Search Documents

By Michel Dagbert

With the growing demand for energy, explora¬tion for uranium deposits has dramatically increased in the past few years. Since the early ages of uranium exploration, natural gamma ray logs has proved fast and convenient in locating and evaluating mineralized bodies. However, natural gamma ray logging is an indirect measure of the uranium content and in some circonstances, the radiometric signal can be 'altered in a very significant way. To check the presence of any distortion, statistical comparision of radiometric counts and chemical assay values for the same samples is generally performed. Of course in such studies, one inevitably mixes samples where the radiometric signal is really proportional to the uranium content and samples where this signal is influenced by many other sources or distorted before being recorded. Nevertheless, the average tendency leads to correction factors which are then applied to every radiometric reading in the deposit or portion of the deposit where the statistical comparison is made. To account for the "average" character of these correction factors, a parameter of uncertainty like a standard deviation of possible errors is associated to each corrected value. This parameter can be latter used in an ore reserve estimation when the weights assigned to samples should depend on the precision of their grade. The purpose of this paper is to present a new regression technique which can be used without any restrictive hypothesis like a normal or lognormal distribution. Different standard ways which can be used to statistically compare radiometric and chemical assay values for the same sample and to derive a correction factor for the latter will first be reviewed, after a general discussion of disequilibrium problems. The discussion and the examples will be restricted to the case of natural gamma ray logging in drill holes but the methods presented in this paper can also be applied to data from the radiometric probing of a working face or a truck load in an operating mine.

Jan 1, 1979

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

Jan 1, 1904

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

The following list comprises the names of those persons who became members during the period May 10, 1916, to June 10, 1916: ARCHIBALD, JOHN CHRISTIE, Min. Engr., Supt. of Cyanide Plant, Guanajuato Reduction Mines, Guanajuato, Mex. BRUNEL, FRANK P., Cons. Min. Engr Mitchell & Brunel, Ajo, Ariz. CALVERT, WILLIAM ROBERT, Cons. Geol. ...225 Kearns Bldg., Salt Lake City, Utah. CHAMPION, J. R., Supt The Yak Mining, Milling & Tunnel Co., Leadville, Colo. CHARLES, LAVERN JOHN, Construction Engr., Elephant Butte Dam, Elephant Butte, N. M. CHASTEL, ANDRE, Min. Engr., Societe Miniere & Metallurgique de Penarroya, 12, Place Vendome, Paris, France. CHRISTIE, WALLACE H., Vice-Pres. and Mgr., Alt. Bert Gold Dredging Co., 604 Mission St., San Francisco, Cal. CLARK, RONALD ..Hardinge Conical Mill Co., 120 Broadway, New York, N. Y.

Jan 7, 1916

By Robert S. Baker

It has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformiation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta) (alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It, is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850" C. in iced brine at -8" C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 35.60 per cent zinc (9812 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1932

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced' by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

INTRODUCTION Data available on prophyry copper occurrences in the Andean, Caribbean, Appalachian, and Cordilleran orogens may be categorized in a manner to suggest a hypothetical evolution for deposits that occur in the western hemisphere. A classification of de- posits is also suggested. A classification dependent on internal structure of a porphyry copper deposit would lead to two broad categories, breccia pipe and stockwork models. A classification of this type is examined herein but it is not universally accepted in the literature. Modeling based on igneous petrography as well as metasomatism attendant with the sulfide mineralization is more widely accepted by economic geologists whose evaluation of porphyry systems is influenced by the presence or absence of a phyllic zone. Lowell and Guilbert model deposits ordinarily include a phyllic zone, whereas those of the diorite model do not. Position of the phyllic zone in the alteration sequence is a significant ore guide. Should the phyllic zone be absent, dependence on alteration zoning to identify metallization is weakened. Presence or absence of the phyllic zone therefore is a significant parameter in the economic evaluation of a porphyry copper deposit (Hollister. et al., 1975). The Lowell and Guilbert (1970) model commonly includes a phyllic zone in quartz- bearing rocks. Parameters of both calc-alkalic and the quartz monzonite models mentioned elsewhere in this volume are sufficiently close to the Lowell and Guilbert (1970) model that it should be expanded to encompass them. The diorite model remains separate and distinct because deposits of this type are characterized by an absence of quartz in the pluton, commonly highly gold: copper ratios, low molybdenum content, and regular absence of sericite in the alteration zones. Therefore, for the benefit of those

