Search Documents

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By Adam Gerondale, David Hemstreet, Lisheng Shao, Kenji Yamasaki

"Foundation soils of a proposed single-span bridge over a busy railroad in Anchorage, Alaska included a layer of sensitive, non-plastic to low-plasticity silt. Slope stability analyses showed that, without ground improvement, the proposed abutments would not be stable immediately following the design earthquake due to the liquefaction of the sensitive silt. Wet soil mixing was selected to mitigate the liquefiable soils and assure abutment stability because: (i) it is a non-vibratory method and can be used for areas adjacent to the railroad tracks and underground utilities, as well as in areas not sensitive to vibration; and (ii) preand post-ground improvement testing, such as SPT or CPT, is not required. Eliminating the liquefaction hazard at the site also allowed for the abutments to be economically supported on shallow spread footings. A total of 511 soil-cement columns were constructed at the two abutments, each with a diameter of 8 feet (2.4 m) and an average length of 20 feet (6.1 m), extending from about 30 to 10 feet (9.1 to 3.0 m) below finished ground elevation. The columns were laid out in a shear wall pattern (in the longitudinal direction of the bridge) to increase stability under the loading by approach embankments.INTRODUCTIONAlaska Department of Transportation and Public Facilities (Alaska DOT&PF) is currently constructing West Dowling Road Overcrossing in Anchorage Alaska. It will be a single-span, steel box girder bridge approximately 200 feet (61 m) long and 100 feet (30 m) wide. It will have approach embankments, about 40 feet (12 m) high, on both sides. It will carry the new extension of West Dowling Road over double tracks of Alaska Railroad and Arctic Blvd. Foundation soils of the abutments consist of surficial fill and peat layer underlain by soft silt which is likely to liquefy and lose strength under shaking by a design earthquake. Both deep and shallow foundations were considered to support the bridge abutments. The design team pursued the option of improving the foundation soils and using shallow footings. Several ground improvement methods were evaluated, out of which wet soil mixing was selected as the best option.In situ wet soil mixing (hereinafter simply soil mixing) is mechanical mixing of soil in its location with cement slurry and produces soil-cement (soilcrete) columns that are stronger, less permeable, and less compressible than the original soil. Soil mixing is used for various applications including reinforcement of soft soils, excavation support, liquefaction mitigation, cutoff walls, etc. This paper presents a case history of soil mixing successfully used to improve foundation soils of bridge abutments to allow the use of spread footings."

Jan 1, 2015

By S. K. Jena, S. Singh, B. Das, N. Dhawan, P. K. Misra, D. S. Rao

"Iron as an impurity in pyrophyllite ore affects pottery, ceramics and tile quality. We carried out the characterization of a pyrophyllite ore sample using optical microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and wet chemical analysis. The study revealed the presence of 2.15% iron oxide (Fe2O3 ) along with silica and alumina as the major components, which constituted around 90% of the total sample. We carried out the removal of iron from the pyrophyllite using magnetic separation and acid leaching and found that wet high-intensity magnetic separation (WHIMS) could remove 28% of iron values while oxalic acid leaching could remove up to 99.3%. The leaching kinetics of iron removal and the effects of pulp density, acid concentration, leaching time and temperature were also investigated. The optimum conditions for leaching were found to be leaching time of 60 minutes, temperature of 90°C, pulp density of 5%, oxalic acid concentration of 0.3 M, and particle size below 100 microns. Iron dissolution from the pyrophyllite sample can be best described by the diffusion of ions through the product layer of constant-size spherical particles. The breakdown of the pyrophyllite structure was evident from the FTIR and TGA studies. The activation energy of the leaching process over the temperature range was calculated to be 43.47 kJ/mol. IntroductionPyrophyllite is a naturally occurring phyllosilicate mineral composed of aluminum silicate hydroxide [Al2Si4O10(OH)2] as the major component and often associated with other minerals such as kaolinite, mica, quartz, rutile and epidote. It occurs in fine-grained sericite schist that is quarried as pyrophyllite (Pandit et al., 2008). In India, pyrophyllite occurs mainly in Madhya Pradesh state, Uttar Pradesh state and the Keonjhar district of Odisha state (Harpavat, 1995). Pure pyrophyllite is a highly desirable material for various applications due to its unique properties. It exhibits high refractive behavior, low thermalelectrical conductivity, low expansion coefficient, low hot-load deformation, low bulk density and high corrosion resistance to molten metal and basic slag (Rieger, 1997). It is used in the ceramics, refractory, foundry, electrical-insulation, sanitary-ware, glassmaking, pesticide and rubber fields. Compared with clay, it has lower thermal conductivity and coefficient of expansion, making it more suitable for refractory applications (Harben, 2002; The Minerals Yearbook, 2011)."

