Search Documents

By C. Lorimer Colburn, Spencer P. Howell

"Numerous accidents are still being reported that have resulted from the delayed explosions in drill holes. Some of these accidents have boon due to retarded burning of the fuse, causing the charge to explode after the miners had returned to the face, but the majority have been caused by the minors drilling or picking into unexploded explosives, either in unexploded bolas or in broken rock. Although the industry has been cautioned by the Bureau of Mines, manufacturers of explosives, and other agencies regarding the care that is necessary in the handling of explosives, yet reports of these accidents are still being received and many of the accidents are fatal, They occur in spite of the best efforts of the mine officials and men, but many of those that have been reported could have been avoided if the following precautions had been observed:Misfires should not be approached even for the purpose of inspection until three hours have elapsed if fuse was used, and ten minutes if electric detonators or electric igniters were used. These are minimum recommendations. It would be preferable to allow a longer time, for fuses have been known to hang fire for twelve hours."

Aug 1, 1920

By Heikki K. Jalkanen

Thermodynamic properties of copper-iron mattes and slag-matte distribution of copper and some minor matte constituents (Ni, Co, Mo, As, Sb and Bi) are discussed on? the basis of equilibrium measurements: a change from. oxidic to sulfidic solubility as the predominant form of dissolution of copper takes place as matte grade decreases. Distribution coefficients of minor matte constituents are complex functions of sulfur and/or oxygen potentials?. The distribution behaviour of different? metals can be qualitatively derived from their affinities to copper and stabilities. of their sulfides and oxides. The equilibrium results are compared with commercially observed values. from Outokumpu.Oy flash smelting furnace.

Jan 1, 1983

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By Jimmy Guarnizo

El yacimiento de La Zanja ubicada en el caserío La Zanja, Santa Cruz de Succhabamba, Cajamarca, inició sus actividades de exploración en 1991 y las de producción en el 2010. MLZ construyó el embalse o reservorio llamado Bramadero, que acumula las aguas de escorrentía de la quebrada del mismo nombre durante el periodo de lluvias, las cuales son empleadas para el consumo humano en la unidad minera, y en menor escala durante la época de estiaje para los procesos de operación. En este sentido, el presente texto señala la construcción de la presa Bramadero, la cual genera agua para beneficio de las poblaciones ubicadas aguas abajo de las instalaciones. Asi también cuenta con un programa de monitoreo ambiental para vigilar la calidad y la cantidad de aguas superficiales y subterráneas. Por tal motivo, cuenta con estaciones hidrométricas para evaluar en tiempo real la calidad del agua en los cuerpos receptores del área de influencia de la unidad minera.

Sep 1, 2015

By C. Joulian, A. G. Guézennec, A. Chmielarz, Y. Ménard, M. Hanke, P. d’Hugues

"The copper concentrate used in this study is produced by flotation of a black shale organic rich ore. This resource is a carbonate-rich, polymineral concentrate. In the last 5-6 years, ore characteristics changed and the concentrate grades degraded. This study evaluated bioleaching of the concentrate in stirred tank reactors as an alternative to the pyrometallurgical technology that is currently applied, and which may no longer be feasible in future given the concentrate chemistry.The first part of the study focused on testing non-traditional operating conditions during continuous bioleaching experiments: high solids concentration (> 20% solids), reduced agitation and aeration rates. For the same residence time, bioleaching performance at high solids loading (25%) was the same as that reached during previous bioleaching experiments at 15% solids. No mixing or microbial issues were encountered. The bacterial consortium used in the experiments demonstrated a high copper tolerance.The second part of the study was devoted to technology development for metal recovery from copper bearing solutions obtained during bioleaching experiments. Due to the high copper concentration of the leachate, solvent extraction prior to electrowinning was not necessary. After iron removal, high quality copper cathodes (morphology and composition) were obtained from the PLS by electrowinning."

