difficulty of making such measurements (particularly at high temperatures) and the ever increasing number of new compounds which are of interest make the desirability of such a computational method clear. This paper deals with a method for calculating the entropy of a compound from a knowledge of the atomic weight, atomic volume, and melting point. Since these data are generally easier to determine and therefore more readily available than thermo-dynamic data, they should provide an additional tool in estimating the stability and reactivity of compounds at high temperatures. I) THE ENTROPY OF PURE METALS As a first approximation, the specific heat of a pure metal can be represented by a sum of terms where C,($/tI is the vibrational specific heat calculated on the basis of the Debye theory, lo4 TC, (0/T) is an approximation to the Cp - C, correction. T is the electronic specific heat, and Cp (p) is the magnetic specific heat. Although the Debye theory does not provide a complete description of the vibrational specific heat, i.e., the Debye temperature 0 is not a constant, it does provide a good approximation when used properly. Blackman6'7 has written several reviews on this subject discussing the different values of 0 determined by various methods (specific heat, X-rays, elastic constants, electrical resistivity, and so forth), as well as the observed temperature dependence of 0 with T. In the present case the 0 in Eq. [I] naturally refers to the specific heat 0. The variation of Debye 0 (as determined from specific heat measurements) with temperature is observed to exhibit its most radical behavior at very low temperatures. At higher temperatures the 8 values are observed to become more nearly constant. Blackman6'7 has presented the variation of 0 with temperature for several metals. His tabulation is reproduced in Table I. Reference to Table I shows that above a certain temperature level, 0 remains fairly constant. The value of 0 which is most useful in computing the specific heat, and hence the entropy, is the value of 0 in the range 0/6 « T « 0. In 1910, Lindemann' suggested a relation for estimating Debye 0 values. According to this formula, where V is the atomic volume, T is the melting point in 'K, M is the atomic weight, and CL is a constant. Mott and Jones9 present this formula and state that there is at present no satisfactory theoretical explanation, but that it does have an empirical basis. By using the valuesof 0 in Table I along with known1' values of M, T, and the molar volume VM, where the Lindemann constant can be evaluated. This

Jan 1, 1962

By Albert Brown, Emil R. Ermert, Fredrick C. Pearson

EARLY in 1946 the Shen-Penn Production CO., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenan-doah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,-000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1—An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2—Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3—Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1953

By E. B. Burwell, R. H. Nesbitt

Designed by army engineers, the NX borehole camera provides the most economical method of subsurface exploration so far devised. Continuous cylindrical color photographs now reveal minor flaws in foundation bedrock not always disclosed by borehole samples. A unique projector transforms the photographs into true-to-scale images of three dimensions. ANEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery. The pilot model of the camera has more than paid for itself as a result of its success in bringing to the surface at two dams information previously obtainable only by costly drilling of mansized boreholes for subsurface on-the-spot examination. Such bores cost as much as $200 per lineal foot as against $10 per ft for the conventional 3-in. or NX exploratory core borings from which the present invention derives its name. The NX camera can now photograph completely the interior surface of these borings. Research and development for the first camera and projection equipment were conducted by Engineering Research Associates, Division of Remington Rand, Inc., under the technical supervision of the Geology and Geophysics Branch, Office of the Chief of Army Engineers in Washington, in accordance with plans and specifications furnished by this branch. Subsequent modifications of the camera-lowering device, transporting equipment, and special field tools were made in the Corps of Engineers' Ohio River Division Laboratories in Cincinnati. The background of this development is interesting. Among the more difficult foundation problems involved in construction of concrete dams are those resulting from bedrock imperfections that escape disclosure by conventional exploration methods. Often these imperfections are of sufficient magnitude to introduce costly changes, especially when their presence is discovered only after foundation excavation is well in progress. Bedrock flaws most frequently camouflaged may be ruptures resulting from the enormous stresses to which rocks have been subjected, or they may be planes or zones of weakness related to chemical alteration and underground erosion. Obviously, detailed information on their location, dimensions, and structure is important, as these factors can affect the stability of a dam and the security of life and property downstream. Their discovery and appraisal entail extensive subsurface exploration. At present the most economical exploratory tool available to geologists and engineers is the small-diameter diamond core drill by means of which cores of the foundation bedrock are recovered for examination and testing. All too often, however, these samples fail to disclose minor foundation flaws that may be of major importance before a structure is completed. As a result, the small-diameter drillings are supplemented generally by more reliable but much more costly shafts, tunnels, or large-diameter calyx drill holes that permit the investigator to examine the foundation rocks in place. It was to reduce the number and cost of these expensive and time-consuming investigations, as well as to obtain more complete information on rock structure from the smaller borings, that the NX borehole camera was developed. That it has been eminently satisfactory in accomplishing that purpose is demonstrated by its success most recently at the Folsom dam, under construction on the American River, 23