Jan 1, 2015

By D. Shaver, M. N. Badonie, J. Newcomer, V. T. McLemore, E. Owen

Rare earth elements and critical minerals have recently become of great economic interest because of their necessity for many new technologies and recent geopolitical unrest affecting the supply and import of resources. The San Juan and Raton basins in northern New Mexico are two structural coal basins that contain elevated concentrations of rare earth elements and critical minerals. These two New Mexican coal basins will be assessed geochemically and petrographically to identify vectors of the rare earth element and critical mineral enrichment. Coalbeds, coal seams, overlying, and underlying rock units will be sampled and characterized to determine any economic viability. Historic data will be compiled into a new and comprehensive coal geochemical database, which will grow with new analyses, and serve as the dataset for this project; this coal resource database will be made available to the public.

Feb 1, 2023

By Ramiro da Conceição do Nascimento Júnior

O uso de minérios lateríticos na metalurgia extrativa do níquel tem demandado investimentos em pesquisa e acordos de cooperação técnica para o desenvolvimento de tecnologias mais econômicas e produtivas. Devido às características de difícil processamento do minério e pelo decréscimo da sua quantidade e qualidade, ressalta-se a necessidade de se determinar técnicas efetivas de concentração, que possibilitem o aproveitamento de minérios marginais finos. Estabelece-se então, dentro de uma rota de processamento proposta, a estratégia de se produzir aglomerados (pelotas e/ou briquetes) a partir de concentrado de níquel. Além da fabricação dos aglomerados, faz-se necessária a sua caracterização em uma série de ensaios, para servir de base para a certificação desse produto e sua aplicação em processos de obtenção de ferro níquel ou gusa enriquecido com níquel. Um dos ensaios realizados envolve a caracterização física desses aglomerados. O ensaio foi realizado em máquina universal de ensaios, observando-se a resistência à compressão de amostras de aglomerados que passaram por diferentes tipos de rotas de processamento, e de diferentes etapas do processo de pelotização. Os resultados mostram que os aglomerados submetidos ao ensaio possuem resistência à compressão de pelotas verdes e secas de minério de ferro, conforme o esperado.

Aug 17, 2017

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By G. K. Burgess

(New York Meeting, October, 1913.) 1. COOLING AND HEATING CURVES BY G. V. BURGESS AND J. J. CROWE. § 22. THE results published in Professor Howe's paper 10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels 11 containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by' the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to -0.1 sec. for recording .time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain's derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12. The observations were taken in vacuo on cylinders 5/8 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thereto-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by, platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 6, 1913

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By Antônio Augusto de Morais Piau, Miguel Araujo de Vasconcelos Filho, Bruno Mynelly Galdino de Sousa

Sludges and dusts generated by steel mills usually cause environmental problems and has a high cost solution. This presentation offers a different aproach to the problem with a solution that not only solves the enviromental issue but also brings great savings to the mill. This technology, reuses dusts and sludges in the sintering process, after they are mixed to the right composition.

Oct 1, 2019

By K. J. Liles

The Federal Bureau of Mines conducts a comprehensive test program on clay and shale at the Tuscaloosa Metallurgy Research Center. All samples are subjected to standard preliminary ceramic tests, which include firing formed briquets at temperatures ranging from 1,000° to 1,250° C to identify firing range and colors, and quick-firing to determine bloating characteristics. Materials that shop potential as structural products are further tested after either extrusion or dry-pressing. If the quick-fire test is positive, bulk samples can be fired in a rotary kiln to evaluate their potential as light- weight aggregate A number of miscellaneous tests also can be conducted if requested. These tests determine properties such as refractoriness (pyrometric cone equivalency), oil-bleaching characteristics, oil absorbency, viscosity for drilling-mud applications, sand-bonding properties for foundry usage, and pelletizing characteristics.

Jan 1, 1977

By Kenneth H. Johnston

This report describes an in situ combustion project and three waterflood projects in Allen, Anderson, and Wilson Counties, Kansas, that will be visited during the 1964 annual tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the movement of heavy crude oil through the reservoir and into the wellbore with energy furnished by burning s portion of the crude oil therein. Another feature is the simultaneous injection of C02 and water, through separate tubing into input wells during early development, to increase injectivity at moderate pressures, Discussion of individual projects includes information on their early history, source and treatment of injection fluids, oil production-decline curves, and the results of water injection on oil production.