Jan 1, 2014

By Anne-Laure Bonnet

Les connaissances acquises au cours des dernières décennies sur les gîtes de métaux de base et précieux intensément métamorphisés (p. ex. Vokes, 1991; Cornell et al., 1992; Zaleski et Peterson, 1995) ont permis d?élaborer des guides d?exploration pour de tels gisements dans les terrains de haut-grade métamorphique (Spry et Scott, 1986; Rubin et al., 1993; Hand et al., 1994; Spry, 2000; Spry et al., 2000). Un transfert de ces connaissances à la cartographie des vastes terrains gneissiques non différentiés de la province de Grenville permet d?affiner l?approche cartographique nécessaire pour reconnaître les systèmes hydrothermaux métamorphisés en terrains vierges et peu diagnostiques puis d?en discriminer les divers halos d?altération (Corriveau et al.,1996, 1997, 1998, 2003; Williamson et al., ce volume). Cette approche prend en compte les « empreintes métamorphiques » observées sur le terrain, telles que les variations des assemblages minéralogiques, du mode et de la composition des minéraux métamorphiques, pour reconnaître des roches présentant une composition inhabituelle caractéristiques de protolites altérés par hydrothermalisme. Ces empreintes citées cidessus sont facilement reconnaissables dans les terrains de haut-grade où la recristallisation induit un grossissement des grains qui permet de déterminer la nature et le mode des minéraux dès les levés de terrain. Cette approche raffine la compréhension des terrains de haut-grade métamorphique et illustre que leur complexité (i.e. polyphasage de la déformation et du métamorphisme) n?est pas forcément une limite à leur exploration. Elle a donc été utilisée systématiquement lors des levés de terrain réalisés dans le cadre d?un projet de l?Initiative géoscientifique ciblée de RNCan. La zone cartographiée se situe le long de la marge sudest du Groupe de Wakeham dans le secteur est de la Province de Grenville. Deux régions ont été plus particulièrement étudiées, celle du lac Musquaro (SNRC 12K10, 11 et 14) et la région côtière comprise entre Kégashka, La Romaine et Baie des Loups (SNRC 12K1, 2, 3 et 7) (fig. 1).

May 1, 2003

By M. M. Fine

"INTRODUCTION One of the principal activities of the Bureau of Mines during the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydro-fluoric acid, such as the use of the anhydrous acid as a catalyst in high-octane-gasoline production and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorspar. 2/ In 1943 the consumption of acid-grade fluorspar was advancing at a more rapid rate than production and was only slightly less than production during the latter half of the year.The outlook for the postwar market for fluorspar is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid also are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a new peacetime demand for fluorspar equal to 60 to 75 percent of the war production, 5/ 6/ and others believe that the fluorspar industry will be permanently expanded. 7/"

Dec 1, 1947

By Michel Papadakis

El presente texto señala el proceso de la molienda, utilización industrial, aparatos, clasificación, modos de utilización, estudio del comportamiento del mineral y la evolución de los problemas de trituración. El proceso de molienda consiste en trasladar el material del estado granuloso al estado pulvurulento. En ese sentido, se busca transformar los materiales con el fin de aumentar su superficie total, así como los cambios físico-químicos. Asi mismo se define el comportamiento de los materiales en los molinos de bolas.

May 1, 1961

By Shun-ichi Satoh

THE electric arc welding of cast iron has been studied by Braune, Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer, Candy, Neese, Miller, Carter, American Welding Society, Namack, Lebrun, Achenbach, Jansson, Kochendörffer and others.1 The writer of this paper has been able to obtain a series of cast irons, from gray to white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (SiC) and graphite (C). In this work, he has found the curious phenomenon of barium- carbonate.

Jan 1, 1929

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.' In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By S. Zhang, Z. Hua, D. Feng, X. Tong, X. Xie

The separation and beneficiation of low grade collophanite has long been a technical challenge in phosphorous production. It requires the joint efforts of process design, reagents optimisation and operational control. In this study, the statistical response surface method was applied for determining the optimum reagent dosing in the flocculate flotation of a low grade (18.59%) collophanite ore. The dosage of three reagents, including a pH regulator (Na2CO3), depressant (Na2SiO3) and flocculant (modified starch), were input parameters of the modelling design. Two quadratic mathematical models were derived for prediction of grade and recovery based on the statistical design. Statistical analysis of the experimental results validates the reliability of the models. Through further calculation, the optimum dosage of the three reagents were found to be 3,020g/t Na2CO3, 1,990g/t Na2SiO3 and 880g/t modified starch, with which a maximum recovery of 75.81% and P2O5 grade of 30.08% was obtained from flocculate flotation test. Keywords: Process optimisation, modelling, froth flotation, collophanite ore, response surface methodology

