Search Documents

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By Gualberto Carpio

El presente texto señala la metodología desarrollada en Tintaya para la identificación de posibles proyectos, los cuales están enfocados con los objetivos del negocio y del líder del área ya que comparten metas comunes de mejoramiento. Esta mejora alcanzada con Six Sigma, solo es posible con el soporte del plan estratégico de la compañía y por ende, se hace énfasis en la correlación que existe con los proyectos a desarrollar en todas las áreas. En este sentido, el plan estratégico es alineado y controlado por indicadores clave de desempeño (KPIs) de primer, segundo y tercer nivel, los cuales indirectamente norman el desarrollo de los proyectos planteando metas de costos, incremento de producción, productividad, reducción de tiempos de ciclo, etc.

Sep 19, 2006

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

A Simulation Study on Two-Stage Grinding with High-Pressure Roller Mills By the application of high-pressure roller mill (HPRM) in the field of mineral processing, computer simulation can be used to predict overall performance of a grinding circuit based on data obtained from HPRM comminution test in pilot scale or industrial scale. Using the model developed by Klymowsky and Liu for HPRM comminution and an extended Plitt's model for classification, steady-state of a closed circuit grinding can be calculated by means of a virtual locked-cycle-test conducted on computer. This paper presents the result of a simulation study on two-stage grinding with HPRM as the comminution device. The emphasis is put on the influences of circuit-configuration and way of recirculating classifier's coarse-product on the overall circuit performance. The results show that two-stage grinding with HPRM has its merit and flexibility in meeting demands of various grinding tasks in mineral processing.

Sep 13, 2010

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By A. G. Rozner

TRANSVERSE rupture tests have been commonly used in mechanical investigations of brittle materials. The specimens are simple, easy to prepare, and loading presents no difficulty. Owing to the complexity of stress distribution in bending1 one can determine stresses rigorously only for the elastic range. The bend-test results, however, are at times converted into tensile-strength data, determined as maximum fiber stress. The assumption is made that for small plastic deformations the linear stress-strain relation applies. This problem was experimentally investigated by Bach3 who tested cast iron in bending and in tension and found that the maximum fiber strength obtained in bending exceeded the experimental tensile strength by a factor depending on the geometry of the tested piece. The factor varied from 1.57 for a rectangular cross section to 2.12 for a circular cross section of the tested beam. Since this work was carried out 60 years ago, the cast iron used could be expected to have been highly brittle, thus the extent of plastic deformation prior to fracture very small. We have therefore carried out a number of tests on magnesium-modified cast iron with an average elongation of -5 pct. It was hoped that the data obtained from the tests would serve as a guideline for comparing data obtained in tension and bending for brittle materials. Mechanical properties were measured at room temperature on an Instron tensile machine at a crosshead speed of 0.05 in. per min. The three-point bend test employed cylindrical bars 0.20 in. in diameter with a 1.0-in. span. For the tensile test, cylindrical tensile specimens with a gage length of 0.85 in. and a diameter of 0.160 in. were used. Results are summarized in Table I. From Table I one can see that fracture strength

Jan 1, 1965

By Jeremy Theys

The Sacramento Regional County Sanitation District (SRCSD) is improving the sewer system in the Natomas area of Sacramento, CA. The Upper Northwest Interceptor (UNWI) system is an ongoing series of tunnel pipeline projects that will provide sewer conveyance for all residents of northeast Sacramento County to the New Natomas Pumping Station, located North of downtown Sacramento, also in the city of Sacramento limits. The New Natomas Pumping Station then carries wastewater flowsto the Sacramento Regional Wastewater Treatment Plant in Elk Grove via the existing Lower Northwest Interceptor. The Joint Venture of Traylor Brothers, inc. and J.F. Shea (TSJV) were awarded the UNWI 1&2 project in late September, 2007. The planned 5.8 km (3.65 mile) construction route for UNWI 1&2 begins at the New Natomas Pump Station and runs north along the East Drainage Canal to the begin-ning of UNWI 3&4 at Bridgecross Drive. UNWI 1&2 includes approximately 5.8 km (19,240 feet) of 3.65 m (144 inch) inside diameter pipe using Earth Pressure Balance Tunneling Methods. The project also includes 16.76 m (55 feet) of 3.04 m (120-inch) diameter interceptor pipeline, twenty three access manholes spaced approximately 305 m (1,000 feet) apart along the alignment, a 2.13 m (84-inch) by 3.65 m (144-inch) transition structure, a 3.65 m (144-inch) by 3.04 m (120-inch) transition structure, and the connection of three existing sanitary sewer lines to the interceptor.

