Search Documents

[ ] [LOCAL SECTION CODE (Numbers indicate Sections) No. Section LI Alaska L50 Adirondack L2 Arizona L58 Arkansas L84 Balcones L66 Billings Petr. L3 Black Hills L4 Boston L76 Caracas L5 Carlsbad Potash L6 Central Appal. L60 Central N. Mex. L7 Chicago L79 CIM-AIME Calgary L82 CIM-AIME Edmonton L8 Cleveland L9 Colorado]

Jan 1, 1961

By S. F. Diehl

Suites of monomineralic sulfide and carbonate minerals, as well as mine-waste composite samples, were analyzed using chemical and microanalytical techniques to understand behavior and bioavailability of mine waste elements such as Cu, Fe, Pb, or Zn. Petrographic, scanning electron microscopy (SEM), and laser-ablation inductively-coupled mass spectrometry (LA-ICP-MS) studies of mineralogical residence sites of trace elements are important because trace elements affect the chemical and physical behavior of minerals. Leachate solutions show that chalcopyrite, bornite, azurite, malachite, and galena are host to the trace elements Ag, Al, As, Cd, Co, Cr, Mn, Ni, Pb, and Zn. SEM studies reveal whether these trace elements occur within mineral inclusions or are substituted within lattice structures. SEM analysis reveals mineral phases not identified by X-ray diffraction (XRD), such as inclusions of sphalerite and cobaltite(?) within chalcopyrite.

Jan 1, 2010

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010

By Harold L. Lovell

The extensive heterogeneity of coal is a fact long recognized by scientists and engineers. However, until recent years the practical implications of such heterogeneity have more often been realized from an undesirable experience than from knowledge or forethought. Variations in the properties of coal, even within the same seam, eventually lead to procedural modifications in mining, handling, preparation and utilization. The concepts considered here propose an enhanced application of information, detailing these properties, realizing the uniqueness of any given coal seam but the practicality of a common approach. Coal preparation practice has been designed primarily for the control of ash and sulfur content to meet market specifications which are similarly specified, Other physical characteristics of size and friability are also commonly employed and, to a lesser extent, properties which are implications of rank. The consideration of petrographic data as indicators of origin, thus total physical and chemical properties, has generally been overlooked as a realistic tool in-the exploitation of coal as a resource. The evolution of descriptive techniques, whether petrographic, physical, or chemical, capable of universal application with any rank of coal, is still beset with problems.

Jan 1, 1968

By Charles Means

A THOROUGHLY modern coal-handling system has been installed at the Pittsburgh Terminal R. R. & Coal Co.'s new No. 8 shaft, or Coverdale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur f the Montour R. R. The Pittsburgh seam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with their remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. MINE SUBSTATION The transformer substation is adjacent to a pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies.

Jan 9, 1921

By C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury; have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. TABLE 1.-Lattice Constants and Twinning Law of the Be-Cd Group of Hexagonal Metals Dimensions of Unit Axial Cell, A Ratio Description of Twinning Element a° c° (c°/a°) Composition Axis Plane Beryllium 2.28(3) 3.60(7) 1.58 {1012} Probably 1 {1012} Magnesium 3.22 5.23 1.621 ,1 {1012} Zinc 2.65(7) 4.94(8 1.86(2) 11012 } 1 {1012) Cadmium 2.98 5.63 1.88(5) {1012} Probably 1 {1012} Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2. A determination of the composition

