Search Documents

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Charles L. Harness, A. T. Coons

Sodium carbonate, Na2CO3, more commonly known as soda ash, is the most important of the alkalies. Sulfuric acid is the only heavy chemical, Soda ash enters the market either as the natural product or as a manufactured derivative of common salt. Notwithstanding their common occurrence in closed basins of the Western States, natural sodas are produced at present by only four firms, all in the same California area, and satisfy only 4 percent of domestic demand for soda ash; soda ash made from salt supplies 96 percent of the requirements. The impossibility in wartime of routing all westbound American shipping through the Panama Cami.l has curtailed Pacific Coast receipts of soda ash and-increased the importance of local resources of natural carbonates. One of the most promising of ·these is the recently discovered trona (sodium sesquicarbonate)· deposit 2o·mnes· west of Green River, Wyo. Reserves are likely to run into hundreds ·of million·s of tons, and the deposit probably could be worked by the room-and~pillar· system of mining, like common salt or coal. • • Raw materials ·ne·cessary for manufacturing synthetic soda ash occur closely associated in m·afiy parts· bf the United 8tates. Almost unlimited resources of salt in brines and in rock-salt depbsits are located near limestone quarries in many areas. The· limesto'ne furnishes the carbon dioxide for the manufacture of soda ash arid the lime f o'r the recovery of ammonia. used in one step of the process. Expansion of the industry to meet wartime needs depends chiefly on availability of trained labor, materials, and equipment necessary for the erection of additional units.

Jun 1, 1942

By Edward R. Rose

This paper summarizes and emphasizes the potential importance of Canadian rare-earth occurrences, and recommends that efforts to locate and evaluate rare-earth deposits should be increased. Increasing world markets, depending on intensive applied research into the numerous unique and remarkable chemical and physical properties of the rare-earth elements (REE), are developing; their properties and uses are becoming better known; methods of separation are much improved. The REE group comprises a Cerium (Light) subgroup of 7 metals and an Yttrium (Heavy) subgroup of 9 metals. REE are trace elements in many rocks and minerals, and major constituents of more than 50 rare-earth minerals, many of which are difficult to detect and identify. They occur preferentially in acidic and alkaline igneous and metamorphic rocks, including carbonatites, as well as in placer deposits, certain uranium deposits, phosphate rocks and others. The main ores now are bastnaesite (in Precambrian carbonatite), monazite and xenotime (in Recent beach sands) as well as uraninite and brannerite (in Huronian quartz-pebble conglomerate) and loperite (perovskite) and apatite (in alkaline complexes). World resources are summarized. Twenty mines in 1973 produced an estimated world total of about 31,000 tons of contained rare-earth oxides (REO), 19,341 tons of which came from one mine at Mountain Pass, California. A selected fifteen, of 315 or more Canadian occurrences, are briefly described and compared, and their relative merits indicated. Their abundance and variety suggest the possibility of finding high-grade deposits in many geological terranes in Canada.

Jan 1, 1979

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By Jameel Menashi

A process has been developed for recovering the refractory metal values contained in mixed secondary source materials such as contaminated grinding wastes, oxides and sludges. The wastes are calcined with sodium carbonate in air to convert the refractory metals to water soluble Na2CrO4, Na3V04, Na2Mo04 and Na2W04. The base metals, Fe, Ni, Co and Cu, are converted to water insoluble oxides. An aqueous leach of the calcine effectively separates the refractory metals from the insoluble base metals. Co, Ni and Cu can be recovered from the oxidic residue by conventional processing methods. The leach solution is purified and then treated to recover the refractory metals as Cr203, NH4VO3, (NH4)6Mo7024?4H2O and H2WO4. The purity of the products is sufficient for their use in many metallurgical applications. The Na+ values in the leach solution are recovered as Na2CO3(or NaHC03) and are recycled to the calcination step. It is shown that the process can accommodate a wide range of feed compositions and generates a minimum of aqueous effluents.

