Search Documents

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By Juver Vélez

Este método de exploración consiste en la introducción con un equipo mecánico - hidráulico que ejerce presión y rotación sobre un tubo de metal el cual tiene en su inicio una corona con diamantes impregnados (denominada broca), al interior de la corteza terrestre, con el objetivo de extraer el material roca de profundidades a la superficie para realizar su identificación geológica y análisis varios; La perforación diamantina ha venido desarrollándose a través del tiempo y con la experiencia de los operadores, llegando a crear máquinas de gran capacidad para alcanzar grandes longitudes.

Sep 1, 2017

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By Paulo von Krüger

Nas condições adversas do mercado atual, aliadas à exacerbada competição é uma questão de sobrevivência a otimização de resultados. Para tal é imprescindível que os principais insumos, particularmente os mais gravosos sejam criteriosamente selecionados. Os eletrodos de grafite estão entre os itens principais na operação dos fornos elétricos a arco, tanto do ponto de vista técnico, quanto econômico e a escolha correta deste insumo deve contemplar aqueles dois enfoques. Esta escolha se faz dentre as diversas classes, disponibilizadas no mercado: RP, HP, SHP, UHP. O que se pretende no presente trabalho é sugerir uma metodologia que, contemplando o elenco de parâmetros influentes, permita fazer a escolha correta do eletrodo, dentro daquelas classes, tanto sob o enfoque técnico, quanto econômico.

Aug 17, 2017

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By John C. Feeley

The methods used and the funds available for the development and oper- ation of shall mines and the reopening of small abandoned mines frequently present problems that tax the ingenuity and resourcefulness of the mining engineer far beyond that required in the mass production from large deposits. The objective of this paper is to describe in considerable detail the means whereby engineers have solved local problems in reopening an abandoned mine at which equipment, facilities, and funds were limited... The Etowah Coal & Iron Co. Gadsden red-iron-ore mine at Gadsden, Ala., 18 of interest in this category since it is the only independent red-ore mine under active development in the State. All other red-ore mines in Alabama are owned or controlled by the large iron or steel companies. The The mine, located on the southwest end of Shinbone Ridge in the outskirts of Gadsden lies in an ares once productive. but now idle, for many years. ore is relatively highgrade compared with that in the Birmingham area, but the bed is thin and somewhat lenticular. The presence of a large blast furnace at Alabama City, 3 miles from Gadsden, and the growing scarcity of red-iron ore supplies for it offered inducements for reopening the mine in 1946. Up to the time this circular was prepared (1947) only a small quantity of ore (about 1,500 tons) has been produced and shipped to the furnace. A force of 14 men was employed in sinking the main slope and developing a third "lift" (a local term for level) 100 feet below the old mine workings.

May 1, 1949

By L. Frost

Physical Conditions Great Britain The physical conditions in the mines investigated in Great Britain are similar to those found in the mines of the Dominion Steel and Coal Corporation, with the important difference that many of the coal seams visited were interspersed by a large number of heavy faults, making the development of a continuous face operation difficult, and in many cases the life of a unit development was exceptionally short, adding to unit cost; but in spite of these difficulties, a great deal has been accomplished in the application of mechanical loading units in a number of the mines in the areas visited. The coal-bearing measures, as in Nova Scotia, consist of shales and sandstones, and in some sections mussel bands overlie the coal seams making roof conditions difficult'. In several mines, the main roof consisted of weak shale bind, being held by a coal roof of varying thickness. This shale bind had a tendency to flow when the coal roof was broken. The floor, in some cases where cutter loaders were operated successfully, consisted of weak, flaky shales with very little resistance and a tendency to disintegrate into powder when broken. The depth of cover under which these mines were operating varied from 250 feet to 2,340 feet, with an average of 1,700 feet. The coal seams varied in height from 3 feet to 8 feet 6 inches, and the gradients from level to 33 per cent. The seams vary in hardness, but all-with the exception of one seam, the 'Morrison Busty'- presented a cutting problem similar to that found in Nova Scotia. The structure and cleavage of the coal was well defined and uniform. Some of the seams visited were gassy, ?but the temperature of the workings generally was not in excess of 70°F.

