Search Documents

By R. R. Sayers

A series of coal- mine catastrophes in the latter part of the first decade of this century focused public attention on the need for safety in mines and resulted in the establishment of the Federal Bureau of Mines , whose primary function was to promote safety and improve hygienic conditions of workers in the mineral and related industries . These activities are carried out by the Safety Division of the Bureau's Health and Safety Service . In general , the work performed by the Safety Division personnel may be classified as educational and investigative . Instruction is given in accident prevention for mine officials and miners ; first aid to the injured ; the use and care of oxygen breathing apparatus ; and advanced mine rescue and recovery operations . A specialized safety course is offered to the petroleum and gas industries . Division personnel also aids in or directs rescue and recovery work after mine fires and explosions ; assists at first - aid and mine rescue contests ; conducts safety exhibits and demonstrations ; and presents safety talks , often accompanied by sound safety motion pictures or latern slides , before employee and official groups , at meetings of Holmes safety chapters , at mining institutes , and at other safety or technical gatherings . Coal - mine fires and explosions are investigated , as well as quarry or metalmine explosions and fires , miscellaneous accidents , health and safety hazards , and safety conditions at mines and plants ; safety devices are investigated and developed . Field studies cover ventilation , methods of allaying suspended coal - dust particles , prevention of dust accumulations , the proper use of rock dust to prevent or limit explosions , explosives practices , and the care and use of underground equipment . The results of these studies and investigations are widely applied in the various training courses and are prepared as reports and recommendations , which are submitted to interested persons or are combined and distributed to the public as bulletins , technical papers , miners ' circulars , information circulars , and reports of investigations . These studies also afford a basis for the development of new or modification of old Safety Decisions of the Mine Safety Board of the Bureau of Mines . The following pages review the accomplishments of the division as regards safety during 1942,2/ with like information for a series of recent years and summaries to date . A striking feature of the division's work has been the safety education of more than 1-1/2 million persons who have taken first -aid and mine rescue training courses . That these efforts over a period of 3 decades have been successful is revealed by the decline in coal - mine fatality rates and a somewhat smaller decrease in metal - mining and quarrying fatality rates .

Apr 1, 1943

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

By E. N. Harshman

The Wind River Formation of Eocene age is the host rock for large high-grade uranium deposits in the Shirley Basin. The major deposits are in a northwest-trending belt of sandstones that were deposited in stream channels and that were lithologically favorable for uranium accumulation. Paleotopography influenced the character and position of the belt. The major deposits within the belt are at, or near, the margins of large tongues of altered sandstone formed in the most transmissive parts of thick sandstone beds. At least two tongues of altered sandstone are present in the belt, one of which is 5 miles long, 3 miles wide, and 70 feet thick; the other tongue is somewhat smaller. Ore bodies consist of a few hundred tons to several hundred thousand tons of material containing from 0.10 to about 2.00 per cent U3O8. The ore mineral is uraninite associated with pyrite, marcasite, hematite, and calcite. Deposition is believed to have taken place when neutral to slightly alkaline, oxidizing, uranium-bearing ground water, on entering the basin, encountered a reducing environment. The reductant may have been H2S of biogenic origin. Geology played an important role in discovery, exploration, and development of ore in the Shirley Basin.

Jan 1, 1968

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l'Énergie et des Ressources du Québec, dans Ie cadre de I'entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d 'exploration, de cartographie, et d'évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d'alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l'être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l'Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990

By W. E. Young, D. T. Delicate

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Nov 1, 1963

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1910

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1917

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By Gustavo Mammana, Aníbal Amirá

El escenario que enfrenta la minería chilena en materia de productividad plantea el desafío de definir estrategias que contribuyan a optimizar los procesos de dirección, gestión de proyectos y operaciones, agudizados por el envejecimiento de los yacimientos, la disminución de leyes, la fluctuación de los precios de los commodities, y el costo de la mano de obra e insumos. Este trabajo busca difundir las herramientas empleadas y las mejoras obtenidas a partir de la aplicación del Modelo de Excelencia Operacional –ExOpeHS, orientado a aumentar la eficiencia y la productividad en proyectos de ingeniería y construcción, mejorando los procesos de selección y reclutamiento, logística y control de proyectos; así como de la herramienta denominada TF30D, destinada a mejorar en corto plazo los resultados en las faenas mineras Chuquicamata, Centinela y Sierra Gorda (Chile).

Sep 20, 2019

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1910

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1917

By A. P. Liu

Semi-industrial test on fine products of Meishan dressing plant was carried out with type RP80/25 high pressure roller mill produced by Homburg Corporation of Germany, and the influences of such factors as energy consumption, water containing, throughput and circulating load on rolling effect were investigated. Closed circuit experiment result showed that Meishan iron ore could be suitable for powder grinding with high pressure roller mill, and energy consumption of the operation was declined by 25%~30%, which was favorable for energy-saving, increasing production efficiency and improving grinding effects. According to above experimental results, this paper put forward the technical proposal of application of high pressure roller mill in Meishan, and pointed out some technical problems which needed to be settled urgently in technology disposal.

