Search Documents

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C'. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h'b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,' by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K' is the value for the Fe-S binary solution. and the limiting value of K' in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1' that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

By Douglas J. Robinson

A pilot scale process has been developed to separate mercury, tin, silver, and copper from dental amalgam scrap. Laboratory research led to a process which was operated in 55 gallon drum sized reactors to treat 2000 Tr oz charges of scrap per day. This paper discusses the development work, presents a flowsheet and gives an indication of the equipment necessary to carry out the process on a commercial scale.

Jan 1, 1984

By J. E. Wilson, F. P. Lebar

TYPICAL of southwestern Wyoming are coal structures that dip from 4° to 17°. Those at the Reliance and Winton mines of the Union Pacific Coal Co. average 91/2 and 15°, respectively, and dip almost directly to the west. By using a hoist for main haulage, a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 ft. a two-entry system is driven to the north and to the south. In both fields, which are nongassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy loader was introduced into The Union Pacific Coal Company's operations, slopes, aircourses, and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 ft. and entries at 230 ft. Connections to the workings above were made by driving up the pitch 75 ft. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a I¼-in. hemp rope dou- bling around it and having me end attached to the car and the other to the mule. The mulc, pulling downhill, raised to the working face a small wooden car of one-ton capacity. With the introduction of mechanical loading, mule haulage and small wooden cars disappeared and auxiliary hoists, electric locomotives, and steel cars with a capacity of 4 tons were substituted. Development work was done during two or three shifts of the 24-hr. period. Driving of haulage slopes down the pitch by hand continued. Crosscut intervals were changed to Ioo ft. and the crosscuts were driven with shaking conveyors. With the use of a 90° swivel, aircourses and manways were driven up the pitch. Entry intervals were changed from 230 ft. to 300 feet. Mobile loaders of the Joy type were first employed by this company in the year 1923 at Hanna, Wyo. In 1928, two 4-BU Joy loaders were transferred from Hanna to Winton No. I mine, where they were used in driving slopes and entries. At the time of transfer, the machines were about worn out and were not suited to the steep pitch, therefore frequent breakdowns occurred. However, experience justified the belief that the mobile loader was fitted for driving slopes in this field. During 1937 a unit was installed in Reliance No. 7 mine, and during 1939 one in Winton No. 7½ mine. With the introduction of this type of mobile loader, a new era of development began. Speed undreamed of in hand-loading days became a reality. The cost of development down the pitch has been reduced until it

Jan 1, 1942

By H. M. Morse

This report on oil and gas development in Mississippi covers the period from Jan. I, 1944, to Dec. 31, 1944: Salt Domes During the year six salt domes were drilled for sulphur, but no commercial sulphur deposits were found. One salt dome, the Bruinsburg, in Claiborne County, has produced gas- at 935 to 940 ft' in Moody's Branch marl. The Stringer salt dome in Smith County and the Ruth salt dome in Lincoln County both had a slight showing of heavy oil. Other salt domes have been dry. In addition to the Bruinsburg dome, the Allen salt dome, in Copiah County, and the Richton salt dome, in Perry County, were discovered in 1944; also the Sumrall dome, in Covington County. New Oil Fields Baxtemille Oil Field.—The Baxterville oil field was discoveredby the Gulf Refining Co, in sec. 7, T. I N., R. 16 W., Lamar County. At the end of the year this field had one oil well, with two active operations. Production for 1944 was 1047 bbl. of oil. GwinvilLe Field.—Gwinville field was discovered by S. W. Richardson, in sec. 24, T. 9 N., R. 19 W., Jefferson Davis County. This discovery well was a gas-distillate well, the oil being crystal clear. At the end of 1944 there were two gas wells and one oil well in the field. The oil well is approximately 2 1/2-miles from the gas- distillate wells. Gas production was 55,801 M cu. ft. and the distillate production was 2644 barrels. Heidelberg Oil Field.— The Gulf Refining Co. discovered the Heidelberg field in sec. 30, T. I N., R. 13 E., Jasper County, in January 1944. This field has by far exceeded the other 1943 and 1944 discoveries, having approximately 56 oil wells, 7 dry holes, and 10 active wells at the end of the year. Production to Jan. I, 1945 was 1,441,192 bbl. of oil. Mallalieu Oil Field.—The california Company discovered the Mallalieu oil field in set. 10, T. 7 N., R. 8 E,, Licoln. County. At the end of the year there was one well in the field with three active operations. Production was 32,303 bbl. of oil. Old Oil Fields Brookhaven Oil Field, in Lincoln County, has one oil well, which produced 2590 bbl. of oil during 1944. CarY Oil Field, Sharkey County1 has only one producing well, which produced 11,818 bbl- of oil during the Year- In Cranfield Oil Field, dams County, II oil wells and two gas-distillate wells were drilled in 1944 and there were five active wells on Dee. 31, 1944- The total production for the Year was 5251422 bbl-of oil. The gravity of the oil is 40" to 54.9'- In Eucutta Oil Field1 Wayne County1 34 oil wells were completed during 1944. There were five dry holes and six active wells at the end of the year.. The field produced 454,332 bbl. of all d the average gravity is 25" Flora Oil Field, Madison County, pro-