Jan 1, 2020

By A B. Bayooke, A C. Robertson

In terms of underground tunnelling in metres advance per capita, Australasia compares well with the best world performers. This is because of the large number of metalliferous mines, coalmines and civil tunnelling projects, with the Australian tunnel advance for civil and mining projects exceeding 625?km/a. In terms of hard rock quarry extraction, Australia produces approximately 200?Mt/a of aggregates, roadbase, fill material and specialist rock products from its quarries, which equates to approximately 8?t/capita. Australian mining and tunnelling contractors are also of world standard and are used to excavating in a variable range of ground conditions in a competitive environment. One author has been involved in tunnel and underground space planning and quarrying in Australia for the past 25 years and predicts that, over the next 20 years, there will be a major swing towards underground space for commercial uses. This paper identifies the potential uses of underground commercial excavation and the planning and geotechnical challenges for the future. Underground quarrying creates new opportunities to extend existing quarries within their urban footprint with minimum impact on the surrounding community. Investigations by the authors reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. However, cities such as Helsinki have been planned in detail to utilise the rock resources beneath them. Brisbane is used as a case study for a practical application of commercial underground space and underground quarrying in Australia.CITATION:Bayooke, A B and Robertson, A C, 2014. Geotechnical challenges for underground commercial space and quarrying in Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The Mt Todd Project is located 42 km northwest of Katherine in the Northern Territory. The identified mineral resource estimate for the Batman gold deposit is 66.7 million tonnes (Mt) grading 1.4 grams/tonne (g/t). Proved and Probable Ore Reserves total 42.3 Mt grading 1.5 g/t. Orebody definition and reserve estimation is based on extensive percussion and diamond drilling. Exhaustive bias analysis comparing grades produced from different drilling techniques has been undertaken. Similarly, detailed check assaying programs have been run to validate grade data produced by commercial laboratories used during the exploratory drilling phase. Significant biases were established from both studies and appropriate 'corrections' were made to drillhole databases prior to final resource and reserve estimation. 3D geostatistical modelling has been utilised for resource and reserve estimation, with specialist consultants contracted for this work. At all times, interpreted geological controls on mineralisation, provided by

Jan 1, 1994

By Eduardo Gimenes Jabes, Thiago Pires Nagasima, João Ricardo Filipini da Silveira, João Batista Ferreira Neto, Marcelo de Aquino Martorano

Foi implementado um modelo matemático para simular a solidificação de ligas do sistema Nd-Fe-B no processo de lingotamento de tiras. O modelo foi baseado na aplicação da equação de condução de calor unidimensional através da espessura da tira e da parede do rolo refrigerado da máquina de lingotamento. A resolução numérica dessas equações permitiu o cálculo do perfil de fração de sólido através da espessura da tira e dos perfis de temperatura através da tira e da parede do rolo. A temperatura de um ponto da superfície do rolo oscila em ciclos formados pelo contato com o metal líquido (vazamento) e pelo destacamento de um pedaço da tira. A temperatura média do rolo aumenta continuamente, diminuindo a taxa de resfriamento nas tiras. Mesmo no início do processo, os pedaços de tiras que se destacam ainda não estão completamente sólidos.

Oct 1, 2019

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman. EDGAR RICHARD, Vice-Chairman. D. M. LIDDELL, Secretary, 7 Wall St., New York, N. Y. C. A. BOHN, Treasurer. JOHN V. N. DORR, LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman. JAMES G. CARLETON, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass., W. E. C. EUSTIS. G. A. PACKARD. Columbia Holds four sessions during year. Annual meeting n September or October. W. H. LINNEY, Chairman. OSCAR LACHMUND, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON, S. SHEDD. Puget Sound Meets second Saturday of each month SIMON H. ASH, Chairman. I. F. LAUCKS, Vice-Chairman. CHARLES SIMENSTAD, Secretary-Treasurer, 425 Lyon Bldg., Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT

Jan 7, 1917

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953