Search Documents

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today's highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada's mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

By T. Tamagawa, N. S. Fu, I. Iwasaki, M. Kobayashi

A 3-stage fluidizing bed process of chlorination, selective oxidation and sulfur chloride conversion was tested for processing of a chalcopyrite concentrate. It was found that the use of excess oxygen was essential to a stable operation in the oxidation reactor. The oxygen-excess gas will inevitably cause the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and the selective oxidation steps with separate flow paths of the fluidizing gases, thereby preventing the passage of oxygen-excess gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratory-scale fluidizing bed setup.

Jan 1, 2000

By T. Deng

Flotation of rare earths is complicated by the number of mineral classes that carry rare earth elements, including carbonates, phosphates, and silicates that often co-occur within the same deposit. Gangue constituents often belong to the same mineral classes as the rare earth minerals themselves. Chemical regimes developed for specific separations employ customized combinations of collectors, modifiers, and depressants that are not directly translatable to other operations. In this rougher flotation case study, a reagent suite including phosphate ester and sulfosuccinamate, originally developed for the recovery of bastnasite and monazite from silicate hosted ore, could not be applied to a synchysite ore hosted in carbonate gangue because the suite was aimed at silicate gangue rejection only. The separation of a fluorocarbonate mineral from carbonate gangue required a different chemical regime involving the use of hydroxamate and sodium silicate. Maximizing rare earth recovery was complicated by the presence of slimes. The effect of desliming and the increase in grind size was explored.

Jan 1, 2014

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010

By M Passmore, N Poznik

Olympic Dam is a world-class deposit and is unquestionably one of the most geologically, structurally and texturally complex orebodies in the world. As development advances into the Southern Mine Area (SMA) the geological understanding is rapidly evolving as underground drill rigs are prioritised to provide the additional data necessary to convert Indicated and Inferred Resources into Measured Resources. The SMA represents approximately 70 per cent of Olympic Dam’s total resource and is significantly more complex when compared to the Northern Mine Area with respect to the diverse nature and origin of lithotypes, rock mass characteristics and the extent of major structures controlling primary mineralisation trends.Recent mine development into the central SMA has been impacted by a major structural gouge zone. Sound geological interpretation allowed mine geologists to successfully integrate their local understanding of the distribution of lithotypes with critical geotechnical data, chiefly rock quality designation (RQD), to delineate and better predict this major structural gouge zone. As a direct result, development rates improved whilst also increasing awareness for the importance of sound geological interpretation utilising all available data. In order to maximise predictability across all systems in place through the mining geology value chain, the integration of geological and geotechnical data in a geotechnical RQD block model provides an additional tool to assist in preventative solutions for complex problems to achieve a proactive mining environment.This paper details the methods used to build the RQD block model, the geostatistical estimation parameters, 3D geotechnical domain wireframes, challenges regarding legacy approaches, and collection of geotechnical information and incorporating/linking geotechnical data with geological features, including the use of grade and lithotype domains. Although the geotechnical block model proved difficult and complex to construct, the resultant product has seen successful integration of geological and geotechnical data into mine planning providing higher resolution of critical parameters for local mining areas.CITATION:Clark, J M, Passmore, M and Poznik, N, 2017. Olympic Dam rock quality designation model – an integrated approach, in Proceedings Tenth International Mining Geology Conference 2017, pp 27–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this interesting subject. In the up of the electrical arrangements touched on in this paper, the author has had the able assistance of his friend Mr. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer is better than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant. Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of before it is possible to arrive at a proper decision.

Jan 1, 1912

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By Almon F. Robertson

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are being made primarily to provide preliminary information to the Department of Interior agencies and to others concerned with planning the proposed Federal power developments within the Missouri River Basin. This report has been designed to permit public distribution of the factual data obtained . Virtually all known metallic -mineral occurrences and some nonmetallic mineral deposits within Fergus County were investigated in 1948. The investigations cannot be considered complete , however , because some long inactive mines or prospects may have been missed . Most of the old mine and prospect openings now are caved ; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from available Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