Jan 1, 1978

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By Hagen B. Schultes

"Refratechnik, a leading German refractory company, acquired a majority shareholding in Baymag in 1979. This acquisition included the mining rights for a magnesite deposit of exceptionally high purity in the Canadian Rocky Mountains.The deposit, situated in the Kootenay region of southeastern British Columbia, is of Cambrian age and has ore reserves of 50 million m. t. of magnesite. The Baymag magnesite deposit is one of the purest in the world. The deposit was opened up and mining commenced in early 1982. Production of various caustic calcined magnesia products in a rotary kiln operation in Exshaw, Alberta, was started in mid-1982. The product application ranges from pulp and paper production, to the chemical industry, and to animal feed supplements. Since the end of 1983, Baymag has produced high-quality refractory grade fused magnesium oxide f or specialty applications in the steel industry.IntroductionAlthough magnesium is the eighth most abundant element in the earth and forms about 2.06% of the earth's crust, common knowledge about magnesium and especially magnesium oxide (MgO) as an industrial mineral is not widespread. The reason might be that, with the exception of magnesium metal as the element, magnesia products are not generally sold as final products to end-users, but rather are needed for the production of final products such as steel, cement, paper, etc. Therefore, some general comments are given about the different sources of MgO, the different products, world production and consumption , before Baymag specifics are addressed. Magnesium metal will not be discussed in this paper."

Jan 1, 1986

By R. W. Gurry

In a series of charts this paper presents the composition of all gas mixtures, composed of the elements carbon, hydrogen, oxygen and nitrogen, which at temperatures from 1000° to 1800°F are in equilibrium with (1) austenite of various carbon contents, (2) iron and iron carbide, (3) graphite, (4) iron and its oxide. THIS paper presents the results of calculations made to determine the proportions of CO, CO2, CH4, H2, H2O and N2 in gas mixtures which, at temperatures from 1000" to 1800°F, satisfy, individually, the following conditions: (1) equilibrium with carbon steel of specified carbon content throughout the stable 7 iron region; (2) equilibrium with iron and iron carbide, both above and below the eutectoid temperature; (3) equilibrium with graphite; (4) equilibrium with iron and its oxide. From these data a new type of chart has been prepared which permits one to determine, from a room-temperature analysis of the furnace gas in question, the effect of the gas upon the steel at furnace temperature. Thus a guide is provided as to the carbon content which will result and as to the possibility of oxidation or sooting. All of the atmospheres commonly used in the commercial heat treatment of steel are composed of some or all of the simple constituents CO, CO2, CH4, H2, H2O and N2, and also in some cases oxygen or higher hydrocarbons. As the gas mixture is heated certain alterations in the proportions of the constituents take place, and at the temperature of the furnace the composition is, in general, not at all that of the entering gas. If equilibrium in the gas phase is presumed a calculation involving the use of certain fundamental data predicts for a certain temperature the carburizing, decarburizing, or sooting characteristics of a given atmosphere, and, upon the additional assumption of equilibrium between gas and metal, also the oxidizing ability of the gas and the ultimate carbon content of the steel. The extent to which these predictions are fulfilled will depend upon how closely the assumptions of equilibrium are realized in any particular case. Although at lower temperatures equilibrium is often not reached, there is considerable evidence indicating that above about 1000°F the approach to equilibrium in the gas phase is generally substantially complete, particularly in the vicinity of the steel which acts as a powerful catalyst in promoting reactions in the gas phase. The extent of the gas-metal reactions is commonly affected essentially by the sojourn at temperature; equilibrium with respect to carbon, for example, is accomplished simply by continuing the treatment long enough. However close the approximation of equilibrium may be in any instance, the above mentioned calculation indicates the condition of the steel at equilibrium, and at the present time this is the only basis of control of a furnace atmosphere. The effect at elevated temperature of a gas of a certain composition at room temperature upon a given steel has customarily been judged by first calculating from gas equilibrium constants the proportions of the gas constituents at the temperature of the steel, then comparing certain of these with the proportions known to be in carbon or oxygen equilibrium. This process is tedious and time-consuming, in particular because the calculation generally involves a series of successive approximations; and since some knowledge and familiarity with this type of computation are required, not everyone needing the information has been, in the past, in a position to obtain it. By making a series of equilibrium calculations, combining with fundamental data for gas-metal reactions, and plotting the results in a special way, a chart has been prepared which enables anyone

