Search Documents

By W. G. Pariseau

"BACKGROUND Strata mechanics of three underground coal mines in central Utah were recently studied using a specialized finite element technique [1, 2, 3, 4]. The purpose of these studies was to examine relationships between mining and related seismicity. The longwall mining method was predominant, but room and pillar mining and barrier pillar mining were also used in the mines studied. In every case, high correlation between face advance and seismicity was observed. The specialized finite element technique allows for whole mine subsidence estimation at a kilometer scale and for stress concentration at a meter scale near a working face. Comparisons of observed mine subsidence with model subsidence allows for model verification and justifies detailed analysis of the evolution of stress at seam level. Yielding is expected near a longwall panel face and as the face is advanced the extent of yielding is expected to increase. The total number of element failures in a finite element mine model also increases, so a high correlation with associated seismicity, say, event count, is not so surprising. A brief review of recent coal mine studies in Utah is presented in the sequel. The procedures are given in some detail in application to trona mining. COAL MINES The analysis procedure begins with the geologic column and proceeds to specification of strata properties including elastic moduli and strengths. Joints are an integral part of the geologic model and joint set specifications include dip direction, dip, spacing, stiffness and strength. Spatial variability of strata properties in situ may be taken into account during analysis. Topography is important, especially to Utah coal mines that are developed from outcrop in regions of high relief. Mesh generation follows specification of data input. Finite element analysis is next, followed by reporting of results. In this regard, all finite element computations are based on first principles. No model “calibration” is done that involves adjusting computer input to obtain a fit to mine measurements such as subsidence profiles. Figure 1 illustrates the concept of a dual node – dual mesh finite element concept. Dual nodes are roof and floor nodes in mined areas. These nodes replace the seam. The dual mesh is a much refined mesh with displacement boundary conditions obtained from the big mesh and thus replaces the effect of mining in the region outside the dual mesh. The refined dual mesh allows for details of stress, strain and displacement near a working face of interest. Strata Properties Strata properties include elastic moduli and strengths of intact rock between joints and joint stiffness and strength for each joint set present. Both properties sets may be obtained from laboratory test data, although testing joints poses a sampling problem in the field. The statistical variability observed in laboratory test data, say, in unconfined compressive strength tests is often characterized by much variation. In fact, the coefficient of variation, ratio of standard deviation to mean, is often greater than 35 percent. When sample values are mapped back to the mine location, one may observe spatial variability as properties vary from place to place as shown in Figure 2. Spatial variability may be incorporated into a finite element analysis with probabilistic assignment of properties to elements in accordance with measured variability. The result is a more realistic model of rock in situ."

Jan 1, 2017

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

By Wolfang Ladewg

Desde enero hasta agosto de 1965 se probó un prototipo del telémetro electro-óptico EOS de VES Carl Zeiss JENA, a través de las mediciones en unos 70 días. En ese sentido, el objetivo del presente texto es determinar la exactitud de medición, así corno la constante de adición y el alcance del EOS. Para ello, se midieron distancias geodésicos a base estandard en los campos de ensayo geodésicos de Potsdarn y en una red de ensayo determinada trigonométricarnente. La medición de las distancias se realizó en tres días, empleándose un reflector de siete prismas con sus correspondientes cuñas adicionales. Mientras que en los campos de ensayo geodésicos se midieron 19 distancias entre O, 1 y 7,5 km. Las mediciones se efectuaron en un espacio de tres meses en total con diferentes números de series

Nov 1, 1970

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

By W. A. Mathews

We report on the progress of an automated mineralogical deportment of fluorine (F) in two portions of the Grasberg District for the development of metallurgical amelioration protocols for Cu sulfide concentrates. Fluorine detection limits in automated SEM technologies range from 1% (TIMA) to about 9% (QEMSCAN), however substitution in hydrophobic minerals or those reporting to concentrate is typically much lower (

