Search Documents

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By H. W. Gillett, A. E. RHOADS

In its study of methods for reducing metal losses in the non- ferrous metal industry, the Bureau of Mines has conducted a long series of experiments on electric brass melting and collected much data on the experiments of others. Reports bearing on this work that have already been published by the Bureau of Mines are Bulletin 73, "Brass-furnace practice in the United States," and Bulletin 77, "The electric furnace in metallurgical work." A comprehensive report describing the design and operation of all types of electric brass furnaces and showing their performance in experimental tests on a commercial scale is in course of preparation. However, commercial tests of several new and promising types of furnaces are still under way, the results of which should be included in any general discussion of the subject. For this reason it has seemed desirable to issue a preliminary bulletin giving the data on a type of furnace developed in one stage of the bureau's work.

Jan 1, 1918

By David E. Kaslow

In sampling dust laden air by drawing the medium into an inlet, some larger particles fail to follow the air and a true sample is not obtained. Inertia prevents particles from accelerating with the air as well as from turning sharp bends; also the particles' weight causes them to fall relative to the air. An analytic solution to the sampling efficiency calculation by Levin gives particle paths and sampling efficiencies for various particle sizes when the inlet can be treated as a point sink. However, the flow field in the neighborhood of an aspirating tube is quite different from a point sink flow. Employing Levin's solution in the outer field, trajectories in actual flow fields have been calculated by computer to locate the critical trajectories separating the entering particles I paths from those paths where the particles hit the tube wall or escape. Sampling efficiencies are presented in terms of 3 variables--a dimensionless particle size coefficient, a dimensionless orifice size coefficient and the tube orientation--for the no-wind case. Over most of the range of sampling conditions, the Stokes drag law can be used and dependence on the variable--particle Reynolds number--can be ignored. A procedure for achieving maximum efficiency in design of a sampler is proposed. Whether these results apply when typical room-sized eddies constitute the ?calm air? environment is not known.

Jan 1, 1974

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120'-0") with the upper 12 m (40'-0") to be backsloped. The vertical face of soil to be supported was 24 m (80'-0'). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987

By C. M. Harrer

The location, features, qualities, and extent of iron occurrences and the associated resources--limestone and dolomite, bentonite, coal-lignite, petroleum and natural gas, power, and water--are evaluated. The results of pioneer beneficiation tests on South Dakota taconite are discussed. In addition, pertinent features of taconite development, cost factors, the Western and Central United States trade area and markets are reported. The State's production of iron ores until 1963 has been small and for purposes other than the manufacture of iron. This investigation disclosed the probability of large resources of taconite in Pennington and Lawrence Counties. The average iron content is 29 percent, and a 65-percent or better iron concentrate might be produced. Ample resources are available for mining and processing taconite. An investment of at least $26 million would be required for a plant capable of turning out 1 million tons of agglomerated iron concentrate per year. The feasibility of such an enterprise is indicated, but intensive investigation and research must be completed to justify such an investment.

Jan 1, 1966

By Francis C. Lincoln

"INTRODUCTION As part of a general investigation of the zinc-producing area of southwestern Wisconsin, the Bureau of Mines undertook a limited amount of exploratory drilling in the immediate vicinity of the New Dale Rundell mine, in the Mifflin District of Iowa County, Wisc.The work was carried out during the early part of 1945, at a time when all effort was being directed toward increasing production of metals important to the Nation's war program. Bureau of Mines engineers decided to conduct exploration at the New Dale Rundell mine after a preliminary study of available data showed a reasonable possibility of indicating an important deposit. Before the Bureau of Mines investigation, 50 holes had been drilled in the vicinity. Of this number, 18 encountered ore of minable grade. Subsequently the mine was developed and operated for a brief period; however, work was stopped before all of the ore disclosed by drilling had been mined. There appeared to be a correlation between the ore shown by the drilling in the New Dale Rundell mine and another disclosure some 1,500 feet to the northwest. The Bureau of Mines exploration was pinned to explore this possible correlation. Of the 7 holes drilled by the Bureau of Mines, 3 disclosed minable ore beyond the limits of previous drilling."

Aug 1, 1946

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Vanessa C. Koppe

During ore body modeling normally additional samples are required to improve resources evaluation and mining planning. At this stage one rises the question about where additional samples should be located. Regular sampling pattern seems to be a reasonable choice, since all the regions within the deposit receive the same number of samples without a clear clustering. Nevertheless, values for certain attributes (grades for instance) from a mineral deposits may behave more erratic in some regions than others. Consequently, by adding samples to these regions could bring more benefit for reducing the uncertainty related to a transfer function such as Net Present Value (NPV), instead of adding samples to location of low grade uncertainty. Thus, for a given number of additional data, the test of a regular pattern and a pattern which add samples on areas of high uncertainty of the attribute of interest is worth. This paper presents an algorithm that allows the construction of these two patterns, automatically, on a software commonly used in the mining industry. The algorithm leads to a fast analysis on the efficiency of the two patterns in reducing the uncertainty associated with a transfer function.