Jan 1, 1951

By Z Li, D Chalmers, J M. Tenney

This paper presents the findings and analysis of the investigation of effectiveness of thin spray-on liners (TSLs) as a gas management tool in underground coalmines. The project involves spraying TSL on the area surrounding gas drainage holes whereby the TSL acts as a thin membrane decreasing the permeability of the coal. This restricts air migrating through the coal seam and diluting gas from the drainage holes. There are a number of potential benefits from this technique but key points are that gas drainage holes produce gas with higher concentrations of methane. The design and execution of a field trial to investigate the effectiveness of a TSL on purity of in situ methane from gas drainage holes is presented in this report. For eight drainage holes, the results show an average increase in methane purity by 9.14 per cent and a reduction in air contamination by an average 7.93 per cent. Overall methane flow rate decreased by 27.6 L/s; however, flow rates were unreliable due to poor measuring equipment. For most holes, methane purity was not changed significantly; however, certain boreholes were responsible for most of the variation in methane purity. The boreholes showing a dramatic improvement in methane purity were likely those with intersecting cleats covered by the TSL. If the TSL was sprayed over more area, specifically in areas where the cleats are intersecting with holes, it is likely that purity of methane in the drainage holes will increase.CITATION:Tenney, J M, Chalmers, D and Li, Z, 2015. Thin spray-on liners potential in reducing dilution of in situ gas in underground coalmines, in Proceedings The Australian Mine Ventilation Conference, pp 323–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A. L. Holley

The first session was held in the rooms of the American Philosophical Society, on Tuesday evening, February 26th. The President, Dr. T. Sterry Hunt, called the meeting to order, and after a few introductory remarks concerning the importance of theoretical and speculative science, which often involves principles of the highest economic value, and, more than all that, serves to enlarge our conceptions of the universe, and ennoble us, by the cultivation which it affords to our most exalted faculties, proceeded to discuss some points in the chemistry of the atmosphere. It is known that there is in the crust of the earth a great amount of oxidized carbon, not only in the shape of coal, but also in the graphite or plunlbago of the crystalline rocks, in the various bituminous shales or pyroschists, which are found in all succeeding rock-formations, and also in the forms of bitumen and petroleum. All the analogies of nature lead us to conclude that these various carbonaceous substances have had an organic origin, and have been generated by the deoxidation of carbonic acid, a process effected by the growing plant, and attended with the liberation of oxygen. He showed that the carbon of a layer of coal covering the whole earth's surface to the thickness of one meter, would, in its production from carbonic dioxide, liberate an amount of oxygen equal to that now present in our atmosphere. But bituminous coal contains also a large amount of hydrogen, derived from the deoxidation of water, which implies the liberation of a farther portion of oxygen. The amount from this latter source would equal, for the various coals and asphalts, from one-eighth to one-fourth, and, for the petroleums, onehalf of that set free in the deoxidation of the carbon which these hydrocarbonaceous bodies contain. From what we know of the composition of the stratified rocks, it is probable that they include an amount of deoxidized carbon and hydrogen many times greater than that contained in a layer of coal one meter in thickness, and, consequently, that the disengaged oxygen in past ages must have far exceeded that now present in our atmosphere. To this must be added

Jan 1, 1879

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By G. Diáz

A basic technology coping with a wide range of secondary zinc sources has been developed. The process combines an electrowinning stage, a solvent-extraction unit and a leaching procedure. The acidity generated in zinc electrowinning, transferred by the organic solvent to the aqueous raffinate, is reused to leach the zinc secondary materials. The basic process recovering zinc is described in detail. The route recovering other valuable metals such as copper, cadmium and lead associated with zinc is also described. This non-ferrous metals recovery route is advisable for either ecological and/or economical reasons. Main results of an experimental program aiming at the demonstration of the suitability of the process for several feed materials are summarized. Waelz oxides, galvanizing ashes and EAFD coming from different sources were tested in laboratory and continuous pilot plant campaigns. High zinc recovery, low reagents and utilities consumption, and effluents meeting environmental regulation were confirmed. The paper also includes the main results of a feasibility study of an industrial "base case". A mixed raw material and Spanish EAFD and 20,000 ta of zinc ingots production were chosen. The SGH zinc recovery from secondary raw material by means of the clean, safe and profitable Modified Zincex Process has been demonstrated. This reliable technology is ready for industrial application.

