Search Documents

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By G. McIsaac

"This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone’s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place.Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. “Whatif” scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan."

Jan 1, 2005

By K. K. Kelly

METALLURGICAL thermochemistry of titanium is a broad subject and (if data were available) could include a wide variety of topics. The present report is restricted to extractive metallurgy and to substances and reactions that bear upon the magnesium, sodium, and hydrogen-reduction processes employing titanium tetrachloride. The aim has been to present enough data so that the reader not only can check: the calculations for the reactions discussed but also can conduct related calculations if he so desires, without recourse to other compilations of data. The subject matter divides naturally into two parts-the selection of the data to be adopted and the application of these data to pertinent metallurgical reactions.

Jan 1, 1959

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary's report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

By D. W. Cooper

The AMAX of Canada Limited Kitsault mine is located approximately 150 kilometers, by air, north of Prince Rupert, British Columbia at the head end of A1 ice Arm, just east of the southern tip of the Alaskan Panhandle. It is presently only accessible by sea or air, although a road is being constructed by the company which will provide access to Terrace, a commercial centre with a population of about 15,000. The topography is typically coastal mountainous with peaks rising to 2,100 meters around the head end of the inlet. The concentrator is at an elevation of 515 meters with the mine at 630 meters. This open pit molybdenum mine was previously operated between 1968 and 1972 by British Columbia Molybdenum Limited, a subsidiary of Kennecott Copper Corporation. AMAX of Canada Limited has spent $194 million to refurbish and expand this operation.

Jan 1, 1982

By G. L. Oldright

This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth dealing with blast-furnace gases. It was noted in Report of Investigations 2957 that the gases evolved from the top of the lead blast furnace at Tooele were similar in composition to those from the top of an iron blast furnace. It was noted in Report of Investigations 3095 that at Kellogg, where a smaller percentage of coke on charge and shorter stock column were employed, the gases evolved were much less reducing. At times there was a considerable amount of oxygen in the top gases at the second plant. More SO2 was also evolved from sulphides in the charge. Then operations were conducted as at Kellogg, the gases were alternately reducing and oxidizing. This paper deals with the gases evolved in smelting a charge containing more zinc than at either of the other two plants with about the same amount of coke as was used at Kellogg,: To compare other factors influencing the composition of the gases, it may be noted that at Tooele the approximate height of the charge column was 15 feet, at Kellogg 9 feet and at Trail 13 feet. The furnaces have about the -same cross-sectional area- tog. The furnaces at Tooele are about 6 inches wider at the tuyeres, being 54 inches wide against 48 for the other two plants. At Tooele and Kellogg the furnaces are fed at the top from bottom-dump cars. At Trail the charges are dumped from Decauville cars (bottom cars which dump when tilted), which run on tracks placed on both sides of the blast furnaces. The hoods through which the waste gases are conducted are directly above the shafts of the furnaces. The flues for removing the effluent gases lead off from under the charge floor at Tooele and Kellogg. (Charging and distribution of the feed in the furnace covered later in a rate paper of series.)

Jan 1, 1934

Explosive manufacture, handling and transportation is hazardous and special precautions should be taken while manufacture, handling and transportation. Various regulations and rules defined in explosive act and factories act of India are discussed in this communication. General process control measures during the manufacturing of different types of explosives are also dealt in detail. Various processes hazardous in manufacture of various explosives like slurry explosives, PETN, detonators, styphnic acid, lead azide and lead styphnate and special precautions to be taken during the manufacture of the above explosives are also discussed.

Jan 1, 2007

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010

By J. H. Johnson

The report references reports and publications from 1975 to the present related to diesel underground mine air quality research undertaken by Michigan Technological University. Research results obtained on this contract are summarized in 5 different sections as follows: Section 1 - Development of a Systematic Approach to Monitoring, Data Analysis, and Interpretation for Diesel Mine Air Quality Control, Section 2 - Experimental Evaluation of LHD On-Board Air Quality Control Systems, Section 3 - Development of a Portable Self-Contained LHD Tailpipe Emissions Measurement Apparatus for NO , N0, CO, CO , and Particulate Matter, Section 4 Quantitative Analysis of Diesel and Coal particulate Matter by Laser Raman Spectro¬scopy and Section 5 - Development and Application to Detector Tubes of a Laboratory Method to Assess Accuracy of Occupational Diesel Pollutant Concentration Measurements.

Jan 1, 1985

By Howard M. Wells

Portfolio theory and the Capital Asset Pricing Model (Modigliani and Pogue, 1974) provides an investment decision rationale which takes account of the benefits of diversification in reducing effective risk, but this theory does not consider the financial capability of the firm to survive large losses if they should occur. The LL-curve theory (Wells, 1976) takes the latter consideration into account, but it does not provide for the effects of diversification. This paper pro- poses a general theory to account for both diversification and the financial capacity of the firm to underwrite the investment risks.