Mar 2, 2022

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992

By M D. Sussman

A large number of countries in the world now have some regulation for labelling the presence of genetically modified organisms (GMO) in food. For the last ten years, ISO/TC 34/SC 16 has been providing methods, guidelines and requirements concerning the evaluation of molecular biomarkers including GMOs. This activity makes sure that stakeholders on all sides of commercial transactions are satisfied and their marketing or regulatory needs are met. Developing and maintaining a transparent, science-based environment for users of horizontal methods for molecular biomarker analysis is a high priority. Sampling and analysis of molecular biomarkers has become critically important for food and agricultural organisations developing, producing, distributing and selling genetically engineered, non-genetically engineered, identity preserved and/or organic crops and their derived products and preventing their respective destructive diseases. To aid in international harmonisation, a new work item proposal to develop an ISO type A management system standard (MSS) for organisations including laboratories using molecular biomarker analysis and sampling has been submitted to ISO/TC 34/SC 16. The purpose of this MSS is ensuring that determination of the presence, absence or quantification of a particular biomarker with a relationship to a product quality determinant, a marketing claim, a regulation or a plant pathogen is carried out under a suitable quality assurance / quality control system. This MSS will provide an overarching system to apply and manage molecular biomarker analysis and sampling for any organisation large, medium or small in a private, government or academic setting.CITATION:Sussman, M D, 2017. ISO/TC 34/SC 16 horizontal methods for molecular biomarker analysis – molecular biomarker analysis and sampling management system, in Proceedings Eighth World Conference on Sampling and Blending , pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Michael R. Brown

A facilities success or failure of doing well during a regulatory inspection is typically measured by the number and type of citations that result, and financial liability resulting from those citations. The success of a facility during an inspection depends on several factors including, the preparation prior to an inspection, behavior and activities during and inspection, and finally, action taken following the inspection. This paper contains suggestions for improving inspection results and establishing an attitude of compliance at manufacturing and mining facilities.

May 1, 2002

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By Ralph H. Nafziger

The feasibility of smelting a Ni-Co-Cr-bearing laterite ore from southern Oregon was evaluated by the Bureau of Mines. The objective was to prepare a master alloy for subsequent stainless steel production. A mixture of the ore with suitable reductants and fluxes was smelted in a 50-lb-capacity single-phase ac electric furnace under sub- merged arc conditions. The smelting tests produced a metal in which most of the nickel was concentrated. High-chromium recoveries required an excess of carbon. The resulting metal alloys contain sufficient nickel for some stainless steels. Ferrochromium additions would be required to attain suitable chromium levels. This research was conducted under the Oregon Metals Initiative in cooperation with Walter B. Freeman.

Jan 1, 1993

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986

By H. A. Guess

For a number of years I have used for the commercial wet assay of lead generally the ammonium molydate, and occa-sionally the ferrocyanide method. These well-known methods need no detailed description here. In the ore-selling and ore-buying establiahments of the West, 90 per cent. of all wet lead-assays are made by one or the other, and at least nine-tenths of this proportion by the molybdate method. A procedure so well-established must have merit; and, in

Jan 1, 1905

By B. J. Dalton

The Bureau of Mines Helium Research Center has developed a computer program for solving two-phase equilibria data for binary mixtures and for evaluating thermodynamic functions of interest, including all critical points. This computer program was used to calculate equilibrium points on the PVTu surface for the helium-nitrogen system as predicted by the Van der Waals equation of state. Numerical values are tabulated and illustrations are presented for 1,279 equilibrium points and for quantities needed to construct Ponchon diagrams. Equilibrium ratios as a function of pressure at constant temperature and of temperature at constant pressure-are also shown graphically. In addition, saturated partial molal volume and partial molal enthalpy data are given. It is shown that the Van der Waals helium-nitrogen system exhibits retro-grade condensation of the second type for liquid helium concentrations of about 0.07 mole fraction or less and pressures below about 45 atm. It is also shown that the critical point is at a -maximum value of pressure (at constant temperature) and of temperature (at constant pressure).

