Search Documents

By John Newby, Edward Kennedy, Ulf Gwildis

Alluvial deposits of major rivers often provide relatively uniform tunneling conditions. However, these conditions pose specific challenges due to the tunneling behavior of the granular soils as flowing ground, if unsupported. This paper describes the design considerations and construction experiences gained during the Tunnel Boring Machine (TBM) drives for the Annacis Island WWTP New Outfall System in the Vancouver, B.C. metropolitan area. Meeting the design criteria for connecting two (2) deep on-land shafts with an in-river riser manifold required advancing a 5-meter-diameter slurry TBM through the Fraser Rivers sands and at a tunnel invert elevation with a baseline hydrostatic head of 3.4 bar.

Dec 1, 2022

By E. Dernedde

A few studies have suggested that the rate of adsorption of hydrogen fluoride on smelter grade alumina is determined by kinetic factors. However, no performance equation for dry scrubbers has appeared in the literature so far. Experimental data from a pilot dry scrubber with co-current flow were compared with results of kinetic models of adsorption, film diffusion and pore diffusion. The pore diffusion model was deemed the most appropriate. It was transformed into a performance equation for steady-state operations of dry scrubbers by the inclusion of the alumina recirculation. Operating results of industrial dry scrubbers with co-current flow were successfully evaluated by means of the performance equation. The average fluoride content of the alumina was also estimated by using the pore diffusion model.

Jan 1, 2011

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

By Abhakumari

Effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. Effect of the magnitude of electrolytic currents on the activity and growth of bacterial cells was studied. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and bio catalysis of anodic oxidation.

Sep 1, 2012

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By K. Y. Haramy

This report describes the development of an equation for predicting the crushing strength of 2-inch (5.08-cm) cubes of coal from point load tests made on irregular lumps. The equation was developed from point load and cube crushing strength tests performed on coal samples from six Western U.S. coal seams. For the six coals tested, the means of the point loads [(P)] in kg at failure were approximately proportional to the deans it the distances [(V)], in cm between the platen points for lumps in the 2 to 10-cm size ramie. This finding is at variance with results of tests on other rock types reported in the literature, which tend to show that P is proportional to D2 , as is normally assumed (in theoretical grounds. [The average crushing strength of a 2-inch (5.08 cu) cane for each type of coal was plotted against the log 10 of the slope of the P vs D plots, AP/AID . A straight line was fitted to these plots. The equation of the fitted line is cr = 1.72 x 10 4 10gK -2.10 x 10 4, where Cr is re estimated 2-inch (5. 08-cu,) cube crushing strength of the coal in psi and K is the scope of the straight line fitted to a plat of P v D for the same coal.]

Jan 1, 1982

By D. Bergekoff

IN the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

By Victor E. Kral

"INTRODUCTION The Phelps Stokes iron deposit, also known as the Iron Mountain claim, was examined by G. L. Thompson, an engineer of the Bureau of Mines, in January 1943. As a result, the Division of Geophysical Exploration 3/ made a magnetorater survey of the deposit in June 1944, and the Mining Branch included it in a,project to explore Nevada iron deposits.The Bureau explored the deposit from September to November 1944 by means of 643 feet of diamond drilling and 445 feet of trenching holes were drilled, all of which penetrated more than: 100 feet of good-grade magnetite, although nearly all the ore except that found in the first hole contained an excessive amount of sulfur. Trenching was done largely over the first two holes, PS-1 and PS-2, and exposed the full width of the ore.The deposit is in Nye County, Nevada, 7.7 miles east of Gabbs. The property was discovered in 1902 was patented in 1907. There has been no production from the property and except for the Bureau's investigation,,has not been, explored since it was patented.Magnetite is the principal ore mineral; it occurs as fine-grained particles associated with sulfides and cemented with talc and calcite."

