Search Documents

[In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 17 and 23, outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of publications recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 17 and condition 2 on page 23. An explosive or a blasting device enumerated in the permissible lists of thin Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.]

Jan 1, 1941

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle&apos;s Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By Cris Sideco

This paper describes the concentration processes of the Sullivan. Concentrator, including crushing , transportation, sink-float, grinding , flotation and dewatering. Handling of hot muck has had a deleterious effect on most of the processes, resulting in significant operating problems and poorer metallurgy. These problems are described -in detail. THE SULLIVAN CONCENTRATOR is situated in Kimberley, high up in the Purcell Range of the Selkirk Mountains, at an elevation of 3,600 feet, approximately 4 miles from the Sullivan Mine (see Fig. 1). The original plant went on stream on August 23, 1923 at a designed capacity of 2,500 tons per day. This has been increased in stages to its present rated capacity of 11,000 tons per day. The latest stage was in 1949, when several major projects, including the underground crushing plant, the sink-float plant and the installation of a rod mill, were completed. Some 112,800,000 tons of ore have been treated in this concentrator to November 1975. The plant started on a 48-hour/ week schedule, but was reduced to 44 hours/week in October 1946 and down to 40 hours/week by the end of 1949. Except for a 6-month period in 1952 when the mill operated continuously, the 40-hour/week, Monday to Friday schedule was in effect.

Jan 1, 1977

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

NEARLY one hundred members of the Mining and Metallurgical Society of America and friends of Professor Peele met at dinner at the Aldine Club, New York, on the evening of April 26, to take part in the ceremonies attending the presentation of the Society&apos;s annual gold medal. This had been awarded to Professor Peele by the Society in recognition of his laborious and painstaking work as Editor-in-chief of the monu-mental "Mining Engi-neers&apos; Handbook. Carl A. Meissner acted as toastmaster. W. Y. Westervelt, a student and lifelong asso-ciate of Professor Peele, then recounted some of his friend&apos;s early exploits, be-ginning with his mining adventures in the paternal cellar, whereby the neces-sity for adequate ventilation was indelibly impressed on his mind. Graduating from the Columbia School of Mines in 1883, Robert Peele for several years followed the typical mining career, as assayer and superinten-dentatan outlying Colorado mine; mill foreman and assistant superintendent of the Silver King, in Ari-zona; in charge of a mine at Fairplay, Colo.; and superintendent for the Ore-gon Gold Mines Co., at Cornucopia. At intervals during this experience, he spent parts of four years on two mineral investigations m in Peru, Bolivia, Colombia, and Dutch Guiana. He i was called to Columbia as Adjunct Professor of Mining in 1892, and became Professor in 1904. During his sabattical leave in 1903 he travelled around the world, r stopping at some of the most important mining cen-ters, and in 1910 he renewed his acquaintance with South Africa and South America.

Jan 6, 1923

By R. Stratton-Crawley, S. W. Wilson

"Inco's Matte Separation Plant is a unique mineral processing facility having no process tailings stream. Each product is a high-grade concentrate with strict assay specifications which are defined by the downstream refining route. The most recent column application in the flowsheet, copper scavenging in the production of a high quality nickel concentrate, is described in detail. Testwork in pilot-scale columns (0.038 m, 0.051 m and 0.10 m in diameter) was used to develop a model of the copper scavenging system. This data was then used to simulate the performance of plant-scale equipment. The relationships thus established were confirmed by a series of plant tests in a 1.8 m diameter column. Column results consistently exceeded conventional cell performance. The modelling was extended to assess full plant production requirements and, as a result, a 2.1 m diameter column was specified for this application. Engineering design for this column is currently underway and the column is scheduled to be commissioned later in 1991.INTRODUCTIONMatte SeparationINCO's Matte Separation Plant is a part of the Copper Cliff Smelter complex near Sudbury Ontario. The flowsheet and the development of column flotation within it have been described previously (Feeley et al., 1987, Wilson et al., 1989). The plant feed is a synthetic Bessemer Matte from the Nickel smelter. This matte is slow cooled to promote grain growth and typically assays 46-52% Ni, 23-27% Cu. These elements are present primarily in sulphide form (Ni3S2 and Cu2S respectively) with some metallic alloy also precipitating from the sulphur deficient matte. Minor amounts of iron, precious metals, and nuisance elements are also present.The matte separation process is, in concept, relatively simple. Following magnetic removal of the metallic alloy from the feed, the flowsheet is designed to float a high grade copper concentrate from the nickel sulphide matrix. A simplified flowsheet of the process is shown in figure 1."