Jan 1, 2014

By B. Berhe, R. D. Lawrence, J. Hinzer

"The fortunes of mining companies and their implied value are tied to cycles - both economic and commodity – within which they operate. Hence the determination of appropriate future metal prices is one of the most critical factors faced by mineral valuators especially for advanced projects. Price, and hence revenue, is usually the most sensitive input to the valuation model. Empirical studies of past forecasts show that the success rate for commodity price forecasting is very poor. This paper explores various approaches and comments on their strengths and weaknesses. We conclude that careful evaluation of long-term metal prices is a key element and is hardly a luxury that can be left to simple averages or rules of thumb. INTRODUCTION Discounted Cash Flow (""DCF"") analysis, is well suited for the valuation of advanced mineral development assets, for which there are identified mineral resources and some form of economic assessment (Pre-Feasibility or Feasibility Study). The DCF method is also the most commonly used method for determining value for such assets. It provides a means of relating the magnitude of expected future cash flows from profits (or losses) to the magnitude of the initial cash flow (investment) needed for capital expenditures to purchase or to develop an asset for commercial production. The method proves useful in making investment decisions as it allows for the quantification of the Net Present Value (“NPV”), as well as the Internal Rate of Return (IRR) and Payback Period on initial investment capital. Valuation by its very nature is a forward-looking exercise. The DCF method attempts to estimate the NPV of expected future cash flows, by selecting factors that will likely affect future cash flow based on informed analysis. One of the most critical and sensitive factors is the determination of appropriate future commodity prices. “The variables that have the greatest impact on a DCF evaluation are the reserves, the metal prices, and the discount rate.”1 The determination of future commodity prices for valuation purpose or during M&A negotiations is a hotly contested issue. There are a number of analysts, institutions and specialized commercial data suppliers that provide both short and long-term commodities price forecasts. Also, the use of an aggregated mean for all available forecasts, or consensus forecasted prices for valuation purposes is not uncommon. The methods used in making forecasts for each forecaster may vary and in many cases may not be publically disclosed. Nonetheless, the aggregated mean of all forecasted commodity prices of reputed institutions is usually taken to “represent the market’s view of likely future commodity prices.”"

Jan 1, 2016

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1910

By B. S. Covino

The Bureau of Mines, U.S. Department of the Interior, is conducting research to devise substitute corrosion-resistant materials by using ion implantation to form alloyed regions near the surfaces of metals. These alloys were prepared by implanting 25-kev Cr+ and/or Ni+ ions into iron. Their resistance to corrosive attack was evaluated by determining their anodic polarization behavior under potentiodynamic conditions in a solution containing sodium chloride, boric acid, and sodium borate. These electrochemical studies have shown that the general corrosion resistance of ion-implanted alloys was comparable to nominally equivalent bulk alloys. The pitting-corrosion resistance of the ion-implanted alloys was superior to that of iron, although not as good as that of most of the bulk alloys tested.

Jan 1, 1980

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page I Wilkes-Barre, Pa * May, 1871 I 3 II Bethlehem, Pa August, 1871 I 10 III Troy, N Y November, 1871 I 13 IV Philadelphia, Pa February, 1872 I 17 V New York, N Y * May, 1872 I 20 VI Pittsburg, Pa October, 1872 I 25 VII Boston, Mass February, 1873 I 28 VIII Philadelphia, Pa * May, 1873 II 3 IX Easton, Pa October, 1873 II 7 X New York, N Y February, 1874 II 11 XI St Louis, Mo * May, 1874 III 3 XII Hazleton, Pa October, 1874 III 8 XIII New Haven, Conn February, 1875 III 15 XIV Dover, N J * May, 1875 IV 3 XV Cleveland, 0 October, 1875 IV 9 XVI Washington, D C February, 1876 IV 8 XVII Philadelphia, Pat June, 1876, V XVIII Philadelphia, Pa October, 1876 V 9 XIX New York, N Y February, 1877 v 27 XX Wilkes-Barre, Pa * May, 1877 vi 3 XXI Amenia, N Y October, 1877 vi 10

Jan 1, 1917

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

By Kamila Kazmierczak

Neste estudo utiliza-se o processo de metalurgia do pó para a elaboração de compósitos a base de alumínio reforçados com nanopartículas de TiO2. O compósito é obtido através de moagem de alta energia assim como a obtenção da liga AA2014 utilizada como matriz. A consolidação dos pós obedeceu à seguinte sequência: mistura dos pós segundo proporções específicas, compactação uniaxial, extrusão a quente e tratamento térmico. O material produzido foi estudado microestruturalmente mediante microscopia ótica e caracterizado quanto à dureza.

Aug 7, 2018

By Major William R. King U. S. Engineer

My attention was drawn to this subject just twenty years ago this month, when I was detailed to rebuild one of the bridges in Richmond that had been burned during the evacuation. We took pos

Jan 1, 1886