Search Documents

By Luciano Henrique Andrade de Resende, Maria Rita Oliveira Rebouças

O processo de Monitoramento Controles, realizado pela área de Governança, Riscos e Compliance, requer preparação e verificação de um grande volume de dados. Isso feito de forma manual e com a necessidade de cruzar dados de diferentes fontes, torna o processo bastante complexo, impactando diretamente na periodicidade e acurácia dos testes. O objetivo de trabalho era prover uma ferramenta e uma metodologia que fosse capaz de automatizar esse processo, tornando-o contínuo e possibilitando análise de uma grande massa de dados, proveniente de diferentes fontes e com uma saída padronizada. Após análise de ferramentas de mercado e a realização de provas de conceito, foi definida a ferramenta e modelo de trabalho a ser aplicado. O resultado foi a implantação de um processo de Monitoramento Contínuo de Controles (MCC) que traz: ganho de produtividade, ao permitir que testes sejam executados de forma automática; ganho de eficiência, por permitir realizar o teste em toda a base de dados, sem necessidade de amostra; aumento na assertividade, por reduzir probabilidade de erro humano provenientes de atividades manuais; além de retorno financeiro e mitigação de riscos.

Oct 1, 2019

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By José Marcelino dos Reis

Com o empobrecimento das jazidas minerais, os novos projetos industriais e as expansões das atuais usinas de tratamento de minério de ferro, em sua grande maioria, têm sido concebidos/ adaptados para processar itabiritos pobres para produção de pellet feed. Neste contexto, a otimização dos processos já existentes e/ou a implantação de projetos mais eficazes, são medidas fundamentais para a redução do teor de ferro no rejeito; consequentemente, maximiza-se a produção e a vida útil da jazida, além de reduzir os custos operacionais. O processo de flotação reversa de minério de ferro da usina de concentração de Brucutu responde por expressiva parcela de produção, sendo constituído por quatro estágios de concentração: rougher, cleaner, recleaner e scavenger. O concentrado final é produzido no estágio recleaner e o rejeito final no estágio scavenger, cujo teor médio atual é de 18% Fe. Objetivando reduzir o teor de Fe no rejeito scavenger da flotação para teores próximos a 10%, foi realizada uma série de testes exploratórios em bancada em diferentes faixas de pH, com adição de soda caustica e/ou amido gelatinizado. Os resultados obtidos em escala de bancada se mostraram bastante satisfatórios apresentando considerável ganho de recuperação mássica/ metalúrgica, o que motivou a realização de um projeto para viabilizar a implementação desta proposta.

Aug 1, 2018

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Thiago Pinto Silva

A Usiminas implementou dois ensaios para caracterização de minérios de ferro na sinterização, intitulados assimilação e penetração de fase líquida. O primeiro tem como objetivo avaliar as fases mineralógicas, a formação de poros e a resistência mecânica de partículas nucleantes e aderentes por meio da reação do minério com o calcário. O segundo objetiva medir o comprimento da penetração da fase líquida formada entre a calcioferrita e o minério. No presente trabalho, são descritas as principais características e potencialidades desses novos testes, os quais foram utilizados para a avaliação do comportamento metalúrgico de seis minérios distintos. Os resultados obtidos de assimilação e de penetração da fase líquida foram comparados com as características mineralógicas e químicas dos minérios, sendo observada uma boa correlação entre essas características e os resultados dos novos testes. Verificou-se também que a análise tradicional do minério não é suficiente para estimar seu comportamento metalúrgico na sinterização, o que reforça a importância da utilização dos novos testes implementados. Além disso, permitem avaliar o comportamento dos minérios em altas temperaturas, auxiliando na escolha da carga de minérios mais adequada para a sinterização.

Aug 1, 2018

By Danilson Gonçalves de Melo e Silva

O balanço de energia realizado em um forno de aquecimento de tarugos apresentou rendimento de 53%. A maior perda energética estava relacionada ao sistema de refrigeração dos skids, cujo valor calculado foi de 18%. Objetivando minimizar tais perdas, estudou-se a utilização de um novo tipo de revestimento refratário para esta região. O fabricante de refratários apresentou uma estimativa de ganho de 62%. Desta forma, a VBR planejou um teste para validar a eficiência do refratário proposto. Neste teste, o produto foi instalado em uma viga auxiliar. Esta viga foi instrumentada, e foram registrados dados de vazão, pressão e temperatura do fluido de refrigeração (água). Objetivando comparar estes valores com o material convencional anteriormente instalado, outra viga com as mesmas características (dimensões e posição no forno) também foi instrumentada. Posteriormente, foram feitos os balanços de energia em cada viga para quantificação das perdas de energia térmica. Os resultados encontrados mostram uma redução de 92% da perda térmica relacionada ao sistema de refrigeração dos skids. Considerando a eficiência do forno de 53% e a redução de 92% da perda térmica, estima-se uma economia de R$ 1.200.000 por ano.