Jan 1, 1928

By Vinicius de Oliveira Fidelis Sales

O presente trabalho tem como por objetivo a busca por uma solução eletrolítica capaz de eletropolir, eficientemente, amostras de ferro puro (>99,8% Fe). A finalidade de se utilizar o ferro é devido o interesse em suas propriedades biocompativeis e a sua possível aplicação biomédica, sendo utilizado em dispositivos biodegradáveis. Ligas à base de Fe, Mg e Zn estão ganhando importância devido às vantagens que elas oferecem, em comparação com as tradicionais (AISI316L, L605), sendo a capacidade, de se degradarem a principal caracteristica. A escolha do eletropolimento, como técnica de modificação de superfície, deve-se a sua capacidade em polir o material tornando o seu relevo mais homogêneo, garantindo um pré-tratamento adequado ao material em diversas aplicações, como por exemplo o tratamento com o plasma. Um dos grandes diferenciais desta técnica é que pode ser utilizada em materiais com geometria complexa. Foram realizados testes utilizando um grupo de 4 soluções presentes na literatura e analisados os seus efeitos em amostras de ferro puro. Com os resultados obtidos pelas análises de Microscopia Óptica, Microscópio de Força Atômica e Ângulo de Contato foi possível verificar que a solução 2C obteve o eletropolimento mais efetivo, apresentando assim as características desejadas.

Oct 30, 2017

Up to thirty years ago, coal preparation in western Canada, except at four plants, had not included actual coal washing. The exceptions were at Nanaimo and Royston, B.C., where tub washers and wet tables were in use; at Hosmer, B.C., using. Robinson cones; and at Leitch Collieries, Passburg, Alta., using a feldspar jig. The two last named collieries had a short life and were not operating in 1920. The industry was divided, as at the present day, into two sections, steam (bituminous) coal and domestic (largely sub-bituminous) coal, the first generally supplying industrial needs and the second householcl and other heating requirements. The two sections overlap to some small degree today as prepared sizes, chiefly stoker, and briquettes, from steam coal are shipped for house-hold use, and domestic slacks are used in certain industrial plants. The .domestic operator, for reasons shown later, was not primarily concerned with actual coal washing as a phase of coal preparation, and bent his efforts to improvement of screening and loading plants, with hand-picking of coarse sizes. The bituminous operator, on the other hand, felt it necessary by 1920 to consider coal washing. When the mines were comparatively young, coal quality could be controlled to a considerable degree by selective mining, by leaving behind some of the seam or by-passing districts in a mine where the coal was of inferior quality to that in other districts. This obviously had its limitations, and so the next step was coal washing.

Jan 1, 1952

By Masaru Imaizumi, Hiroyuki Nomura, Mitsuharu Takita

"Cast iron possesses many superior characteristics caused from precipitated graphite structure, for example, castability, wear resistance, solid lubrication, damping capacity. But the more graphite hyper-eutectic cast iron contains, the lower its mechanical strength becomes, because graphite gives a negative effect to strength of cast iron. In addition, primary graphite tends to segregate during solidification, so uniform materials are difficult to be produced.In this study, authors introduced semi-solid processing in developing new and high quality cast iron. A series of semi-solid processing experiments were carried out to clarify the effect of stirring condition; solidification temperature and etc. on microstructures and characteristics of cast iron. In particular much attention is paid to the appearance of ternary eutectic zone at the final stage of solidification. As the results advanced hyper-eutectic cast iron was obtained with high quality of both the mechanical strength and wear resistance. As for the mechanical strength, 300MPa and 0.60% are obtained as the tensile strength and the elongation values, respectively, under the controlled stirring condition. This indicates that semi-solid processed hyper-eutectic cast iron is used prospectively without spheroidization.IntroductionCast iron has various good properties such as wear resistance, solid lubrication, damping capacity and machinability. The characteristics of cast iron are mainly decided by graphite structure, namely graphite shape and its distribution in the matrix. Mechanical strength of cast iron is large in the case of small quantity of graphite particles which are precipitated uniformly, however, it becomes small in the case of large quantity of graphite precipitated flakily."