Jan 1, 1955

By Frederick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production Co., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenandoah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1-An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2-Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3-Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1952

By B. R. Berger

The Getchell area in the northern Osgood Range, Humboldt County, Nevada, was first prospected in the late 1800s for silver, copper, and gold; the first recorded mention of mining activity concerned a silver discovery. The September 17, 1874 edition of the Winnemucca Silver State notes that the Crystal Mining District was newly organized in the Fremont Range (as the Osgood Range was then called) to include discoveries of silver, lead, and antimony made on the Louisa claim. The name Crystal was derived from the plentiful quartz crystals found in-cavities near the prospects. This same area, occurring on the northwestern margin of the Osgood granodiorite stock, was later mined as the Richmond tungsten property, and crystals may still be found there in cavities in a massive garnet tactite. By 1878, how-ever, the name Crystal had been abandoned in favor of Potosi. The next flurry of activity in the Osgood Range was reported in 1899 when a copper strike on Granite Creek in the southern portion of the range received attention. The copper occukences were in a granite contact zone on the southeastern edge of the Osgood stock and, in 1916, the first tungsten in the district was discovered in the same deposit. During the last part of the nineteenth century, cattle and sheep were brought into the Kelly Creek Valley east of the Osgood Mountains by various ranchers. Alphonso and Adrian Bernard were among these ranchers, and in the first decade of the twentieth century, one of them recognized the altered rock where the Getchell Center it is now located. A 3-m (10-ft) deep prospect pit was dug on the outcrop, but the highest assay ran about $11/t ($10 per st). No further work was done on the gold-bearing rock. In 1934, Emmet Chase of Battle Mountain and Ed Knight of Golconda prospected in the area of the Bernard prospect pit and located several lode claims. At this time, Noble H. Getchell, a state senator, was looking for new mining opportunities to develop. He held interests in the Gold Circle Consolidated at Midas, which was becoming a losing venture. Chase and Knight brought their discovery to his attention, and he grubstaked them to prospect further in the area. In need of financial backing, Getchell solicited the help of George Wingfield, Sr., who held a minor interest in the Gold Circle. Wingfield was a successful banker and mine operator during the heyday of Tonopah and Goldfield, and he had become good friends with Henry C. Frick and Bernard Baruch. Wingfield let Baruch in on several very successful mining ventures in Goldfield, and Baruch returned the favor by underwriting the financing of the Getchell mine. Eleanor Roosevelt and Jack Dempsey were early stockholders in the Getchell operation. George Wingfield brought his brother-in-law, Roy A. Hardy, a consulting engineer who had constructed the American Flat mill near Virginia City, to look at the property. Upon inspecting the Chase-Knight claims, Hardy declared the whole area to be mineralized. A crosscut was driven to check the extent of the ore, and the results were better than anticipated. The locators were reportedly given $50,000 for the claims. The Getchell Mine, Inc., was organized on November 5, 1936. A small railroad that ran from Battle Mountain to Austin was purchased, and the ties and rails were moved to Getchell to be used in underground exploration. Enough reserves were found in the Center and South pit areas to construct a 40 t/d (44 stpd) mill. The financial and engineering help for the mill was provided by the Newmont Mining Co. for a 17 1/2% interest in the corporation. Newmont set about trying to solve the metallurgical problems with the sulfide ore, and also directed the early development work. Newmont wanted to grind the sulfide ore underground and oxidize it in the atmosphere by spreading salt on it. Detrital Flat in Arizona was purchased to provide salt for