Jan 1, 1995

By A Suwandhi, H Utama

PT. Indo Muro Kencana (PT.IMK) is a gold mine that is located in Central Kalimantan, Indonesia. Drilling and blasting activity is applied in order to support mining production. Drilling and Blasting (D&B) planning is conducted by its engineers. A drilling and blasting contractor conducts drilling and blasting activity. The objective of this paper is to evaluate the implementation of the scaled depth of burial (Chiappetta and Treleven, 1997) in explosive charging sheet application to increase blast efficiency. The function of the scaled depth of burial is to maintain stemming height above explosive charge in order to prevent the ‘over energy’ condition, to reduce the excessive fly rock possibility, to maintain rock fragmentation (digger’s productivity) and to increase blast efficiency. The focus of this paper is to implement the scaled depth of burial as a reference in D&B planning and practice, especially in designing stemming height. The purpose of this paper is to validate that the scaled depth of burial can be used as an engineering tool in D&B practice in PT.IMK. However, scaled depth of burial cannot applied as an engineering tool to determine stemming height above explosive charge for trim blastholes and secondary blasting area. In general, the implementation of the scaled depth of burial in PT.IMK is applicable for production blastholes (ore and waste blasting). In conclusion, it is clear that scaled depth of burial can be used as an engineering tool to create explosive charging sheet and also to increase blast efficiency (ore and waste blasting) in PT.IMK.

Jun 22, 2022

By Ronaldo Santos Sampaio

This paper call attention to increasing ratio of oxygen depletion from atmosphere besides the global worries about CO2 concentration increase in the atmosphere. It highlights the big mistake in considering Carbon Capture and Storage, CCS, as a way to reduce the increasing concentration of CO2 in the atmosphere. As a hypothetical example it presents an existing pseudo-ecosystem of manufacturing that has real windows of opportunity to increase its share in the global materials production industry, even in highly industrialized countries. As a suggestion and example the author point out possibilities to almost fulfill the proposed simple rules to be considered inside an ecosystem of manufacturing utilizing the production of steel via biomass versus fossil coal. A relevant and difficult rule to be attained in a quasi-ecosystem of manufacture is to be a near zero atmosphere oxygen depletion integrated process. The industrial alternatives that utilizes the actual photosynthesis are the ones that can reach a higher ecosystem of manufacture’s index. It is presented an ideal integrated steelmaking process where the gaseous, liquids and solid residues generated in one part of the system are or can be utilized in the other parts of the same system. A potential ecosystem of manufacture to produce primary iron is illustrated in the paper.

Aug 17, 2017

By V. J. Hucka, J. H. Tu

"A computer model has been developed for evaluating the performance of truck and shovel operations in an open-pit mine. The data required for describing the haulage network are simplified and shift startup and ending procedures specific to any given mine can be incorporated into the model readily . The model uses a FORTRAN-based simulation language SLAM and can be tailored to the conditions and practices of a particular mine.The model is used to analyze truck and shovel operations, evaluate different haulage layouts in the planning stage, or compare the expected performance of alternative truck dispatching systems.Stochastic simulation is used to model the random variation in time required f or the individual activities. This gives a more realistic representation of the processes under study. Simulation runs show good agreement with actual performance. The model is especially useful for examining alternatives in equipment acquisition , haulroad design, truck-shovel allocation and dispatching methods. The results of such simulations provide a sound basis f or making major management decisions.IntroductionTruck haul age is widely used in open-pit mining operations. It is also the largest cost item in the operating costs of an openpit mine, in some cases accounting for an estimated 50% of operating costs(1) , Truck replacements, which are necessary from time to time, involve large amounts of cap ital. Increasing depth of mining and consequent increase in stripping ratios require additional capital investment in the truck-shovel fleet. The sharp rise in energy costs over the last decade has also contibuted significantly to an increase in truck fleet operating costs . All these factors have led mine operators to search for ways to improve the effectiveness of the truck-shovel fleet, in order to lower costs and maintain a profitable operation in the face of declining markets and increasing world wide competition.Control of truck haulage in an open-pit mine is usually done in one of two ways."