Jan 1, 1984

By Sydney H. Ball

I. INTRODUCTION. DURING the past 50 years the attention of mining-men has been turned to Africa, and within the past decade prospecting-expeditions sent into Central Africa have resulted in the opening-up of several mines. Having recently spent two years in the Belgian Congo for the Société Internationale Forestiere et Miniere du Congo, it is our purpose to outline briefly the mining-conditions in that part of Central Africa. Before it became, in 1908, a Belgian colony, this region was known as the Congo Free State. II. LOCATION AND AREA. The Belgian Congo lies in southwestern Central Africa, west of the continental divide, is illustrated in Fig. 1. It has a coastline of but 20 miles on the Atlantic, but widens rapidly eastward to points 5° north and 14° south of the equator. Its area is 908,000 sq. miles, which is almost one-quarter that of the United States and Alaska, or more than one and one-half times that of Alaska. Stated in other terms, its area is nearly one-third that of the United States, exclusive of Alaska and the insular possessions, or more than that of all the United States east of the Mississippi river. III. TOPOGRAPHY AND DRAINAGE. From north to south, Africa is made up of three topographic elements: 1, the Atlas mountains, a highly-accentuated region

Apr 1, 1910

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Joan Weinberg

Seasonally adjusted new factory orders for primary metals declined in January, February, and March, especially in the steel industry. The decline was part of an apparent slowdown for the entire manufacturing sector. Orders for all durable goods, including not only primary metals, but also clay, glass, and stone products, fabricated metal products, machinery, and transportation equipment, fell in January and February. In March, orders rose a slight 0.8%. According to the U.S. Department of Commerce, the downturns in durable goods orders in January and February were the first back-to-back declines in 3 years. They were largely attributed to a drop in orders for transportation equipment, mainly auto-mobiles and aircraft, while the small gain in March was due to a surge in aircraft orders. Higher interest rates may be partly responsible for the slowdown in durable goods orders over the past 3 months. The higher rates have also hit the construction industry--another major end-user of minerals. Construction of new homes and apartments fell by a seasonally adjusted annual rate of 5.4% in March, following a 12% decline in February.

Jan 1, 1989

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By J M. F Clout

Geological, textural and mineralogical classification of iron ores is routinely conducted by mine and exploration geologists on reverse circulation percussion, blasthole cone and bulk samples for grade control, defining ore and waste, determining lump:fines ratio and predicting downstream processing characteristics. Classification is based on physical hardness, colour, streak and other visual characteristics. However, logging is generally restricted to the five to 20 per cent of chips above about 2 mm. This means that most of the sample is too fine to be reliably logged for anything but colour or streak and the textural types must be inferred from other information. A recently developed software package called æRecognitionÆ allows automated identification and classification of iron ore textural types and gangue on a particle basis in polished section down to 0.01 mm using processed digital images. It is not designed to be used as a routine logging tool, but is applicable where higher definition is required at the resource evaluation stage on selected percussion, drill core or bulk samples. æRecognitionÆ processes data obtained after optical image analysis of fine iron ore samples. It contains several parts, like æRecognitionÆ, æCompositionÆ, æLiberation by Total IronÆ, æLiberation by PhasesÆ and æStatisticsÆ, which allow vast and diverse information to be obtained about the iron ore samples being studied. Identification and classification of the textural type of each particle is performed according to the CSIRO-Hamersley Iron Ore Group Classification Scheme. The recognition procedure encompasses a good knowledge of different ore types and a logical knowledge tree, managing fuzzy boundary problems and the potential for a few different ore types in the same particle to be considered. This new technology introduces strict criteria to make the process of identifying particles more objective. Automated recognition standardises the identification procedure and significantly saves time. It enables users without a strong background in mineralogy to perform accurate texture identification. The æRecognitionÆ package has a modern user-friendly interface and Word compatible output. The combination of all the features mentioned makes the package a convenient tool for detailed studies of fine iron ores.

Jan 1, 2005

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By Chen Dong, Yang Wenwang, Liu Zhineng, Tan Ming

"To meet the requirement of production expanding of a certain potash ore dressing plant in Xinjiang province of China, industrial test of XCF/KYF-50 flotation machine was performed to process potash ore. The tank of XCF/KYF-50 flotation cell is in U shape, 50m3 of volume. This flotation cell is able to suck slurry by itself, and can be arranged on the same base level without high difference. In this paper, two sets of XCF/KYF-50 flotation cells were adopted to replace 8 sets of 8m3 flotation cell in original flow sheet of flotation. Aeration rate, slurry suction capacity, power consumption and slurry suspension are investigated. The measuring results show the slurry suction capacity of the flotation cell is larger than 12.80m3/min and solid particles disperse evenly in the tank without deposition. Industrial test result indicates that the final grade of concentrate is 26.69% at the recovery of 90.95%, which is up to expected performance. XCF/KYF-50 flotation cell has advantages of high flotation efficiency, significant energy saving and reasonable configuration of automatic control system, this kind of flotation cell can meet the requirement of production expanding of this potash ore dressing plant well."

