Search Documents

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By S. Escoffier, A. Giraud, K. Su, F. Homand, N. Hoteit

Abstract For the feasibility study of an underground waste disposal the characterization of the coupled behaviour of the host rock is required: Because of the very low permeability of these formations few experimental data are generally available. In this framework the uses of the sensitivity studies could orient the experimental efforts by highlighting the key parameters of the formation. This paper gives a first approach of the sensitivity studies performed with probabilistic methods in the geomechanical field. A one dimensional model which characterizes the thermohydromechanical response of an argillaceous rock to the excavation of a waste canister site and its setting up, is considered. Zusammenfassun Die Machbarkeitsstudie eines tiefliegenden Endlagers für radioaktive Abfälle beinhaltet die Untersuchung des gekoppelten Verhaltens des im Lagerbereich anstehenden Gesteins. Aufgrund der sehr geringen Wasserdurchlässigkeit dieser Formationen liegen häufig nur wenige experimentelle Angaben vor. Die Verwendung von Sensibilitätsstudien kann in diesem Zusammenhang als Hilfsmittel zur Entscheidungsfindung dienen. Dabei sollen die maßgeblichen Eigenschaften der Formation festgestellt werden, anhand derer der Umfang der experimentellen Erkundung festgelegt werden kann. Dieser Artikel stellt einen ersten Ansatz zur Durchführung von Sensibilitätsstudien mittels einer mechanisch-probablistischen Kopplung im Bereich der Geomechanik sowie die Vorteile gegenüber Parameterstudien vor. Zur Abbildung des thermohydromechanischen Stoffverhaltens von tonigem Fels während der Schachterstellung und der Einlagerung der Abfälle wird ein eindimensionales Model verwendet. Résumé L'étude de faisabilité d'un centre de stockage de déchets radioactifs en profondeur passe par la caractérisation du comportement couplé de la roche hôte. Du fait de la très faible perméabilité de ces formations, souvent peu de données expérimentales sont disponibles. Dans ce cadre l'utilisation d'études de sensibilité permettrait d'orienter les efforts expérimentaux en faisant ressortir les caractéristiques primordiales de la formation. Cet article présente une première approche de la réalisation d'études de sensibilités à l'aide de couplages mécano-fiabilistes dans le domaine de la géomécanique. Un model unidimensionnel caractérisant la réponse thermohydromécanique d'une roche argileuse au creusement d'un puit de stockage et à la mise en place de conteneurs de déchets est considéré.

Jan 1, 2003

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By Attie J. Goosen, William L. Spiteri

Although the physical characteristics of ANFO made from porous prilled ammonium nitrate (PPAN) have been altered by the addition of crystal modifiers, the optimisation of prilling processes and the admixture of waterproofing agents, the sensitivity of this explosive has not been modified on a commercial scale in the 40 years since its accidental discovery.

Jan 1, 1995

New Bio-Adsorber with Activated Carbon and Nano Tube Carbon for Separation of Nickel and Cadmium

Sep 13, 2010

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.

By Leon Lorenzen, Charlene Gokhale

"In excess of 24 x 106 tons (Eskom, 1997) of coal-derived fly ash is produced annually in South Africa for the production of electric power. A large quantity of this ash is disposed of as a solid waste in landfills, thus posing a serious environmental problem. Due to the shortage of landfill sites, new ways of utilising fly ash are needed. Recently several authors have shown that various combustion fly ashes can be converted into zeolites to obtain industrial products with applicability in environmental management. Geopolymerisation has emerged during the last few years as a possible solution to some waste stabilisation and solidification problems. henolic compounds have been shown to be toxic to soil microorganisms at the parts-per-million level. Indeed several of the organic compounds classified by the U.S. Environmental Protection Agency as priority pollutants, are phenols. Immobilisation of phenols by adsorption on zeolites and encapsulation in a geopolymer appears to be a promising solution to this problem.This paper reports a technique for the production of a low-silica sodium zeolitic material from fly ash (zeolite NaP1), and its application for the stabilisation of phenols by adsorption and subsequent encapsulation in a geopolymer matrix. A commercial zeolite, clinoptilolite was also utilised as an adsorbent. Due to their uniform pore sizes and large surface areas, zeolitic materials are suitable for ion exchange and adsorption of certain organic substances. Adsorption data show that the commercial zeolite, clinoptilolite was an effective adsorbent for organics. Adsorption data showed that between 51.2 ppm and 74.3 ppm of chlorophenol or between 15.4 ppm and 32.5 ppm of phenol could be adsorbed. Physical encapsulation of the coated zeolite loaded with organic within a geopolymeric matrix increased the compressive strength of the matrix from 28.80 kN to 40.79 kN. Leaching data for the various geopolymer matrices with encapsulated and loaded zeolites show no organics being leached from the system at a detection level of 2ppm. According to the SABS these would have been acceptable organic concentrations within a waste water stream."

