Search Documents

By George S. Austin

Adobe, dried mud bricks, have been used since before historic time in the construction of dwellings. Building materials are normally evaluated for thermal performance based on measurements known as R- and U-values. The R-value is an indicator of the ability of a wall to insulate effectively and the higher the R-value, the better it is as an insulating material. The U-value, or value of conductance, is the reciprocal of the R-value and reflects the rate at which heat is conducted through a material. But the "heat capacity of the wall" must also be considered. This measures the length of time that passes before a steady state of heat flow is achieved. The effective U-value measures both the resistance to the transfer of heat and the capacity to hold heat. These latter value make adobe a far more interesting as a modern building material that was formerly recognized.

Jan 1, 1983

By Y. F. Hou

This paper reports the results of the study of the influences of concentration and modulus of sodium potassium silicate solution (Na-K activator) and curing mode on the phase composition, mi-crostructure and strength development in the geopolymers prepared using Class F fly ash. X-ray dif-fraction (XRD), Fourier transform infrared spectroscopy (FTIR) and MAS NMR are utilized in this study. It shows that the compressive strength increases while sodium potassium silicate solution modulus increases, but when modulus exceeds 1.7, the compressive strength decreases, and it decreases markedly while modulus is greater than 2.0. The compressive strength improves with increase of sodium potassium silicate solution concentration. When the concentration is 36%, the compressive strength reaches the maximum. Elevated temperature can increase the strength of samples synthesized using sodium potassium silicate solution with 32% concentration and modulus 1.2. Compared to the strength of the sample cured at 50?, the strength of the samples cured at 65? and 80? are higher at 1 day and 3 days, but when cured at 80?, strength is smaller than that cured at 50? for 7 days. When temperature is too high, too long curing time will decrease the strength. Long precuring at room temperature before application of heat is beneficial for strength development, and there is about 10%~50% increase in strength of the samples cured at 1 day precuring and 2 days elevated temperature as compared to the strengths of the samples cured for 3 days at elevated temperature or cured for 28 days at room temperature. The main product of reaction in the geopolymeric material is amorphous alkali aluminosilicate gel.

Jan 1, 2014

By Kush Patel

This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser.

Feb 1, 2020

By A. J. Getz

The paper reviews the status of the major precious metals projects in Australia, Papua New Guinea, Indonesia, the Philippines, and New Zealand. The projects may be at the stage of exploration, development, operation, or expansion. The paper covers project location, reserves, method of resource exploitation, anticipated production, and other unique conditions.

Jan 1, 1990

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By D. L. Jones

The leaching of natural chalcopyrite was studied in both ferric sulfate and ferric chloride solutions. The chemistry of the two reactions is quite different, with substantial sulfur oxidation occurring only in sulfate solutions. Ferric chloride is a more effective reagent, for the leaching rate is greatly increased with finer particles and higher (Fe+++), and unaffected by high (Fe++); none of these advantages are found with ferric sulfate. In addition, the morphology of leaching appears to be different, with ferric sulfate leaching preferentially along fissures or grain boundaries. The kinetics were found to be linear over an extended period, rather than parabolic as reported elsewhere. An explanation of the observed phenanena is proposed using the electrochemical theory of leaching, and experimental measurement of the mixed potential of the mineral during leaching.

Jan 1, 1976

By D. C. Seidel

The role of surface charge in soluble salt flotation, which was developed in Part 1, is extended to relate the theory to the specific phenomena of KCI- NaCl separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed.

Jan 1, 1967

By C Bie, S Li, P Xiao, P Zhao, H Lin

"Based on solid simulation material research, the simulation conditions for methane and coal solid-gas coupling were obtained using solid-fluid coupling theory. Using sand as the aggregate and paraffin and oil as the cementing agents, a material suitable for solid-gas coupling simulation was developed. A permeability testing instrument was also developed, and the compressive strength, brittleness parameters and seepage velocity of material were tested with different aggregates. The results showed that as the paraffin content increased, the compressive strength of the material increased but the permeability decreased. The oil removed the drawback of intensely changing material compressive strength. By setting a different ratio of aggregate to cementing agent, it can simulate rocks with different strengths and permeability. Applying the material to a mining simulation experiment revealed a relationship between methane seepage velocity and overlying strata movement. By extracting pressure relief gas from Shanxi Tianchi coalmine drainage, the authors found that the mining fissure zone was a storage area of pressure relief gas, and a gas drainage system can be placed to achieve good results. CITATION: Li, S, Zhao, P, Lin, H, Bie, C, Pan, H and Xiao, P, 2015. Character of simulation material of coal – rock and gas solid-gas coupling and engineering application, in Proceedings The Australian Mine Ventilation Conference, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By Pritii Tam Wai Yin, Tony Leong, Neetu Bansal, James Vaughan, Amiel Boullemant

Mercury is a toxic element that is associated with many industrial activities including the Bayer process. Mercury is known to enter the Bayer process with the bauxite feed material and has the potential to accumulate as the process solution is recycled. This paper explores the speciation of mercury in Bayer process streams. The process parameters considered are the oxidising-reducing potential, basicity and temperature. The results of a refinery circuit survey are presented and compared with the thermodynamic predictions. Electrochemical measurements on relevant synthetic systems are also included.