Jan 1, 1985

By Robert K. Waits

The resistivity, temperature coefficient of resistance, stability at 200°C, and structure of annealed Si-Cr films have been studied as a function of film cowposition. Colorimetric analyses of the films indicated 20 to 60 wt pct Cr over the resistivity range of 1 to 10-4 ohm-cm. Resistors were delinealed by photolithographic etching, contacted with aluminum, and mounted in TO-5 packages. The average temperature coefjicient of resistance, a, between 50" and 150°C is related empirically to the film resistivity, p, by a (ppm per °C) = -2900 - 1140 log p (ohm-cm). Near a resistivity of 3.5 x 10-3 ohm-ctn (30 at. pct Cr) , the temperature coefficient changes from positive to negative. The temperature at which the resistance maximum occurs increases with decreasing resistivity. The conduction mechanism between —196" and +360 C appears to have two components—an activated conduction dominating a1 lord chromium content and higher temperatures and a linearly temperature-dependent conduction dominating at high chromium content and low temperatures. Electron diffraction patterns showed the films to consist of Cr3Si and amorphous silicon. Resistors thicker than 150A typically drifted less than 0.6 pct after 5000 hr stor-age at 200°C. Resistors as thin as approxinzately 80°A that had a silicon overlayer showed similar stability. Such films had sheet resistivities of 10 kilohm per square and temperature coefficients near —600 ppm per "c. THIN-FILM resistors having sheet resistivities greater than 1 kilohm per square are required in many integrated circuit applications. A process for producing such resistors should be compatible with present circuit fabrication and packaging, including exposure to maximum temperatures of 300° to 570°C during contact alloying, die-attach, and ceramic package sealing. In addition, the resistors should have a low temperature coefficient of resistance and change less than 1 pct during storage at temperatures up to 200°C for 1000 hr or longer. Reports of work beginning in 1949 at Battelle Memorial Institute indicated that, among other materials, the silicides of chromium, Cr-Co, molybdenum, tantalum, and tungsten were worthy of further study as high-stability resistive films. Later work on Si-Cr films vacuum-deposited by flash evaporation from a tungsten boat1 led to the conclusion that Si-Cr had "excellent properties for development into high- stability ... resistive elements". More recently, Si-Cr films have been vacuum-deposited from a tantalum boat,2 from a BeO-coated tantalum boat,3 by flash evaporation from an electron-beam-heated tungsten Source,4 and by triode sputtering.5 This paper describes a study of Si-Cr films vacuum-deposited by electron-beam heating of Si-Cr alloys. Resistivity, temperature coefficient of resistance, stability at 200°C, and structure were studied as a function of film composition. EXPERIMENTAL PROCEDURE Film Deposition. Si-Cr sources were prepared by vacuum-melting pressed pellets of mixtures of powdered chromium (99.9 pct, -100 mesh, Lunex Co., Pleasant Valley, Iowa) and silicon (99.99 pct, -325 mesh, United Mineral and Chemical Co., New York). A permanent-magnet focused electron-beam gun having a water-cooled copper crucible was used to heat the pellet until complete melting occurred. The mixture was then kept molten for an additional 5 min. The alloy thus formed was used as the source material for Si-Cr film depositions using the same electron-beam gun. Pieces of semiconductor-grade silicon ingots were used as sources for silicon depositions. The films were deposited within a standard vacuum evaporator having an 18-in.-diam Pyrex bell jar, a liquid-nitrogen-cooled trap, and a Consolidated Vacuum Corp. 6-in. diffusion pump containing Dow Corning DC-705 pump fluid. The substrates were thermally oxidized* silicon wafers 2 to 2.5 cm in diam. The

Jan 1, 1969

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.' This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

