Search Documents

By A. Durnan

Barrick Goldstrike Mines Inc. (Goldstrike) operates a six circuit (train) pressure oxidation plant for the pretreatment of gold bearing sulfide ores. The property is located 27 miles north of Carlin, Nevada. Since the commissioning and start-up of the first circuit in 1990 until the present total plant availabilities have exceeded 90%. The discussion that follows will detail the maintenance practices employed to consistently achieve this goal.

Jan 1, 1994

By L. Sandbak

A geomechanical rock mass classification or RMR is currently being used for the evaluation of an LHD mechanized mining system versus the conventional block caving method. The successes and failures of a Panel lS-19 LHD test block on the 2315 level can be attributed to the geologic and geomechanical zonation present. Trench blasting, caving procedures, and sequencing are other factors that were also considered. Lessons learned from the P.lS-19 test block have been used to alter the design for future LHD production blocks on the 2615 level. These modifications are designed to maximize the pillar and insure an adequate draw connection.

Jan 1, 1988

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By José Brant, Douglas Torres, Rogério Navarro, Rodrigo Souza, Eduardo Brocchi

The steelmaking process requires the input of ferro-alloys to implement the adjustment of some elements composition in the final product. In the particular case of stainless steel production, the high carbon FeCr alloy stands out as one important precursor. However in the production of this material a certain quantity of fine powder with remarkable chromium and carbon content is also generated, which, in turn, could be processed through alkaline roasting in order to selectively recovery this element in a subsequent aqueous route. In the present work, this process is investigated, using excess of NaOH as oxidizing agent, and H2O2 for precipitating chromium as Cr(OH)3, which is next calcinated to Cr2O3. According to the results, the global achieved recovery has shown to be around 98%, suggesting that the proposed route can be seen as a potential process for chromium oxide production from the mentioned fine powder.

Jan 1, 2015

Achieving continued economic growth with social equity within the natural limits of the Earth's 'eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By Eduardo Christo Saltoratto

Foram realizados tratamentos térmicos de têmpera e revenimento para aumentar a tenacidade do material, aço NM87 designação 1045, uma vez que ele apresentava, no estado inicial, baixa absorção de energia. Com o material mais tenaz foi obtida uma melhor faixa de energia para cálculo das incertezas. Foram feitos corpos de prova com variações nas medidas laterais, de comprimento e profundidade do entalhe e ensaiados na temperatura ambiente para determinação das incertezas do tipo A e B. Com as incertezas determinadas pelos métodos estatísticos e não estatísticos, foram feitos ensaios, variando-se a temperatura, para obter dados de ductilidade (energia absorvida, expansão lateral e percentual de área dúctil) em relação a temperatura e com esses dados determinar-se a temperatura de transição dúctil – frágil e sua incerteza.

Aug 17, 2017

In this paper, three types of value-adding in the minerals industry are discussed: downstream processing, improving the efficiency of existing processing and increasing the knowledge base and expertise of the staff. It is shown that, while downstream processing seems to offer a good way of improving Australia's trade position, there are a number of impediments to such development, notably, limited access to the appropriate technology and overseas markets. Transport costs can also be a problem. To reverse the situation will require more positive policies by government. In the meantime, something can be done towards adding value by increasing the efficiency of existing processes. Examples are given, showing how it might be possible to make economies in reagent costs in the gold industry, how innovative technology has led to more complete processing of a tailings dump, how research might lead to an increase in the throughput in the production of synthetic rutile and how it is possible to leach selectively from gold/copper ores.

Jan 1, 1995

By Juan G. González Rojas

El presente estudio describe los resultados de exámenes sobre salud ocupacional en nueve asientos mineros del Perú, pertenecientes a los departamentos de Arequipa, Ayacucho, Cusco y Puno. El trabajo comprende dos partes: el ambiente ocupacional y el estado de salud del personal expuesto. Asi también se informa sobre la seguridad, aspectos de saneamiento básico de los campamentos (vivienda, suministro de agua, desagüe, etc.), las facilidades médicas y de bienestar al servicio del personal.