Jan 1, 1985

By K. A. Natarajan, S. Usha Padukone

"An industrial waste liquor having high sulfate concentrations was subjected to biological treatment using the sulfate-reducing bacteria (SRB) Desulfovibrio desulfuricans. Toxicity levels of different sulfate, cobalt and nickel concentrations toward growth of the SRB with respect to biological sulfate reduction kinetics was initially established. Optimum sulfate concentration to promote SRB growth amounted to 0.8 - 1 g/L. The strain of D. desulfuricans used in this study initially tolerated up to 4 -5 g/L of sulfate or 50 mg/L of cobalt and nickel, while its tolerance could be further enhanced through adaptation by serial subculturing in the presence of increasing concentrations of sulfate, cobalt and nickel. From the waste liquor, more than 70% of sulfate and 95% of cobalt and nickel could be precipitated as sulfides, using a preadapted strain of D. desulfuricans. Probable mechanisms involving biological sulfide precipitation and metal adsorption onto precipitates and bacterial cells are discussed.IntroductionIndustrial effluents from hydrometallurgical and mineral processing operations often contain high sulfate and metal concentrations posing significant disposal problems, which require urgent solution to avoid serious environmental contamination. In such waste liquors, sulfate and heavy metals such as cobalt, nickel, zinc and iron originate from the chemical or biological oxidation of exposed sulfide minerals. Reduction of sulfate and precipitation of toxic metal ions from industrial wastes is essential from the viewpoint of environmentally acceptable waste disposal and recovery of associated strategic metals.Many of these heavy metals are essential for metabolic activity of bacterial cells at low levels. But they exert toxic effects at concentrations encountered in polluted water. Removal of toxic metals through biological reduction of sulfates from industrial waste waters have been practiced for several decades. Metal remediation through common physicochemical techniques such as oxidation-reduction, chemical precipitation, filtration, electrochemical treatment, evaporation, ion exchange and reverse osmosis processes is expensive and not suitable in the case of voluminous effluents containing complexing organic matter and low metal concentrations. Further, strong and contaminating reagents are used for desorption, resulting in toxic sludge and secondary environmental pollution. Biotechnological approaches can be more efficient and cost effective for detoxification of such effluents. Biotreatment/ bioremoval offers several advantages over conventional chemical and physical treatment technologies, especially for diluted and mixed contaminants. Biological detoxification, which involves the use of microbes to detoxify and degrade environmental contaminants, has received increasing attention in recent years (Iwamoto and Nasu, 2001). In addition, valuable metals can be recovered from metal sulfide sludge (Boonstra et al., 1999)."

Jan 1, 2015

By Lucas de A. Pontes, Lázaro A. Rohen, F. V. Carlos Maurício, Janaina da Silva Vieira, Sergio Monteiro, Dhyemila de P. Mantovani, Frederico M. Margem, Anna C. C. Neves

The lower density of the lignocellulosic fibers such as the hemp fibers and the other natural ones is one of the characteristics that allow the scientists to obtain high levels of specific properties that when compared to the properties of ordinary reinforcements gives to the hemp fibers an advantage as a material with an expressive potential in the mechanical properties area. Then, the aim of this present work is to characterize the relative density of the hemp fiber related to the water using the pycnometry technique. This technique uses the pycnometer and it is divided in two steps. In the first step the correction factor and the moisture content of the fresh hemp fiber specimen and in the other step some weightings were done such as the dry specimen (g), empty pycnometer (g), pycnometer + water (g) and pycnometer + water + specimen (g) using a digital balance with a precision scale of 0.001 g of the bran INNERSCAN. Based on these measurement and calculations using some formulations already established in previous studies, the relative density of the hemp fiber found was around 1.393 g/cm3 and the moisture content around 7.1%.

Mar 1, 2017