Search Documents

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By James Wm. White

Computer based dispatching in open pit truck haulage operations yields many benefits of current interest to mine management. The key tangible benefit is a substantial productivity increase with a given fleet of equipment or, alternately, a significant reduction in equipment required to meet production quotas. Other tangible benefits, depending on the operation, include minimizing rehandle, meeting several blending constraints simultaneously and ensuring a target plant feed rate. Intangible benefits include production forecasting, performance comparisons of trucks or shovels of different manufacture and extensive on-line report generation. Recent advances in mini and micro computer hardware and software and solid state electronics permit design and implementation of system features not feasible even a few years ago. Here we discuss many of these recent developments with emphasis on system aspects and dispatching algorithms.

Jan 1, 1983

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By C. A. Komar

The Bureau of Mines is investigating possible applications of acoustic energy at sonic and ultrasonic frequencies in petroleum production. A phase of this work involves measuring sound velocity through petroleum reservoir rocks. References and abstracts were prepared as a bibliography to make available to others some of the material obtained from a literature search covering the past applications and the present uses of sound. Laboratory and theoretical studies of the various parameters that influence the velocity of sound in porous media account for the wealth of information now available. Velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity logging systems, capable of measuring speed of sound waves in underground formations penetrated by wells, have been developed for interpretative studies. The close relation between acoustic velocity and porosity makes it possible to determine porosity from velocity logs. Most velocity log interpretation in terms of porosity is based on a formula developed by Wyllie and others known as the time-average relation.

Jan 1, 1963

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By D. R. Cook, W. M. Shepard, H. T. Morris

The East Tintic district in central Utah has produced ores of gold, silver, copper, lead, and zinc valued at more than $120,000,000. All of this ore has been produced from blind ore bodies in Paleozoic sedimentary rocks that are concealed beneath hydrothermally altered volcanic rocks and cut by intrusive bodies of Eocene age. The Paleozoic rocks, which range in age from Early Cambrian to Mississippian form the core and limbs of a large, northtrending asymmetric anticline that is cut by low-angle thrust faults, high-angle transcurrent faults, mineralized fissures and faults, and normal faults that are both older and younger than the mineralized fissures. The ore bodies generally may be grouped into two classes: ( 1) massive replacement bodies that are rich in silver, lead, zinc and manganese and (2) fissure veins that are valuable primarily for their content of gold, copper, and silver. The replacement ore bodies are localized chiefly in the Middle Limestone Member of the Ophir Formation of Middle Cambrian age where it has been thrust-faulted against older or younger rocks and cut by northeast-trending mineralized fissure zones. The fissure veins primarily are productive only in the Lower Cambrian Tintic Quartzite. Extensive lowgrade deposits of lead-zinc-silver ore recently have been discovered in Devonian carbonate rocks in the Lower plate of the East Tintic thrust fault but as yet are unevaluated. The principal guides to ore include: ( 1) intersections of northeast-trending fissures and crossbreaking faults that brecciate the carbonate rocks; (2) zones of late-stage pyritic, calcitic, and sericitic alteration in the lavas; ( 3) primary geochemical anomalies in the altered rocks; and ( 4) mineral zoning patterns of the known ore bodies. The present development of the Burgin mine would seem to assure the continued productivity of the district for at least a decade.

Jan 1, 1968

By Shiqiang (Rob) Hui, Jiaren (Jimmy) Jiang, Rees Llewellyn, Yongsong Xie

Wear has been estimated to cost the Canadian mining/mineral processing industry over $15 billion per year mainly for repair/replacement of worn parts in 2013. The associated production loss is difficult to quantify but add considerably to the problem. The Canadian oil sands sector which has to deal with extremely abrasive and erosive solids, has traditionally incurred extremely severe and often unique attack. Demonstrable progress in mitigating the wear problems has been achieved through materials development, more informed materials selections, and better component and operation condition designs. An integral contributor to these advances is a long-term collaborative research partnership between NRC and the mining/supply industry. In this paper, this continuing collaboration will be described. A main focus is to identify degradation mechanisms occurring in the most severe and important service applications and to correlate these findings with laboratory test data. Relevant abrasion and erosion (often combined with corrosion) properties have been established and correlated with composition and microstructures for all classes of resistant materials ranging from relatively soft elastomers to ultra-hard ceramics. A comprehensive wear properties database has been compiled. This capability has been instrumental in facilitating the development of improved materials, optimizing materials fitness/selection for service, wear failure analysis, and quality assurance.

Jan 1, 2015

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"Abstract — The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH ) regards ""wholediesel exhaust"" as ""a potential occupational carcinogen."" Threshold limit values (TLVs ) are recommended for the gaseous pollutants CO, CO2, NO, NO2, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sample these aerosols.The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, partial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine a quality.Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulage way and on haulage vehicles. Both full- and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO,CO2, NO, NC, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.Concentrations of CO, CO2, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m4, with a standard deviation of 0.19 mg/m3 DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 022 mg/m3."

