Search Documents

By James S. Browning

Heavy liquids have been used to separate minerals of different specific gravities for many years.4 5 6 7 8 9/ The method permits substantially quantitative evaluation of a variety of minerals and requires much less time than the usual methods of chemical analysis. This Bureau of Mines investigation was conducted to determine the applicability of heavy liquid mineral separation to the evaluation of certain spodumene and kyanite ores, prepared mixtures, and plant products. After careful standardization of the particular mineral and associated gangue, estimates of chemical analyses could be obtained from results of heavy liquid separations.

Jan 1, 1960

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By Robert T. DeGavre

INTRODUCTION The $645 million financing for Inco Ltd's Soroako nickel project in Indonesia not only represents a significant human achievement but also there are certain important lessons that can be derived from Inco's experience in financing the project. The paper will not present a technical assessment of the project since Inco Ltd. submitted a series of papers on this subject at the international Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979. BRIEF HISTORY OF THE SOROAKO PROJECT Table 1 summarizes the milestones achieved in the Soroako project and its financing. Exploration Phase A contract of Work was signed on July 27, 1968 by the Republic of Indonesia and F.T. International Nickel Indonesia (P.T. Inco) covering an extensive area of over 25,000 square miles on the two southeastern arms of the island of Sulawesi. The Contract provides that P.T. Inco has the sole responsibility for financing the project and determining the terms on which the financing should be obtained, that P.T. Inco has the right to receive and hold outside of Indonesia foreign exchange revenues and to freely dispose of such revenues, and that Indonesians have the right to purchase up to 20% of the equity of P.T. Inco over a period following start of production. P.T. Inco began field investigations in the Contract Area in August 1968. Preliminary reconnaissance sampling with portable drills broadly outlined areas of favorable laterite terrain which were then systematically sampled on surveyed grids. By early 1971 sufficient exploration work had been completed to indicate that the laterite deposits near Soroako could sustain a major nickel-producing plant (figure 1). Pilot plant studies in 1970 and 1971 at Inco's research station in Port Colborne, Ontario, using two bulk samples of Soroako ore material, also confirmed that the ore could be upgraded and treated for the recovery of its metal values. Feasibility Phase Encouraged by the results of its exploration program and pilot-plant work, Inco Ltd. commissioned Toyo Engineering Company of Japan in August 1971 to prepare a capital cost estimate for a relatively small nickel project called "Stage I". Stage I was to be a single-line pyrometallurqical process plant with an annual capacity of approximately 15,000 metric tons of nickel contained in 75% nickel sulphide matte (see Figure 2). Electric power was to be supplied by a thermal power station. It is important to recognize that Inco's strategy was to develop the Soroako ore deposits in several stages: first, construct a small project to gain experience and to reduce the initial capital outlay and then later expand in one or more steps to a much larger project to achieve maximum economies. The strategy reflected both Inco's financial position in 1971 as its sales and earning dropped sharply and the difficulties previously experienced by Inco in trying to launch in the late 1960's very large "greenfield" nickel projects in New Caledonia and Guatemala. Toyo's Project Development Study was completed. in January 1972. Based upon Toyo's cost estimate for physical facilities, Inco estimated the total capital cost of Stage I to be $115 million. For the next several months, Inco ran numerous in-house financial feasibility studies, using as inputs Toyo's cost estimate and the results of its exploration and pilot plant programs. In September 1972, Inco completed a project feasibility study which was based upon a capital cost estimate of $135 million. The feasibility study was immediately made available to potential partners and lenders. Partner Negotiations The Japanese nickel market had from the outset been central to Inco's planning for the Soroako project. That market had been growing dramatically at rates in excess of 20% per annum during the 1950's and 1960's. Japan had established, for rational security and other reasons, a domestic