Jan 1, 1945

By J. E. Wilson, F. P. Lebar

TYPICAL of southwestern Wyoming are coal structures that dip from 4° to 17°. Those at the Reliance and Winton mines of the Union Pacific Coal Co. average 91/2 and 15°, respectively, and dip almost directly to the west. By using a hoist for main haulage, a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 ft. a two-entry system is driven to the north and to the south. In both fields, which are nongassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy loader was introduced into The Union Pacific Coal Company's operations, slopes, aircourses, and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 ft. and entries at 230 ft. Connections to the workings above were made by driving up the pitch 75 ft. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a I¼-in. hemp rope dou- bling around it and having me end attached to the car and the other to the mule. The mulc, pulling downhill, raised to the working face a small wooden car of one-ton capacity. With the introduction of mechanical loading, mule haulage and small wooden cars disappeared and auxiliary hoists, electric locomotives, and steel cars with a capacity of 4 tons were substituted. Development work was done during two or three shifts of the 24-hr. period. Driving of haulage slopes down the pitch by hand continued. Crosscut intervals were changed to Ioo ft. and the crosscuts were driven with shaking conveyors. With the use of a 90° swivel, aircourses and manways were driven up the pitch. Entry intervals were changed from 230 ft. to 300 feet. Mobile loaders of the Joy type were first employed by this company in the year 1923 at Hanna, Wyo. In 1928, two 4-BU Joy loaders were transferred from Hanna to Winton No. I mine, where they were used in driving slopes and entries. At the time of transfer, the machines were about worn out and were not suited to the steep pitch, therefore frequent breakdowns occurred. However, experience justified the belief that the mobile loader was fitted for driving slopes in this field. During 1937 a unit was installed in Reliance No. 7 mine, and during 1939 one in Winton No. 7½ mine. With the introduction of this type of mobile loader, a new era of development began. Speed undreamed of in hand-loading days became a reality. The cost of development down the pitch has been reduced until it