Jan 1, 1991

By RICKARD HANSEN

With vehicles frequently found in underground mines and tyres being a major fuel item, the risk of tyre fires will be severe underground. This study presents an in-depth analysis of tyre fires on mining vehicles to increase the knowledge of the risk, applying data from full-scale fire experiments and CFD simulations. It was found that the wheelhouse of the loader caused an increase in the flame tilt angle of approximately 10%, decreasing the flame impingement and heat flux downstream. The flame temperature of the drilling rig tyre was found to be approximately 7% higher than the loader tyre, increasing the risk of igniting adjacent fuel items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for the drilling rig case for higher flow velocities, indicating the influence of a varying wheelhouse/mudguard construction and tyre geometry on the flame tilt angle. The construction of the loader resulted in a flow behaviour, where the short distance to the front mudguard/tyre and the separation of flow directly downstream of the protruding construction led to fire gases being steered past the front mudguard/tyre. In the drilling rig case, the longer distance to the front mudguard/tyre led to fire gases being directed towards the body of the vehicle after passing the area with flow separation. An increased knowledge of the tyre fire risk on mining vehicles and mitigating measures would improve the fire safety in underground mines.

Feb 10, 2022

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By S. K. Basu, H. H. Kellogg

THE physical-chemical behavior of the system Pb-S-0 is of prime importance to the understanding of lead smelting processes, yet little accurate information is available on either equilibrium or kinetic behavior in this system. This paper is the first report of a program designed to fill gaps in our knowledge of this system. In the total ternary Pb-S-0, the region of greatest metallurgical interest is that bounded by the compositions Pb-PbS-PbS0,-PbO-Pb. Systems richer in sulfur, or richer in oxygen,* than those essentially pure SO2. This conclusion follows from the fact that all systems are in a highly reduced state, since either PbS or Pb is a constituent of all the equilibria. The content of 02, SO3, S2, S6, S8, and so forth, can be shown to be negligible compared to SO, in all such systems.* corresponding to this region can only be obtained at gas pressures exceeding 1 atm, a condition seldom met in lead smelting practice. Not only is the present study limited to condensed phases within this portion of the total system, but it is limited to temperatures at which all phases are pure solids, except for lead, which is liquid. In this limited system the following seven condensed phases are known to exist: Pb(l), PbS(c), PbO(c), PbSO,(c), PbSO,•PbO(c), PbSO4 • 2PbO(c), and PbSO, -4PbO(c). PbO exists in two crystal modifications,&apos; but only the high-temperature yellow form is considered here. Schenck and co-workers2-4 reported the compound PbSO4 3Pb0 to be stable at high temperature, but the more recent work of Lander,5 and the present work, prove that the tetra-basic sulfate, rather than the tri-basic sulfate is stable. Fig. 1 shows the composition diagram for the binary PbO-PbSO2, based primarily on the work of Lander. In this study the univariant boundaries and invariant points existing among these seven condensed phases and the gas phase have been determined. In a ternary system, the phase rule indicates that an invariant point involves the simultaneous equilibrium of five phases—four condensed phases and the gas phase. A univariant relation involves four phases—three condensed phases and the gas phase. The gas phase in the systems studied is The following stable univariant equilibria between SOz and the condensed phases were identified: (a) PbS + 7PbS04 = 4(PbSO, - PbO) + 4SO2 (b) PbS + l0(PbS04 • PbO) = 7(PbSO4- 2PbO) + 4SO2 (c) PbS + 8(PbSO4 • 2PbO) = 5(PbSO4 . 4PbO) + 4SO2 (d) Pb + PbSO, • 4PbO = 6PbO + SO2 (e) 3PbS + PbSO4 . 4PbO = 8Pb + 4SO2 (f) 3PbS + 16(PbS04 PbO) = 7(PbSO4 . 4PbO)+ 12SO2 (g) 2PbS + PbSO,2PbO = 5Pb + 3SO2 (h) Pb + 3(PbSO4 . 2PbO) = 2(PbSO,. 4PbO) + SO, Of these eight univariant equilibria, five were measured in this work (a, b, c, d, and g) and the behavior of the other three (e, f, and h) was calculated by thermodynamic analysis of the measured data. Two invariant points were found corresponding to simultaneous equilibria as follows: Point 1: PbS, PbSO4PbO, PbSO4.2PbO, PbSO, - 4PbO, and SO2 Point 2: Pb, PbS, PbSO, . 2PbO, PbSO, - 4PbO, and SO2, From the measurements it was also possible to calculate the thermodynamic properties of the three basic sulfates of lead at 298.16°K. EXPERIMENTAL Apparatus—The experimental method consisted of the measurement of the gas pressure exerted by a given reaction mixture at a given temperature. An iridium crucible was used to contain the reaction mixture. There was no evidence of attack of the iridium,* but after use at high temperature for a week