Feb 1, 1947

By D. P. Chakraborty

Joda East Iron Mine, one of the captive iron ore sources of Tata steel, located in the state of Odisha in eastern India caters to approximately 45% of the iron ore requirement of the Jamshedpur Steel Plant. The iron ore occurring in the mine having high in iron content along with high in alumina. Clay and gibbsite are the predominant mineral phases present as surface coating, fracture filling and/or free occurring and are responsible for alumina content higher. Alumina in iron ore impacts the techno-economic performance of a steel plant by impacting sintering and blast furnace productivity. The impact is even higher when it comes to fine ore used in the blast furnaces in the form of sinter as it constitutes a major portion of the blast furnace burden. Therefore, it is beneficial to upgrade iron ore in the mine head and to reduce alumina before it is subjected to agglomeration. Mineralogical test works reveal, that alumina in iron fines is mainly associated with the clay attached to the hematite particles, either free or interlocked to a very fine size. The paper describes the efforts made to reduce alumina in the iron fines in Joda East processing plant, without much of capital investment for a very sophisticated fines beneficiation circuit. In this process, a suitable dispersant was added in the plant that dispersed the masked slime coating over the iron ore fines, thereby making a better quality iron ore fines with reduced alumina content. The alumina in fines improved by 0.2 units? means from a label of 2.4-2.6 % reduced to 2.2-2.4 %. With this initiative, not only the primary objective of alumina reduction is met but also it has given substantial benefit in reduction of silica and as well as moisture in product. This moisture reduction also has given bottom line impact by reducing idle freight and royalty.

Sep 1, 2012

By A. A. Remes

High precision on-line particle size distribution measurement of mineral slurries has recently be-come available. It provides new tools for the development of monitoring and optimization methods for mineral grinding and separation circuits. The paper presents the development work at the Kemi chromite concentrator plant of Outokumpu Tornio Works in Northern Finland. The Kemi concentrator processes annually 1.2 Mt of chromium ore. The products are upgraded lumpy ore and metallurgical grade concentrate. The concentrate is produced using gravity separation methods, preceded by a rod mill - ball mill grinding stage. The separation process performance is strongly dependent on the particle size distribution of the grinding product at the Kemi plant. Particle size distribution has a significant effect on the concentrate grade and recovery. Currently a new laser diffraction based on-line particle size analyser is used for monitoring the grinding product. The analyser system allows the measurement of the whole cumulative particle size distribution simultaneously. It provides a wealth of new measurement information for process control. A monitoring and optimization scheme for grinding and gravity separation based on the particle size information is presented. The goal is to minimize the production of fine slime, and subsequently to improve the concentrate quality and minimize chromite recovery losses. Data-based recursively identified linear PLS process models are developed for optimization purposes. The preliminary results of the monitoring system operation in on-line use are presented.

Jan 1, 2014

By D. P. Kedzie, R. A. Dodd

The fatigue strength, fatigue hardening, and effect of fatigue deformation on subsequent age hardening of supersaturated Al(Cu) solid solutions have been determined as functions of alloy composition and temperature. The fatigue strength/tensile strength ratios, determined at 150°, 25°, and -195°C, decreased with increase in alloy content for all temperatures, but the F.S./U.T.S. ratios at -195°C decreased much more rapidly than did the ratios for 150" and 25°C. This suggested that strain aging and/or age hardening occurred during tests at higher temperatures. Additionally, the F.S./U.T.S. ratios at 150°C exceeded those at 25°C for all compositions, indicating greater strengthening during fatigue at 150°C. The effect of fatigue or tensile deformation at 150°, 25°, and -195°C on subsequent age hardening showed that the deformatzon increased the rate of precipitation and indicated that mechanically produced vacancies were probably formed during deformation. Fatigue hardening was studied at 150°, 25°, and -195°C, and the effect of room-temperature rests after 10 and 100 cycles was examined. The results confirmed that strain aging occurred at the higher temperatures . DURING the last 15 years various mechanisms of fatigue crack nucleation and growth based on dislocation and vacancy interactions, operating singly or collectively, have been proposed. The probable consensus of present opinion is that the fatigue process in pure metals essentially involves dislocation interactions, and that vacancies formed by such interactions play a minor or inconsequential role. However, there is some evidence that age-hardened alloys tend to overage during fatigue, probably by local vacancy-enhanced diffusion, and strain aging also might be important in selected cases. Furthermore, it has been established that the behavior of quenched-in vacancies in Al(Cu) and other solid solutions is composition-sensitive. Therefore, it seemed worthwhile to investigate various aspects of the fatigue behavior of supersaturated Al(Cu) alloys and to examine the results in terms of vacancy-enhanced effects. EXPERIMENTAL The alloys used in this investigation were prepared from 99.994 wt pet A1 and OFHC copper, the latter containing 0.04 pet 0 as the principal impurity. Six alloys were made, containing, by actual analysis, 0.58, 0.96, 1.96, 2.85, 4.45, and 5.51 wt pet Cu. They were induction-melted in air in graphite crucibles, cast as 7-in. by 7/8-in.-diam rods in graphite molds, and hot-rolled to 5/8 in. diam. The experimental work was a three-part program involving the determination of a) 10' cycle fatigue stresses as a function of alloy composition and temperature; b) the effect of fatigue deformation on subsequent aging of the supersaturated alloys; and c) fatigue hardening as a function of alloy composition and temperature. For determining the 105 cycle fatigue stresses, a portion of the 5/8-in. stock was machined into Krouse rotating cantilever beam fatigue specimens, 2 in. in length by 1/4 in. minimum diameter. These were tested at +150°, 25°, and -195°C (liquid nitrogen) on a Krouse high-speed machine, with special weights to provide lower -than-normal loading ranges, this being necessitated by the small load requirements of those alloys of lower copper content. For the high-temperature tests a small resistance heater was designed to clear the collets and fit in between the chucks, while for the low-temperature tests a hollow nylon cylinder was used, having closed ends drilled to pass a fatigue specimen, and positioned similarly to the heater. A plexiglass container completely enclosed the fatigue machine; rubber gloves fixed to ports in the walls enabled the machine to be operated from outside the box. A tray of magnesium perchlorate dried the air in the container and prevented both atmospheric corrosion fatigue at room and elevated temperatures and troublesome ice build-up at low temperatures. A total of ten to fifteen specimens was used for each combination of alloy composition and temperature. The result of each test was plotted on a standard S-N diagram, and the next stress was selected on the basis of the trends indicated by previous specimens. In this manner a small portion of the S-N diagram was constructed, and the 105 cycle fatigue stress obtained. Small Krouse fatigue specimens were also used to study the effect of cyclic prestrain on subsequent