Jan 1, 2014

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By Percy Castillo Neira

El presente texto señala el empleo del carbón no solo como sustituto del petróleo, sino como una posibilidad energética para el desarrollo de las zonas menos favorecidas. En ese sentido, esta puede constituirse en factor de progreso y promoción de la descentralización del paísv y las posibilidades de su empleo debe orientarse a todas las zonas del territorio peruano aprovechando su facilidad de uso en el mismo lugar de producción.

Jul 1, 1985

Datun Concentrator currently processes complex sulfide ores in Gejiu Municipality, Yunnan Province, China. The ore contains much higher arsenic than other ores. The run of mine ore is fed to the concentrator to recover copper and tin by bulk flotation and gravity concentration, and then the other sulphides, such as pyrite, arsenopyrite, etc. didn?t get utilized and are discarded as tailings due to the high arsenic content. In order to utilize the pyrites in the tailings, a series of tests have been conducted for finding the solution of arsenic removal from high arsenic-bearing pyrite concentrates through simple flotation process. By means of orthogonal experimental design, the optimized levels and main factors have been found out for the roughing stage. Through selection of the effective in-organic depressants for the arsenic-bearing minerals, the arsenic in the pyrite concentrate can be removed to meet the requirement of sulfuric acid plant (As%=0.5%) by the open flotation process, i.e., one-time roughing and two-time cleaning.

Jan 1, 2014

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

By L. R. Smith

BUTANE OPERATED drilling rigs are a recent innovation in the petroleum industry, so extensive data on their operation are not available. However, experience indicates that, within limitations, as much can he accomplished with butane as with steam, at a decided reduction .in expense of installation and cost of operation. Commercial butane is a liquid motor fuel similar to gasoline, but much more volatile, so that it has to be stored under pressure. At 10° F. it is liquid at atmospheric pressure, but at 100° it has a pressure of 70 lb. or more. As soon as the pressure is reduced, it turns to vapor and in that state is far more easily mixed with the air necessary for combustion. Butane occurs as a by-product in the absorption process of natural gasoline extraction from casing-head gas. The product has been used to some extent 10 raise the octane value of gasoline. However, because of its volatile nature, such admixture is stable only to a limited degree. Attempts also have been made to introduce the product in a gaseous form into oil- hearing formations in repressuring work. It has, however, until recently, for the most part been wasted.

Jan 1, 1937

By R. Singhal

Canada's coal production is approximately 65.4 million tonnes of which 95 % is produced by surface mining methods mostly from the three Western provinces (British Columbia, Alberta and Saskatchewan). The mines are highly mechanized; productivity gains during the past few years have ranged from 60 -80%. Truck/Shovel methods are common although Saskatchewan lignite is almost exclusively mined by draglines. This paper provides an overview of Canadian Coal mining industry vis a vis surface mining. Emphasis is on application and utilization of mining equipment and associated mining methods.

Jan 1, 1994

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By Stefano Utili, Robert Pell, Nelson Morales, Cristobal Valderrama, Andrea Agosti, Guillermo Albornoz

The overall slope angle (OSA) of pit walls plays a crucial role in the financial return of open pit mines. The work showcases a novel design methodology where non-planar geotechnically optimal pit walls with an OSA steeper than what is used in current design practices are employed without compromising mine safety, i.e. the optimal profiles are featured by the same Factor of Safety (FoS) than their traditional design counterparts. In the current design practice, pit wall profiles are often designed to be planar in cross-section and the profile in between ramps especially tend to be defined by a constant inter-ramp angle.

Sep 30, 2022

By F. G. Clapp

IT is to be hoped that no casual reader will erroneously refer to the latest publication' of the Division of Public Relations of the American Petroleum Institute, as being "Petroleum Facts and Fancies." The facts are so faithfully derived and the figures are so authentically sponsored by the highest sources that no person can read this valuable volume (287 pages and numerous tables) without being convinced that every- thing therein set forth is "the truth and nothing but the truth." Yet, having read the volume from the perspective of the world's petroleum industry and with a critical attitude that comes from years of study of the subjects discussed, I find myself tempted to cogitate and to envisage a few of the fancies that come to mind as a fitting sequel.

Jan 1, 1929

By Daniel F. Meyer, William C. Paschen

INTRODUCTION The problems involved with moving millions of tons of rock are being addressed by nationally recognized tunnel contractors who have converged in Chicago over the past 5 years. This wealth of expertise has been needed to meet the risk and challenge of constructing the world's largest network of underground tunnels which in turn has required a dramatic advance in the art and science of tunneling. These pioneers, through innovation, adaptation, and hard work, have eliminated the one major concern of The Metropolitan Sanitary District of Greater Chicago - how to move 8 million tons of rock. The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves 122 municipalities covering 866 square miles in Cook County, Illinois. Of these cities, towns, and villages, 53 have combined sewer systems. On an average of once every four days, these systems overflow about 4 million gallons of combined sewage and rainwater into the area's rivers and canals. The overflows occur at approximately 640 outfall locations of which 10% are owned by the MSDGC, with the remainder of the points belonging to various other municipal bodies. All those who own these "point" sources of pollution are in violation of Illinois State and Federal regulations. To enable its member municipalities to come into compliance with State and Federal law, the MSDGC is implementing its Tunnel And Reservoir Plan (TARP). TARP is a regional solution to the problem of combined sewer overflow in the metropolitan Chicago area. TARP will greatly reduce the pollution of area waterways by intercepting the combined sewage and rainwater carried in the existing sys-

Jan 1, 1981