Mar 1, 1992

By G. B. Harris, C. W. White

Cyanide has been used for the recovery of gold since the mid 1800s, but several jurisdictions have already banned its use, and environmental pressures are increasing to finding an alternative. Gold also forms chloride complexes similar to those of cyanide, but the use of chloride has never achieved widespread acceptance. This paper describes a chloride-based flowsheet, wherein the key unit process is the recovery and recycle of chloride ion. It is shown that the chloride-based flowsheet is competitive economically with the conventional cyanide-based flowsheets, and that it has a number of other advantages, particularly environmentally.

Jan 1, 2011

By Thomas J. Peters

In 1978, the U.S. Bureau of Mines and the U.S. Geological Survey completed a joint mineral survey of the Chemise Mountain and King Range study areas as mandated by the Federal Land Policy and Management Act of 1916, Public Law 94-579. The U.S. Bureau of Mines examined all identified mineral prospects and deposits; the results of these examinations are included in this report. The U.S. Geological Survey studied the regional geology, geochemistry, and geophysics; the results of these studies are available in USGS Map MF-1196. No mineral resources were identified in either the Chemise Mountain or King Range study areas; however, a high-grade silver and base-metal occurrence, and minor manganese resources were identified in between the two study areas, within the King Range Conservation Area. The only mining activity in either area was a placer gold prospect on Honeydew creek in the northeastern part of the King Range study area. Three samples from this prospect contained no gold. The Chemise Mountain and King Range study areas are in a mountainous region along the coast of northern California, 230 road miles north of San Francisco, and 70 miles south of Eureka by way of U.S. Highway 101, through Garberville and Redway. The Chemise Mountain study area consists of 3,941 acres; it includes the 2,598-ft Chemise Mountain, and the cliff-lined seacoast southeast of Shelter Cove. a resort and fishing village. The King Range study area consists of 39.764 acres northwest of Shelter Cove, and includes the northwest-trending King Range with elevations above 4,000 ft. The Chemise and King Range study areas are underlain by deep-water marine sandstones, shales, and minor pillow basalts of the Late Cretaceous and early Tertiary Franciscan Subduction Complex. Mineral production was 1,650 tons of manganese ore within a manganiferous bed overlying pillow basalt at the Queen Peak mine southeast of the King Range study area. However, no significant manganese resources were found in the Queen Peak area. The Point Delgada area, directly south of the King Range study area, has prospects with high grade copper, lead. silver, and zinc. Exposures are inadequate to estimate resources; however, the metals may be associated with Franciscan volcanism (volcanogenic). The Chemise and King Range study areas may contain similar economic silver-rich, base-metal deposits.

Jan 1, 1992

By Anderson Azevedo Agra

O Pó de Aciaria Elétrica (PAE) é um resíduo sólido gerado durante a fabricação de aços em usinas com Forno Elétrico a Arco (FEA). Esse resíduo contem quantidades apreciáveis de metais, tais como ferro e zinco, tornando sua reciclagem interessante não só do ponto de vista ambiental como econômico. Assim, esse trabalho teve como objetivo avaliar a autorredução de misturas de pó de aciaria elétrica e coque verde de petróleo (CVP). Para isso, misturas e pelotas de PAE:CVP, com variados teores de redutor, foram submetidas a ensaios de autorredução em termobalança e, na forma de pelotas autorredutoras, numa retorta aquecida em forno elétrico vertical. A redução das amostras foi analisada a partir da perda de massa das misturas. Além disso, a redução das pelotas autorredutoras foi observada através de análises de difração de raios X. Nestas análises foi possível verificar decomposição da Franklinita e a redução dos óxidos de Ferro e Zinco.

Aug 17, 2017

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By C. W. P. Finn

INFACON is of special significance to people in South Africa who are interested in ferro-alloys, because it was in South Africa that the idea of regular international congresses on ferro-alloys was conceived and developed. INFACON 74, the first-ever such congress, was held in Johannesburg from 22nd to 26th April, 1974, being organized by the South African Institute of Mining and Metallurgy, the National Institute for Metallurgy, and the Ferro Alloy Producers' Association of South Africa. Design Awards The Design Institute is inviting entries for the 1981 Shell Design Awards. Any product that falls into the three categories shown below, and that was designed in South Africa and is in production, is eligible for an award. Since their inception in 1970, the Shell Design Awards

