Search Documents

By S. Moussa

The formation of boron-doped nickel aluminides Ni3AI, (76 at. % Ni) from elemental powders by reaction synthesis using reactive sintering was studied. The process involves the mixing of elemental powders of nickel and aluminium with various wt % of boron up to 1 wt % boron. Nickel and Aluminium powders were mixed in the correct proportion to form the intended boron-doped nickel aluminide intermetallic. XRD, SEMI EDS, Image analysis and Archimedes principle; were used to study the effect of Boron addition on the final microstructure, bulk density, average grain size of as reactively-sintered nickel aluminides (boron-doped), compared with no boron addition. The results showed that at greater boron content than 0.3 wt %, a two-phase non-equilibrium microstructure of consisting of NiAI phase in NiJAI matrix was formed that have been primarily retained even after heat treatment for 5 hours at 1000 °C. Boron was present in solid-solution within both the NiAI and the Ni3AI (in greater amounts) phases.

Jan 1, 2001

By Rodrigo de Oliveira Pezzin

Devido ao fato que a exigência por menores teores de enxofre em alguns tipos de aços, torna-se interessante investigar a eficiência na dessulfuração dos materiais já conhecidos com matérias primas alternativas. Duas dessas novas matérias primas que podem ser utilizadas no processo de dessulfuração são o resíduo de mármore e a sodalita. Desta forma, o presente trabalho tem como objetivo avaliar a eficiência de dessulfuração em ferro-gusa por misturas contendo resíduo de mármore, sodalita e agentes dessulfurantes convencionalmente utilizados. Os testes foram realizados a 1400°C, em uma atmosfera inerte (Ar) com agitação constante. Os testes experimentais mostraram que 50 a 90% da dessulfuração ocorreu em até 15 minutos. As misturas contendo fluorita foram os que apresentaram maior eficiência de dessulfuração. A adição de sodalita ocasionou uma queda na eficiência de dessulfuração.

Aug 17, 2017

By Aarne Visnapuu

Unmodified pneumatic rock drills may have noise levels of 115 to 130 dB at the operator's position. Experimental modifications have been made to a standard drill to suppress the noise from the three main sources: the air exhaust noise, the noise radiated from the drill, and the resonance noise of the steel drill rods. A prototype model developed at the Bureau of Mines, Rolla Metallurgy Research Center, operates at a noise level below 100 dB. A close-fitting case and muffler unit, consisting of a metallic skeleton filled with viscoelastic absorber and having a durable cover, provided both muffling and noise absorption. Damping alloys were used at strategic points in the drill. Drill steel resonance noise was reduced by a constrained-layer treatment on the outside of the drill rod. The singular and combined effects of the treatments are presented in detail.

Jan 1, 1973

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By W. J. Wolfe

"Quartz Hill is a large, low- to moderate-grade quartz vein stockwork porphyry molybdenum deposit, discovered in 1974 during a regional stream sediment geochemical reconnaissance survey of southeast Alaska conducted by United States Borax and Chemical Corporation. Mineralization is localized in the upper parts of an Upper Oligocene (30 Ma) composite quartz monzonite stock which is emplaced discordantly into older Cretaceous to Early Tertiary terrain of the Coast Range igneous metamorphic complex of the northwest North American Cordillera. Subsequent fault-controlled, complex multi-stage intrusion, concentrated in the core of the Quartz Hill stock, produced successive pulses of hydrothermal alteration and molybdenum mineralization at about 27 Ma. Overall, the deposit is tabular and flat-lying and well suited to open pit mining. The 0.05% MoS2 grade limit covers an area of approximately 1500 m by 2750 m and extends to a maximum depth of 520 m below surface. Details of grade distribution show two separate lobes of higher grade material within the larger low-grade deposit.A ten year program of exploration drilling, underground development, sampling and metallurgical testwork led to a 1983 feasibility study based on a resource of 1600 million tonnes grading 0.127% MoS2 at a 0.08% MoS2 cutoff The large size of the deposit and its homogeneous grade distribution, typically showing gradual outward decrease of grade, makes in pit grade selection practical at several cutoff levels. Cominco Ltd. now reports a Probable Resource of 210 million tonnes averaging 0.22% MoS2 with a further Possible Resource of 1100 million tonnes averaging 0.12% MoS:z. At low molybdenum metal prices which have persisted for 10 years since the molybdenum price spike of the late 1970s and early 1980s, the Quartz Hill deposit is sub-economic."