Jan 1, 1942

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By N. Mungan

Laboratory water floods were performed in oil-wet and waterwet alundum and Torpedo cores, displacing a refined oil with n-hexylamine or Triton X-100 solution. Also, some floods were performed in which a sucrose solution was displaced with n-butyl alcohol. The Purpose ot the tests was to see if the oil recotlery could be increased and to examine what role the inter-facial tension reduction and wettability change play in the recovery mechanism. it was found that the chromatographic transport of amine was influenced by core wettability. In oil-wet cores, the rate of advance of the amine band could be predicted from equilibrium chromato-graphy, while in water-wet cores the amine band moved faster than predicted, indicating a non-equilibrium process. By reducing the interfacial tension to 1.1 dyne/ cm, oil recovery was increased. More oil was recovered from Dri-filmed cores than from water-wet cores. Reversing the wettability of the porous media from oil-wet condition also resulted in some additional oil recovery. Neutral wettability floods did not increase oil recovery. INTRODUCTION Interfacial forces in petroleum reservoirs are responsible for retention of large quantities of residual oil. Increasing exploration costs have created an incentive to attempt recovery of this residual oil by new and novel processes. One novel process involves changing the interfacial forces by introducing a chemical into the reservoir during water flooding. Recently, several investigators have carried out laboratory displacement tests using amines. lt3.4 The amines adsorbed onto initially water-wet core surfaces, changing them to oil wet. Additional oil was recovered when the cores were flooded in a manner reversing the. wettability from oil-wet conditions. In all these studies, the wettability reversal was considered responsible for increased oil recoveries although it was noted that amines also reduced oil-water interfacial tension. In the present study, displacement experiments were performed in water-wet and Dri-filmed cores. The purpose was to separate the effects of lowering the interfacial tension from changing the wettability. LABORATORY STUDY All experimental data given in this paper have been obtained at a temperature of 70F + 1 and prevailing atmospheric pressure. FLUIDS AND MATERIALS The oil used in these experiments* was washed with H2S04 and passed through two 100-200 mesh silica-gel beds to remove unsaturates and surface active impurities. Normal hexylamine** of practical purity was used, and the alundum cores*** were composed of nearly pure A1203. Fused quartz (SiOi) and Lucalox (A12 )t plates were used in the contact angle measurements. DISPLACEMENT TESTS Displacement tests were performed in alundum and Torpedo cores. Before displacement runs, cores were acidized with 0.1 normal HCI, flushed with distilled water and fired at 1,200F to make them water wet. This procedure also reduced water sensitivity of the Torpedo cores. Oil-wet cores were prepared from water-wet cores by flowing several pore volumes of 1 per cent by weight Dri-film SC-87 solution in heptane through the cores, flushing the cores with nitrogen, evacuating, and finally heating the cores at 300F for 4 or 5 hours. Between floods, cores were cleaned by conventional procedures and treated again as above.

Jan 1, 1965

By Howard R. Keil

Reactor at Carlton mill successfully calcines pyrite-telluride flotation concentrate for cyanidation. CARLTON mill in the Cripple Creek district, 45 miles southwest of Colorado Springs, Colo., has been in operation for approximately three years, treating the custom sulpho-telluride ores formerly handled by the Golden Cycle mill in Colorado Springs. At the new mill the pyrite-telluride flotation concentrates have been roasted, prior to cyani-dation, in a Dorrco FluoSolids reactor, which has proved capable of yielding calcine readily amenable to cyanidation. Incoming ores are crushed at Carlton to % in. and sampled in 30 to 75-ton lots before the individual lots are mixed in the fine ore bin. The composite ore then goes to the grinding circuit. Classifier overflow from the grinding circuit is treated by flotation to produce a concentrate containing approximately 85 pct of the values in 5 pct of the weight. The flotation concentrate goes to the FluoSolids reactor prior to cyanidation. Cyanide solution values are recovered by zinc dust precipitation. Flotation tailings are thickened and cyanided, the values from this part of the circuit being recovered from solution by activated carbon. Gold values in the flotation concentrates consist of a small amount of finely divided metallic gold; the tellurides, sylvanite and calaverite; and gold very intimately associated with the pyrite. The metallic gold and a part of the telluride values can be extracted from the concentrates by cyaniding without roasting. However, extraction on the tellurides by this method is not satisfactory, and the pyrite values are so intimately associated with the pyrite that very fine grinding and cyanidation for a prolonged period under ideal laboratory conditions does not yield good recovery. Upon roasting, the tellurides are oxidized to very finely divided metallic gold which is readily soluble in cyanide. The pyrite is oxidized mainly to a porous iron oxide which allows cyanide solution to penetrate to gold particles and take them into solution. Feeding the Reactor Flotation concentrates move by gravity to a thickener. Thickener underflow is discharged at approximately 60 pct solids, by means of a diaphragm pump, into a storage and blending agitator. From here the concentrates are pumped to a disc filter. The filter cake, at 84 to 88 pct solids, drops directly into a repulper where it is repulped into a slurry of 78 to 80 pct solids. The repulped filter cake flows into a 6x6-ft slurry agitator from which it is fed directly into the reactor by the Moyno pump. The Moyno pump has eliminated a large number of difficulties that were first encountered in feeding a wet concentrate to the reactor. On the original installation in Canada a screw feeder was used to introduce the filter cake directly into the reactor. Since the reactor is under a slight positive pressure it was necessary to have a suitable seal to prevent gas escaping from the reactor at this point. When the concentrates produced in flotation were coarse or granular they could be readily fed to the reactor but when fine-textured, clayey concentrates were produced a great deal of trouble was encountered.

