Search Documents

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita da zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetarem a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução da ZF foi 85%, para 100% CO, 1373K e 105 min, e 52%, para 50% CO, 1373K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373K durante 105 min. no caso da redução do EAFD

Aug 17, 2017

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019

By Douglas Glenn Stalheim

The uniformity of the final cross sectional microstructure and subsequent final mechanical properties and shape of structural steels is dependent on the type or types of recrystallization behaviors that are created. There are three main recrystallization behaviors that are the foundation of the metallurgy created during production. Alloy design and subsequent processing design strategy drive how much of each recrystallization behavior is created through the cross section of the product. Carbon manganese steels create only one basic behavior while the addition of microalloys, in particular niobium, can add two additional behaviors. The behaviors are intertwined with each other and build upon each other. The three behaviors are Type I, static recrystallization, Type II, no-recrystallization, and Type III, metadynamic/dynamic recrystallization. How much of each behavior is generated through the cross section through the production influences the final transformed microstructure and corresponding mechanical properties and shape performance. This paper will discuss the three behaviors, how they are generated, how to identify which behavior is occurring through modeling or actual mill data. Actual examples from production will be discussed.

Aug 16, 2017

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Valeria Romina Stricker

Acerbrag es una empresa Argentina siderúrgica de 50 años de trayectoria, desde el año 2007 pertenece al grupo Votorantim de origen Brasilero. Se dedica a la elaboración de aceros largos para la construcción. La planta industrial cuenta con un proceso de acería integrado, horno eléctrico, horno cuchara y máquina de colada continua. La materia prima es 100% chatarra, característica que la diferencia del resto de las acerías del país. Debido a esto el enfoque principal de este proyecto es reducir el costo de fabricación mediante un “empobrecimiento” de la carga metálica a partir de la flexibilización de los límites de especificación. Esto implica un mayor control del desempeño de los procesos a fin de detectar posibles desvíos, para ello fue necesario implementar la utilización de herramientas estadísticas y gráficas para su monitoreo. La modificación en el mix de fabricación no muestra una alteración significativa en la composición química y propiedades mecánicas de los productos terminados, situación favorable para la continuidad del proyecto. Se observa además, de la reducción de costo esperada, una ventaja en la operación del patio de chatarra y el proceso de acería y en la utilización de chatarras con altos niveles de residuales tales como Cr – Ni.

Aug 16, 2017

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By Edgar Ivan Castro Cedeño

En la producción de aceros limpios el control inclusionario es crítico para la obtención de un producto que cumpla con los requerimientos de calidad. El análisis de la distribución de tamaño de inclusión mediante modelos estadísticos permite estimar la incidencia de inclusiones en el producto solidificado a partir de mediciones tomadas en muestras relativamente pequeñas. En seis coladas de acero bajo carbono desoxidado con aluminio se tomaron muestras de acero a lo largo del procesamiento en horno olla y colada continua. Las muestras se prepararon para estimar mediante análisis metalográfico los tamaños de inclusión. Los datos de tamaño de inclusión se analizaron mediante modelos estadísticos de valores extremos, se hace una comparativa entre la distribución Gumbel (que forma parte de la norma ASTM E-2283) y la distribución Generalizada de Valores Extremos (GEV). Mediante una prueba de hipótesis con el estadístico Anderson-Darling, análisis de cuantiles y con la función de supervivencia se demuestra que la población inclusionaria se describe de una mejor manera con la distribución GEV. Finalmente se da un estimado de la incidencia probable de inclusiones en el producto solidificado.

Aug 16, 2017

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017