By M. A. Dayananda, R. E. Grace

Vapor-solid diffusion couples were employed in a study of ternary diffusion in the single-phase copper-rich corner of the Cu-Zn-Mn system Interdiffusion coefficients were measured at three different compositions corresponding to the intersections of diffusion paths determined at 850°C. Intrinsic diffusion coefficients were determined at two compositions by the Philibert-Guy method. New relations between the various intrinsic diffusion coefficients are also presented. MOST of the investigations of ternary diffusion have been made with "sandwich" couples formed by welding together two homogeneous solid solutions with or without markers placed at the interface. With such couples Kirkaldy and his coworkers1,2 have determined interdiffusion coefficients which describe ternary diffusion in the substitutional alloy systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy3 have reported intrinsic diffusion coefficients for Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.4 The use of semi-infinite diffusion couples, for example, vapor-solid couples, where the diffusing species are supplied from a vapor source in contact with a diffusion disk, has so far been confined to studies of binary diffusion. Balluffi et a1.5,6 have successfully determined the interdiffusion as well as the intrinsic diffusion coefficients in several binary metallic systems employing vapor-solid couples with markers initially placed at the vapor-solid interface. They have also discussed the general advantages and limitations of such couples. Vapor-solid diffusion couples can successfully be employed in ternary diffusion studies. The importance of such couples in ternary diffusion lies in the fact that inert markers lie close to the vapor-solid interface, and the composition of the marker plane is virtually known before experimentation begins. Another minor advantage is that the method of Philibert and Guy4 may be used with three alloys instead of four. Lastly, the diffusion paths need not be S-shaped, as pointed out by Meijering7 for "sandwich" couples. The Cu-Zn-Mn system is convenient for ternary diffusion studies because of the large single-phase field in the copper-rich corner. The vapor pressure of zinc above such alloys is known, and X-ray measurements indicate that the molar volume is nearly constant over a wide range of compositions.8,9 It is the purpose of this paper a) to extend the analysis of Balluffi and seigle5 to permit an evaluation of interdiffusion coefficients in ternary vapor-solid couples, b) to use the method of Philibert and Guy to determine intrinsic diffusion coefficients with such couples, and c) to present experimental data on both interdiffusion and intrinsic diffusion coefficients for the Cu-Zn-Mn system at 850°C. INTERDIFFUSION IN TERNARY VAPOR-SOLID COUPLES The analysis of Balluffi and seigle5 is extended in this section to a vapor-solid couple where two solutes diffuse from a vapor source into a ternary solid solution. To take into account the expansion of the diffusion disk caused by the absorption of mass from the vapor phase, the total fluxes are expressed on the basis of a coordinate system that moves with the velocity of the vapor-solid interface; thus. where D3ij are the intrinsic diffusion coefficients,4 v(x, t) is the local Kirkendall velocity of mass flow, and F(t) is the negative velocity of the vapor-solid interface (x = 0). Both these velocities are based on a fixed coordinate system far removed from the diffusion zone. Using the continuity relations and Darken's method1' for a ternary system in which components 1 and 2 diffuse from the vapor phase into a solid of negligible vapor pressure, one obtains