Jan 1, 1955

By Michael Hoch, Seong Kwan Rhee

The ternary system Zr-Cr-0 was investigated at 1200°, 1500°, and 1700°C. The isotherms at these temperatures were determined by metallographic and X-ray diffraction analysis of carefully selected alloys. AS a part of a series of investigations1-4 of the ternary and quaternary phase diagrams on refractory metals and their compounds, the ternary system Zr-Cr-O was investigated at 1200°, 1500°, and 1'700°C. The binary diagrams Zr-Cr, Zr-O, and Cr-0 as reported by Hansen5 and Levin et a1.' and the existence of a ternary coompound ZrsCrsO (q-carbide structure a. = 11.96A) provided a good base for this investigation of the Zr-Cr-O phase diagram. MATERIALS The materials used and their suppliers were: Zirconium powder, 99.4 pct pure, Charles Hardy, New York; Zirconium dioxide, Fairmount Chemical Co., Newark, N.J.; Chromium powder, 99.85 pct pure, Fairmount Chemical Co., Newark, N.J.; Chromium sesquioxide, 99.86 pct pure, J. T. Baker Chemical Co., Pillipsburg, N.J. Though the materials used were not "hyperpure", the impurities present do not affect the results (lattice parameters, phase boundaries) within the experimental accuracy. EQUIPMENT AND PROCEDURE The detailed procedures and equipment used for this investigation were similar to those described elsewherel' "ith the exception that in this study an induction-heated argon-atmosphere furnace was used. The latter furnace was used to prevent the vaporization of chromium metal in samples in the higher temperature range (above 1200°C). The tungsten crucible was induct ion-heated in a vertical quartz tube filled with argon gas. The quartz tube was 1-1/2 in. in diameter and 10 in. long; it was connected at the top and bottom to water-cooled copper plates. The argon gas of a purity 99.995 pct was further purified by being passed through zirconium metal chips which were maintained at 800°C in a silica tube 1 in. in diameter and 30 in. in length. The furnace was flushed with argon gas for an hour before starting heating; during heating, a slight (3 cm oil) overpressure of argon was maintained in the system. Power was supplied by a 20-kw Ther-Monic Induction Generator. The samples rested on a tungsten-wire basket; the wire basket was connected to a tungsten wire which passed through the tungsten crucible lid, and entered the system on top through a Wilson-type seal. By pulling on the wire, the sample was removed from the crucible and dropped to the water-cooled copper base of the furnace. Because of the presence of argon gas, the cooling of the sample was even more rapid than in the vacuum furnace.' EXPERIMENTAL RESULTS AND DISCUSSION 1) Isothermal Section at 1200°C. The compositions investigated have been numbered within the phase diagram, Fig. 1, and all the pertinent information about the samples can be found in Table I. This table lists the composition of the samples, the phases present in the room-temperature diffraction patterns, the phases detectable in the microstruc-ture, and calculated lattice parameters of the a-zirconium phase. The shapes of the various phase