Jan 1, 1995

By Liyuan Chai, Qin Liu, Bing Peng, Jia Wang, Qiang Zhang

"Electrolytic Manganese Residue (EMR) was used as the main material to prepare cementing material activator for the utilization of the residue from electrolytic manganese dioxide (EMD) or electrolytic metallic manganese (EMM) production. The effects of chemical activation, thermal activation and mechanical activation on retarding activity and excitation activity of EMR were investigated according to the setting time and activity index of EMR-slag cementing material. The results showed that the EMR exhibited good activating performance after being ball-milled for 18 min and then treated for 1-2 hours at temperature range of 350-450 ?. The optimal properties of cementing material activator were achieved at the weight percent ratio 30 : 3 : 5 of EMR/Ca(OH)2/cement clinker.IntroductionMany hazardous industrial solid wastes such as blast furnace slag, fly ash, steelmaking slag, chromic slag and electrolytic manganese residue [1] are generated n China and their amounts increases every year. The accumulation of the solid wastes during past years is very huge and they could be hardly recycled effectively as a sustainable resource. 2.35 billion tons of industrial solid wastes have been produced up to now [2]. It is estimated that they would exceed 3.3 billion tons by the end of 2015 [3]. On the other hand, the quick development of Chinese infrastructural construction needs more cementing materials. The production of traditional building materials consumes lots of natural resource such as clay and limestone and discharges at least 1 ton CO2 and other pollutants per ton clinker [4]. Therefore, it is necessary to develop new types of cementing materials instead of clinker [5,6]."

Jan 1, 2012

By Leticia Gabriela Winck

As escórias de aciaria, além de ser um coproduto da fabricação do aço, desempenham um papel importante na qualidade dos aços produzidos. Entender como elas se comportam durante o processo de refino é fundamental. Por exemplo, no refino secundário, a absorção de inclusões pela escória é umas das principais formas de se obter aços com maior limpeza inclusionária, e consequentemente, mais nobres. O presente trabalho tem como objetivo a caracterização de fases de escórias de refino secundário do sistema CMAS (CaO, MgO, Al2O3, SiO2), a fim de se obter informações a respeito de sua composição e fração líquida, além de prováveis fases sólidas. Para isso, quatro amostras de diferentes composições químicas foram fundidas em forno elétrico resistivo a altas temperaturas. As amostras também foram analisadas por diferentes técnicas como: microscopia eletrônica de varredura com sistema EDS acoplado (MEV/EDS), difração de raios X e simulação termodinâmica. Os resultados obtidos experimentalmente foram condizentes com as simulações termodinâmicas e com os resultados encontrados na literatura.

Aug 16, 2017

By Chris Doyle

From 1997-2000. PT INCO undertook the Fourth Line Expansion Project (FLEX) to increase annual production rates from 90-100 to 150 Mlbs Ni/year (68,000 MT Ni/yr). In 2003, PT INCO nickel production underwent a major sustainable step jump that finally exceeded the targeted rate. This paper presents the changes that led to this achievement. The focus of mining changed. Improving Ni grade was important but only if electric furnace feed met target chemistry so that on-specification slag could be produced. The intensity of diamond core drilling for exploration was dramatically upgraded, mine planning strategy was totally re- vamped and an ore chemistry quality assurance team was formed. In the processing plant, measurement systems were upgraded for better control. Teamwork between sections vastly improved. The final step jump in production occurred when the fifth hydro-electric power generator was added to the furnace grid to allow the power-starved furnaces to cruise in operation at 70+ MW. Keywords: Free cash flow, Ore Chemistry, Measure, Control, Improve

Jan 1, 2004

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do Alto Forno está bastante ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas, especialmente, do coque. O desafio da produção de coque está em projetar misturas de carvões que produzam coque a custo baixo e com elevada qualidade. Neste contexto, este trabalho visa avaliar a utilização de moinha de carvão vegetal na mistura de carvões reduzindo a necessidade da importação de carvões minerais, mantendo a qualidade requerida pelo Alto Forno, além de desenvolver uma rota para minimizar a emissão de CO2 proveniente do processo de obtenção de ferro gusa em Altos Fornos a coque, reduzindo seu impacto ambiental. Foram realizados testes em escala piloto com até 20% de moinha de carvão vegetal. Os resultados das análises realizadas no coque mostraram a viabilidade técnica e comercial para utilização em até 2% na carga.

Aug 17, 2017

By S. P. Singh

Drifts are the nerve centre of underground mining. They provide essential communications between primary openings and production areas. In view of their strategic importance in the overall safety, economy and productivity of mines, an empirical approach for blast design during drifting has been proposed in this paper. The approach was developed with the objective of minimum blast damage and provides computerized blasthole patterns for drifting operations. The drift blasting practices and problems in Canadian mines have also been reviewed in this paper.