Jan 1, 1965

By B. E. Eakin, R. T. Ellington

An apparatus and a procedure for determining the viscosity behavior of hydrocarbons at pressures up to 10,000 psia and temperatures between 77 and 400° F are described. The equipment is suitable for measuring viscosity of either the liquid or vapor phases or the fluid above the two-phase envelope for systems exhihiting retrograde phenomena, according no the phase state of the system within these ranges of temperature and pressure. Equations are developed for calculation of viscosity from the experimental measurements, and new data for the viscosities of ethane and propane at 77° F are reported. INTRODUCTION With the advent of higher pressures and temperatures in industrial processes and deep petroleum and natural gas reservoirs, demand has increased for accurate values of physical properties of hydrocarbons under these conditions. Proportionately, more frequent occurrence of natural gas and condensate-type fluids is encountered as fluid hydrocarbons are discovered at greater depths. This increases the importance, to the reservoir engineer, of being able to predict accurately the physical properties of light hydrocarbon systems in the dense-gas and light-liquid phase states. Reliable gas viscosity data are limited primarily to measurements made on pure components near ambient temperature and at low pressures. Few investigations have been reported for high pressures, and except for methane, data on light hydrocarbons are subject to question. This is demonstrated by the large discrepancy between sets of data on the same component reported by different investigators. For mixtures in the dense gas and light liquid regions and for fluids exhibiting retrograde behavior there are very few published experimental data. Viscosity data for methane have been reported by Bicher and Katz,1 Sage and Lacey,12 Comings, et al,3 Golubev,3 and Carr,3 with good agreement among the last three sets of data. Comings, Golubev and Carr utilized capillary tube instruments for which the theory of fluid flow is well established. The theory permits calculation of the viscosity directly from the experi- mental data and dimensions of the instrument alone. Sage and Lacey, and Bicher and Katz used rolling-ball viscometers. The theory of the rolling-ball viscometer has not been completely established, and these instruments presently require calibration by use of fluids of known viscosity behavior before viscosities of test fluids can be measured. To obtain accurate data it is necessary that the rolling-ball viscometers be calibrated by use of fluids of density and viscosity similar to the test fluids, a difficult selection for the gas phase. From the methane data and experimental tests on various natural gases, Carr developed a correlation for predicting the PVT behavior of light natural gases.2,3,4 This correlation was based on data for a very limited composition range; its application to rich gases and condensate fluids is questionable. The object of this investigation is to develop an instrument which can be used to obtain viscosity data at reservoir temperatures and pressures, for rich gases, condensate-type systems above the two-phase envelope and light liquid mixtures. These data will be used in an effort to develop correlations to represent the viscosity behavior of these fluids. APPARATUS In a previous viscosity study Carr2 utilized a modified Rankine capillary viscometer configuration," Fig. 1. In this instrument the gas to be tested is forced through the capillary tube in laminar flow by motion of a mercury pellet in the fall tube, the measured displacement time being that required for the mercury slug to move between the brass timer rings. The viscometer is constructed of glass and mounted in a steel pressure vessel. The test gas pressure in the viscometer is balanced by an inert gas (usually nitrogen) in the vessel. Excellent results have been obtained with instruments of this type, with Carr2 and Comings5 reporting repro-ducibilities of 99.5 to 99.3 per cent and an estimated absolute accuracy of 99 per cent. However, these instruments have limitations which have precluded their use for liquids. The need for maintaining a balance between pressures of the test fluid and inert gas in the viscometer vessel presents operating problems, and requires charging the test fluid to the viscometer very slowly. The principle drawback to the Rankine unit is behavior of the mercury slug which provides the pressure differential across the capillary. When even trace quantities of propane or heavier hydrocarbons are present in the test gas, the mercury tends to subdivide