Jan 1, 1971

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974

By Claude W. Sill

In the course of a series of investigations on vanadium deposits of the western United States, the Bureau of Mines collected many hundreds of samples for chemical analysis. As uranium is often associated with these vanadium minerals, they were also analyzed for uranium, which was pound to be absent in a large percentage of the samples. Since the usual methods for determining uranium are laborious and time-consuming it is very desirable to have some simple qualitative test that can be applied prior to a quantitative analysis to determine whether uranium is present or absent and thus save the time and expense of applying the quantitative analysis to the large proportion of samples containing no uranium. To be acceptable, the test should be specific for cranium, sensitive enough to detect small amounts of uranium, and. simple enough to make it worthwhile to apply. The available methods for detecting uranium lacked one or more of the desired characteristics. Eventually, however, a method was worked out that satisfied all the requirements. This method is probably more specific and sensitive than the usual qualitative methods for uranium, and its simplicity and speed of application make it ideal for testing samples prior to quantitative analysis.

Jan 1, 1945

By Donald E. Ralston, A. T. Yu, Richard P. Killmeyer, Peter Phillips, R. W. Vander Laan, John N. Murphy, John R. Messineo, John Peters

Overview Coal production in the first half of 1982 remained near the high levels begun in mid-1981. Production then fell sharply during the latter part of the year due to recession-weakened demand. Even so, 1982 coal production was estimated at 756 Mt (833.4 million st), a record high that exceeded 1980's previous production record of 752.7 Mt (829.7 million st). Though 1982 coal production was substantially below industry expectations, the attained production represented a modest achievement in view of the recession's severity. In 1982, the gross national product declined 1.8%, its worst performance in 36 years. The recession, along with mild weather, improved energy efficiency, and conservation efforts caused the nation's energy use to drop 4.1%. With the iron and steel, construction, and auto industries experiencing production declines, industrial energy use fell 10.8%. The extent to which the nation's economic slump affected coal markets in 1982 varied: • total domestic coal use declined 3.4%; • exports remained strong for most of the year; • electric utility coal use declined for the first time in 25 years; • coal use at coke plants declined by one-third; and • coal use in other industrial sectors stayed surprisingly near the 1981 level. Coal Use Domestic coal use totaled 641.8 Mt (707.5 million st) in 1982,22 .9 Mt (25.2 million st) below the 1981 level. Nearly all the decline occurred at coke plants where use dropped to 37.1 Mt (40.9 million st) in 1982 from 55.3 Mt (61 million st) in 1981. The decline in all other industrial and electric utility coal markets was only 5.3 Mt (5.8 million st). Residential and commercial coal use increased 635 kt (700,000 st) to 7.3 Mt (8.1 million st) from 6.7 Mt (7.4 million st). Power generation decreased 2.3% in 1982, the first year since 1945 that output failed to increase. The decline was due to a drop in industrial demand. Electricity sales to residential, commercial, and other nonindustrial users increased slightly. But coal's competitive position stayed strong. Power generation from oil and natural gas fell 28.9% and 11.7%, respectively. Power generation from coal declined only 0.9%. Among the primary energy sources, coal fueled 53.2% of US electric power generated in 1982, compared with 52.4% in 1981. In 1982, US steel production declined to 66.1 Mt (72.9 million st), the lowest level in 50 years and down from 109.6 Mt (120.8 million st) in 1981. The reduced steel demand forced 13 coke plants to shut down. Coal Exports Coal exports in 1982 totaled 96.4 Mt (106.3 million st), 5.7 Mt (6.3 million st) less than in 1981. Despite the worldwide recession and above normal coal stockpiles in many countries, exports were higher than many expected. This showed the relatively strong US position in international coal trade. The US continued to export near-record coal tonnages despite increasingly competitive influences. These included an improvement in Australia's labor difficulties, the return of Polish coal to Western European markets, and lower oil prices. In 1982, US port facilities were improved and expanded, and more efficient methods for scheduling foreign vessels were implemented. As a result, high volume coal shipments to US ports were routinely loaded and dispatched unhampered by bottlenecks that plagued East Coast ports in 1981. Appalachian coalfield production declined 1.4% from 1981 output and 3.9% from 1980 output. The interior region of the US showed an increase of 7.8% in production. This was primarily because of a

Jan 5, 1983

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015