Jan 1, 1964

By J. R. Nawrot

Reclamation of potentially acid producing coal processing waste requires a 4-foot cover, and/or treatment to allow vegetation establishment. If not planned properly, soil covering alone does not prevent refuse acidification or formation of acid seeps. Adequate neutralization enhancement prior to soil covering can maintain an alkaline environment in the soil refuse interface and prevent acidification. Direct vegetation establishment using only limestone amendment (without soil cover) can successfully reclaim aged and weathered fine (Blurry) and coarse (gob) refuse if adequate neutralization treatment is provided for the oxidized surface zone. Acid seeps, representing an "after-the-fact" verification of an imbalance of acid-base equilibrium may also be corrected using upslope alkaline recharge techniques. Concentrated alkaline recharge pools have been constructed above previously soil covered acid gob at the Peabody Will Scarlet Mine to abate acid seeps. Preliminary monitoring results (1989-1992) from a concentrated alkaline recharge pool demonstration project in the Pit 4 area of the Will Scarlet Mine have documented a 50 to 80 percent reduction in acidity in the principal recharge pool groundwater zone. A 22% reduction in acidity has occurred in the primary seeps located downslope from the alkaline recharge pools. The initial improvements in water quality are seen as a positive indication that groundwater acidity will decrease further and amelioration of the acid seep will continue.

Jan 1, 1993

By Siqing Liu

A low-grade cassiterite-magnetite ore from Sichuan province, China, is finely disseminated, assaying 0.39% Sn and 23.20% Fe, respectively. Mineralogy studies show that the fine-sized cassiterite is mainly disseminated in iron minerals and gangue. Moreover, the embedded size of cassiterite is very fine and must be ground to -0.01 mm to achieve a degree of liberation of about 90%. Therefore, fine grinding needs to be conducted to get a high quality tin concentrate and a great loss of tin cannot be avoided when treating the ore by gravity concentration. Based on the above facts, a two-stage separation, with a low intensity magnetic separator and a shaking table, was selected to test the ore. Compared with other similar plants, a relatively good separation has been achieved. Three acceptable products for smelters were obtained as following: iron concentrate assaying 61.69% Fe with a recovery of 75.09%, tin concentrate assaying 27.21% Sn with a recovery of 56.97% and a sulfur concentrate assaying 40.86% S with a recovery of 32.03%, respectively.

Jan 1, 2011

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By C Parihar, R Garg, A Bhandari, S Bhandari

