Search Documents

By Antti Roine

Sulfidic zinc concentrates are usually roasted in a fluidized bed furnace into sulfur-free oxide form. Metallic zinc is produced from this oxidic calcine using hydrometallurgical leaching, solution purification and electrowinning stages. The roasting step is necessary because zinc oxides are easier to dissolve using traditional leaching methods than zinc sulfides. The Kokkola Zinc smelter uses various types of zinc concentrates and secondary materials as feed mixture. This makes it difficult to find optimum process parameters for the roaster when the composition and particle size distribution of the feed mixture varies even on a daily basis. Certain conditions may even cause difficult accretion problems or increase the amount of calcine in the process off-gas line excessively. A thermochemical heat and material balance model was developed for process advisor, in order to estimate the effects of different process parameters (temperature, process air coefficient, concentrate feed, oxygen enrichment, water feed, etc.) on the heat balance, roasting temperature and calcine composition. This model was constructed using the heat balance module of HSC Chemistry 4.0 software. The prevailing chemical compounds in the concentrate and calcine were verified using mineralogical analyses and equilibrium calculations. The roasting process seems to operate near chemical equilibrium conditions, if the behavior of the main components is considered. This paper describes briefly the basic principles of the calculation model and outlines the results with several diagrams and discussion. The calculated results were in reasonable agreement with the recent process air oxygen enrichment and water feed test campaigns carried out at Kokkola in 1999.

Jan 1, 2000

LIST OF MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES ALPHABETICALLY ARRANGED ||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Seience Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbort, A N , Mines Supt , Mazapil Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexieo '23 Abbott, Clarence E , Gen'l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4812 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburg, Kans '20 Abey, Hiroshi, Min & Met Engr. Takata & Co, 2 Yeirakucho, Niehome, Kolimachi-ku, Tokyo, Japan '17 ||Aborn, Robert H 24 Groveland St, Auburndale, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cario, Egypt '17 Abraham, Arthur W 1828 N Alexandria Ave, Los Angeles, Cal '20 Abrahams, A. I 115 East 82nd St. New York, N Y '14 ||Abrahamson, C. Walter, Min Engr, Brule Min Co Stambaugh, Mich '21 Abrams, Charles Jackson Columbia Bldg, Spokane, Wash '21 Abrams, David H, Min Engr, S E Dickey & Co, 809-11 Johnstown Trust Bldg, Johnstown, Pa '20 Acker, E 01C, Met 128 East Washington Lane, Germantown, Philadelphia, Pa '86 Acker, William L, Diamond Drill Contractor Mears Bldg, Scranton, Pa '18 Ackerman, Ernest R, Pres Lawrenee Portland Cement Co Plainfield, Union Co, N J '15 Adachi, Jinzoo 11 Shiba Park, Shiba-Ku, Tokyo, Japan '88 Adachi, Yuich, Meeh Engr, Anzan Steel Works, Anzan, South Manchuria, China, (Via Dairen) '21

Jan 1, 1923

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

By T. W. Wlodek, Zygmunt Kowalczyk

In the period from 1946 to 1964, the annual output of co al from Polish mines increased from 4 7.3 to 117.35 million tons. In this paper, the methods of bringing about this increase in productivity through the building of some twelve new collieries (producing some 15 million tons annually) and the modernization, reconstruction and extension of some thirty-six older collieries are discussed.

Jan 1, 1967

By C. W. Pollock

THAT a distressing explosion of some magnitude did not take place in the Berry No. 3 mine of the Ford Collieries Co. recently was solely because no source of ignition was present when the stage was set for such an occurrence. The mines of this company, which are in West Deer Township, Allegheny' County, Pa., have been operating in the double or thick Freeport seam since 1.909. During this entire period they have been classed as gaseous by the Pennsylvania Department of Mines, and some gas has been encountered from time to time almost entirely however in development work in the vicinity of clay veins or wants-and never to my knowledge on gobs or in rib work.

Jan 1, 1935

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By E. L. Rawlins

A previous report4 has explained that pipe lines for the transmission of natural gas should be buried to minimize temperature fluctuations because when excessive the latter decrease accuracy in measuring gas volume and increase leakage of gas due to expansion and contraction in the pipe joints. These effects are governed by the rapidity of the temperature fluctuations and by the total variation over a period of time. The temperature of gas flowing through a pipe line depends to a large extent, upon the temperature of the ground adjacent to the pipe; hence, fluctuation of the ground temperatures at various depths determines the economic depth at which pipe lines should be buried. Scope and Purpose of Report This report covers a record of the daily atmospheric temperature fluctuations at Bartlesville, Okla., for 12 months and a-similar concurrent record of the temperature variation 1, 2, 3, and 4 feet below the surface of the ground.