Aug 20, 1963

By R. P. Smith

The diffusivity of carbon in iron, cobalt, and alloys of 89.7 and 79.3 wt pct Co has been determined by a decarburization method for the temperature range 850° to 1100°C. The Plots of log D us 1/T for the two Fe-Co alloys are linear through the region of the Curie temperature, showing that, unlike some cases of substitutional diffusion, carbon diffusion in these alloys is not affected by electron spin order. RECENT investigations1-' have shown that for substitutional diffusion in iron the change in diffusivity with temperature does not follow an Arrhenius equation, at temperatures near the Curie temperature. Data on the diffusivity of carbon in a iron5"9 indicate that this anomaly does not exist for interstitial diffusion; however, this has not been definitely established. Since cobalt and Fe-Co alloys, 80 to 100 pct Co, have Curie temperatures in a temperature range convenient for carbon-diffusion measurements they are suitable systems for studying the relation of interstitial diffusion and the Curie temperature. EXPERIMENTAL The carbon diffusivity, D, was determined by a decarburization method. The diffusion cylinders, made from small vacuum melts of electrolytic cobalt and plastiron, were about 0.76 cm diam and 6.3 cm long. A small amount of carbon was added to each melt to keep the oxygen content as low as possible. The cylinders were first treated with a hydrogen-3 pct water vapor mixture at 1100°C to constant weight, then carburized to the desired initial carbon content with a suitable CO-C02 gas mix-

Jan 1, 1964

By J Zhou

This paper discusses the implementation of a mixed integer linear programming model for a coal preparation plant. The plant considered consists of primary and secondary heavy media cyclones, hydrocyclones for intermediate fines and froth flotation for the very fine material. The model is designed to optimise the plant settings and product flows to maximise revenues for a given specification for two product outputs. The model can deal with bonus/penalty aspects of the product pricing for products that exceed or fail to meet specification. We report on a model with two separate coal feeds with parallel circuits for the oversize, intermediate and fines streams. The genesis of this model is more than 30 years old but recent improvements in mixed integer programming solvers make a full mixed integer formulation practical. The original model began as an enumeration of cut points with arbitrary rules for product allocation. The product allocation was improved in a linear programming formulation by Gunn (1982) and Sarker (1991 and 1995). Current mixed integer programming capabilities make it possible to replace the enumeration aspects and solve directly as a mixed integer programming problem. The current implementation uses a general purpose modelling language to formulate the model. Open source and commercial mixed integer programming solvers are compared

Sep 26, 2011

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

'T. C. MERRIMAN, New Haven, Conn. (written discussion *).-This most interesting paper gives much carefully obtained and valuable data. However, there are two points in connection with the commercial application of such data that might possibly be a source of trouble and mis-understanding. In the first place, the examination of thin sections of annealed brass, subjected to standard Brinell test.(500 kg. on a 10-mm. diameter ball) at thicknesses from 0.075 to 0.150 in. (1.9 to 3.8 mm.) indicates that cold work has been performed on the specimen during the application of the load sufficient to extend way through the section, and have the hardness of the metal affected by the backing. If the usual steel support is used, this effect is very evident. If a piece of soft brass is used as a support, there is an indentation in the surface of the support accompanied by a bulge on the under side of the tested specimen opposite the impression made by the 10-mm. ball. The result is that Brinell specifications (governmental or otherwise) on stock for a certain purpose may not be fair in all cases, since manufacturers, owing to differences in equipment, etc., may not all use precisely the thickness and conditions of stock on which the Brinell specifications were based. This would mean that the government Brinell specification might not give them the temper of stock best suited for their manufacturing methods. The concluding paragraph of this paper, stating that "the hardness of cartridge brass may be determined with greater accuracy by the Brinell hardness measurement than by attempting to judge it from the grain size" appears to be in line with the movement of the last year or so among brass manufacturers toward substitution of the Brinell test for microscopic examination as an acceptance test on cartridge brass. The statement may he strictly true that the Brinell test is the best test for hardness, but it is not, as the statement might readily be construed, a sufficient test of suitable condition. For instance, some cartridge brass might accidentally have been overheated to a point where it would be distinctly unsafe to use for the manufacture of small arms cases and then be so rolled (reduction 3 to 5 per cent.) as to pass perfectly proper Brinell specifications. Under such conditions the microscope would reveal its unsuitability where the Brinell test had failed so to do.