Blasting can impact the efficiency of entire downstream mining operation. Individual technology solutions for blasting have been available in the industry for many years but all of them only cater for certain aspects of blasting. Many of them are based on individual research and/or experiences. Some of the available software solutions are not suitable to be used in the field as that they need advanced skills or tools. Also, most do not take technology advancements like mobility, advanced data analytics, web solutions and integration into consideration. Hence, no technology platform is currently present in the industry that addresses all potential needs a blaster may need in an integrated manner.This paper presents an integrated solution that takes care of all aspects of blasting – design blasts according to mine plan; collect data after drilling has been carried out (as there is often difference in designed and actual drilled hole locations in the field); predict blast results in terms of fragmentation, flyrock, ground and air vibrations, wave front reinforcement and flyrock distance; and after assessment, allows changes in charging, delay timing and sequence. The technology solution is a secure, cloud-hosted, web-based software-as-a-service solution that can be accessed from anywhere. Also it has a mobile app, which is available for both Android and iPhone/iPad. The mobile app is also integrated with the web-based solution using application programming interface calls to the central data repository.Case studies for two limestone mines are presented where this solution is being used in its initial format. This software platform enabled analysis of the outcome from a previous blast pattern and then subsequently allowed optimisation of blasting operations based on historical data. Uses of this platform have resulted in improved key performance indicators in these two limestone mines. The mobile app as part of this platform enables extensive field blast data capture and analysis and also various predictions before a blast. Data collected include blast parameters, individual hole charging, initiation pattern, videos, photographs and vibration records for analysis/reporting. The key features of the solution are a blast designer, a detailed blast data collection/analysis and a series of environmental predictors. These predictors give blast results in terms of fragmentation, flyrock, ground and air vibrations and wave front reinforcement and take remedial steps before blasting to optimise and control adverse environmental impact. Many features, such as fragmentation predictor and mobility solution, are completely unique features that are not available elsewhere in such a field personnel-friendly manner.CITATION:Bhandari, S, Parihar, C, Garg, R and Bhandari, A, 2015. An integrated technology solution for optimised and environmentally-controlled blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J. G. Faller, L. P. Skolnick

The distribution of cobalt and vanadium over non-equivalent crystallographic sites in C14-type Zr(VCo), alloys has been investigated. An anomalous X-ray scattering technique developed by Skolnick, Kondo. and lavine7 by which the separation in the scattering factors of two similar atoms can be enhanced was employed. Six alloys spanning the pseudobinary section ZrV1.6Co0.4-ZrVO.6CO1.4 at 10pct steps showed a nonrandom compositionally dependent distribution. Specifically, at high vanadium content cobalt preferentially occupied sites of type (6h) and vanadium, sites of type (2a; at low vanadium content the reverse was observed. In addition to the distribution fraction the structural parameters x and z were obtained. There was no significant deviation of these parameters from those obtained in the ideal C14 structure. Certain suggestions are made to account for the observed nonrandomness in the distribution of atoms on the two types of sites. INTERMETALLIC compounds of formula AB2 iso-morphous with MgCu2, MgZn2, and MgNi2 are known as Laves phases. Because Laves phases exhibit high symmetry and coordination numbers, the highest possible for an AB2-type compound,1 they are among the most frequently observed compounds in nature. In recent years interest has centered about the purely transition metal Laves phases2-' in efforts to understand the function of atomic size and electronic structure in the formation of these compounds. It has been observed that pseudobinary Laves phase systems often show a variation of structure across the phase diagram. Such a system is the ZrV2-ZrCo2 in which the structure varies from cubic MgCu2 to hexagonal MgZn2 to cubic MgCu2.4 Some understanding about the conditions under which the second modification is stable can perhaps be gained by studying the distribution of cobalt and vanadium atoms on lattice sites in the MgZn2 modification of the system ZrV2-ZrCo2. In both the MgZn2 and MgNi2-types there exist nonequivalent positions open to occupancy by the B element, whereas in the MgCu2 prototype all sites are equivalent. Skolnick, Kondo, and La-vine7 have developed an anomalous scattering technique suitable for this type of investigation. Whereas the influence of size on the formation of a Laves phase is well recognized, no substantial evidence has been put forth in support of the size ratio dependence of a particular prototype. Berry and Raynor8 suggested that RA /RB ratio does indeed affect the type of structure that is chosen, MgZn2 compounds tending to cluster about 1.225 while MgCu2 compounds were found at larger deviations from this ratio. Dwight,3 however, from a study of 164 Laves phases does not believe this generalization to be justified. Electronic effects are certain to play a part in the stability of Laves phases in general and in the choice of a structure type in particular. For example, size along would favor the formation of Laves compounds of Ti, Zr, Hf, Ta, or Nb as the A element with nickel or copper as the B element. The absence of such is attributed to an unfavorable electron : atom ratio by Elliott and rostoker.4 Early experiments of Laves and witte9 with pseudobinary and pseudoternary systems of the three prototypes established the dependence of crystal structure upon electron: atom ratios. They observed that the MgCu2 structure dissolved elements of higher valency until the electron: atom ratio of =1.8 was reached; the MgZn2 likewise dissolved elements of lower valency replacing zinc. witte,6 from calculations of the electron : atom volumes of Brillouin Zones, obtained limits of stability for the prototypes MgCu2 and MgZn2. Elliott and Rostoker4 used these limits with considerable success in the all-transition element Laves phases they investigated. According to witte,6 compounds between the electron :atom ratios of 1.80 and 2.32 were of the MgZn2 type; those above and below exhibited the MgCu2-type structure. On the basis of these limits and an assumed valency of zirconium based upon the near tetra-valence of titanium, Elliott and Rostoker obtained valencies for the first transition series elements. For the Laves phases with which this investigation is concerned, ZrV2 and ZrCo2, the authors calculated electron :atom ratios of 2.54 and 1.56, respectively. These ratios are for the MgCu2-type structure and straddle the stability band of the MgZn2 modification. One could, therefore, predict that a pseudobinary system ZrV2-ZrCo2 should pass through the MgZn2 modification in traversing the composition diagram from one end to the other. Implicit in this assumption is a smooth change of the electron: atom ratio from 2'54 to 1.56. MOSS10 states that his finding the low temperature structure of ZrCr2 to be C15 instead of C14 alters greatly Elliott's valency of zirconium and hence the assumed valencies of the other metals. Such a quantitative correlation of structure with electron : atom