Jan 1, 1961

New Journals The following three journals may be of interest to readers: Fuel Processing Technology, Process Economics International, Speculations in Science and Technology, MM reports Report no. 2016 Analysis of the NIMROC reference samples for majorelements. Report no. 2018 Supergene aUeration of sulphide ores. II. The effect on the floatability of chalcopyrite, galena, and sphalerite. Report no. 2013 List of unrestricted NI M publications issued from 1966 to 1979. Report no. 2014 The determination by spark-source mass spectrometry, of chlorine and phosphorus in high-purity tungstic oxide. Report no. 2017 Vanadium-bearing titaniferous iron ores from the Rooiwater, Usushwana, Mambula, Kaffirskraal, and Trompsburg Igneous Complexes. Report no. 2022 The determination of thallium and indium in sulphide concentrates. Report no. 2023 Atomic-absorption spectrophotometry with hydride generation: an improved technique. Proceedings Proceedings of the Eleventh Commonwealth Mining and Metallurgical Congress, Hong Kong, 1978. London, Institution of Mining and Metallurgy, 1979. 800 pp. 35,00 or $U.S.77,00.

Jan 1, 1979

By James R. Hein, Jane Reid, Robert W. Embley, Se-Won Chang, Randolph A. Koski

"Abstract - This is the first reported occurrence of an active hydrothermal field in an oceanic fracture zone setting. The hydrothermal field occurs in a pull-apart basin within the Blanco Fracture Zone (BFZ), which has four distinct mineral deposit types: (1) barite mounds and chimneys, (2) barite stockwork breccia, (3) silica-barite beds, and (4) silica, barite, and Fe-Mn oxyhydroxide in sediments. All deposit types contain minor amounts of sulfides. In barite stockwork, silica-barite beds, and mineralized sediment, Ba, Pb, Ag, S, Au, Zn, Cu, Hg, Tl, As, Mo, Sb, U, Cd, and Cu are enriched relative to unmineralized rocks and sediments of the BFZ. Fe and Mn are not enriched in the barite stockwork or silica-barite beds, but along with P, Co, and Mg are enriched in the mineralized sediments. Silver contents in deposits of the hydrothermal field range up to 86 ppm, gold to 0.7 ppm, zinc to 3.2%, copper to 0.8%, and barium to 22%.Mineralization occurred by diffuse, low to intermediate temperature (mostly <250°C) discharge of hydrothermal fluids through pillow lavas and ponds of mixed volcaniclastic and biosiliceous sediments. Bacterial mats were mineralized by silica, barite, and minor Fe hydroxides, or less commonly, by Mn oxyhydroxides. Pervasive mineralization of bacterial mats resulted in formation of silica- barite beds. Silica precipitated from hydrothermal fluids by conductive cooling and mixing with seawater. Sulfate, U, and rare earth elements (REEs) in barite were derived from seawater, whereas the REE content of hydrothermal silica deposits and mineralized sediments is associated with the aluminosilicate detrital fraction. Fe-, Zn-, Cu-, Pb-, and Hg-sulfide minerals, Ba in barite, and Eu in all mineralized deposits were derived from hydrothermal fluids. Manganese oxides and associated elements (Co, Sb, Mo, W, Cl, and Cu) and Fe oxides and associated elements (Be, B, P, and Mo) precipitated as the result of mixing of hydrothermal fluids with seawater."