Sep 25, 2017

By Carlos Alberto Perim

Devido à obstrução no distribuidor, os aços ultra baixo carbono estabilizados ao titânio apresentavam baixo sequencial de lingotamento na ArcelorMittal Tubarão (AMT). Foram identificadas práticas utilizadas na redução de obstrução nestes aços, que foram adotadas para a produção na AMT. Uma das práticas foi estabelecer uma relação entre alumínio e titânio com menor propensão à formação de compostos de alumina e óxido de titânio que se aglomeram na região da válvula superior do distribuidor. Também foram introduzidas melhorias no processo visando a melhorar a condição de fluxo na região próxima da saída do aço no distribuidor. Neste projeto, um aço UBC de maior volume de produção foi escolhido e novas práticas foram adotadas para sua produção. Amostras de aço foram retiradas de corridas produzidas nesta condição e foram enviadas para análise na ArcelorMittal Research USA. Os resultados mostraram melhorias nos índices de qualidade tanto em laminados a quente como em laminados a frio. Neste trabalho será apresentado um resumo das ações adotadas na AMT, que resultaram em um aumento do sequencial médio de distribuidor, permitindo atingir um máximo de 18 corridas. Os níveis de esfoliação com esta nova prática atingiram também nível mínimo histórico.

Aug 16, 2017

By Henrique de Araújo Resende

Em função do aumento constante da produtividade nos laminadores e linhas de processo de usinas siderúrgicas e de alumínio, está cada vez mais evidente a necessidade de aumentar as campanhas de produção dos mandris de bobinadeiras e desbobinadeiras, reduzir as paradas de manutenção das linhas além de minimizar ao máximo os custos com reparo e fabricação. Para isso, é importante conhecer os diversos projetos de mandris utilizados nos últimos anos, os maquinários envolvidos na fabricação e reparo desses equipamentos além de estar atualizado quanto às novas tecnologias que poderão ser aplicadas. Para possibilitar o entendimento descrito acima, este material será divido em 3 partes: Projetos SMS de mandris no Brasil; Condições de fabricação e reparo; Novas tecnologias. A SMS possui 58 mandris em operação hoje no Brasil estratificados entre os seus principais clientes, desde linhas de decapagem e laminação a quente até a saída do produto final após os laminadores a frio na galvanização e linhas de pintura e corte. Com isso, é possível estabelecer uma análise técnica do desempenho de cada equipamento e sobressalente de forma bem estruturada. Esse é o principal objetivo desse trabalho.

Aug 16, 2017

By Geraldo Lúcio de Faria

O parafuso Tirefond é um importante componente da via permanente ferroviária. Ele é um componente de fixação responsável por fixar a placa de apoio que, por sua vez, garante a estabilidade dos trilhos. Este componente é comumente fabricado no Brasil por processos de conformação mecânica a quente de aços baixo carbono. Entretanto, com o aumento da carga transportada por eixo de locomotiva nos últimos anos, este componente tem falhado de forma recorrente em serviço. Com o objetivo de entender os efeitos dos filetes do parafuso sobre o comportamento mecânico do componente, este trabalho apresenta um estudo sobre a susceptibilidade do parafuso à concentração de tensões sob carregamento estático. Análises químicas por espectrometria de emissão óptica, análises microestruturais por microscopia óptica, ensaios de tração e dureza foram realizados. Por meio da aplicação de modelos computacionais, foi possível determinar a distribuição de tensões ao longo do parafuso, assim como entender as principais causas destas falhas recorrentes. Fazendo-se uso de modelos matemáticos de mecânica de fratura, associados a simulações computacionais de carregamento estático, foram propostas modificações no projeto original do parafuso que prometem melhorar o seu desempenho em serviço.

Aug 16, 2017

By Maria Stella Vasconcellos Limaverde

A utilização de moinhos verticais na indústria mineral vem ganhando destaque nas últimas décadas, quando granulometrias mais finas passaram a ser exigidas, principalmente por tais equipamentos apresentarem maior eficiência energética para moagem fina e remoagem em comparação aos moinhos tubulares tradicionais. O dimensionamento destes equipamentos ainda é fortemente embasado por experiências em projetos similares, metodologias proprietárias dos fornecedores de equipamentos e plantas piloto, criando a necessidade do desenvolvimento de ensaios laboratoriais abertos e confiáveis para guiar tais trabalhos. Outro problema observado é a quantidade de material necessária para a realização dos ensaios, da ordem de ao menos 1 kg, o que pode ser um impedimento nos estágios inicias de um projeto, quando pouca massa de material proveniente de furos de sonda está disponível. Este trabalho apresenta o desenvolvimento de um ensaio laboratorial com moinho de jarro para dimensionamento de moinhos verticais segundo uma abordagem energética que utilize uma pequena massa, de aproximadamente 500 g. O ensaio proposto mostrou-se de maior praticidade em relação em relação ao ensaio com jarro maior, por utilizar aproximadamente metade da massa necessária e também apresentar boa aderência aos resultados industriais.

Aug 16, 2017