Search Documents

By J. A. Barsin

Stationary air pollutant sources established prior to the New Source Performance Standard (NSPS) are not, at present, subject to federal emissions regulations. However, proposed legislation could require many existing stationary sources to reduce emissions. This paper will report upon the laboratory work undertaken to date by B&W to commercialize a limestone system for sulfur capture both in pulverized coal and cyclone coal-fired utility boilers. Updates will be provided on the US EPA/State of Ohio/Ohio Edison/B&W sponsored pulverized coal full-scale limestone injection demonstration, and on the EPRI/Baltimore Gas 8 Electric, Atlantic Electric/B&W sponsored laboratory-scale cyclone coal limestone injection investigations.

Jan 1, 1986

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By Huimin Lu, Min Li, Jinghua Zou

"Zeolitic imidazolate frameworks (ZIFs) are new type of porous materials, form inerratic polyhedral in three-dimensional with large cages and small apertures, and appear structural diversity. Their hole size can be adjusted. These materials have high selective adsorption capacity to carbon dioxide. In this paper, zeolitic imidazolate frameworks were synthesized by solvothermal synthesis method with dimethylformamide (DMF) as solvent and structuredirecting agent, divalent metallic ions as cation, and imidazole as ligand. The crystals were characterized with XRD, SEM for their crystal structures and physical properties, the adsorption of the crystals for carbon dioxide was also tested, and the result suggests that these porous materials have a capacity of 1.35ml/g for storing carbon dioxide at 273 Kelvin under ambient pressure.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the main environment problems, contemporary research has focused on ways to slow or stop this trend. CO2 capture has attracted attention due to the potential to trap and sequester large amounts of CO2 from concentrated sources such as power plants [1]. Traditional technologies in capturing CO2 include absorption by aqueous amines [2]. However, utilization of this process is energy intensive and expensive. Carbon dioxide storage materials investigated so far can be divided into two categories: chemical storage adsorbents and physical storage media [3]. The first kind of materials can chemically adsorb carbon dioxide within their structures and need thermal energy to release the adsorbed carbon dioxide. The examples of the chemical adsorbents include aqueous amines, gas-hyperbranched aminosilicas [4]. The physical adsorbents store carbon dioxide by physical adsorption of carbon dioxide at elevated pressure and release the adsorbed carbon dioxide at low pressure. The physical adsorbents that have been investigated for carbon dioxide storage include zeolites, carbonaceous materials and other porous materials. Until recently, a new type of microporous material, known as zeolitic imidazolate frameworks (ZIFs), has been reported as promising adsorbents for carbon dioxide storage [5 ~ 10]."

Jan 1, 2010

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

By J P. Richards, M D. Johnston

The Porgera gold mine, located in the highlands of Papua New Guinea, produced 7.7 Moz of gold between 1990 and 1998. Reserves are estimated to be 12 Moz of Au. The deposit is associated with 6 Ma-old mafic alkalic intrusions emplaced at shallow levels into unconsolidated Jurassic and Cretaceous sediments, where they caused the formation of peperites. The mineralisation consists of an earlier base-metal-sulphide-rich stage with sericite-carbonate alteration (stage I), and a later phase represented by quartz-roscoelite veins (stage II). New styles of mineralisation and alteration have been recognised at depth in association with stage I. They consist of the assemblages magnetite-chalcopyrite-pyrrhotite and biotite-actinolite-anhydrite respectively. In addition, the recent recognition of adularia in some stage II veins (with roscoelite) confirms the similarity of this style of mineralisation with other adularia-sericite or low-sulphidation epithermal deposits.

Jan 1, 1999

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N&apos;Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N&apos;Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center&apos;s myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By GLADYS G. HEFFNER, William H. Waggaman, Edwin A. Gee

Thallium is one of the rare and relatively neglected elements that has recently assumed conspicuous importance. This element is widely distributed in nature but occurs in such minute quantities in most rocks and minerals that its recovery at present is only commercially feasible as a byproduct of other industries. World War II, with its unprecedented demand for products having special or unusual properties, led to a study of a number of the rarer elements that previously had been given comparatively little attention for one or more of the following reasons: 1. 2. Limited knowledge of properties. Small quantitios present in available raw materials. 3. High cost of concentration and recovery. Some of those rare elements, either alone or in the form of compounds, have already proved of such value for certain military and industrial purposes that their extraction from ores and waste products, oven at high cost, is fully justified. On the othor hand, further investigation of their character- istics, discovery of more adequato sources, and improvement in methods of con- centration and recovery would greatly broaden their field of usefulness and establish new and expanded industries. The current market for some of these elements exceeds the available supply. One of the functions of the Bureau of Mines is to study the properties of such elements in greater detail, locate the most promising raw materials from which they can be derived, and work out methods of extraction that will render the recovery of such elements more economical. The purpose of a serios of information circulars on the raror elements is to present in condensed form the facts and data so far available. This information may serve as a basis in planning more complete investigations loading to a full utilization of such elements.