Jan 1, 1964

By S. N. Monteiro, C. M. F. Vieira, A. P. N. M. de Sa, J. P. D. Vitorino

"This work has as its objective to characterize an ash waste and to evaluate its incorporation into a clay to produce bricks and roofing tiles. The waste is a type of fly-ash resulting from the incineration of a selected part of urban garbage, which is basically constituted of organic matter and plastics. The waste was submitted to mineralogical and chemical characterization. Compositions were prepared with incorporation of the waste in amounts of up to 20wt.% into athe clay. Rectangular specimens were prepared by extrusion and fired in a laboratory furnace at 900°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste is predominantly composed of quartz and calcium compounds. The incorporation of the ash was deleterious to the evaluated properties of the clay. It is suggested that the incorporation should be made in amounts below 5wt. % to avoid deleterious effect in the mechanical strength and water absorption of the clayey ceramic.IntroductionThe world attention has turned to a subject of great concern today, the production and disposal of large amounts of industrial wastes as well as wastes of various sources. When deposed in an unsuitable place, these wastes can cause considerable harm to human health and to the environment. Our planet suffers with air pollution, groundwater and soil contamination as well as silting of rivers and lakes with the growing amounts of our society wastes.The recycling of waste materials is of great interest to the industries, mainly due to the environmental agencies legislation. One of the practices for correct disposal of these wastes being investigated is to incorporate into red ceramics, such as bricks and roofing tiles. The natural variability of the characteristics of the clays associated with the relatively simple processing techniques and also the low performance required for the products allow the presence of relatively high levels of impurities in clayey ceramics."

Jan 1, 2011

By W. C. Hagel, J. H. Westbrook

Usittg a sectioning technique with Agl10 as the tracer, the diffusion of silver in silver-excess (45.8 at. pct Mg), near-stoichiometric (49.8 at. pct Mg), and magnesium-excess (52.0 at. pct Mg) cylinders of CsCl-type AgMg was determined from 500" to 700°C. Diffusion coefficients conform to the expression D = Do exp (-q/RT) where the respective Do values are 1.53, 0.280, and 0.134 sq cm sec-I and the Q values are 41.3, 40.6, and 38.0 kcal g-atom-'. Lnttice-parameter and density measurements were performed on a more numerous assortment and wider range of compositions. Substitutional defects were found on both sides of stoichiometry. Activation energies for other rate processes in these alloys show related trends with changing composition, although silver may not be the rate-detemining species. KNOWLEDGE of diffusion coefficients is necessary for a quantitative understanding of the many rate processes (e.g., grain growth, precipitation, sintering, oxidation, or mechanical deformation) occurring in solids. Although these data are available for most metals and common alloys, they are quite limited for intermetallic compounds—a group of materials whose unique physical and mechanical properties are presently attracting great interest. From a fundamental viewpoint, diffusion in intermetallic compounds also offers several engaging aspects owing to: their ordering, the possibility of introducing large, stable concentrations of lattice defects, and the variety of bonding types and crystal structures which can be found. In the case of CsC1-type compounds, some previous work has been directed at examining the role of vacancy defects by changing their concentration compositionally. The diffusion of Co60 was measured in 0 NiAl1- and in P COA., Except for the results of Smoluchowski and Burgess, isothermal diffusion coefficients were found to pass through a minimum at the stoichiometric composi- they decreased sharply on what was reported by Bradley and co-wrkers' to be the vacancy-rich (aluminum excess) side of stoichiometry. This investigation of the diffusion of Agl110 in AgMg was undertaken both as an adjunct to a concurrent study of its deformation behavior and for the purpose of obtaining information on the influence of lattice defects and temperature on diffusion in another CsC1-type intermetallic compound. Bcc AgMg remains ordered up to and melts congruently at 820°C. Solubility limits at 300°C are about 41 at. pct Mg and 53 at. pct Mg. It is one of the Hume-Rothery electron compounds with a 3/2 electron-atom ratio. Previous investigations of its properties include hardress,' tenile,'-' electrical reistivity, and thermodyna-mic1',14 studies. Indications of a high bonding strength may be found in the large heat of mixing1' and in the 6-pct vol contraction on compound formaticp, as calculated using atomic radii of l.40 and l.55a for Ag and Mg. EXPERIMENTAL PROCEDURE Alloys were prepared by the induction melting of selected fine silver (99.95) and low-iron magnesium (99.95) in magnesia crucibles under 1 atm of A. Supplied by the Handy and Harmon and Dow Chemical Cos., respectivelv. Melts were poured under argon into graphite molds providing 1 1/8-in.-diarn. by 4-in.-long ingots. These were homogenized in evacuated and argon-filled fused-silica capsules by heating for 16 hr at 750'. Three 1 in.-diam. by 3/4-in.-long cylinders were machined from the mid-portion of each ingot for diffusion measurements. Three alloys, analyzing 45.8, 49.8, and 52.0 at. pct Mg were taken as representing the extremes of interest, with 49.8 at. pct Mg being very close to the stoichiometric composition of 50.0 at. pct Mg.