By H. P. Leighly, F. C. Perkins

THERE have been several statements in the literature about the difficulty of producing single crystals of high-purity (99.99pct) by the strain-anneal method. Consequently, investigators tend to employ low-purity aluminum for their single-crystal experiments, or else resort to the Bridgman or other techniques which depend on solidification for the production of single crystals. The following paragraphs describe a solid-state method for the manufacture of single crystals of high-purity aluminum which should provide crystals with greater perfection than those formed by solidification. The starting material for this method of producing single crystals was secured from the Aluminum Corp. of America and has a purity of 99.99 pct, the balance being trace amounts of impurities. Specimens approximately 1 by 4 in. are sheared from sheet having a nominal 0.050 in. thickness. The specimens are given a preliminary anneal at 640°C for approximately 3 hr in order to remove fabrication strains and to produce an average grain size of about 1/4-in. diam. The specimens are then etched in Tucker's etchant (45 pct HC1, 15 pct HNO3, 15 pct HF and 25 pct H2O) to remove the oxide film. Critical strain is applied by wrapping each specimen about a 1 3/4 in. round and subsequently straightening it against a flat surface. The high-purity aluminum sheet is sufficiently soft that this operation can be accomplished by ordinary finger pressure. The specimens are immediately annealed again at 640°C for 3 hr and reetched for examination. Ordinarily, considerable growth of certain of the grains will have occurred, and occasionally a single crystal will be produced on the first attempt. The procedure of alternately straining, annealing and etching is repeated until the majority of a batch of specimens contains usable crystal sizes. Typical examples are illustrated in Fig. 1. The greatest changes in crystal sizes are produced in the initial treatments. As the average crystal sizes get coarser in the later treatments, the sever- ity of the strain must be increased in order to produce grain boundary- migration. This increase in severity is effected by decreasing the diameter of the round used for straining (to 1 1/2 in., for example) and/or wrapping the specimens about the round twice, with opposite faces in contact with the round, before flattening. Usually the strain treatments described are not severe enough to produce nucleation in coarse grain high-purity aluminum. The growth of grains occurs by strain-induced grain-boundary migration. It has been observed that the grain boundaries move most readily during the first hour or so of each annealing treatment and that the rate of movement decreases with extended holding times at temperature. Prolonged annealing treatments are therefore not usually beneficial. Similarly, the rate of growth of each crystal appears to depend upon the orientation of the crystal with relation to those of its neighbors. Frequently island grains are formed after the initial heat treatment as the result of slow grain-boundary migration. These sometime become stationary during later heat treatments. Twin orientation interfaces are frequently developed during annealing. These imperfections can usually be removed by increasing the severity of strain to produce actual nucleation of new grains of more favorable orientation at the imperfection interfaces. The largest single crystals produced in our laboratory by the above method measured 4 by 1 by 0.050 in. Examination of Laue back-reflection patterns from a limited area of the specimens, gave no evidence of polygonization. Probably there is some indication of polygonization in the original grain area provided a more sensitive technique is used for detection. Experiments to produce wider specimens were less successful, possibly because wider sheets increase the complexity of the strains induced by deformation and promote widespread nucleation. Grain boundary migration occurs preferentially in a direction parallel to the longitudinal axis of the specimen. The choice of specimen geometry with respect to the rolling direction of the sheet appears to be immaterial in regard to the production of single crystals.

Jan 1, 1961

By J. Washburn, R. Drouard, E. R. Parker

Temperature dependence of the rate of recovery in zinc single crystals after a simple shear deformation at low temperature was investigated. Some tentative suggestions regarding the annealed and strain-hardened states of a crystal are discussed. RECOVERY may be defined as the gradual return of the mechanical and physical properties of strain-hardened metal to those characteristic of the annealed material; an increase in temperature increases the rate of recovery. The annealing process in strain-hardened polycrystalline metals is complicated by the inhomogeneity of strain which always exists in aggregates. Polygonization in bent regions of the crystals and growth of new almost strain-free grains starting at points of severe local distortion1-:' make it almost impossible to isolate and study the recovery process. Homogeneously strained single crystals, however, do not polygonize or re-crystallize and hence they can be used advantageously to study recovery. In such crystals strain hardening is completely removed by recovery alone. Since recovery is a process whereby certain lattice disturbances introduced by plastic flow are gradually reduced, a knowledge of the rate and temperature dependence of this process for various conditions of prestrain might be helpful in formulating a model of the strain-hardened state. For simplicity it seemed desirable to limit the type of prestrain to the simplest obtainable, i.e., simple shear strain. In the experiments to be described, recovery was studied by observing changes in the stress-strain curve of prestrained zinc single crystals held for various times at temperatures above that employed for straining. Single crystals were grown from the melt by a modified Bridgeman technique from Horse Head Special zinc 99.99 pct pure, and from spectrographically pure zinc 99.999 pct pure. They were grown as 1 in. diameter spheres and acid-machined' to the final specimen contour. The test section was a cylinder about 1/8 in. high and 3/4 in. in diameter. The conical sections adjacent to the test section were cemented into the grips so the load could be transmitted to the crystal as uniformly as possible. The specimens were oriented so that in testing the maximum shear stress was applied along one of the slip directions, [2110], in the (0001) plane. Details of the production and testing of such specimens have been presented.' Each test was carried out according to the following schedule: 1—The crystal was strained at — 50°C until it reached a maximum shear stress, ,,,. The strain rate was approximately 5 pct per min in all cases. 2—After straining, the crystal was unloaded before the temperature was changed. Unloading required about 3 min. 3—The temperature of the specimen was then increased from — 50°C to the temperature, T, of recovery. This change in temperature was completed in a time of less than 2 min. The specimen remained at temperature, T, for a time, t, which differed for the various specimens. 4—Thereafter the temperature was again reduced to — 50 °C in approximately 3 min. 5—While at —50°C, the stress-strain curve after recovery was obtained. 6—The specimen was then unloaded and annealed for 1 hr at 375 °C in a helium atmosphere to bring about complete recovery. Cooling to room temperature after anneal required 90 min. 7—The same crystal could be re-used for another test because the plastic properties after annealing closely duplicated those of the original crystal. The specimen was immersed during the test in a bath of methyl alcohol which, through a system of tubes, could be pumped through either of two heat exchangers to regulate the temperature; this was accomplished by circulating the liquid through coils immersed in a bath of acetone and dry ice for cooling or in a bath of warm water for heating. Test temperatures were thus maintained constant within ±1°C. The — 50°C temperature was low enough so that no measurable recovery occurred during unloading and reloading. The stress-strain curve continued after recovery along a path below, but approximately parallel to, the path of a curve obtained in an uninterrupted test. Fig. 1 shows some of the results from a specimen of 99.999 pct Zn. The amount of downward displacement of the curve due to recovery was a