Jan 1, 1964

By Walter B. Lenhart

Introduction and Importance of the Industry Sand, as described in this chapter, is a crude product used for ballast on railroads and highways, and as the fine aggregate in concrete, mortar, plaster and in asphalt paving materials. The sand used in glass, as a molding sand, and as a source of silica is described in Chapter 43. Sand and gravel together constitute the mineral raw materials of largest volume produced from the earth. In 1958, as reported by the U.S. Bureau of Mines,21 680,080,000 tons of sand and gravel (including industrial sand) were produced in the United States. The nearest competitor was crushed rock of which 532,818,000 tons were produced. Coal, both bituminous and anthracite accounted for only 431,616,689 tons in the same year. In dollar value, sand and gravel were exceeded only by cement, crushed rock and fuels. Hence it is a major unit of the mineral-producing industry. As an example, one plant in California operates around the clock at an average rate of 1,500 tons per hour, and at peak intervals has shipped over 4,000 tons per hour, all by trucks. Nevertheless, it is controlled by one man through a panel of push buttons that control the crushing, screening, washing, grading, stock piling, and reclaiming of the products. Because sand and gravel are low-valued commodities, but are used in every construction undertaking in every city, village, farm, dam and highway, they are produced in almost every county in the United States and southern Canada, by thousands of individual operators, very few of whom operate in more than one community. Many operations, particularly those established to supply the needs of major dams that are under construction, or of major segments of new highways, are temporary in nature, and the equipment installed is more or less portable. Because of the bulky nature of sand and gravel, there is very little interstate movement, and almost no exports or imports, except a little movement back and forth across the border of the United States and Canada. First, the material needs definition. Definitions Sand and gravel have been defined as continuously graded unconsolidated materials that appear in the earth's surface as a result of the natural disintegration of rocks. Both normally appear together, but in a wide variety of sizes, types and range of size classification. The American Society for Testing Materials has tentatively revised its definition of "sand" as: granular material passing the 3/8-in. sieve and almost entirely passing the No. 4 (4760-micron) sieve and predominantly retained on the No. 200 (74-micron) sieve, and resulting from natural disintegration and abrasion of rock or processing of completely friable sandstone (ASTM Designation C 58-55T). The Society's tentative revision of its definition of "gravel" is: granular material predominantly retained on the No. 4 (4760-micron) sieve and resulting from natural disintegration and abrasion of rock or processing of weakly bound conglomerate (ASTM 125-55T). Sand and gravel deposits contain materials from the finest silt to the largest boulders. Chemical definition of the two materials is nearly impossible. Sand and gravel always are

Jan 1, 1960

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By E. W. Davis

ABOUT a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½ -in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about zoo per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½ in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2 1/2 kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1945

LIBERIAN ore has been called the richest iron ore mined in the world, and thus far, the output from the Liberian Mining Co.'s Bomi Hills mine has lived up to its reputation. Iron content has been variously given as 68.47 pct to 68.825 pct. A recent United Nations survey gave it first place, surplanting the previously top-rated Swedish product. The first shipment of Liberian ore to the United States reached Baltimore in June, 1952 and went into blast furnaces at Republic Steel's Cleveland plant, where excellent results were reported. The physical make-up of the ore was hard, dense lumps, free of fines and with ideal size distribution. The Bomi hills mines were scheduled to be in full operation by the end of 1952. At the close of 1951, 200,000 tons of ore had been delivered to Baltimore. Liberian Mining Co. states that production is about 90,000 tons of ore per month at present. Between 1200 and 1500 men are employed at the mine site, with about 25 pct of them Americans. The Bomi Hill project was financed with the aid of the Export Import bank, which loaned Liberia Mining part of the sum needed to initiate and put the development into production. No definite expansion plans are in the making but extensive diamond drilling is being pursued. Original estimates of annual production for Bomi Hills ran in the neighborhood of 1.5 million tons, but the figure is no longer applicable. Liberia's potential as an iron producing country has been known for a long time, but the physical obstacles in the way of large scale production were such as to prohibit even contemplation of the project. Until recent years, the only route from the mine site to Monrovia was a foot trail. Once to the coast, over swamps and unbridged rivers, the ore was still useless because of the lack of loading facilities. Transportation Solved One problem was solved with the completion of the artificial harbor at Monrovia. Harbor construction was well under way when the mine project began in 1948. The island location of Monrovia also made the building of a bridge across the St. Paul River necessary. The 980 ft reinforced concrete structure, accommodating railroad and vehicular traffic, was opened in 1949. Meanwhile, preliminary work on railroad construction started. Grading was completed quickly. In April, 1951, the first train made the trip from Monrovia to the Bomi Hills. About half of the cost of the entire project went into railroad construction. More than 2200 men, often forced to resort to primitive methods, were engaged in clearing a path through the heavy forests between the mine and port. Swamps were drained and filled, and bridges, including the William V. S. Tubman, named for the Liberian President, were constructed. At the port, a Robbins Conveyor Belt Co., orehandling plant was installed. Ships can be loaded from the stockpile at the rate of 3000 tons per hr and vessels need spend only one day in port. Liberian Mining is operating under an 80 year lease, giving the company exclusive mining rights to all minerals, except gold, platinum, and diamonds, within a 40 mile radius of Bomi Hills. The contract provides a fixed royalty to the Liberian Government of five cents per ton of ore extracted, and a premium -based on the New York market price for Bessemer-grade pig iron. The entire project started because an American,