Jan 1, 1962

By A. C. Rice

Aminopolyacetic acid chelating agents were added to separatory-funnel-scale solvent-extraction systems to determine the effect on separating rare-earth elements. Average values for separation factors between adjacent elements obtained with Primene JM-T2 increase 36 percent when EDTA is added to the aqueous phase. Adding HEDTA or DCTA also improves separation factors for certain rare-earth elements. Percentage of extraction and the separation factors exhibit marked sensitivity to concentrations of amine, chelating agent, and hydrogen ion. The chelating agents improved separation in Primene JM-T, BHDA, and Primene 81-R extraction systems.

Jan 1, 1963

The Institute has no available copies of Bulletin No. 7, January, 1906, and Bulletin No. 105, September, 191.5. The sum of 30.50 per copy will be paid for these Bulletins.

Jan 6, 1917

By Bertrand L. Johnson

Langbeinite, a comparatively rare mineral that has been reported from only five countries in the entire world, has recently attained considerable economic importance in the United States and Poland. Since September 1940, several hundred thousand tons have been produced in one of the Carlsbad (N. Mex.), potash mines for chemical and fertilizer use. As it is a newcomer in this field, and as it is the source of fertilizers possessing special advantages, notably for soils deficient in magnesium or requiring sulfate fertilizers, a discussion of its properties, occurrences, uses, mining, and treatment is appropriate at this

Jan 1, 1944

A number of terrane reconstructions conflict with global plate histories or with data from adjacent regional studies. Paleogeographic maps have ignored terranes thus are over-simplified. This paper represents an attempt to "marry" Mesozoic global plate reconstructions and terrane analysis to produce examples of a "third generation" of global plate tectonic maps. The best approach to global terrane analysis involves intercomparison of all regional data and the evolving global model. Data conflicts within and between terranes and regions must be resolved by a system of relative data reliability "weighting." The most reliable and useful data are those which constrain "departure" (rift) and "arrival" (collision) times. Certain ad hoc decisions aid in the analysis (e.g. only one net vector allowed per plate). The maps that follow summarize Early Mesozoic global tectonic history at three critical junctures: 240 MA (Triassic); 180 MA (Jurassic); and 120 MA (Cretaceous). Due to space limitations, maps drawn at 20 m.y. intervals appear elsewhere. A preliminary Middle Triassic reconstruction is presented in Figure 1. Major plates and continental blocks are labeled; smaller blocks are marked with abbreviations. Examination of Figure 1 indicates the necessity of modeling Triassic tectonics with at least 68 blocks. Spalling- off of microcontinental slivers from Gondwanaland is active some 70 m.y. before the actual breakup of the supercontinent. In the SW sector of the Pacific, the Australian margins were embroidered with several terranes (e.g. Sumba) which eventually rifted away and crossed Tethys. The NW sector at this time included 10 microcontinental chips forming a huge archipelago along the Asian margin. All blocks inboard of Indochina collided by latest Triassic. Terranes of the NE sector include several (e.g. Arctic Alaska) along the North American margin, and at least six large blocks (e.g. Stikinia) drifting SE with the Farallon Plate. The SE sector

Jan 1, 1987

By T. H. Miller

This piper is a continuation of a series of yearly review articles started in 1925 by Thomas Varley. The development of flotation has been rapid, and better understanding of the functions o' flotation reagents has resulted in many changes in the kinds and quantities o reagents used. It is the purpose of this report to present the information in such a manner as to be of value to the milling industry as well as to the manufacturer of flotation reagents. These data have been compiled from a. survey of approximately 250 flotation plants of all classes within the United States. Many of these plants made complete reports of their operations, out others were apparently unable to supply this information in sufficient detail to meet the requirements of this investigation. Although it is realized that the data obtained in this survey are not as full as they should be to render the greatest service possible to the milling industry, it is hoped that succeeding articles will include complete information regarding milling; conditions and recoveries. As in the past, every effort has been made to conceal individual plant operations. RESULTS OF INVESTIGATION Table 1 gives the tons of ore treated by gravity and flotation methods and the concentrates produced as reported by 208 plants. The totals of 77,043,535 tons of ore and 4, 596,640 tons of concentrates from this table compare with totals of 78,973,012 tons and 4,683,972 tons respectively (furnished by the Bureau of Mines, Division of Mineral Statistics), indicating that the milling survey is about 98 per cant complete.

Jan 1, 1930

By M. D. Monroe

Getting the best match between truck and haul road requires examination of many factors and their effect on the bottom line. Most mines use a bottom line measure based in some way on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. Productivity can be measured or predicted for specific tasks using either field measurement or modelling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture as they are time and task oriented and can be influenced by a summation of factors over a truck lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods of time. Other cost, such as fuel and tires can be tied more directly to certain tasks such as fuel and tire cost. This paper focuses on the more direct, task-oriented factors that affect truck productivity and cost.

Jan 1, 1992