Search Documents

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By J. Kretschmann, R. Amiri

"The Sangan iron ore mines (SIOM) in Iran are located in a remote area near the Afghanistan border. The SIOM deposit contains a geological resource of 1.1 Gt (1.2 billion st) of mostly magnetite with an iron (Fe) grade ranging from 27 to 61 percent. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development is an influential ethical concept in mining all around the world. However, a successful realization of a sustainable development plan is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes sustainable development activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators were filtered to the ones with the highest priority for the stakeholders. Moreover, Islamic values and Iranian regulations and their influences on SIOM were analyzed.Mining industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron, etc., with 33.5 Gt (37 billion st) of proven reserves and more than 51.7 Gt (57 billion st) of potential resources. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5,316 active mines and 84,922 employees in the whole country in 2012-2013 (2) and, according to the statistics published by Central Bank of Iran (CBI) in 2011, the share of this sector in the gross domestic product (GDP) of the country was 1.2 percent (3)."

Jun 1, 2016

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Richard D. Hagni

Microscopic examination of selected, representative, unweathered samples of Birmingham, Alabama, Silurian, sedimentary iron ores has fully revealed the nature of the phosphorous-bearing mineral grains. The grains are composed of carbonate-fluorapatite (collophane), range in size from 1 um to 2.25 mm, and exhibit varied types of intergrowth with hematite. Modal analyses conducted under cathodolumi-nescence have provided quantitative data on the a3undance of each of 15 types of phosphorous-bearing mineral grains and made it possible to assess the potential phosphorous liberation from four types of iron ore. The results indicate that 27% of the total phosphorous contained in the iron ores in the western part of the Birmingham district can be expected to be liberated by fine grinding; 60% for ores in the eastern part of the district.

Jan 1, 1982

By Lucas Lopes da Costa, Sergio Neves Monteiro, Rômulo Leite Loiola

"Composites with DGEBA/TETA epoxy matrix reinforced with thinner and continuous bamboo fibers stripped from culms were mechanically characterized by tensile tests. Specimens with up to 30% in volume fraction of aligned fibers were tensile ruptured at room temperature. The results showed a steady increase in both the ultimate strength and the elastic modulus of the composites with the amount of incorporated bamboo fibers. The fractographic analysis by scanning electron microscopy showed evidence of moderate adhesion between the bamboo fiber and the epoxy matrix. This fiber/matrix adhesion by interaction mechanism apparently justifies the improved tensile properties of the composites.IntroductionIn recent years polymer composites reinforced with natural fibers, mainly those lignocellulosic obtained from plants, have been subject to extensive research works [1-5]. Environmental, economical, societal and technical advantages of these composites are motivating their substitution for similar polymer composites reinforced with synthetic fibers. In particular, R & D efforts have been conducted aiming to replace glass fibers composites that are comparatively more abrasive to equipments, non-recyclable, more expensive, heavier and toxic [6]. Among the many lignocellulosic fiber composites being investigated, those fabricated with bamboo stripped fibers, i.e., fibers longitudinally cut from the culm, still need information to support possible industrial applications. Several works, however, have been dedicated to bamboo stripped fibers as possible reinforcement of polymer composites [7-17]. These works reported mechanical properties that could markedly vary with the type of polymer matrix, the fiber disposition (if continuous, aligned, short-cut, mat interlayered, etc) and the test condition."

Jan 1, 2011

By M. Buchmann, T. Mütze, F. Heinicke

Dry air classification is a well-known technique used for decades in the cement industry to separate material in the size range of 0.01-1.0 mm. Additionally, in corresponding dry grinding circuits with effective machines such as High Pressure Grinding Rolls (HPGR), the energy consumption can be reduced compared to wet applications. These dry systems are not state of the art in minerals processing plants, but first prototypes have been installed and an increasing number of projects are starting to evaluate this option. One challenge in this field is the mineral composition of ores, which have, by far, a higher variety in density and size than those of cement. High density particles such as iron- containing ones have higher settling rates than low density silica particles of the same size. The main question to answer in this paper is how to evaluate this effect, so a quantitative method using Mineral Liberation Analyses was developed to calculate two-dimensional partition curves. Additional statistical analyses allow for isolation and quantifying the interaction of density and size, enabling engineers to consider this effect for the sizing of process plants. The paper will present the method and selective results for a compounded ore of iron and silica. Keywords: HPGR, air classification, partition curve, MLA

Jan 1, 2020

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

By Christophe Bragard, Marte Gutierrez, Haotian Zheng, Michael Mooney

This paper proposes a framework for applying surrogate-based approaches to evaluate SEM construction, which can both benefit the uncertainty analysis in the design stage and real-time calibration during the construction process. The performances of four surrogate modeling approaches, namely back-propagation neural network (BPNN), support vector regression (SVR), random forest (RF), and polynomial chaos expansions combined with Kriging (PCK), were evaluated and compared. A variance-based global sensitivity analysis (GSA) was performed on the surrogate predictor to quantify the impacts of geotechnical parameters on the deformation responses induced by SEM tunneling. The Regional Connector Crossover Cavern project constructed in Downtown Los Angeles was set as the benchmark problem to demonstrate the efficiency and reliability of the proposed procedure.