Jan 1, 2003

By T. Dlokweni

Several Rockmass classification systems have been developed and used in Civil Engineering design and for underground mining operations. Some of these rockmass classification systems have been modified and used in the South African coal mining industry to quantify descriptive geological information for use in coal mine design and roof support selection. The Coal Mine Roof Rating (CMRR) system developed in the USA has been investigated in detail as part of the study. Advantages and disadvantages of the system have been identified by means of underground and surface borehole testing. Investigations into the rating systems in South Africa found that most of the rating systems used in the South African coal mining industry are for planning purposes, and are conducted on borehole cores. This study also highlighted that the rating systems being used are based on geology, and that the human factor plays a major role in the rating systems. To overcome these problems, all the classification systems used in South African coal mines have been benchmarked against impact splitting technique and documented. The best elements of these systems are combined into a new standard system that will be easily used by all mine geologists and rock mechanics engineers. Plusieurs systèmes de classification de la masse rocheuse ont été développés et utilisés dans le Génie Civil et pour les opérations d'exploitation minière souterraine. Certains de ces systèmes de classification de la masse rocheuse ont été modifiés et utilisés dans l'industrie minière sud-africaine pour quantifier l'information géologique descriptive utilisée dans la conception de mines de charbon et la sélection de soutènement du toit. Le système d'Evaluation de Toit de Mine de Charbon (CMRR) développé aux USA a été examiné en détail, comme part de l'étude présente. Tests en surface de trous de mine ont permis d'identifier les avantages et inconvénients du système. Une étude des systèmes d'évaluation en Afrique du Sud a révélé que la plupart des systèmes d'évaluation utilisés dans l'industrie minière sud-africaine sont utilisés pour la planification, et sont menés sur les carottes de trous de mine. L'étude présente a aussi souligné que les systèmes d'évaluation utilisés sont basés sur la géologie, et que le facteur humain joue un rôle majeur dans les systèmes d'évaluation. Pour surmonter ces problèmes, tous les systèmes de classification utilisés en Afrique du Sud ont été référencés en termes de technique de fissuration sur choc, et documentés. Les meilleurs éléments de ces systèmes sont combinés dans un nouveau système standard qui sera utilisé aisément par tous les géologues de mine et les ingénieurs miniers. Verschiedene Gesteinsmassenklassifikationssysteme wurden entwickelt und kamen im Design für Hoch- und Tiefbau und Untertageabbau zum Einsatz. Einige dieser Gesteinsmassen-klassifikationssysteme wurden modifiziert und sind in der südafrikanischen Kohlebergbauindustrie in Verwendung, um beschreibende geologische Informationen für die Anwendung im Design von Kohlebergwerken und der Firstabstützungsauswahl quantitativ zu beschreiben. Das in den USA entwickelte Kohlengrubenfirstbewertungssystem (CMRR) wurde als Teil der Studie im Detail untersucht. Vorteile und Nachteile des Systems sind mittels der Untergrund- und Oberflächenbohrlochprüfung gekennzeichnet worden. Prüfungen der Bewertungssysteme in Südafrika ergaben, daß die meisten Bewertungssysteme die in der südafrikanischen Kohlebergbauindustrie benutzt werden, Planungszwecken dienen und werden anhand von Bohrlochkernen durchgeführt. Diese Studie hob auch hervor, daß die verwendeten Bewertungssysteme auf Geologie basieren und daß der menschliche Faktor eine Hauptrolle in den Bewertungssystemen spielt. Um diese Probleme zu überwinden, wurden alle in südafrikanischen Kohlengruben benutzte Klassifizierungssysteme vergleichsweise in Hinblick auf Spaltschlagtechnik überprüft und dokumentiert. Die besten Elemente dieser Systeme werden in ein neues Standardsystem kombiniert, das leicht von allen Grubengeologen und von Gebirgsmechanikingenieuren benutzt werden kann.