Mar 1, 1950

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau&apos;s Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960&apos;s was done on coking coals.

Jan 1, 1981

By J. E. Urosek

The Mine safety and Health Administration (MSHA) formed the Mine Ventilation Bleeder and Gob Training Committee in 1993. This committee was charged with developing a training course designed to enhance the knowledge and understanding of practical bleeder ventilation systems. The course will probably include a discussion on the theory behind bleeder system design, an in-depth look at the strengths and weaknesses of the basic bleeder system types, case studies, and a review of the systems currently in use. A database on active underground bituminous coal mines, gob areas, and the bleeder systems presently used was developed from questionnaires distributed to nine Coal Mine Safety and Health (CMS&H) districts. Representative systems were selected for thorough investigation to develop case studies. This paper introduces some of the material to be included in the course, including a description of basic bleeder system designs, a review of a portion of the database, and facts about the gob areas and bleeder systems investigated for the development of case studies.

Jan 1, 1995

By G. S. Rice, R. V. Wheeler

"FOREWORDThe cooperative mine safety research program was carried on successfully in the year 1930 in a manner similar to that described in the report for 1929It is believed that the results of such fundamental work as is being done are unquestionably of great benefit in their application in coal-mining operations, in the saving of life and health of minera. The research result compared and checked by investigations in the two organizations, and further by large-scale tests, as in the Experimental Mine, give confidence to mine operators, miners and State mining officials in the findings of the various researches.The annual report of the contact officers of the United. States Bureau of Mines and the British Safety in Mines Research Board to the Director of the Bureau and the Chairman of the Board respectively, follows:Annual Reports for 1930 To: The Director, Bureau of Mines.The Chairman, Safety in Mines Research Board."

Sep 1, 1931

By André Xavier, Edim Bahamonde

En las últimas décadas ha habido un aumento del otorgamiento de concesiones mineras por parte del Estado peruano; sin embargo, paralelamente se ha incrementado el número de conflictos sociales. Ante este panorama, es necesario promover la participación de las comunidades a través de la conformación de comités de monitoreo ambiental participativo, como una herramienta que fortalezca las relaciones de confianza entre las empresas mineras, las comunidades y el Estado, de manera que se genere progreso en la línea de los Objetivos de Desarrollo Sostenible. Este estudio presenta los casos de los comités de monitoreo ambiental participativo de Orcopampa (Arequipa), Juprog (Ancash) y Mallay (Lima), como referentes de buenas prácticas que aportan al mejoramiento de la prevención de conflictos socioambientales.

Sep 20, 2019

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

Discussions of the paper of Mr. Gayley read by title at the Lake Superior hieeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 746). With the exception of Mr. Pourcel&apos;s discussion (p. 1038), these papers are here published under a mutual agreement between the Councils of the two Institutes, and will also be found, with others, in the Journal of the Iron and Steel In-slitute for the pear 1904, Mr. E. Windsor Richards, Past-President,&apos; said that in 1799 Mr. Dawson, of Low Moor, read a paper before a scientific society in York pointing out the great diff&apos;erence in the moisture of the air going into the blast-furnace in the hot months of the year and in the winter months. A cold blast-furnace was a very sensitive instrument, and showed this very clearly, for in June, July and August the furnace did not drive so well; it did not make the quality of iron and required more fuel; so that Mr. Gayley was on the right road to effect an enormous improvement in this direction. He considered that Mr. Gayley was on the way to great success, and hoped that the apparatus would not be a very expensive one. He supposed it mas too early for Mr. Gayley to let them know what the saviug was

Jan 1, 1905

By André Luis Martins de Souza

O objetivo do estudo foi medir e aumentar a produtividade das equipes de manutenção - em uma mineradora multinacional - dentro e fora das paradas de manutenção, avaliando os principais fatores que influenciam o indicador e, ainda, reduzir os custos de manutenção referente a contratação de efetivo terceirizado através da inovadora metodologia Six Sigma, para este trabalho utilizou-se um metodo quantitativo, analítico e experimental. Após a finalização do projeto obteve-se o aumento da produtividade da equipe de manutenção em todos os turnos analisados e os custos foram reduzidos em aproximadamente R$ 200.000,00 e o tempo para resolver pendências que era de 50,1 dias foi reduzido para 18,1 dias.

Oct 30, 2017