Jan 1, 2000

By Luciana Lezira Pereira de Almeida

De forma geral, as ferramentas diamantadas empregadas no corte de rochas ornamentais são compósitos constituídos de partículas de diamante embebidas em uma matriz metálica. Neste trabalho, para a preparação da mistura das pós, foram utilizados dois processos distintos: o processo convencional utilizando um misturador do tipo cônico e um processo alternativo utilizando um moinho do tipo Attritor. Ambos os processos tiveram a duração de uma hora. Após o processo de mistura, os pós foram sinterizados sob as mesmas condições, pressão de 35MPa e Temperatura de 750oC por um período de 6 mim. Foram produzidos corpos de prova com e sem diamantes. Para a caracterização dos compósitos foi utilizada a Microscopia Eletrônica de Varredura (MEV), Difração de Raios X (DRX), Porosimetria e ensaio de desgaste. Após as caracterizações e testes ficou evidente que os compósitos obtidos a partir da mistura utilizando o moinho Attitor exibiram melhores propriedades, inclusive em relação à compósitos industriais.

Aug 16, 2017

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa May, '71.. 1 3 2. Bethlehem, I's Aug., '71.. 110 3. Troy, N. Y Nov., '71.. 113 4. Philadelphia, PaFeb., '72.. 117 5. New York, N. YMay, '72120 6. Pittsburgh, Pa Oct., '72.. 125 7. Boston, MassFeb., '73.. 128 8. Philadelphia, Pa.*May, '73.. 23 9. Easton, PaOct., '73.. 27 10. New York, N. Y Feb., '74211] [ ]

Jan 1, 1925

By John Durkin, Roy J. Greenfield

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the signal amplitude as a function of source type, source depth, and horizontal off- set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the sys- tem, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will he detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

Methods for ore reserve estimation are classified. The amount of information needed to asses ore reserves is analysed. Reference is made to gold sampling. Consideration is given to nugget effects and ore reserve estimation procedures where they are significant. Computer methods are discussed

Jan 1, 1997

By D. W. Bacon

Plant process optimization programs are often costly, both in technical effort and loss of production. Evolutionary Operation or "EVOP" is a mode of plant operation consisting of controlled cyclical changes in process conditions by which information is provided concerning potential process improvements while both volume and quality uniformity in production are maintained. Its conceptual simplicity and low cost of utilization have led to successful adoption in a variety of industrial manufacturing operations. This paper is an expository account of basic EVOP theory, the problems encountered and the organization required in applying it to a processing plant. Illustrations are provided which indicate the payoff that can result.

Jan 1, 1967

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mine Superintendent or Manager. Age 34, graduate mining engineer. Thirteen years' practical mining experience in Canada and United States holding responsible executive positions, mining engineer and mine superintendent. Experience in iron, gold, copper, and pyrite mining. Best references, can go anywhere but prefer location in Canada. At present engaged but desire change. Minimum salary $3600. A-2845. Manager or Superintendent for producing mine or new development. Institute member, 25 years' experience, mining, wet concentration, construction and examination. A-1173. Mining and Metallurgical Engineer. Technical graduate, 11 years' practical experience principally with copper mining, milling, smelting, and electrolytic refining, now holding an engineering executive position, wishes to change to place of more responsibility and opportunity. A-3785. Engineer with 11 years' experience in mining, civil, and industrial engineering, desires to become connected with a strong organization requiring services of thoroughly trained man. Graduated from University in 1909, now employed, having been with present organization nearly 7 years. Available about Sept. 15. A-4071. Metallurgical Engineer, age 31, married, A. M. and Ch. E.; 7 years' teaching and industrial experience, of which 3 ½ have been with electric furnaces. Desires position in investigative or executive work. Minimum salary $3000. A-4176.

Jan 9, 1919

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By Charles Will Wright

Brief descriptions of the occurrence of the various deposits of strategic minerals then known in South America are published in "The Mineral Deposits of South America," by B. L. Miller and J. T. Singewald, 1919; in "Ores and Industry in South America," by H. F. Bain and T. T. Read, 1934; and in many publications on the individual countries. To give a gen.era1 idea of the situation today and possibilities for future output of strategic minerals in several of the countries, the following notes are offered. All tonnages are in metric units.

Jan 1, 1940