Jan 1, 1999

By D. J. Parker

Before the various States began to enact workman&apos;s compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen&apos;s compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions&apos; the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures&apos; When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Vas P. Kenyen

Introduction Autogenous, semi-autogenous, and conventional grinding circuits are used to process ores. Current emphasis, though, is towards the use of the first two systems. The reason is the generally lower initial investment required for an autogenous or semi-autogenous circuit as compared to a conventional comminution circuit. However, the effect of operating costs that will significantly affect overall comminution economics is not considered in this evaluation. About 70% of the energy in a mineral processing plant is used in the comminution circuit. Until the 1974 oil embargo, energy was relatively inexpensive. Since that time, the cost of energy has escalated 40-fold. As a result, energy cost now forms a significant portion of operating costs in comminution. According to a survey conducted by General Electric Co. (Powers, 1982), the price of electricity will continue to rise 15% to 20% per year, in spite of the current oil glut. Both autogenous and semi-autogenous grinding circuits consume more energy than the conventional comminution circuit. Higher consumption ranging from 16% to 35% has been reported in the literature (Bassarear, 1982; Gjerdrum. 1979; Betts, 1982; and Christie, 1979). Consequently, even a small increase in energy costs is likely to have a significant impact on operating costs. Therefore, the economic decision of selecting an optimal comminution circuit is important. More than ever before, it is now critical to include in the evaluation of communition circuits not only the capital costs, but also the operating costs; in particular, the expected energy cost over the life of the operation. Failure to do this may lead to a less than optimal comminution circuit. Design A comminution system should be designed only after bench-scale or pilot plant testing of a representative sample. Conventional crushing and grinding circuits can be designed on the basis of the Bond Work Index (Rowland and Kjos, 1980). Over the years, sizing of full-scale rod and ball mills from Bond Work Index data has become well established. Autogenous and semi-autogenous mills cannot be sized based on bench-scale tests. Pilot plant tests are necessary to determine the amenability of the ore, critical size buildup, and power requirements. For this study, conventional and semi-autogenous grinding circuits were designed for ore throughput of 12, 24, 36, 48, 72, and 90 kt/d (13,200, 26,400, 39,600, 52,000, 79,200, and 99,000 stpd). Rod and ball mills were scaled up on the basis of the Bond Work Index. A two-stage semi-autogenous grinding circuit was designed on the basis of pilot plant test results. In designing a grinding system, emphasis was placed on operating flexibility. The largest commercially available equipment was

Jan 10, 1984

By R. C. A. Thurston

"The lack of notch ductility in structural steel in general, and in ship plate in particular, has been the object of widespread attention in the metallurgical world since the spectacular collapse of the ill-fated S.S. Schenectady in 1943. Numerous investigations have been carried out, many new tests have been developed, and a vast amount of useful data has been published, with the result that our knowledge is now far more advanced than it was at the time of this disaster. Interest has focused largely on the medium strength steels, and the various factors which cause a normally ductile steel to behave in a brittle manner in the presence of a notch and at relatively .low temperatures have been thoroughly studied.The literature available on high-tensile steels, however, is less extensive and the present paper is intended to supplement this information. Notch toughness tests have been carried out, at the request of the R.C.N., on a high-tensile manganese steel in the form of commercial ship plate. One of the newer tests, the tear test, and the Charpy V-notch impact test, were used to examine the characteristics of plate for the construction of an ice-breaker. About 250 plates, mainly in the thickness range from 11,4 in. to 1 % in., were tested. An an-alysis of the results obtained is presented, certain aspects of the tear test are discussed, and the correlation between the two types of test is studied. On the basis of information available from casualty ships, the plates, with few exceptions, were considered to be satisfactory."

Jan 1, 1959

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By William C. Dixon

Since the mid 60&apos;s, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995