By Beverly Cramp

In 1995, mining engineer Alain Gachet thought about using Earth-observation satellite imagery to search for precious minerals. The latest radar Earth-observation satellite, Canada’s RADARSAT-1, had just been successfully launched at the time, creating new opportunities for commercial applications. Gachet was working in Congo Brazzaville as an oil executive and general secretary of Elf Congo for the French national oil company Elf Aquitaine. He understood that the RADARSAT-1 launch promised new and cost-effective sources of data for mineral and oil exploration. “It was early 1996 before I ordered my firstRADARSAT-1 satellite images,” said Gachet. “I was first struck by the quantity of information delivered by the radar images. Linear structures and faults were clearly defined and subtle topographic features were tremendously enhanced,” he said. “It was ‘tree top geology,’ but this kind of information appeared to be key for finding new gold seams.”

Jan 1, 2003

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power inputs over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge, which was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2013

The Awareness and Preparedness for Emergencies at the Local Level (APELL) program is a process that helps people prevent, prepare for and respond appropriately to accidents and emergencies. APELL was developed by the United Nations Environment Program, in cooperation with industry groups, governments and local communities. Since its beginnings in1988, the program has been implemented in more than30 countries. APELL is a tool for bringing people together to allow effective communication about risks and emergency response. The program provides a common-sense approach to accident prevention and response.

Jan 1, 2003

By J. A. HUFF, V. V. BAKER

This circular is intended to present in brief form the statutory provisions of Pennsylvania regarding mining operations, in force at the end of the 1931 session of the legislature. lo reference is made to general laws which affect mining only incidentally in common with other subjects, such as the workmens compensation law. The statements have been condensed as far as practicable, and provisions not deemed of general interest, such as matters dealing only with administrative details, have been omitted. This circular obviously is not written with such particularity as to be of great value to the legal profession, but it is hoped that it will be beneficial to the mining industry in giving this information in a relatively compact form. At the end of each paragraph the statute from which it is derived is cited to facilitate reference to the text of the law. It is planned to publish additional circulars from time to time dealing with the mining laws of other States. Any criticisms of the form of publica- tion followed herein, or suggestions aimed at the improvement of future circulars, will be welcomed.

Nov 1, 1932

By Joan Stoupa

The expansion of the West Point wastewater treatment plant located in Seattle, Washington, will require a permanent tieback retaining wall to enlarge the plant site for the new treatment plant facili­ties. The retaining wall will extend approximately 3,000 feet along the property boundary between the treatment plant and the neighboring Discovery Park. Wall heights will range from 35 to as high as 65 feet. The purpose of the retaining wall is to provide a more uniform grade on the plant site and to resist lateral pressures exerted by the upslope, unstable hillside. During preliminary design of the retaining wall, various wall systems were evaluated based on assumed subsurface soil conditions. Results of preliminary studies indicated that expected subsurface conditions and wall heights made a permanent tieback retaining wall feasible. However, uncertain loads on the wall and the capacity of anchors in the native soils were significant. As a result, a detailed geotechnical program was conducted. The scope of the program included conventional drilling, sampling, analyses, and a field test program to determine site-specific anchor capacities. This paper describes the anchor test program and results.

Jan 1, 1990

Utilizing a very large database from a mined-out area on a South African gold mine, the relative efficacy of a method to mitigate the smoothing effect introduced by the algorithmic constraints imposed by kriging was investigated. Smoothing effects arising from limited data availability are differentiated from the smoothing arising from the application of estimation algorithms. Very little can be done to ameliorate smoothing of estimates because of too little data, barring additional drilling or sampling. However, the smoothing effects resulting from the kriging process are shown to be mitigated by use of an alternative algorithm. The primary criterion in the development of the new algorithm was to avoid re-introducing conditional bias. This paper examines firstly the smoothing effects introduced into estimates via the kriging covariance matrix, secondly the process for ameliorating the smoothing effect, and finally it uses a case study to demonstrate the effectiveness of the new algorithm on a very large database. The database was used to introduce a 60 m by 60 m drilling pattern which in turn was used to model the semi-variogram and produce 30 m by 30 m kriged block estimates. The follow-up database was then re-introduced (roughly 5 m by 5 m grid spacing) and averaged into 30 m by 30 m blocks to provide a direct comparison with the initial estimates. In this way the extent of smoothing and accuracy of the estimates before and after the corrections was tested.

Jan 1, 2014

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014