Jan 1, 1954

By Wilbur Jurden

THE writer's first experience with a nonferrous reduction plant of great magnitude was at the Washoe reduction works of Anaconda some 35 years ago. Here was a plant which had been planned with remarkable skill and foresight considering the time and the state of development of copper-plant practice in the year 1902. The designer utilized topography to fullest extent to provide proper sequence of operations and, what is most remarkable, to leave adequate space for future developments, most of which at that time were unknown. However, the practice then was to locate the various units of the reduction works at the most advantageous points of the existing terrain with little regard for tramming or other auxiliaries and then connect these various units by the essential trackage, conveyor systems, piping, etc., as the need developed. This occasionally led to undesirable track arrangements, sharp curves, and steep grades, especially when it became necessary to extend various portions of the plant. Conveyor systems also became rather complicated, running as they did at various angles, and such items as piping and electrical distribution were often found to be in the wrong place, entirely inadequate in size, or awkwardly arranged for any kind of extension. This condition was not peculiar to Anaconda, for all copper plants at that time were built in the same manner and it was the constant association with these difficulties which, in the year 1925, influenced the layout of the Andes Copper Mining Co. plant. In that plant all trackage was laid out straight and level, all conveyors at right angles to each other with minimum length and number of transfers. All buildings were placed parallel and the main structures were complete for all purposes so that auxiliary buildings and dog houses would not be added later. Piping and electrical work was provided for in the original layout and carefully designed to avoid additions and alterations, and careful study given to every movement of material throughout the entire plant so that it would be accomplished with the least possible effort. Naturally it was hardly expected to attain all these objectives perfectly but our efforts did succeed in creating a plant which was unique and outstanding for its time-1927. It was also most gratifying to find that these design principles contributed to considerable savings starting right in the drafting room, carrying through the construction and ultimately yielding savings in operations and manpower. Not only that, but such a plant gives the observer an impression of symmetry and order, is more attractive to the workmen, and unquestionably eliminates many accident hazards. However, the Andes plant buildings were fitted to the existing terrain instead of having terrain created to fit the buildings-an item which we found advantageous to correct on the next large plant. At Morenci in 1939, all of the desirable features of the Andes plant such as parallel buildings, etc., were incorporated; but we went one step further-power shovels were brought in to make the terrain fit the reduction works. The result at Morenci is well-known and needs no elaboration here, but the success achieved by the design methods used for this and previous plants naturally influenced and guided the layout of the Chuquicamata sulphide plant which is the largest yet conceived. Chuquicamata Plant Design At Chuquicamata several factors not encountered previously complicated the problem to a great extent. The most desirable location for the smelter would allow smelter gases to blow directly into the open-pit mine already producing 60,000 tons of oxide ore per day and employing 1550 men. This, of course, would be a serious condition and, therefore, we were forced to move the smelter to a less desirable location but followed our previous experience at Morenci and made the terrain fit the job. The most difficult problem, however, was the provision for receiving various types of ore both by rail and conveyor. These consisted of: 1-Sulphide-bearing residue from the stockpile from which oxide copper had previously been leached. 2-Sulphide-bearing residue coming direct from the leaching vats. 3-Sulphide ore crushed at the existing crushing plants and hauled to the concentrator in cars. 4-Sulphide ore from the new crushing plant adjacent to the concentrator. 5-Sulphide ore obtained

