Search Documents

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By A. Adams

The quality of hafnium metal produced by the Kroll process depends upon the purity of the hafnium tetrachloride. This investigation of methods for purification of hafnium tetrachloride was undertaken to aid in producing a higher purity hafnium metal than is currently produced by the Kroll process, The quantities of metallic impurities in hafnium metal were decreased by contact with molten alkali-metal chloride salt. Contact was achieved by a semicontinuous process of bubbling gaseous hafnium tetrachloride through a molten salt bath or by a batch process, first fusing the tetrachloride with a combination of alkali chlorides and then heating the mixture to sublime the hafnium tetrachloride. Low-melting mixtures of sodium, potassium, and lithium chlorides were used to purify hafnium tetrachloride. About 30 percent of the initial hafnium tetrachloride was trapped during purification with alkali- metal chloride salts. The 95-percent confidence limits (6)4 for the amount of oxygen decrease 60 and 34.3 parts per million when the batch purification is combined with a reduction so that both take place in the same equipment,

Jan 1, 1961

By J. F. Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch mine in West Virginia, where 29 miners lost their lives. The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Feb 23, 2014

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By B. M. Davis

The uncertainty associated with a reserve estimate has generally been expressed as a subjective ranking rather than a quantitative expression of either reliability or uncertainty. These rankings of estimate reliability have taken a very nonquantitative bent as well. For example, the U.S. Securities and Exchange Commission definition of proven reserves is given as: Reserves for which (a) quantity is computed from dimensions revealed in outcrops, trenches, workings, or drill holes, grade and/or quality are computed from the results of detailed sampling and (b) the sites for inspection, sampling and measurement are spaced so closely and the geologic character is so well-defined that size, shape, depth and mineral content of reserves are well-established. (U.S. SEC, Form S-18, Item 17A)

Jan 1, 1992

By R. F. Burdyn

The inadequate use of centrifugation to economically recover solids from weighted drilling fluids reflects the need for better equipment and techniques for this putpose. Laboratory studies in the development of an improved separator are described in which an operating equation is derived and tested. Results show that the concentric cylinder geometry employed effectively separates bnrite from a suspension and that the operating equation provides a good approxinmtion for scale-up. INTRODUCTION Our current drilling technology frequently requires a high-density drilling fluid obtained by addition of barite. In the course of drilling, formation solids which are too fine to be removed either by screening or settling become suspended in the drilling fluid and gradually the volume of solids in the mud increases. The volume fraction of solids must be limited (if a satisfactory set of rheological parameters are to be maintained). A centrifugal separatorprovidesan economical way of accomplishing this. The barite recovery process can be considered as a separation of two solids. One, the light solids, composed of formation and added solids, has a specific gravity of 2.6 to 2.7; the other, barite, has a specific gravity of 4.2 to 4.3. This density difference, plus the fact that the average light-solids particle size is much smaller than the average barite particle size, permits separation by a centrifuge. In drilling fluids some of the coarse particles of the light-solids-range will settle faster than fine particles of the barite-particle range. As a result a complete separation of the two species is not possible. since the object of the process is not merely recovering the maximum amount of barite but includes as well removing the maximum amount of light solids, an optimum barite recovery efficiency exists. From a practical standpoint this optimum cannot be determined in the field for each drilling fluid system, and in practice the separation is less than optimum, with some sacrifice of barite. Drilling technology has included centrifugal separators for barite recovery for more than a decade. Results have been reported by a number of investigators indicating that the process is practical and economica1. l-4 The decision to use a centrifuge is based on economics in which direct cost savings and the indirect benefits in rig time derived from improvement of the drilling fluid are important factors. One would expect that centrifugal separation of barite from drilling fluids would significantly affect barite consumption; however, this is not the case. The Minerals Yearbook shows an annual domestic barite consumption in the drilling industry of nearly 1 million tons.5 By rough estimate there are perhaps 80 separators presently in field use. Assuming half of these in use at any one time, operating an average of four hours per day, at recovery rates averaging 3,000 Ib of barite per hour, total annual recovery is about 90,000 tons. This is less than 10 per cent of he total barite used. I conservatively estimate that barite consumption in drilling operations can be reduced by 30 per cent through greater utilization of centrifugal separators. To encourage more widespread acceptance of centrifugal separators in the drilling industry, improved equipment and techniques would be very desirable. The present paper, covering theory and results obtained from a laboratory model, is the first in a series on he development of an improved mud separator for field use. THE CONCENTRIC CYLINDER GEOMETRY AS A SEPARATING DEVICE Consider the geometry shown in Fig. 1, consisting of two concentric cylinders separated by an annular space. These are arranged so that the outer cylinder is fixed and the inner one can be rotated about its axis on shafts sealed against the ends of the outer cylinder. If the outer cylinder is fitted with openings at either end, the inner