Jan 4, 1919

By Sean Cassady, Jason Liu, Sanja Zlatanic, Taehyun Moon, Chris Devery

"For the Hollywood International Airport Runway Expansion Project at Fort Lauderdale, Florida, the structural fire durability analysis was completed for a series of tunnels formed by roadway and railroad cells located under the runway structure. A systematic design approach was developed to mitigate structural damage during a fire event and arrive at a practical method to structural fire engineering that is compliant to NFPA 502. To ensure the NFPA 502 requirements are satisfied, the performance based approach was implemented and the engineering analyses were performed for the adopted design fire event. The analyses considered the facility’s unique features including its fire safety systems to determine applicable design fire curves for structural durability analyses. The paper also outlines the process of defining the project specific fire curves for a specific design fire scenario and summarizes the results of heat transfer and structural fire durability analyses. This approach was aimed to assist the owner and Authority Having Jurisdiction to achieve practical decisions to the tunnel facility fireproofing.INTRODUCTIONFort Lauderdale–Hollywood International Airport (FLL) in Broward County, Florida is a major hub facility serving more than 23 million passengers annually. As part of the Airport Expansion Program, the South Runway (9R-27L) Expansion project aimed to meet ever increasing service demands via an increase to runway lengths. This necessitated the placement of one of the reconstructed runways on bridge structures over the existing U.S. Route 1 (US 1), a major north–south U.S. Highway that serves the East Coast of the United States, and the Florida East Coast (FEC) Railway, thus effectively creating multiple tunnel cells beneath the subject runway. For this project, HNTB suggested a tunnel fire damage mitigation system that would protect the runway major structural elements from the design fire event that may happen within the tunnel cells. This paper addresses the issues related to the fire event originating within the tunnel encompassing the US1 highway only, and deals with requirements of NFPA 502 [5] exclusively. Therefore, while approaching the structural fire protection issues for the specific tunnel cells beneath the runway structure, the requirements of the American National Standard NFPA 502 (Standard for Road Tunnels, Bridges, and Other Limited Access Highways, 2008 edition) were followed. Per this standard, regardless of tunnel length, all primary structural concrete and steel elements shall be protected in order to:"

Jan 1, 2016

By C. M. Diaz, S. W. Marcuson

In the late 19th century, the discovery of rich nickel-copper sulfide ore bodies in Sudbury and the need for tonnage quantities of the metal to be used in nickel steel armor provided the foundation for establishing the Canadian nickel industry. For almost 50 years, International Nickel was the key player. In 1930, Falconbridge Nickel entered the field. These two companies remain the key Canadian nickel producers. This paper discusses the factors that have influenced the evolution of nickel smelting processes. The initial Sudbury ore smelting and nickel copper separation technologies were imported from abroad. It was only in 1937 that International Nickel established a process research laboratory in Copper Cliff The explosive post WW II industrial development created a strong demand for a broader variety of nickel products. For both International Nickel and Falconbridge, R&D became an essential business tool to succeed in the new market scenery. In the last few decades, new technologies were developed and commercialized to respond to the raising cost of energy, society pressing environmental concerns, the advent of nickel laterites as an important source of new metal, the incorporation of new nickel producers to the market, and, therefore, the need to increase productivity. Canada thus became an important exporter of technology. In this paper, the authors review this history with the objective of highlighting the forces that have triggered the most important changes in Canadian nickel smelting.

Jan 1, 2005

By T. W. Wlodek

"AbstractIn this paper a new type of durable 'spiral-rolled' drill set is introduced and its performance discussed. Efficient and economical mine drilling-depends to a great extent on durability of the drill-set employed. Premature failure of this element damages the drill bit and is costly when tungsten carbide bits are used.Time of drilling of 'spiral-rolled' drill sets introduced at present in Canada is considerably larger than for the presently used drill steel, but laboratory simulated service tests and practical field tests show that the 'drilling life' of the spiral-rolled drill set is several times that of ordinary drill steel.Some features of differential plastic deformation and differential surface rolling, so called 'spiral-rolling', are given.Relations between the drilling machine drill set and characteristics of the ore are discussed. The effect of shims on conical drill rod attachments, the mechanism of failure of drill steel, .and stresses during mine drilling, are analysed.IntroductionIN MINE DRILLING operations, the main interests are: the drilling machines as a source of working energy, the drill set as the tool transferring the working energy to the cutting edges of the bit, and, finally, the drilling characteristic of the .ore or waste rock.This paper includes a review of the possibilities of metallurgical and mechanical improvements in the drill set, with particular attention to drill steel and the attachments.For economical and efficient mine drilling operations, a durable drill rod, attachment, and drill bit are essential. Premature failure of any of these parts interferes with mining operations and is costly."

Jan 1, 1955

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991