Jan 1, 1928

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947

By C. Musingwini

The South African mining industry continues to be a major source of employment at a time when at least 25 per cent of the working age population is unemployed. At the same time the industry faces a skills shortage in many of the disciplines necessary for its future health. The University of the Witwatersrand, University of Pretoria, University of Johannesburg, and University of South Africa have historically produced mining graduates for the South African industry, with any shortfall being met by the recruitment of overseas graduates. More recently the global shortage of engineers and other mining industry professionals has seen a reversal of this trend and a very significant emigration of well-educated and highly skilled personnel. The traditional career path for mining graduates is in production and mine management. However, there is the parallel and possibly more pressing need for specialized skills in such fields as ventilation, rock engineering, mine planning, mineral resource evaluation, and mineral asset valuation. It is in these essential areas that chronic shortages continue to hamper the development of the industry and may well frustrate its ambitions to be safe, healthy, and profitable into the future. The permeability of skills across sectorial boundaries within the mining industry requires that skills shortages in the platinum sector are not looked at in isolation, but within the context of the entire industry. This paper reviews the efforts being made by the universities at both undergraduate and postgraduate levels to meet the needs of the South African mining industry, in terms of the required numbers and the range of specialized skills.

Jan 1, 2012

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By J. P. Murphy, T. E. Leontis

DURING the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,1 in his treatise on-magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 200 to 300°C. (68° to 572°F.) and the results of Vosskühler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Keil2 have also reported the creep properties of a forged magnesium-cerium-manganese alloy at 200° and 250°C. (392° and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554°F.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 percent Mn have been found on the German .BMW-801D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both .the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per, cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at elevated temperatures. The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The

Jan 1, 1946

By J E. Wheeler, S B. Valine, L G. Albuquerque

It has long been known that closed circuit grinding with a classifier improves grinding efficiency, reduces unit specific power consumption, and reduces over grinding. The classification device removes material from the circuit that has reached the desired size and returns coarse material back to the mill for further grinding. The efficiency of the classifier is an important factor in the overall performance of a grinding circuit. The classifier affects the capacity of the grinding circuit and the metallurgical performance of downstream operations. A review of historical research and modern case studies is used to demonstrate the benefits of high frequency screens for classification in grinding circuits.CITATION:Valine, S B, Wheeler, J E and Albuquerque, L G, 2012. Applications of fine screens in grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 389-394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K. Bullock, M. Levesque, G. Lyle, D. L. Millar

ABSTRACT The options for reducing the carbon footprint of energy use in mining fall into three categories of activity: i) reducing demand, ii) improving energy utilization, and iii) adopting low carbon energy technologies. In addition to the environmental imperative, the economic case for these activities gains higher priority as the prices of electricity, gas, and liquid fuels increase. Low-carbon, energy-saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital-intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as new mineral property developments. For energy services companies that specialize in the financing, construction, efficient operation, and maintenance of energy projects, the same returns and payback periods can be considered acceptable or even attractive.

Jan 1, 2012

By Marco Rojas

El yacimiento de Cerro Lindo es un depósito de sulfuros masivos de naturaleza volcánica, cuyo método de explotación Sub Level Stoping fue el más adecuado dado que utilizaba taladros largos en abanico que oscilaban entre los 8.0 y 21.0 metros; y posteriormente se convirtieron en taladros pasantes de hasta 38.0 metros. Sin embargo, existe un descontrol en la estabilidad de la roca remante, ubicado entre ambos lados de la galería central superior del tajo,y que tiene como consecuencia el colapso de la misma. En ese sentido, el presente texto plantea una alternativa de solución a través de la ejecución de taladros entre las mallas y paralelos a los últimos taladros de cada abanico, donde se calcula su espaciamiento y se les da la forma para generar voladura controlada. De forma que se determina los parámetros necesarios para ejecutar una voladura controlada exitosa que mantiene un mejor desarrollo de los tajos en Cerro Lindo.

Oct 21, 2015

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971

By Harry R. Nicholls

Preliminary tests on presplitting rock in the presence of an in situ static stress field were undertaken to study the influence of a horizontal static stress field on the creation of a vertical presplit fracture plane. These tests indicated that it is easier to fracture the rock parallel to the in situ maximum compressive stress than in other directions. Instrumented shots indicate that the interaction of stress waves generated by the detonating charges is probably responsible for starting tensile fractures between shotholes and that expanding gases may propagate these initial cracks by a wedging action. The hole spacing for presplitting appears to be equal to the half wavelength of the stress wave. However, wider hole spacing appears feasible if the initial fracture is started by closer hole spacing.

Jan 1, 1966

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996