Jan 1, 1985

By Werner A. Ruemmele, Steven R. Wardwell

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km (4.4 miles) of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Shank-Ohbayashi has two of the tunnelling contracts on this initial phase: A-171 and A-146. Contract A-171, the Wilshire/Alvarado Line, involves tunnel construction beneath 7th Street from the 7th/Flower Station to the Wilshire/Alvarado Station. The project consists of the excavation and lining of 3000 m (9900 ft) of twin-bore, 6.7 m (22 ft) excavated diameter, 5.5 m (18 ft) finished diameter subway tunnels. Contract A-146, the 5th/Hill to 7th/Flower Tunnels, comprises 1220 m (4000 L.F.) of twin-bore tunnel identical in cross section to the tunnels in Contract A-171. The majority of the excavation on Contract A-171 is beneath city streets in a weak siltstone/claystone bedrock with cover varying between 10 m and 25 m (32 ft and 82 ft) to the street surface. Approaching the 7th/Flower Station some fine-grained alluvium is encountered. The tunnels on both contracts are excavated with an open face digger equipped shield. On Contract A-146 the tunnel alignment is a 305 m radius curve of approximately 550 m (1800 L.F.) length underneath several multi-storied buildings of various construction. Excavation is still ongoing on Contract A-146. The contractor's choice for initial tunnel support on both contracts is a system of precast concrete segments similar to what the contractor had used on 7 miles of tunnel in Phoenix, Arizona, for the Arizona Department of Highways.

Jan 1, 1989

By S. M. Shelton, A. L. Engel

The carnotite deposits of western Colorado and adjacent sections of Utah and Arizona were formerly an important source of radium and uranium until displaced by the exploitation of foreign deposits in the Congo and northern Canada . Recently interest has been renewed in domestic carnotite ores as a source of vanadium . Carnotite is a canary - yellow, crystalline , pulverulent mineral occurring in sandstones in the Colorado - Utah district as an incrustation on the faces of joints and fractures and deposited around and between individual sand grains , often strongly adhering to the surface of the grains . Chemically, it is a variable combination of potassium, uranium , and vanadium oxides with water of crystallization . It is soft and friable , and occurs in fine - grained or earthy form . In spite of a specific gravity of 4.1 , gravity concentration has not proved practical as a means of beneficiation because of the earthy texture of the mineral . Vanadiferous sandstones occur with minerals ranging from roscoelite (vanadium mica) , containing little uranium , to high- uranium and low -vanadium carnotite . There is considerable local variation in the texture of the ores . The treatment of carnotite ores has been described previously , with attention directed to the elimination of waste in mining and the extraction of radium . The suggested methods included those suitable for the recovery of vanadium , since both radium and vanadium occur in the same minerals . Moore and Kithil suggested crushing from 40- to 80 - mesh with rolls , accompanied by a rubbing action to loosen the carnotite adhering to the sand grains . Fine grinding was to be avoided because it diluted the final product too much . The crushed and rubbed material was to be washed and

May 1, 1942

By Andrey de Moraes Barcelos Casanova

Sendo o alumínio um metal amplamente empregado na produção de partes integrantes de aeronaves, aonde este deve atender a requisitos básicos necessários, como uma boa resistência mecânica, fadiga e corrosão, aliado a baixa densidade, o estudo deste metal se torna pertinente. Visto tais necessidades deste setor, a avaliação destas se torna importante diante da possibilidade de utilização de processos de deformação plástica severa (DPS) para o refinamento de microestrutura, a qual irá acarretará assim, melhoras em propriedades mecânicas. Este trabalho teve por objetivo avaliar o comportamento mecânico, através da dureza HV, medida por um ultramicrodurômetro instrumentado, desejando encontrar uma maior homogeneidade microestrutural bem como o seu refino.

