Search Documents

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By Alfonso Brazzini Díaz Ufano

El presente texto señala la estrategia de la disminución del impuesto de ventas, así como el aumento a las tasas de renta dentro del desarrollo minero. Para ello, es necesario incentivar la ampliación de la capacidad instalada actual de la mediana minería a través de una ley, donde el Estado no deje de percibir súbitamente el impuesto a las ventas y pueda recuperar una parte de él por un impuesto a las utilidades cuando las empresas presentan recién sus declaraciones juradas, de forma que solicite a las empresas mineras a acogerse al sistema del pago a cuenta del impuesto a la renta en base a balances mensuales.

Mar 1, 1979

By J. M. Mutmansky

Procedures for the determination of the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques has been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the multitudinous mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the solution of problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To establish a major simplification in the development of procedures for the determination of the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1984

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with low ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the size range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for vari¬ous reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully.

Jan 1, 1953

By D. L. Hollis

An arc plasma reactor, constructed and used for studying extractive metallurgical processing, was adapted by the U.S. Bureau of Mines to separate gases of different masses by using the high rate of plasma rotation. With argon and helium as input gases, peripheral reactor outlet ports had a measured average increase of about 10 pet in argon concentration relative to helium with the plasma on compared with plasma off for the same gas inlet concentrations in both cases. Approximately the same average increase in argon concentration occurred from the peripheral outlet port compared with a central outlet probe with the plasma on. There was no difference with the plasma off.

Jan 1, 2010

By Peter McGoldrick

This Talk ?Australian deposits in world context ?Geological setting: the importance of the basin fill ?Key deposit features using HYC (McArthur River) and Century as examples ?The difference between Aussies & Canuuks(that is between Australian & Canadian sedexdeposits!) ?Timing of mineralization ?Sources for metals and ore fluids ?What makes a super giant sedexdeposit?

May 1, 2006

By R. K. K. Mbaya

The concept of adsorption or separation of platinum anions from base metal cations in chloride media using native or chemically modified activated carbons has been discussed in various journals within the context of batchwise systems. In our research work, a fixed-bed column, loaded with native and amine-immobilized activated carbon pellets (Norit RO 0.8), was used to study selective adsorption of platinum ions from chloride media at different flow rates, bed depth and initial metal concentrations. The kinetics, mass transfer characteristics, breakthrough data and separation factors (ß(Pt/Fe) and ß(Pt/Cr)) were quantitatively analysed and modeled. The bed-depth service time (BDST) model was used to model the breakthrough curves successfully in fixed-bed columns and also the dispersive diffusion in the radial and axial directions of the bed were evaluated. The inner diameter of the column was 3 cm and the bed depth was between 1.0 cm and 2.5 cm. Concentrated 4 M HCl acid solution was used to elute the fixed-bed column. It was demonstrated that amine-treated activated carbons provides superior separation factors between platinum and base metals (Fe, Cr). Results showed also, that 95% saturation was reached within 10~26 hours depending on the nature of ACs at a flow rate of 11 mL/min and initial concentration of 5 ppm.

Jan 1, 2014

By Daniel Asunción García Ramos

El presente texto señala la influencia del quebracho como agente tensoactivo que evita el problema causado por el azufre a través de concentrados, cuyas especies mineralógicas predominantes son: esfarelita, pirita, incrementándose la extracción de metales. En este sentido, este método hidrometalúrgico permite que los concentrados que tienen plomo y arsénico en su composición, sean neutralizados para neutralizarlos como sulfatos sólidos, mientras que los sulfuros de zinc y de cobre pasan a la solución acuosa en estado iónico para ser recuperados posteriormente por electrodeposición.

Dec 1, 2015

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By Sidney Katell

This report is an economic evaluation of the production of hydrogen in a continuous system by the steam oxidation of partially reduced iron oxide in a fluidized bed at 7 atmospheres using producer gas to reduce the iron oxide. The oxidation-reduction step is based on experimental data obtained by the Bureau of Mines at the Pittsburgh Coal Research Center. The estimated capital requirement for a plant producing 30 million std. c.f.d.3 of 99.8 percent purity hydrogen at a discharge pressure of 450 p.s.i.g. is $13,100,000, using January 1961 equipment cost data. Based on a 330-day operating year, the operating cost before profit and taxes with coal price as a variable is estimated to be:

Jan 1, 1962

By K. R. Garr, D. Kramer, A. G. Pard

EXPOSURE of steels to a fast-neutron flux results in helium generation by (n,a) reactions. The elements Fe, Ni, Cr, and N are major participants in the (n,a) reaction and helium concentrations of up to 5 x 10"5 atom fraction could accrue in fuel clads after a year of service in proposed fast reactors.' Such concentrations of helium can severely reduce the ductility of alloys at temperatures of reactor service. The phenomenon of helium embrittlement has been studied in austenitic alloys which were irradiated with particles as a rapid means of producing significant helium concentrations.2-5 The pres-ent work is a continuation of those studies and is concerned with helium effects in a ferritic stainless steel. I) EXPERIMENT Small sheet tensile samples with a gage length of 0.50 in. and a cross-section of 0.009 by 0.040 in. in the gage length were punched from cold-rolled type 405 stainless steel. The composition of the steel used in this work is given in Table I. Prior to helium injection, the samples were annealed 24 hr at 760°C which caused complete recrys-tallization with a resulting grain size of 40 u. This treatment rendered the alloy completely ferritic and carbide particles, 0.5 to 2 uin size, were present at a density of 1 x 1011 cm-3, Fig. 1. These carbide particles were probably a mixture of the M7C3 and M4C types.6 Helium was injected into the samples by irradiation with a particles from a cyclotron, which produced uniform concentrations through the center two-thirds of the sample thickness. Details of this procedure were previously described.' The average helium concentration, as measured on a gas-source mass spec- 11) RESULTS A) Tensile Tests. The results of the tensile tests are given in Table I1 where the values shown are averages of two samples. There was no significant effect of helium on either the yield strength or tensile strength at 550" or 650°C but an increase in both is apparent at 750°C. Samples with helium showed a 20 pct loss in total elongation at 650°C which increased to a 55 pct loss at 750°C. The uniform elongation is not affected by helium at 550" or 650°C but shows an increase at 750°C.

Jan 1, 1970

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By S McKnight, L Koroznikova, S Hall

Mineral sands represent an important new resource being developed in the Murray Basin, including parts of western Victoria. This paper will outline a simple methodology for mineral sands characterisation, developed as part of the AMIRA-managed project P777 æThe Development of Heavy Suspension Techniques for High Density Separations (Replacement of ClericiÆs Solution)Æ. This project is currently sponsored by three multinational mining companies (De Beers Consolidated Mines, Iluka Resources Limited and Rio Tinto Limited) and is developing an innovative laboratory mineral characterisation procedure that will allow the replacement of the currently employed highly-toxic chemicals.Mineral sand resources almost always contain more than one valuable (and relatively heavy) mineral. Titanium minerals are found with a large range of titanium contents, giving rise to density variation and often subjective mineralogical descriptions. Companies tend to rely on laboratory heavy liquid separation in the evaluation of samples arising from exploration, mining or metallurgical processes. Unfortunately, there are only a limited number of high density (æheavyÆ) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. However, beyond this value currently only organic liquids can be used. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used; however, this presents significant health and safety hazards. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0, hence æClericiÆs solutionÆ. For the characterisation of the heavy components of mineral sand deposits (eg anatase sg 3.9, rutile sg 4.2, ilmenite sg 4.4 û 4.7 and zircon sg 4.6 û 4.8) there is currently no heavy liquid alternative to ClericiÆs solution. ClericiÆs solution is highly toxic and testing is now conducted by very few laboratories worldwide with costs reflecting the chemical costs (though extensive efforts are made to recover and reuse the liquid, plus the requirement of its removal from the mineral samples), the infrastructure costs and health and safety regimes (eg blood testing of exposed staff, inventory management). A simple laboratory technique of density fractionation is being developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions, that can replace ClericiÆs solution in the evaluation of fine mineral sands samples (eg -250+150 microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 5.0 will be outlined and the comparison of results with ClericiÆs solution presented.