Jan 1, 1952

By James B. Macelwane

THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these 'fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the. January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1952

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By Ö. Valla, A. Muan, K. Grjotheim

The solid miscibility gap between CaO and "FeO" in the system CaO-"FeO" in contact with metallic iron gradually closes as MnO is added as a third component. On the liquidus surface of the system CaO-"FeO"-MnO, this situation gives rise to a boundary curve which originates in the bounding system CaO-''FeO", proceeds a short distance into the composition triangle of the ternary system, and then vanishes. A new approach has been used to follow the course of this boundary curve. It is shown that the curve vanishes at a much lower temperature and at much lower MnO contents than has been inferred previously. The oxides CaO, "FeO", and MnO together with SiO2 are the major components of the slag phase formed in the basic oxygen process. Hence, the system CaO-"Fe0"-MnO is of considerable technological interest. In addition, the system is theoretically interesting. The three oxides above all have sodium chloride structure. The size differences among the cations are such that in the bounding "binary"* systems CaO-MnO and "FeO"-MnO complete solid-solution series are formed,1,2 whereas in the system CaO-"FeO" there is only limited mutual solubility in the solid state,3 see Fig. 1. Hence, a solid miscibility gap exists in a part of the "ternary"* system Ca0-"Fe0"-Mn0, and a liquidus boundary curve originates at the peritectic point, point a in the insert in Fig. 1, in the system CaO-"FeO", extends a certain distance into the ternary system, and then vanishes. Very little quantitative information on the system Ca0-"Fe0"-Mn0 is available in previous literature. Fischer and Feischer4 sketched isothermal sections at 1600° and 1700°C, and estimated that the vanishing boundary curve extends to approximately 1650°C and a composition of 42 wt pct MnO. The work to be described in the following was aimed at locating experimentally the "vanishing" liquidus boundary curve, determining its end point, and deriving representative isothermal sections below and above the temperature of the end point of this curve. EXPERIMENTAL METHODS The phase relations were determined by the well-known quenching method. (For a description of this method as applied to oxide systems, see the original paper of Shepherd, Rankin, and wright.5) Prereacted oxide mixtures of desired compositions were contained in iron crucibles and heated in a vertical tube furnace in an atmosphere of purified nitrogen. After equilibrium was judged to have been attained, the samples were quenched to room temperature, the phases present were identified by microscopic and X-ray examination, and total iron oxide contents were determined by chemical analysis. "Fisher Certified" reagents (MnCO3, CaCO3, Fe2O3, and Fe) served as starting materials. The calcium carbonate and ferric oxide were heated in air at 400° and 800°C, respectively, for 24 hr prior to use. Manganese oxide was prepared by decomposing the carbonate in a graphite crucible in hydrogen atmosphere at 1000°C. The product was ground under acetone to -100 mesh. The iron powder was used directly without any preparation. Dicalcium ferrite was used as a starting material for some mixtures. It was made by mixing some of the above prepared CaCO3 and Fe2O3 in proportions corresponding to the formula 2CaO. Fe2O3. This mixture was then fired in air for