Oct 30, 2017

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By Chen Qizhou, Wang Yun, Zhu Rong

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Dario Libano

"The Line 5 Extension, in Sao Paulo, Brazil, is currently the most important investment in public transportation by Sao Paulo’s state government. It will connect the south part of the city to the city center, crossing through four other major Metro lines and stations; all currently in operation. The total extension of the line is 11 km (6.8 mi), and includes a new parking yard for the trains and 11 new stations. The Brooklin Station, one of the new stations due to be open and operating in 2016, has a unique geometry of five secant shafts.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One slurry wall, along the Santo Amaro Avenue, was to contain the contamination plumes, and another was for temporary support to enable the excavation of the shafts. The final retaining wall design was changed to a concrete structural diaphragm wall that reduced the construction time of the shafts by half, allowing the contractor to meet the construction schedule. This solution also avoided dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a hydromill was used in such a situation in Brazil. The hydromill, by overcutting the panels, increased the quality of the joints, and decreased the probability of having seepage into the shafts. The hydromill also created a seepage barrier and avoided movement of the contaminated plumes.The GeologyLocal geology is composed of a superficial Quaternary soil, basically soft organic clays and sands and gravels. From the depth of 8 m (26 ft) until 18 m (59 ft), geology is composed by tertiary medium compact sand with thin silt-clay layers. From 18 m (59 ft) down, there are alternations between compact silt-sands layers with very hard clays layers. Each is approximately 5 to 10 m (16.4 ft to 33 ft) thick.The Initial Basic DesignThe original basic design of the Brooklin Station was to be constructed from five 40 m (131 ft) diameter intersecting circular shafts, all in a line along the axis of the Metro tunnel, in 555 days. In the excavation sequence, the odd shafts were first excavated, waterproofed and had part of their inside cast-in-place structure built before the even shafts were excavated. During the excavation of the even shafts, part of the odd shaft’s support was demolished and connected with the even support. A 0.8 m (2.6 ft) thick plastic slurry wall, acting together with the wire mesh reinforced shotcrete support, ensured the excavation stability around the five shafts."

Jan 1, 2014

By Donald E. Ranta

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 assays and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1983

By C. Özgen Karacan

The methane emission rate into an underground mine environment from overburden strata during longwall mining is impacted by reservoir and geomechanical characteristics of the coal measure rocks in the overlying strata, as well as the presence of any coal seam. The reservoir characteristics and how they change during mining potentially affect the performance of gob gas ventholes, which consequently impacts the efficiency of methane control in the mining environment. This study presents reservoir and elastic properties of coal measure rocks in the Lower Monongahela Group in Greene County, southwestern Pennsylvania, of the Northern Appalachian Basin. Since the source of methane in this region from underground mining is located between the Sewickley coal and the Pittsburgh coal, a specific emphasis was given to this interval. Core analyses were performed in the laboratory to determine rock porosity and permeability. Geophysical logging data (gamma, density, sonic) obtained from two exploration boreholes were used for evaluating formation boundaries, shale contents, log porosities, and geomechanical properties of formations. Permeability was also calculated using density-log data and empirical equations and compared with laboratory measurements and slug tests performed in isolated intervals of boreholes. The results presented in this study can be used as data sources for reservoir studies related to the production and control of methane.

Jan 1, 2009

By Martin McKinnon, Guy Reed, Russell Frith

"It is arguable that the development of reinforcing roof bolting systems has largely stagnated in recent times, primarily due to the prevailing industry view that few, if any, further improvements can be made to what currently exists. However, this paper contends that reinforcing roof bolting systems can be further refined by considering both the specific manner by which horizontally bedded roof strata loses its natural self-supporting ability and the specific means by which reinforcing roof bolts act to promote or retain this natural self-supporting ability. The Australian coal industry insists on minimising bolt-hole diameter to maximise load transfer and on targeting full-encapsulation by any means necessary. This has led to a significant, albeit unintended, consequence in terms of overall roof bolting effectiveness, namely increased resin pressures during bolt installation and the associated potential for opening bedding planes that may have, otherwise, remained closed during the bolt installation process. Given that the natural self-supporting ability of roof strata is strongly linked to whether bedding planes are open or closed, logically, minimising resin pressures should be a significant benefit. This paper focuses primarily on three key issues that relate directly to the function of the roof bolting system itself: (i) the importance of proper resin mixing in the context of maximising load transfer strength and stiffness, (ii) the importance of minimising resin pressures developed during bolt installation, and (iii) the importance of maximising the effectiveness of the available bolt pre-tension. All mine operators should be invested in improving the individual effectiveness of each installed roof bolt, even by relatively small incremental amounts, so this is an important topic for discussion within the mining community."