Jan 1, 2006

By Patrick D. McMaster

"INTRODUCTION According to the Roane Iron Co. of Rockwood, Tenn., the Chamberlain. Barnardville iron deposit produced approximately three million tons of iron ore previous to 1928. The deposit is divided into two synclinal bodies termed the north and south synclines. Production has come from the northern extremities of both bodies.The need for developing additional iron-ore reserves during the war prompted the Bureau of Mines to initiate an exploratory program on the Chamberlain-Barnardville deposit in February 1944, which continued until December 1944.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By O. D. Gonzalez

Existing measurements for the steady-state permeation of hydrogen in a iron above 100°C have been examined for contribution of determinate errors. The analysis leads to a recommended equation for the permeability of hydrogen in a iron: o= (2.9 ±0.5) x 10-3 exp - (8400 ± 400)/RT cu cm (ntp H2) cm-1 sec-1 atm-1/2 THE permeability of a iron to hydrogen has been the subject of numerous investigations over the past 40 years, and at present there are thirteen sets of published results for the rate of steady-state permeation of hydrogen in a iron above 100°C. The numerical values in each set of results are entirely self-consis-tent, but the spread among the sets is too large to be attributed solely to experimental error, i.e., to error other than in the specimen itself. Several reasons have been advanced to explain the disparities, but to date the relative importance of experimental inaccuracy to the spread remains uncertain. The purpose of this report is to examine in detail the sources of determinate errors inherent in the experiments and to assess as far as possible the contribution of the errors to the results. The ultimate goal is the selection of values for the permeability and heat of permeation most nearly representative of hydrogen in a iron. The analysis is limited to those experiments in which the permeation rate was observed at steady state—a condition in which traps for hydrogen within the metal are filled to a fixed level15 so that the trapping mechanism is not reflected in the rate of passage of the gas. Furthermore only data are examined in which surface processes are judged to have little or no influence on the flow. It is hoped with these restrictions to obtain values of the permeability and the heat of permeation which will be as closely related as possible to the mechanism of lattice diffusion. I) DEFINITION OF TERMS; UNITS In this report the data for permeation are given in terms of a coefficient oj permeability, ?, which is defined by the equation: jt=?A/?x{p1/2-po1/2) [1] where jt is the total flow of gas normal to the surface of a membrane of planar geometry, e.g., a disc, of area A and thickness ?x; pi and po are the pressures in the input and output sides, respectively. For flow radial to the walls of a membrane of cylindrical geometry, e.g., a tube, the corresponding equation is: where 1 is the length of the cylinder, and ri and ro are the inner and outer radii, respectively. The flux normal to the surface is given by Fick's law: j= -D(dc/dx) [3] At steady state the concentration gradient will be constant, and integration of Eq. [3] gives for the total flow through a disc of area A and thickness Ax: h =-DA(co - ci) [4] where c, and ci are the concentrations of solute at the output and input surfaces, respectively. When surface control is absent, co and ci are given by Sievert's law c = Kp1/2, and substitution therewith into Eq. [4] gives directly Eq. [I] where ? = DK. Integration of Fick's Eq. [3] in cylindrical coordinates will give Eq. [2] where again ? = DK and is thus shown to be independent of geometry (provided that surface control is negligible). The coefficient of permeability, or simply the permeability,* must be expressed in proper units. In *The term permeability will refer in this report always to the coefficient defined above; permeation will be used to specify the general phenomenon of gas passage through a membrane. this report ? will be expressed in the units of cu cm (ntp H2) cm-1 sec-1 atm-1/2. The variations of D and K with temperature are given by D = Do exp(-Ea/RT) and K = KO exp(-?Hs/RT) where E, is the activation energy for diffusion and AH, the heat of solution, each usually expressed in calories per mole of solute. The variation of permeability with temperature will thus be given (for conditions where surface control is negligible) by ? = ?o exp(-?Hp/RT) where ?0 = DoKo and ?Hp = Ea + ?Hs. The units of ?0 are the same as those of 6, and??Hp will be expressed in calories per mole H. 11) SUMMARY OF PERMEABILITY RESULTS Table I gives the values reported to date for the permeability of H2 in a iron in terms of ?o and ?Hp. Except where noted the parameters listed were taken directly from the numbers reported by the various investigators with only a change in units. The temperature limits within which the listed ?o and ?Hp hold are given in column 7; the limits marked in parentheses in this column indicate the entire temperature range covered in each investigation. The listed values of ?o and ?Hp are those giving a linear plot of ln? against T-1 at the higher temperatures in each set of measurements, and thus presumably represent the case for which surface control was negligible. Column 6 gives values of 9 at a representative tem-

Jan 1, 1970

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991