Jan 1, 1963

By F. M. Wang, J. P. Lin, G. Y. Tang, H. C. Zhou, Y. F. Liang, F. Ye

"Fe-6.5%Si alloy is a very excellent soft magnetic material compared with conventional Si steel (Si content ~ 3.5%), especially in high frequencies with reduced iron losses and noises. But it is hard to be fabricated due to its brittleness at room temperature. Dynamic electropulsing is applied to the cold rolled Fe-6.5%Si sheet during tensile deformation. Mechanical and microstructural properties are investigated with different electropulsing and strain rate. It is found that the yield stress decreases and the elongation increases dramatically with the application of dynamic electropulsing. It is indicated that the work hardening could be reduced with the dynamic electropulsing during deformation, which provides a promising way to fabricate this alloy sheet much easier.Introduction Fe-6.5%Si (weight percent, same as below) alloy has more excellent soft magnetic properties compared with conventional silicon steel (Si content ~ 3.5%), such as higher resistivity, higher permeability, near zero magnetostriction, etc. and exhibits much lower core losses and noises [1]. However, Fe-6.5%Si is very brittle at room temperature and hard to be fabricated in strip by conventional hot-cold rolling process [2]. This lack of low-temperature ductility has been generally attributed to structural ordering ofB2 and D03 phases [3]. Several methods have been developed to avoid its brittleness, such as chemical vapor deposition (CVD) [4], rapid quenching [5, 6], dipping and diffusion [7, 8], direct powder rolling (DPR) [9], etc. However, hot-cold rolling method is still of interest for industrial applications. In our previous work, this alloy can be cold rolled after certain thermomechanical process and heat treatment [10-13]. The cold rolled sheet exhibits some extent of ductility [11]. However, side cracks are common for the rolled sheet, it is very necessary to improve the ductility of this alloy by other technical applications."

Jan 1, 2012

By G. M. Clarke

Minerals are certainly where they are found. The undemocratic distribution of the world's mineral wealth has created an incongruous inbalance: mineral-rich, scarcely populated countries supply highly-populated industrialised countries that in turn consume more minerals than they produce. This has been as much a generating force for colonisation, invasion, and war as religion, political ideals, or megalomania. The Industrial Revolution of the seventeenth century was born in Britain, a country with large domestic resources of coal, iron, lead, zinc, copper, tin, etc., as well as a large population. As consumption outstripped production imports filled the gap, particularly from its worldwide colonies. For example, when Canada was founded in 1867 more than 905 of its investments were British financed, and much of these were mineral-based. The British made similar investments in South East Asia, Australasia, the Caribbean, and elsewhere, as did the other industrialised Western European countries hungry for raw materials. Later the United States emerged as a leading industrial power, again due largely to its abundant natural resources. Consumption soon exceeded production and foreign sources were saught. American business went exploring abroad ant many a mineral resource was developed almost totally on the basis of the US market many .thousands of miles away. Closer to home, Canada was also an obvious target for the US with its rich mineral resource base, small population, and geographical juxtaposition, so much so that about the time of the 1914-18 War the US took over from Britain as the major investor in Canada, and this peaked in 1967 when the US accounted for 80% of the country's foreign investment. After the 1939-45 War Japan joined the ranks of the USA and Western Europe as industrialised powers, and they too searched the world for the deposits lacking in their homeland.

Jan 1, 1981

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992