Jan 1, 1952

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962

By O. N. Carlson, H. A. Wilhelm, J. M. Dickinson

On the basis of microscopic studies, melting-point observations, and X-ray analyses, a phase diagram is proposed for the Cb-V system. A complete series of solid solutions is formed with a minimum in the solidus at 1810°C near 35 wt pct Cb. No compounds or intermediate phases were found in the system above 650°C. THERE is an ever increasing need for better structural metals and alloys for use in nuclear reactors. In addition to the normal properties of engineering structural materials, such as high temperature strength, resistance to corrosion, and fabric-abil~ty, the nuclear properties of the material must be considered. In a nuclear reactor it is important to conserve neutrons, so a material which removes these neutrons from the reaction excessively is considered to have unfavorable nuclear properties. In nuclear-reactor design the engineer must have nuclear as well as other data available on alloys in order to make a wise selection of materials. Due to the fact that many of the common structural materials have undesirable nuclear properties, it is vital that new alloys of metals having more favorable nuclear properties be investigated. Columbium and vanadium are both high melting metals, both exhibit resistance to chemical attack, and no great difficulty is encountered in fabricating them into desired shapes. With proper treatment both metals can be cold rolled extensively without failure. In addition they have desirable nuclear properties for certain types of reactors. Therefore, the alloys of columbium and vanadium should be of interest in the atomic energy program. Since an alloy-development program is enhanced by a knowledge of the phase equilibria of the components, this investigation was undertaken to establish the phase diagram for the Cb-V system. According to the Hume-Rothery rules for alloying,' the chemical similarity, crystal structure, and atomic-size factor are favorable for a complete series of solid solutions for this system. Both elements are in the same family of group V of the periodic table and thus are quite similar chemically. The crystal structures of columbium and vanadium are compatible for extensive solid solubility, since both have body-centered-cubic structures. The atomic diameters of columbium and vanadium are 2.85 and 2.62Å, respectively. This difference of slightly more than 8 pct is well within the 15 pct maximum difference allowed for extensive solid solubility. Experimental Procedures Source of Materials: Columbium powder and sheet trimmings were obtained from the Fansteel Metallurgical Corp. According to the manufacturer the metal contains less than 1 pct impurity. An analysis of the metal showed approximately 1800 ppm C in the powder while the sheet trimmings contained less than 500 ppm C. Spectrographic analysis showed minor amounts of Ca, Cr, Fe, Mn, Si, Ti, V, and Zr in both forms of the columbium. No commercial source of vanadium having the ductility and purity desired was available to the authors at the beginning of this investigation. As a result, all of the vanadium used in this study was prepared by the bomb reduction of vanadium pen-toxide with calcium employing the method reported by Long.' Yields of massive vanadium normally were about 80 pct. Chemical analysis of the vanadium prepared in this manner showed the presence of 200 to 500 ppm N and 800 to 1000 ppm C. Minor amounts of Ca, Fe, Mn, Si, Zr, Cr, and Cb were detected by spectrographic analysis. This vanadium metal was ductile and was cold rolled into 5 mil sheet. Annealing was not necessary during this rolling and the metal retained its cold-rolling characteristic after are-melting. Preparation of Alloys: The Cb-V alloys were prepared by melting pieces of vanadium sheet togethel-with columbium in the form of sheet or pellets of powder. The melting was carried out under argon in conventional arc-melting equipment employing a tungsten electrode and a water-cooled copper crucible. Each alloy was remelted three or four times, inverting the alloy after each melting in order to assure complete mixing. Alloys normally were obtained as round flat disks, weighed approximately 70 grams, and had roughly the shape of a disk 1 1/2 in. in diameter and 1/4 in. thick. Half of each alloy

Jan 1, 1955