Jan 1, 1991

By John P. Powell

A comprehensive study of the effects of hydraulically fracturing water-flood wells in Oklahoma has been made by the Federal Bureau of Mines. This report presents results of that study and an analysis of some of the factors governing the results of fracture treatment on waterflood properties. Originally, hydraulic fracturing was used to stimulate oil production from old wells producing by primary methods, and its application to water-flooding was regarded with skepticism by most producers. However, since 1953 the number of fracture treatments of both oil and input wells in waterfloods has increased steadily. Hydraulic-fracture treatments in waterfloods have generally been successful in stimulating production from oil wells and increasing the rate of injection into input wells. Hydraulic fracturing has enabled several producers to turn probable failures into economically successful projects.

Jan 1, 1961

By Izabelle Lannes Salgueiro Ferreira

Este trabalho teve como finalidade aumentar o índice de rendimento metálico no processo de laminação à quente de aços longos no Laminador Demag, visando reduzir as perdas metálicas com maiores impactos no processo, com foco nas barras laminadas por barras perdidas. Mediante ao cenário atual da economia brasileira, o índice do rendimento metálico no processo de laminação representa um dos maiores impacto no custo de transformação do produto acabado. Para isso dividiu se o trabalho em duas fases, com aplicação da metodologia Seis Sigmas, que consiste em atuar nos problemas de forma ordenada, através da matriz de esforço x impacto. Seis sigmas é um mecanismo utilizado em melhorias de processos em geral, como forte característica identifica os parâmetros mais relevantes e influentes na geração de perdas metálicas no processo de laminação, no qual nos norteou a elaborar um plano de ação de forma sólida, ou seja, ações com menor esforço e maior impacto com foco nas causas fundamentais. Com a implementação do plano de ação, houve um aumento de 0,72% no índice do rendimento metálico para uma produção 178kt no ano 2015, com crescente melhora na performance das barras laminadas dos produtos do laminador Demag.

Aug 17, 2017

By ALICE V. Petar

Thallium is one of the rare metals that has come into commercial use within recent years . Its comparative scarcity , combined with a resemblance to the common metal lead , have retarded the development of uses for thallium . Although production is still measured in pounds rather than in tons , it is now finding application in a number of fields . Perhaps the earliest commercial use of thallium was as a constituent of optical glass of higher refractive power than similar glasses containing lead . One of the later applications to attract attention was the use of the oxysulphide in a sensitive electrical device similar to the selenium cell . The " Thalofide " cell , which was patented in 1919 , constituted for a time the most important outlet for thallium. During the next few years the limited use of thallium and its salts in other fields was insufficient to absorb an annual production of a few hundred pounds , and the price dropped from $ 16 or $18 per pound in 1922 to $ 5 per pound in 1924 . Beginning in 1925 several new uses were developed , especially as a poison for rodents and ants , and as a result the demand for thallium increased sufficiently to cause a recovery in price to the present level of from $12 to $15 per pound .

Jun 1, 1931

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By C. Q. Cupps, R. F. Zaffarano, J. Fry

Reservoir oil analyses from seven wells in the Greater Clareton area have been included in a study of the original characteristics of oil in the Newcastle sandstone reservoir . These data correlated with areal location of the wells show an increase of saturation pressure in a general north - south or downdip direction . The increase amounts to about 500 psi in more than 17 miles , which corresponds to a depth increase of about 1,600 feet . To facilitate application of the data to engineering analyses , average characteristics are given for arbitrary north and south divisions of the 22 - mile - long producing area . The downdip increase of saturation pressure is taken as evidence of updip diffusion of solution gas from a somewhat higher concentration at the bottom of the reservoir . This effect is opposite to that previously observed in two prominent high- relief reservoirs in the Rocky Mountain area . The increasingly greater saturation pressures southward or downdip in the Greater Clareton area suggest a continuing migration of fluids into the structure .

Jan 1, 1964

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By D. E. Larson

The U. S. Bureau of Mines has developed a image analysis methodology to correlate the energy consumed during the grinding of an ore to the mineral liberation achieved. Energy consumption values are obtained using a laboratory-scale ball mill equipped with a torque sensor, and an automated image analyzer is used to determine the liberation present in ground products. By combining liberation information with energy consumption data an appraisal can be made of the energy required to liberate the mineral(s) of interest. Results of tests performed on a complex sulfide material determined the effects of grind duration on the liberation achieved and the energy efficiency.

Jan 1, 1995

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019