Jan 1, 1981

By Shields H. Arup

The paper describes the innovative foundation reuse and strengthening works for two buildings in Central London. A 1950s building on piled foundations (65 Whitfield St) and a 1930s building (67-69 Whitfield St) on 3m deep pad foundations were both extended upwards by two new stories. The Client for the project is Derwent London, with Make as their architect, Main Contractor Multiplex and Engineer Arup. Little was known about the foundations of either building at the start of the scheme. Extensive investigations of the existing foundations and ground conditions were carried out in both buildings. At 65 Whitfield St, investigations identified piled foundations, but found that pile lengths were short and variable. As a result, strengthening works solutions were adopted whereby the increase in column load was shed into new mini piles constructed around the existing pile caps. At 67-69 Whitfield St, deep pits were used to investigate the foundations and reuse was justified based on understanding of the pad dimensions, concrete strength, and strength and stiffness of the underlying geology. For both buildings the residual risk was closed out through monitoring during construction. The combined reuse of the structural frame and foundations of both buildings facilitated a sustainable solution, breathing a new lease of life into outdated buildings.

May 1, 2022

By B. M. Thethwayo

Graphite blocks are currently used in the concentrate - slag zone in primary PGM smelters, and can possibly be extended to the matte zone. This project evaluates the interaction between synthetic matte and graphite blocks on a laboratory scale. Static crucible tests were performed where graphite crucibles (prepared from standard and high-grade graphite) were filled with synthetic matte (27.7 per cent S ? 46.1 per cent Fe ? 17.0 per cent Ni ? 9.2 per cent Cu) and heated to 1550°C for different time periods (1?5 days). Matte penetration was evaluated using a SEM, while graphite dissolution was evaluated by measuring the carbon content of the matte with a LECO carbon analyser. Matte penetrated into standard grade graphite up to approximately 2 mm, while matte infiltration into the high grade graphite was limited to the immediate hot face. The saturation solubility of graphite in the synthetic matte at 1550°C was 0.43 per cent. Copper, iron, nickel, and sulphur were detected in an accretion that formed in the water-cooled part of the furnace. This accretion consists of mainly Cu-S and Cu-Fe-S based phases.

Jan 1, 2012

By Jesús L. Valenzuela, José R. Parga, Salvador Aguayo, Héctor Moreno

The Merrill Crowe zinc-precipitation process has been applied worldwide on a large number of operations for the recovery of gold and silver resulting in a higher consumption of zinc dust from cyanide solutions. However, in some of plants this precipitate is of low quality, because lead, cadmium and especially copper are precipitated along with gold and silver. The low quality precipitate also requires more fluxes in smelting and shortens crucible life. In this study, a process is introduced to remove copper, silver, lead and cadmium from barren solutions following the Merrill-Crowe process. Copper and silver are removed by precipitation in a serpentine reactor, using sodium sulfide as the precipitator, and sulfuric acid for pH control. The recovery of lead and cadmium ions with natural hydroxyapatite using cow bone powder (CBP) as a new adsorbent material, is introduced. CBP is capable of removing lead and cadmium ions from aqueous cyanide solutions with 99% efficiency. It has the ability to compete with other existing commercial adsorbents for the removal of lead and cadmium. Results show that pH value has a significant effect on copper cyanide removal efficiency, and it was determined the optimal pH range to be 2 - 3. At this pH value, the copper cyanide removal efficiency achieved was up to 99 %; and for the cyanide associated with copper cyanide complexes, the recovery was 90%. Finally, the precipitate quality was improved 400% .This procedure was successfully run at three mines in México.

Jan 1, 2014

By Alen Shibu Joseph, Arvind Rajnarayan Singh, Mudila Dhanunjaya Rao, Kamalesh K. Singh

In this article, the cementation of major impurities from zinc sulphate leach solution by the addition of zinc dust was studied by considering different parameters including time, mesh size, and percentage of excess zinc dust. The output obtained from various experiments was utilized for the design of experiments. A multi-level categorical factorial design with a quadratic model was employed during this study. Results were predicted to minimize the concentration of impurity metals in the solution by altering the parameters. Furthermore, these predicted results were validated by performing another experiment. Successfully, it showed that the predicted and experimental data values were close to each other. The predicted optimized values were 40 min, 100% excess zinc dust, and 300 mesh size for copper; 42 min, 100% excess zinc dust, and 300 mesh size for cobalt; 37 min, 100% excess zinc dust, and 300 mesh size for cadmium; and 34 min, 100% excess zinc dust, and 300 mesh size zinc dust for nickel. At these optimized values, the experimental results showed 99.99%, 55.7%, 99.6%, and 76.6% cementation efficiencies for copper, cobalt, cadmium, and nickel respectively. The statistical design of experiments for the effective cementation of impurities corroborates the economic feasibility of optimizing parameters for the proposed process.

Jul 18, 2022

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986