Jan 1, 2003

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

By P. Christmann

"In June or July 2005, the European Commission will present its Thematic Strategy on the Sustainable Use of Natural Resources proposal to the Council and European Parliament, one of the seven Thematic Strategies to be developed and implemented under the 6th European Environment Action Programme in support of the European Union’s Sustainable Development Strategy defined by the European Union’s Head of State at the Göteborg European Council, in June 2001. The time scale for this Thematic Strategy is 25 years (2005-2030). This paper discusses some of the key issues related to the EU minerals and metals industry that needs to be addressed by the Strategy. These are: - the need for access to mineral reserves in the EU and abroad; - the need to strenghten the capacity of developing countries to sustainably promote and regulate the use of their mineral potential; - the need for an EU mineral resources intelligence capacity. There are additional important needs, which are not discussed in this paper, such as: - the need to foster further innovation in mining, ore beneficiation and metallurgical technologies; - the need to integrate and simplify the exisitng complex regulatory framework applicable to the EU mining industry and to effectively implement existing legislation."

Jan 1, 2005

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By Claude Bazin, Patricia Obiang

"The slurry density (pulp percentage of solids) and the size of the grinding media are often used for the optimization of an operating ball mill. In many cases a change of ball size is made at the slurry density used with the original ball size. But is the optimum slurry density changing with grinding media size? Laboratory grinding tests were conducted to answer that question and results indicate that more than likely there is no need to adjust mill slurry density when adjusting the size of a grinding media in a ball mill. Full scale behaviour could be different because slurry density affects the slurry transportation through the mill and the classifier operation.INTRODUCTIONOre preparation begins with a fragmentation step that liberates valuable minerals or exposes mineral surface to the environment. The size reduction step of a mineral processing operation is energy demanding and the optimisation of this process should always be an objective for the plant metallurgists. Various approaches could be considered for improving the operation of a grinding circuit. For a close grinding circuit an adequate tuning of the classifiers operation may lead to substantial savings (McIvor, 1988). Once a grinding mill is in operation, few variables remain to be considered for process optimization. The ball charge is usually maintained to achieve a target power drawn by the grinding mill motor. The rotation speed is seldom considered (McIvor, 1983; Bazin and Lavoie, 2000) as a change of mill speed usually implies a costly pinion change. If the liner and lifter configuration is critical for SAG and AG mills (Latchireddi et al., 2005), few discussions are available for ball mills (Fuerstenau and Abouzeid, 1985; McIvor, 1983). The mill feed size distribution can also be adjusted but this implies changing the upstream processes, which transposes the optimization process to another level. Modification to grinding media shape is a possible avenue (Cooper et al., 1994), but it remains that slurry density and grinding media size are probably the most frequently considered variables for the optimization of a ball mill."

Jan 1, 2007

By Susan Jacob

The heat of fusion of silver was measured using high temperature differential scanning calorimetry (HTDSC). Heating rate, sample mass, calibration standard and cover gas flow rate were varied to determine their impact on instrument accuracy and reproducibility. Good reproducibility was achieved in most of the runs. Accuracy was not satisfactory in most of the runs, though three runs gave results within 1.7%, 3.3% and 3.5% of the literature value, within the acceptable limits. A larger mass and higher heating rate tend to generate more accurate results.

Jan 1, 2006

By Stanley C. Suboleski

1977 was the modern day low point for productivity in the coal industry. At that time, no one could have predicted that the industry was about to enter a productivity rise that would continue unabated through the 1980s. Thirteen years later, the cause of this phenomenon is still not well understood. While many government studies focused on the fall in productivity from 1969 to 1977, none have been undertaken to explain the rise. Some of the likely causes of the gain in productivity during this period will be discussed here. An attempt will also be made to quantify the value of some of the technical innovations that have taken place. The remainder of the gain is assumed to come from non-technical sources. The nature of these sources, although largely non-quantifiable, is also discussed. Since the number of mines that have adopted the technical innovations noted here is largely unknown, the actual contribu¬tion of technological changes to the overall productivity gain can only be estimated.

Jan 1, 1990

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009