Oct 1, 2009

Jan 1, 1996

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014

By A R. Proudman, A H. Purvis

The Granites Gold Mine Callie gold deposit is located 550 km northwest of Alice Springs in the Tanami Desert. Gold mineralisation occurs due to a complex interplay of geological factors which include but are not limited to favourable lithology, structure, alteration and quartz veining. High-grade mineralisation, while pervasive under favourable conditions, is highly variable over short distances and is very nuggetty. In contrast, the lithology and geological structures that host the mineralisation are very continuous. Orebody modelling techniques have evolved over time because of a growing understanding of the mineralisation controls. Modelling issues such as sampling and assaying accuracy, modelling method, data density, gold population statistics, geological interpretation and domaining, grade boundary and calculation conditions, and model block size are constantly being reassessed in an effort to increase understanding of the mineralisation controls and modelling accuracy. The evolution of the modelling process in response to increasing data levels and a growing understanding of the mineralisation controls has resulted in changes to the perception of the orebody size and style. This has caused the choice of underground mining method to be revised several times and the process to final mining method selection to take longer than usual. In order to achieve the planned production start-up date of July 1998 the process has been allowed to progress in parallel with development of the underground mine. This paper describes the resource modelling and mining method selection process applied to the Callie underground mine and some of the issues which have contributed to its evolution. Some conclusions that are relevant to the efficient planning and development of new mining projects in general are presented.

Jan 1, 1998

By D. Harrington

Although for many years considerable attention has been given to devising safe and efficient methods of using explosives, with some success, relatively little has been done to provide satisfactory storage facilities for them. This was known long before the present war began, but it was emphasized during the past 30 months? inspections of explosive magazines by employees of the Bureau of Mines in administration of the Federal Explosives Act of December 26, 1941. These inspections have revealed woeful in adequacy as well as definite hazards and the urgent need for obtaining better storage facilities either by remodeling old magazines or constructing ink new ones that would afford suitable protection for the contents against theft, fire, deterioration, and detonation. The purpose of this paper is to offer suggestions and to show by sketches and drawings some of the fundamental features of suitable magazines. Type of construction and available materials differ with different; localities, but the information herein contained can be applied to most magazines, whether already constructed or the construct: on of which is planned. It is hoped that this information will be helpful and will aid persons who are trying to provide suitable storage for explosives end detonators. It is also hoped that States and cities will be made aware of the unbelievable laxity practiced in storing explosives in the United States and will take some remedial action.

Jan 1, 1945

By Dean H. Ambrose

[Mining and processing earth's materials form the basic building blocks from which many technology advancements and products are made. Virtually all metallic and non- metallic products are derived from a substance found in our earth that we blend, mold, extrude, or pulverize into something useful, the mining industry is responsible for the first step of this process: extraction from the ground. Mining particularly coal mining. poses significant risks to both humans and machines. As raw materials are]

Jan 1, 2009

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982

By P. C. Thakur

The productivity in coal mines, measured in terns of the output per manshift depends largely on the efficiency and speed of men and materials transport between working faces and the surface. The mechanization of coal winning and material handling processes has led to a great rise in the mine productivity (1). Early applications of power in U. S. coal mines were mainly electrical. The excellent traction available with the DC motor and the ease of the distribution of the DC power have made trolley wire installations for haulage very popular. In shallow mines with very limited emissions of methane it did not constitute a major hazard but as mine depths increased and corresponding emissions of methane also increased fire and methane ignition hazards have become very serious. Conveyors have proved economic where intense mechanization of coal faces generates a large output of coal from a single face, but the fire and respirable dust hazard associated with them are no less serious. Recognizing these shortcomings, the Federal Coal Mine Health and Safety Act of 1969 laid down numerous provisions for the safe use of trolley-wire haulage and conveyors (2) which generally improve safety but in some cases complicate mining operations and have decreased productivity significantly since 1969. In course of time as coal mines become deeper and hence gassier and as the emphasis on safety increases it would be inconceivable to use trolley-wire haulage under ground as already witnessed in several other countries with deep coal mines. With rising capital investments and cost of the protection against fire and respirable dust, the use of conveyors may also have to be limited to special areas, e.g. main entries. Indeed, there are only two alternatives available, namely; (1) Degasify the coal seams prior to mining and use conventional electrical power, or (2) Develop alternate sources of power which would be safer and yet efficient and cheap.

Jan 1, 1975

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

This report presents production and delivered costs for coal exports from the five major Western coal-exporting countries: Australia, Canada. Colombia, South Africa, and the United States. Cost data were compiled from visits to 43 mines by U.S. Bureau of Mines engineers between 1985 and 1990. All report costs are in January 1989 U.S. dollars per short ton. Production costs for raw coal are divided into mining and regulatory categories. Costs are broken down by type of cost, type of mine. and country. Scheduled operating and capital costs for raw coal were processed by the Bureau's MINSIM discounted cash flow program to determine total production costs calculated at 0% and 15% discounted cash flow rates of return (DCFROR). Delivered costs are for salable coal delivered to various markets. Costs are broken down by supply country, market, and type of cost. Scheduled operating and capital costs for salable coal were processed by the Bureau's MINSIM discounted cash-flow program to determine total salable coal costs at 0% DCFROR. Added to total salable coal costs were transportation and port costs to get delivered costs. Comparative overview information on the coal industries of the five study countries are appended. This appendix includes information on industry economics and exports, production and reserves, and coal industry issues.

Jan 1, 1993