Jan 1, 1969

By J. J. Cosgrove, J. E. Warren

A general model which approximates the effect of cross- flow has been developed to give a practical method for predicting the waterflood behavior of a stratified reservoir. The model is based on a modification of Dietz's theory and allows for variations in both the permeability and hydrocarbon pore volume. In the particular cases considered, it is assumed that the permeability can be characterized by a log-normal distribution and the hydrocarbon pore volume by a normal distribution. A simple graphical method which enables the practicing engineer to predict the behavior of a stratified system is presented The results obtained by the proposed method are compared with those obtained by the Dykstra-Parsons method. As a result of this study the following conclusions have been drawn: (1) The effect of cross-flow in a stratified system can be appreciable, particularly at very favorable or very unfavorable mobility ratios; (2) Under normal conditions, the effect of variations in the hydrocarbon pore volume can be neglected; and (3) The failure to use all of the available permeability data can lead to large errors in the prediction of the behavior of a stratified reservoir. INTRODUCTION Various methodshavebeenproposedto characterize and to predict the waterflood behavior of a stratified reservoir. Most of the methods assume that the reservoir is composed of discrete homogeneous continuous layers. With this model, the degree of stratification can be measured by several parameters based on core-analysis data. Among these are the Lorenz coefficient1 and the variation of a log-normal permeability distribution? The behavior of stratified systems is usually predicted by the Stiles, Dykstra-Parsons method or some modification of these. In both of these methods the reservoir is divided into discrete homogeneous layers with no cross-flow between layers. In the Stiles method the mobility ratio is assumed to be equal to unity while in the Dykstra-Parsons method it is allowed to take on any value. Other predictive methods have been proposed; method allows for cross-flow between the beds and a method by Schmalz and Rahme6 correlate.s the recovery directly with the Lorenz coefficient. In this new approach, which is essentially a continuous analog of Hiatt's method, the effects of both mobility ratio and cross-flow between the beds have been included. It is assumed that the permeability can be represented by a log-normal distribution and the hydrocarbon pore volume or porosity by a normal distribution. These types of distributions have been observed by several authors, 1,2,4 and most field data seem to confirm their observations; e.g., if these distributions are assumed and there is a 1:l correspondence between porosity and permeability samples, the commonly encountered linear relationship between porosity and the log of permeability is obtained. Since, in many field cases the permeability and poro sity data are truncated or cut-off at predetermined upper and/or lower values, the effect of discarding part of the data was investigated with the proposed method. A better technique for truncating the data is suggested. THEORY In the derivation of the method to be described in this paper the following assumptions are made: 1. Capillary forces are negligible per se; their effects are only manifest in the relative permeability curves. 2. The fluids are immiscible, incompressible and homogeneous. 3. The reservoir is horizontal and uniformly thick; it is initially liquid saturated i.e., connate water and oil. 4. The reservoir is composed of discrete layers, each having its own permeability, porosity and connate water saturation; each layer is homogeneous,

Jan 1, 1965

By F. A. Veer, W. G. Burgers, B. H. Kolster

Starting-- from Cu-Si diffusion couples a study of diffusion in the intermetallic compound Cu3Si of the Cu-Si system has been made. Mmker experiments showed copper to be the diffusing element. From the rate of growth of the Cu3Si phase diffusion coefficients were derived. The activation energy for diffusion is 18.6 kcal per mole. The couples show some interesting microscopic features, for which a tentative explanation is given. THE synthesis of dimethyldichlorosilane, (CH3)2SiC12, an important compound in the manufacture of methyl-silicones, takes place at the surface of a thin Cu3Si layer deposited on a mass of silicon particles."' By passing CH3C1 vapor at about 350°C, silicon atoms are consumed from Cu3Si in forming the volatile silane molecules, thus leaving copper atoms at the surface. It is well-known that copper acts as a poison for the above-mentioned reaction by catalyzing the dissociation of methylchloride.' However, no poisonous effect is observed, at least not before most of the silicon from the particles is converted into silane.3 This would be understandable, if either the copper atoms diffuse through the Cu3Si deposit to the underlying silicon or silicon atoms diffuse in the reverse direction to the copper, both processes resulting in the formation of new Cu3Si and so ensuring the proceeding of the reaction. In this paper experiments are described, demonstrating copper to be the diffusing element. Also a very low activation energy for the diffusion is observed. EXPERIMENTAL The silicon used contained 1 ppm Mg and 1 ppm Cu; the copper was spectroscopically pure (Fe: 2 ppm; Ag, Mg, Si: 1 ppm). The copper and silicon samples were prepared in the form of blocks of approximately 10 by 10 by 5 mm with two parallel sides by spark-machining. The blocks were ground on emery paper (grit 600), etched (copper with nitric acid, silicon with a 4:l nitric acid:hydrofluoric acid mixture), and cleaned with alcohol. As the brittleness of the silicon did not allow a welding procedure to prepare the diffusion couples, the copper and silicon blocks were pressed together in a steel clamp. The pressure exerted by the clamp brought about contact between the parts of the couple and so ensured proceeding of the diffusion. The couples were heated in a vacuum furnace (about 10"5 Torr). The temperature was stabilized within 1 pct. After a heat treatment a section parallel to the direction of diffusion was examined in the microscope and in the X-ray scanning microanalyzer. To determine whether copper or silicon is the diffusing element marker experiments were carried out using tungsten wires with a 20-p diam. EXPERIMENTAL RESULTS Figs. 1, 2, 3, and 4 give micrographs of diffusion zones of Cu/Si couples. Analysis by the electron mi-croprobe of the Cu/Si samples after a definite heat treatment revealed the existence of only one intermetallic phase as can be seen from the line scan shown in Fig. 5. From the X-ray diffraction pattern it could be deduced that this phase was CU 3 Si.4 Even when diffusion zones of considerable width (up to 600 p) were obtained, no other phases occurring in the Cu-Si system could be detected, neither by the electron microprobe nor by X-ray diffraction analysis. The optical anisotropy of the Cu3Si phase made it possible to observe the columnar shape of the crystal-