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

By L. A. Bakhvalov

According to the practice of mining management in the system of industrial complexes, the Kazakhstan gold mines are part of the mine processing industrial concerns providing ore-mining and ore-dressing. The cycle technology of winning operations used at the mining of vein deposits in the mines of the industrial concern is mainly provided by the systems of scrapping, scipping and electric locomotion. At present the information and computer system, elaborated on the basis of the Maikain underground mine is intended for creation of the system of automatic operation for the industrial complex mines. The information and computer system includes: - parametres characterising the accepted technology of works; - the main parametres characterising the technical devices of operation and control ; - information about the material, technical and personnel resources available at the mine; - mining and geological conditions of the deposit; - the facilities of the subsidiary units, of the mine; - the direct parametres and technico-economical indices in which the mine efficacy and activity is estimated. The suggested structure of the automatic operation system can be sensibly realized with the application of the microprocessor on the first level, the personal computer IBM PC/XT or PC/AT on the second level. For the complete realization of the project each mine will need 4-5 computers (as PC/XT), one IBM PC/AT and each mine complex - one super IBM for creation of the distributed information bank and its including in the integral world communication system.

Jan 1, 1992

By Richard H. Singleton

Greensand, which is widely distributed in the Eastern United States, was produced in 1976 only by the Inversand Co., a subsidiary of Hungerford & Terry Inc., near Clayton, N. J. Production and sales information is withheld by the Bureau of Mines. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was sold for use as a filter medium for the removal of manganese, iron, sulfide, and other elements from water.

Jan 1, 1978

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By H.A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By H. A. Bedworth

AlloTs of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry l proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche 3 and Corson. 4 The constitution of the system has also been recently investigated by Matuyama, 5 and in the laboratories of the American Brass Co. by Smith. 6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of the constitution of copper-silicon alloys, the solubility reaches its maximium value, 6.7 per cent. silicon, between 721" and '782" C. At 852" (1. the solubility is 5.25 per cent., while at 400" C. it is only 4.1 per cent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent, silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By John R. Craynon

Science and Sustainable Development Each of the ?pillars? of sustainable development are directly impacted by mining. We need science to understand exactly how mining contributes to each. Overview of presentation ? History of mining and sustainable development ? Role of stakeholders in measuring/accepting contributions of mining to SD ? Identified ?shortfalls? in understanding mining and SD ? Science needs

Aug 1, 2013

By R. L. de Beauchamp

A preliminary investigation was made of the extraction of chromium from ferrochromium by low-temperature chlorination in the 3400 to 5250 C range. The objective was to devise a method for separating chromium from iron in high-carbon ferrochromium produced from domestic chromite concentrates. The majority of iron was removed as a volatile chloride; chromium was contained in the residue as a nonvolatile chloride, which was separated from carbon and unattacked ferrochromium by dissolution. A small rotary chlorination apparatus was designed, built, and used for the chlorination tests, and samples of commercial-grade high-and low-carbon ferrochromiums were chlorinated for comparison of chlorination characteristics. Low-temperature chlorination of three types of ferrochromium resulted in the removal of 81.9 to 91.6 percent of the iron content as sublimed FeC13. Recovery of chromium in a leach solution of the reactor product varied from 82.4 to 93.1 percent.

Jan 1, 1968