Jun 13, 2021

By D. W. Scott

Ontario has a diverse industrial mineral resource base including abundant resources of structural industrial minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone and dolostone. These resources are used in the production of aggregates, brick, metallurgical stone, fillers, lime, cement and other construction materials. The majority of the operations are in deposits of Paleozoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were over 140 million metric tonnes of aggregates produced in 1985, approximately 115 million tonnes of which was produced in southern Ontario with the remainder being largely from Crown land in northern Ontario. The structural industrial minerals account for over 80% of the value of total industrial mineral production, with the remaining 20% of the value king accounted for by the non-structural minerals being led by salt which is produced in southwestern Ontario. A host of other non-structural industrial minerals are known but production is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite and by-product metallurgical sulphur products (Fig. 1). Location and Market Area Major production is in the area closest to the large markets of urbanized southern Ontario and the northeastern and north-central United States. In general, with the abundant variety and widespread resources of industrial minerals and the large population within 400 miles of most deposits, the market offers great potential. Ontario's 9 million population accounts for about 35% of the entire gross domestic product of Canada of $476.361 billion dollars in 1985. This equates to about 113 of the nation's buying power being within a 200 km (125 miles) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well developed industrial minerals industry fulfilling most of the structural industrial minerals demand in Ontario, as well as a subsidiary demand in neighbouring provinces and states.

Jan 1, 1987

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By Herbert Everest

THE idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentage expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2: Development, including all necessary yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, drawslate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1 ½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the Beadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high.

Jan 1, 1916

By Herbert A. Everest

The idea of economical production is usually associated with large operations, tonnages, and mines, with even larger capital behind them. , Nevertheless many small mines operate in the shadow of large competitors and make a good showing on the capital invested despite larger overhead expenses. For the purpose of this discussion I will divide the cost of production into classes, and specify opposite each the approximate percentagc expended thereon: 1. Labor, including miners and company men; 60 to 75 per cent. 2. Development, including all necessary .yardage, room turning, crosscuts, etc.; 7 to 12 per cent. 3. Deadwork, covering payment to miners for handling falls, draw-slate, or faults, rock work, water, and in general, all nonproductive labor; 3 to 7 per cent. 4. Supplies: mine timbers, oil, brattice material, lumber, cement, and repairs to equipment; 2 to 6 per cent. 5. Expense: management, selling, office, taxes, etc.; 1 to 5 per cent. 6. Depreciation of coal reserves and royalties; 6 to 10 per cent. 7. Depreciation of equipment and interest on capital invested; 1 to 3 per cent. 8. Fuel; ½ to 1½ per cent. The labor cost for a small mine is relatively much lower than for a large mine, particularly the sum paid to company men. Idle-pay expense is cut to a minimum; the labor item being larger than all the others together, a saving in labor makes a decided showing on the total cost. The development charges in small and large mines are about the same. There should be a small showing on the deadwork item in favor of the small mine. The unit cost for supplies is usually small in the small mine. The operator of the small mine finds, owing to a limited tonnage, that the expenses of management, selling, etc., are abnormally high. The item, depreciation of coal reserves and royalties, is usually about

Jan 1, 1916

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By Bráulio Salumão de Oliveira

Este estudo avaliou oportunidades de integração entre requisitos ambientais e econômicos durante etapas iniciais do desenvolvimento de produtos. Como principal ferramenta foi utilizado o Mapeamento de Fluxo de Valor, associando conceitos de manufatura enxuta, Design for Manufacturing and Assembly (DFMA) e Ecodesign, aplicado a um item de mobiliário aeronáutico em material compósito. Os resultados apontam que o tempo total de fabricação poderia ser reduzido em até 43%, além da otimização logística. A forma de construção influencia diretamente os impactos ambientais e oportunidades de utilização de matérias-primas menos agressivas foram apontadas como sugestões. O aspecto visual dos Mapas de Fluxo de Valor facilita a análise das informações e a tomada de decisão na seleção de materiais e processos que minimizem desperdícios e impactos ambientas na manufatura.

Oct 30, 2017