Jan 1, 1969

By Tell Ertl

The term oil shale is defined. Foreign oil-shale developments are outlined briefly. The richest and most extensive oil-shale deposits in the United States lie in western Colorado. The Bureau of Mines is opening two adjacent areas for underground mining. in western Colorado. From the first area the oil shale is mined selectively as required by the retorting plant. The second area is being developed as a unit of a full scale oil-shale mine to ascertain the most practical methods of mining oil shale and to determine costs. In both of these mining areas, research will be carried on to develop new and improved practices for mining oil shale. Introduction Oil shale is a sedimentary rock containing a solid mineraloid of indefinite composition known as kerogen. On heating oil shale, the kerogen undergoes thermal decomposition and some of the vapor products of the decomposition can be condensed as shale oil. Oil from shale can be a major source of liquid fuels since extensive deposits of oil shale are known to exist throughout the world. The United States considers the establishment of an oil-shale industry only when doubt exists of the adequacy of the domestic supply of crude petroleum. On the other hand, oil shale is not strange to foreign oil men. The industry is an old one in other parts of the world. The French industry has been in existence since 1838, the Scottish since 1859, the Australian since 1860, the Estonian and Swedish The since World War 1, and the Manchurian industry since 1929. The most highly exploited oil-shale deposits are the Carboniferous shales of Scotland. About 20 seams ranging from 4 to I2 ft in thickness are worked. The yield during recent years in scotland has been 18 to 25 gal of shale oil per ton, from 3&"30'000 tons per year' The French and Swedish oil-shale deposits are of lower grade than the Scottish. The Estonian oil-shale deposits are 7 ft thick, and the oil yield averages 50 gal per ton. Over 1,000,-ooo tons are mined each year, half of which is used directly as fuel to substitute for coal and the other half is used for the production of oil. Immense deposits of oil shale that will yield 10 to 15 gal per ton exist in Germany. Because of the impending loss of the Rumanian and Polish oil fields and the bombing of synthetic liquid fuel plants, the Nazis in 1943 started a large-scale oil-shale program in Germany. By V-E Day, it is said, oil-shale production had reached the rate of 2500 tons per day and rapid expansion of the industry was imminent. Australian oil shale, known as torbanite, occurs in beds 2 to 6 ft thick. It is of a very high grade and on retorting yields 80 to 160 gal per ton. The oil-shale industry of Manchuria was the largest in the world during the past decade. The well-known Fushun coal deposit in Manchuria has an overburden of 500 million tons of oil shale about 450 ft thick that will yield 10 to 15 gal of shale oil per ton. The oil shale is

Jan 1, 1949