Jan 1, 1966

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By Herman W. Sheffer

This report describes and discusses present-day leaching technology employed to recover copper from low-grade mine and dump materials derived from the exploitation of copper ore deposits in the Western United States. Illustrations of the integral parts of the leaching, precipitation, and recovery operations at several copper-producing companies are presented. Schematic drawings are included to present typical flowsheets of leaching and precipitation operations. Operational problems common to most copper leaching and precipitation plants are discussed. Areas of present and future research to improve leaching techniques are cited.

Jan 1, 1968

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.' Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

By Koji Matsubara, Yoshiaki Iguchi, Shoji Hayashi

Iron ore particles of a limonite iron ore were reduced completely with H2 at 1023K to 1273K in a fluidized bed. Then, at 973K, the formed iron was exposed to HrH2S mixtures (sulfur activity, as=0.5) for 3.6ks and carbidized with CO-H2-H2S· mixtures at 0.1 MPa. During the carbidization, the particles of about 150mg were sampled at every 600s interval. The sampled particles were analyzed by XRD and chemical analysis for C and S to evaluate the content of Fe3C, Fe5C2, Fe and free carbon. The reaction extent is defined as fo=Xfc3C +xFc5c2; x is the molar fraction of Fe in Fe3C. The carbidization curves can be fitted very well to -ln(l-f0)=g(pb T)t; g(p; T) is the carbidization rate, i.e. the carburization rate on the pore surface of reduced iron. The rate is found to be nearly proportional to the specific surface area of reduced iron, a P 0 , which decreases with increasing the reduction temperature. The value of a P 0 does not change by the carbidization and the stability of the iron carbide product in the atmosphere increases with the temperature.

Jan 1, 2000

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ore is a valuable resource due to its high content of metals essential for modern technology, including nickel, iron, and cobalt. However, extracting nickel from laterite ores is challenging due to their complex mineral composition and low nickel concentrations. This study examined the leaching behavior of pre-roasted laterite ore and the effect of roasting on leaching kinetics. The ore was roasted at temperatures of 280°C and 610°C for 3 h, followed by sulfuric acid atmospheric leaching. The results demonstrated that pre-roasting at 610°C significantly enhanced nickel leaching recovery, with up to 93% nickel successfully recovered. The leaching process of pre-roasted laterite ore was found to be controlled by diffusion through the ash layer, with activation energy values of 20.97 and 18.97 kJ/mol for laterite roasted at 280°C and 610°C, respectively. These findings indicate that pre-roasting can improve the leaching performance of laterite ore, potentially leading to more efficient and sustainable nickel extraction processes.

Feb 27, 2024

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By Yi-Hsuan Chen, Jürgen Brune, Candace S. J. Tsai, Alejandro Munoz, Connor Krause

This study highlights the significant presence of submicrometer- sized airborne particles in underground coal mines, especially around the belt conveyor drift areas. Using realtime instruments and gravimetric samplers, the assessment revealed that particle concentrations were notably higher in the belt entry compared to other locations, with a strong presence of submicrometer- and nanoparticle-sized dust. The study’s findings emphasize the importance of addressing small particle exposure, as these particles, composed of harmful substances like calcium, copper and iron, can pose serious health risks to miners. This research emphasizes the importance of improving air exposure estimation through more effective monitoring and characterization techniques to better understand and reduce workers’ exposure to hazardous airborne particles in the mining environments.

Apr 1, 2025