Jan 1, 2017

By T. W. Wlodek

"AbstractSatisfactory mine drilling operations depend on the good performance of the drilling machine, and of what may be called the drill set, i.e., the following four elements: bit, attachment, drill rod, and shank end. The field performances of these four elements in the drill set are analysed and their service lives are compared. The most .common causes of service failure are reviewed and possibilities of increasing service life are discussed.The laboratory methods now employed for the simulated service testing of tungsten carbide bits, conical push-on and threaded .types of attachments, drill rods, and shank ends are described, and some results are discussed. The objectives of the research programme now being carried out •on the above mentioned elements are outlined.A number of mines in British Columbia, northern Ontario, and northern Quebec have been visited, and, with the co-operation of the C.I.M. Branches in these areas, meetings with representatives of the mining and steel industries concerned have been held. In this paper, the mechanical-metallurgical problems most frequently encountered and discussed during these visits and meetings are described and .analysed.IntroductionSUCCESSFUL mine drill operations depend to a great extent on• the satisfactory field performance of the four elements which form the mining drill set, shown diagrammatically in Figure 1.These important elements are:1. -The bit, which may be one of the following types:(a) Detachable tungsten carbide bit( b) Inserted rod bit, so called chisel bit( c) Detachable steel bit( d) Solid rod bit"

Jan 1, 1952

By Robert M. Weidenhammer

For years before the war, Coal had the reputation of being a sick industry. Currently it is operating at peak production and succeeding pretty well in keeping out of the red. But, says Mr. Weidenhammer, it will have a relapse as soon as the war ends unless (1) working capital can be built up; (2) it gets the support of the people and Congress; and (3) a truly long-range national fuel policy is formulated.