Jan 1, 1983

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By R. E. Morgan

Two sizes of Pennsylvania anthracite were gasified in the new-type Lurgi pressure generator at the Dorsten, Germany, works of the Steinkohlengas, A. G. These tests demonstrated that Chestnut-size anthracite and a Rice-Buckwheat mixture containing 27 and 19 percent ash, respectively, could be gasified satisfactorily at an elevated pressure in a fixed bed with oxygen and steam. These coals were especially prepared to approximate a rough-cleaned coal and a washed and screened product. The operating data obtained from the two tests and materials requirements are summarized. A wide range of reactant ratios could not be tested, nor could optimum operating conditions be determined, as the generator was being used throughout the testing program, employing normal operating practices, to produce gas for the gas grid; and the most economical coal, steam, and oxygen ratios may not have been used. Comparative costs are presented of the raw materials required for producing a high-B.t.u. gas, based on the operational data obtained from these tests and, to some extent, on data extrapolated from laboratory experimentation. A flowsheet of a proposed process for producing a high-B.t.u. gas by Lurgi gasification, followed by methanation, is also included.

Jan 1, 1958

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By Jas. G. Ross

Introduction Asbestos, a mineral known and used in ancient times, has become an article of commerce only during the life of the older asbestos miners in Quebec. The diversified uses of this adaptable substance are now numbered by the hundreds. Wherever insulation or resistance to heat may be required, asbestos, either by itself or mixed with some other material, may be employed to advantage. Regarded as a curiosity for centuries, it is now in such common use that it is familiar to all. The demand for long fibre for use in the manufacture of textiles and brake-lining, and for shorter fibre for making shingles, paper, and insulation materials, serves to support the industry of mining asbestos-bearing rock and milling the fibre from it in Canada, South Africa, Russia, Cyprus, and the United States. The commercial use of asbestos dates only from 1876, in which year large deposits were discovered in the Province of Quebec, Canada. Prior to that year a small amount of long fibre amphibole asbestos was produced in Italy. Occurrence In Canada In the Eastern Townships of Quebec, along the line of the Quebec Central railway, is an area of serpentine rock. It extends westerly into Vermont and easterly to Gaspe. A part of it, the section from Danville to East Broughton, contains areas in which occur deposits of commercial asbestos fibre of the chrysotile variety. Pits have been opened on some of these deposits at Danville, Coleraine, Black Lake, Thetford Mines, Robertson, and East Broughton. Thetford is distant 68 miles from Quebec city, East Broughton lies 25 miles to the northeast of Thetford, while Danville is 45 miles to the southwest of Thetford.

Jan 1, 1927

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

By D. E. Severson

The coal solution refining process under investigation is basically a modi¬fication of the German Pott-Broche Process, on which patents date back to 1927, (5, 6). This process was used in Germany during World War II for the partial dissolution of coal in hydrocarbon solvent and removal of the ash by filtration to produce a raw material for carbon electrodes for aluminum plants. At the end of World War II the German synthetic fuel program, of which this process was a small part, was abandoned as not economical. In recent times the whole field of coal liquifaction has been given a new impetus; present technology indi¬cates that the economic processing and refining of coal may be possible in the United States. A number of approaches to coal liquifaction have been investigated, and several of these are currently being funded by the U. S. Office of Coal Research. One approach is direct thermal treatment of the coal as in the FMC Project COED, in which coal is thermally cracked to produce gas, liquid products and char. Another approach is the Hydrocarbon Research Institute's H-coal process in which coal is catalytically hydrogenated. Two other federally funded projects involve the extraction of coal by solvents. The Consolidation Coal Company's Project Gasoline, now in the pilot plant stage in Cresap, West Virginia, is an attempt to produce gasoline plus a residual char by partial solution of the coal substance. The coal de-ashing process being developed by the Pittsburgh and Midway Coal Company is a modification of the Pott-Broche process. Coal derived solvent is used with hydrogen to dissolve the entire coal substance, subsequent filtration removes the ash and the solvent is recovered for recycling.

Jan 1, 1968

By William J. Priestley

Much time has been devoted, by metallurgists, to the study of steel after solidification and remarkable strides have been made in the heat treatment of steel, but less knowledge is available of the thermophysical activity of the constituents of steel prior to solidification in the mold. It is known that certain elements added to steel produce marked changes in physical properties, also that other elements added to steel produce similar changes, but we have only meager knowledge as 'to. how these elements combine in steel under different conditions of solidification. It is not sufficient to know, from chemical analysis, that a certain element is present in steel. We should know how this element is in combination with the other elements and whether the combination is such as will give the greatest physical properties. Certain elements go into solid solution with the iron, while others segregate to the grain boundaries and combine with the impurities collected there. Until it is known where an alloy produces the most beneficial effect and a means is determined for controlling its physical location by altering solidification conditions, or otherwise, we will not obtain the maximum value from our alloys. When molten steel freezes, it forms a heterogeneous mass of various crystalline constituents; and as the transformation of steel from a liquid state to the solid crystallized state is a critical step, involving as great a transfer of heat as any other operation in the making of finished steel, a variation in the rate of this heat transfer will have much to do with the arrangement of the various constituents in the solid state. The object of this paper is to show some of the effects on steel caused by variations in the rate of cooling in the ingot mold, particularly as to ingotism, segregation, dendrites, and intergranular material.

Jan 1, 1924