Jan 1, 2014

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922

By R. B. Ellestad

Introduction Lithium has been known since 1817, when it was discovered by the Swedish chemist, Arfvedson, while working in the laboratory of Berzelius on the chemical analysis of the mineral petalite, LiAl(Si205)2. Development of the chemistry of lithium proceeded slowly, following the early work of Davy, Gmelin, Bunsen, and Matthiessen. Approximately seventy years elapsed before lithium products assumed any commercial importance, and for a considerable period it was a' very minor industry. Their chief early use seems to have been in medicine, and in the production of lithiated water. Other more important uses were gradually discovered, and the industry has had a slow but steady growth. Chemistry Lithium is classified as an alkali metal, along with sodium, potassium, rubidium, and cæsium. Like these, it is a silvery-white metal, which can be cut with a knife; it is harder than sodium, but softer than lead" It is remarkable in having a density of only 0.53 gram per cubic centimeter, which makes it the lightest metal. On ignition in air, it burns intensely to form chiefly lithium monoxide, Li2O. Like the other alkali metals, lithium reacts vigorously with water to form hydrogen and lithium hydroxide. The later is a strong base, and reacts with acids to form salts. The salts of lithium are in general analogous to those of the -other alkalies, but many of them have unique properties. For example, lithium chloride and bromide are extremely hygroscopic, and have a very high water solubility. Lithium fluoride, phosphate, and carbonate, on the other hand, are all relatively insoluble, unlike the corresponding sodium and potassium compounds. In this instance, lithium exhibits its frequent tendency to resemble the alkaline-earth group of elements (calcium, strontium, and barium). Many of the special and valuable properties of lithium are related to the extremely small size of the lithium ion.

Jan 1, 1948

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada's general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a 'favourable balance of trade' - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

By Roberto Maldonado Astorga

El presente texto señala la implementación del modelo de gestión para las operaciones de Volcán Campaña Minera, basado en el Modelo de Gestión de Malcom Baldrige. El modelo tiene el objetivo de establecer un proceso sistemático y estandarizado que asegure la mejora contínua y en línea con la visión de la empresa que apunta al logro de la excelencia operativa. La estrategia se divide en tres módulos: Módulo de Organización, Módulo de Gestión y Módulo de Comunicación. Asimismo se busca, implementar círculos de optimización permanente, monitorear de forma sistemática la ejecución de iniciativas de mejora y seguir el impacto en los indicadores.

Nov 1, 2014

By Robert Hopler

Testing Stations Abroad At the Seventh International Congress of Applied Chemistry, Drs. Mente and Will communicated a paper on the above subject. All large coal-getting countries employ testing stations of some kind, in order to safeguard, to the highest possible extent, the lives of the men employed in this industry. Most countries employ galleries of considerable diameter, and fairly short length; but within recent times, long galleries, with drives and other accessories approaching as closely as possible the actual conditions of mining have been installed. The following are the details of the testing stations employed in the countries mentioned.

Jan 1, 2010

By L. Harris

The Yanacocha project is the first foreign investment in Peruvian mining since Cuajone during 1976. Three years after the project began, it has become the largest producer of gold from heap-leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha SA (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits. And it has attracted the interest of foreign investors in Peru’s mineral resources. Construction began on Aug. 1, 1992. The first gold bar was poured on Aug. 7, 1993 from ore from the Carachugo Mine. During 1993, Minera Yanacocha produced 2.5 t (81,000 oz) of gold and 9.4 t (304,000 oz) during1994 (40% above budget). Production was expected to exceed 15.5 t (500,000oz) during 1995 with the start-up the Maqui Maqui Mine.

Jan 1, 1996

By G. W. Phelps

The field of industrial minerals is concerned with both sieve size and distribution of sub-sieve particles. A great deal of work has been reported on the techniques designed to provide information of this work. The term sub-sieve is here considered to include particular material that will pass a 325-mesh testing sieve. Plant men require rapid, precise and simple testing techniques that are, if possible, inexpensive with respect to equipment and manpower. A number of particle-size procedures have been developed, based on the Stokes equation for streamline movement of a particle of diam D, moving at velocity V through a liquid of viscosity n. 1 Particles are considered to be rigid, smooth spheres, completely dispersed at low concentration and moving at low velocity through the suspending medium with no slippage between particle and liquid. In particle size determinations the particle moves either from natural gravitational forces or those provided by centrifugal means. The diagram of Fig. 1 shows a spherical particle of density S and diam D moving downward at velocity L/T (or V) through a liquid of density So and viscosity n. The forces of gravity G (natural) or Gc (centrifugal) cause the particle to move through the liquid, thereby creating a viscous drag F or Fc. Within the streamline flow

Jan 1, 1967