Jan 1, 1943

By Immo H. Redeker, O. E. Pothier, E. W. Gieseke

Phosphate rock is the primary source of phosphorus, an element necessary to all forms of life--plant, animal, and human. While phosphorus finds many uses in everyday life, it is an irreplaceable ingredient in all complete plant foods. With the present need for intensive farming, the fertility of the soil can be maintained only by external additions supplied by mines or other sources. A major consideration in any mining operation is to establish the economic and ecological impact of the development on the local population as well as the national interest. The Commodity Data Summaries, as published by the U.S. Bureau of Mines (USBM), is a ready reference concerning the importance of phosphate to the national and local interest. The summary of domestic and world pro¬duction is given in Table 1. During 19722 the demand for marketable phosphate rock exceeded the supply in the United States and the rest of the world. Domestic and world reserves are more than adequate to meet furture demands. Phosphate rock prices firmed and export prices increased, reflecting the change from oversupply to a shortage of phosphatic fertilizers. Demand is expected to exceed supply through 1973. New fertilizer plant capacity planned for 1973-74 will increase the production of phosphate rock by more than 5 million tons in the United States. Morocco and Spanish Sahara are scheduled to increase their production to 18 and 3 million tpy, respectively, within 2 to 3 years. The domestic phosphate rock production for 1972 was 40.8 million tons and 1973 was 42.1 million tons.' Industry, with government-supported programs, will emphasize restoration of mined land and solution of the colloidal slime disposal problem in Florida. The foregoing information comes by courtesy of The Division of Nonmetallic Minerals of the U.S. Bureau of Mines, January 1973. The summary gives a great deal of information but does not give a complete picture. There are many supporting industries which contrib¬ute to the area in which the mines are located. The figures shown in Table 1 deal with concentrates. To produce such concentrates many more tons of waste overburden and ore must be moved. Because of the competitive nature of the phosphate rock industry, data on concentration ratios not only are difficult to obtain but also are not for publication by companies. The concentration ratios vary from one mine to the next in Florida as well as in Tennessee and the western United States. To produce 42.4 million tons of phos¬phate rock in the United States required moving about 350 to 400 million tons of material. Domestic Industry. In 1972 some 26 firms and the Tennessee Valley Authority produced phosphate rock, with several firms produc¬ing from more than one mine. The distribution of marketable phos¬phate rock production was: Florida and North Carolina 82%; Idaho, Montana, Utah, and Wyoming 13%; and Missouri and Tennessee 5%. The value of this production was $223 million. The principal consuming classifications were: agriculture 75%, soaps and detergents 5%, plating and polishing 3%, animal feed supplements 4%, and miscellaneous applications 13%. Over 5,000 firms processed end-prod¬ucts for agricultural purposes. Uses of Phosphate Rock. The tendency in the United States has been to produce more phosphoric acid by the wet process, while the production of electric furnace phosphorus, triple superphosphate, and ordinary superphosphate has been on the decline. Exports of phosphate rock have been on the increase for several years and in 1971 reached 33% of total production. However, export sales of phos¬phate rock are expected to decline in the years ahead, both in total tons of sales and in percentage of production as domestic sales increase (see Table 2). The description and chemistry involved in the production of phos¬phate fertilizers is too complicated to be presented here. The Waggaman13 book is a very thorough reference on the subject involv¬ing production, utilization, and chemistry. The various operations generally have chemical plants near the dry plants or ship to associated chemical plants for further processing. Wet rock, dry rock, and ground dry rock of various grades are sold. In addition various grades of calcined phosphate rock, including defluorinated phosphate rock for animal food supplements, are pro¬duced. Various grades of phosphoric acid, superphosphate, triple suerphosphate, as well as diammonium phosphate, are produced. These products are available from the various producing compa¬nies listed in the text. For prices and specifications the producing companies should be contacted.

Jan 1, 1985

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By Riqing Ye

Laser Engineered Net-shaping (LENS TM) is an emerging manufacturing technique that ensures significant reduction of process time between initial design and final components. The fabrication of fully dense parts with appropriate properties using LENS TM process requires an in-depth understanding of the entire thermal behavior of process. In this paper, the thermal behavior during LENSTM processing of 316 stainless steel was studied both numerically and experimentally. Temperature distribution and gradient in the fabricated 316 stainless steel part were obtained by Finite Element Method (FEM) simulation. The numerical results are in good agreement with the experimental observations. The numerical method may be used to optirnize process parameters and predict the thermal response of LENSTM fabricated components. Key words: Laser Engineered Net-shaping, Thermal Behavior, Finite Element Analysis

Jan 1, 2003

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By Elwin L. Fisk

The Cordero mine is located in the Nevada portion of the Opalite Mining district that straddles the Oregon-Nevada state boundary. The mercury deposits of the district occur along the margins of the broad east-west graben valley of McDermitt Creek. The only other major producers, the Opalite and Bretz mines, on the northern margin of the graben have thus far exploited only shallow deposits within 100 feet of the surface. Through December 1965, Cordero has produced 94,680 flasks of mercury, the most of which came from the large underground cinnabar deposit. Nearly all of the mercury ore deposits in this district have been found in Miocene rhyolitic intrusives, flows, tuffs, and lake beds. These rhyolites have been argillically altered at depth and extensively silicified at or near the surface. These silicified areas or "opalite" masses were the original cinnabar-bearing outcrops.

Jan 1, 1968

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference index with abstracts of all pertinent literature. A particular strawman system design analysis is included for the Helvetia Coal Co. Lucerne #8 mine in the Upper Freeport seam.

Jan 7, 1979