Jan 1, 1948

By Rachel Bauer, Jacob Henderson, Dr. Catherine Johnson

Capital Quarries in Owensville, Missouri faces several challenges when designing a blast that allows for ease of movement while maintaining controlled throw and compliant air over pressure. The primary challenge is the nearest non-owned structure (NNOS) is a residential home located 250 feet from the quarry. Another challenge is a production bench which is 100 feet tall and separated from the NNOS by Pennsylvanian fire clay that filters out high frequency waves from the blast. Material from the blast must also be less than 5 inches in order to be processed by the crusher in the quarry. To provide as much relief as possible, production shots will consist of a single row with the minimum required burden. To design the shot, signature hole analysis was used to determine the optimal timing between powder columns. Electronic detonators provided an accurately timed shot to minimize the amplitude of the vibrations while maximizing the frequencies. Boretraking and 3D profiling with Renishaw laser profiler and Strayos drone photogrammetry provided an accurate burden measurement. Powder factor was kept at 1.3 tons/lb using bulk emulsion. The boreholes were split into 5 powder columns with the top of the hole firing first in order to blast to floor grade. The resulting shot produced good fragmentation and shot to floor grade. Seismograph readings showed air over pressure vibrations within legal limits. Due to this success, multiple shots will be designed using the process described.

Feb 6, 2023

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By Enrique Roy Dionisio Calderon

O presente trabalho mostra a concepção de um modelo que permite gerar uma superfície de mínimo consumo de redutor (carbono) em Altos-Fornos. No seu desenvolvimento foram consideradas as condições de equilíbrio das reações de redução, os balanços de massa e de energia e parâmetros operacionais. Sua aplicação à redução em Altos Fornos é exemplificada para situações reais, baseada em banco de dados operacionais de uma usina siderúrgica. Foi possível, a partir de planos de corte nestas superfícies, gerar diagramas binários do tipo CR-RD (Consumo de Redutor-Fração de Redução Direta), com possibilidade de serem gerados “on-line” no processo. Dentre os resultados obtidos, destaca-se a identificação de inviabilidades termodinâmicas importantes do forno. Dentre elas o modelo permitiu, através de seus “outputs” gráficos, prever e acompanhar o fenômeno de “gelada de forno”, conferindo desta forma maior segurança operacional ao processo.

Aug 17, 2017

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By R. Van A. Mills

Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effect's on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been "Freshened" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.

Jan 1, 1928

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By Maurício Gammertt Röhnelt

A pesquisa em questão trata-se do aproveitamento e aplicação da escória de aciaria elétrica, um subproduto residual do processo de refino do aço. A força propulsora para realização deste projeto está associada à utilização do resíduo: a quantidade gerada é maior que a quantidade aproveitada, uma vez que este subproduto tem como limitante de uso o fenômeno de expansão volumétrica que compromete obras de engenharia. No presente estudo, a escória foi micronizada, caracterizada e incorporada em uma matriz polimérica para obtenção de um novo produto com propriedades vedantes. Os artefatos produzidos foram submetidos a vários ensaios mecânicos, químicos e de caracterização conforme requisitado pela norma NBR 15750. Após a análise dos resultados, concluiuse que os compostos constituídos pelo resíduo apresentaram melhores propriedades vedantes que o grupo controle de referência. Além disso, verificaram-se melhores condições de processamento nos compostos com escória de aciaria micronizada. Obteve-se, portanto, um produto ecológico, mais viável economicamente, com propriedades que atendem a uma especificação. Dessa forma, difundiu-se a aplicação do resíduo para outros ramos industriais, agregando a este maior valor comercial, promovendo assim a sustentabilidade por meio da substituição de matérias-primas provenientes de recursos não renováveis pela escória de aciaria elétrica.

Aug 17, 2017

By Joseph A. Sutton, John D. Corrick

The chemistry involved in the microbial dissolution of iron and copper from such sulfide minerals as pyrite, chalcopyrite, chalcocite, cove11ite, and bornite is described. The chemical criteria used to evaluate the activity of microorganisms on these minerals were changes in pH, ferric iron produced, and oxygen consumption. In a series of experiments in which a ferrous sulfate nutrient solution was percolated over small portions of the above-mentioned copper sulfide minerals for 56 days, the iron-oxidizing bacteria Ferrobaci11us ferrooxidans and Thiobaci11us ferrooxidans were capable of bringing about the dissolution of 23.7 percent of the copper from chalcocite, 56.3 percent of the copper from cove11ite, and 29.8 percent of the copper from bornite by the microbial production of ferric sulfate which reacted with these minerals. Laboratory tests have demonstrated that pure strains of the iron-oxidizing bacteria act as catalysts to the ferrous iron being oxidized by the Oxygen of a system containing pyrite and chalcopyrite. In a series of experiments during which nutrient solution was percolated over pyrite for 70 days, the ferric iron produced by the iron-oxidizing bacteria was 112 to 120 times greater than that produced atmospherically.

Jan 1, 1964