Search Documents

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By Khaled Morsy

The studied mine extracts the Sewickley seam using room-and-pillar method. The overburden at study site ranges from 400 to 800 ft. Eight years earlier, the Pittsburgh seam was mined 80 ft underneath the Sewickley seam. Parts of the mains at the study site experienced problems of rib spalling associated with floor heave. Numerical modeling was used to explain the mechanism of ground control problems encountered at the mains of the upper seam. The modeling results show that the ground control problems encountered were caused by multiple seam interactions with the previously mined longwall panel of the lower seam. Based on the modeling results, a criterion to predict the probability of multiple seam interactions was proposed.

Jan 1, 2006

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By C. Haberfield, J. Szymakowski

Recent studies by the authors into the behaviour of jointed rock masses using direct shear testing have confirmed that joint spacing has a significant effect on rock mass strength. The rock mass failure envelopes assessed from these tests have been compared to failure envelopes obtained using the Hoek-Brown GSI criterion. Good agreement between measured and estimated GSI strength envelopes where obtained when joint spacing was considered in the assessment of GSI. Les études récentes conduites par les auteurs sur le comportement des joints rocheux employant l'essai direct de cisaillement ont confirmé que l'espacement a un effet significatif sur la force de la masse rocheuse. Les enveloppes de ruptures obtenues pour ces essais ont été comparées à l'enveloppe de rupture obtenue en utilisant le critère GSI Hoek-Brown. Une bonne corrélation a été constatée entre les enveloppes obtenues expérimentalement et les enveloppes calculées par la méthode GSI quand l'espacement des joints a été pris en considération dans l'évaluation de GSI. Kuerzliche Untersuchungen der Autoren betreffs Reaktionen von gebrochenen Felsmassen zu direkter Scherkraft, bestaetigen, dass die Abstaende von Rissen einen deutlichen Einfluss auf den Widerstand der Felsmassen hat. Die Bruchbereiche der Felsmassen die von diesen Untersuchungen entwickelt wurden, wurden verglichen mit den Bruchbereichen, die man mit der Anwendund der Hoek-Brown GSI Formulierung erhaelt. Eine gute Uebereinstimmung zwischen gemessenen und errechneten GSI Festigkeitsbereichen wurde erzielt, wenn der Abstand der Risse in der Berechnung der GSI in Betracht gezogen wurde.

Jan 1, 2003

By Thierry Bernard, Phillipe Cappello, Jean Marc Laboz

"The main reasons of the emergence of electronic detonators are linked to:-Local urban development close to mining operation sites-Environment regulations"

Jan 1, 1995

By Forrest T. Moyer

Quarry accidents in 1963 caused 61 fatal and 3,468 nonfatal injuries which occurred at respective frequency rates of 0.31 and 17.91 per million man-hours of worktime. The fatality record in 1963 was better than in 1962 but was appreciably worse than in 1.961. For nonfatal injuries, the 1963 record was slightly worse than in 1962 but was better than in 1961. The injury--severity rate of 2,913 days lost or charged per million man-hours in 1963 was better than that of 3,046 in 1962, the first year for which such data became available. The average severity of all injuries in 1963 was 160 days lost or charged per injury, 15 less than in 1962. An average of 91,960 men were at work on active days in 1963 and these men had an aggregate worktime of 193.7 million man-hours during the year.

Jan 1, 1972

By R Sridhar, M Fe, W G. Bacon

The problems of magnetite build-up have plagued the non-ferrous pyrometallurgical industry for many years. To better understand these problems, a study was undertaken to determine the thermodynamic variables that affect the behaviour of magnetite under different smelting conditions. Equilibration studies were performed in the nickel smelting systems of matte-gas and matte-slag(silica saturation)-gas. The relationship of thermodynamic variables such as temperature, sulphur and oxygen partial pressure and matte grade on iron and magnetite activities were calculated and the significance on smelting parameters such as metal losses and partition coefficients were defined. The experimental data from this study were employed to develop practical methods which could be used to control the build up of magnetite, as well as to obtain additional metallurgical benefits. In general, a lower sulphur partial pressure and higher temperature operation was shown to enhance the metallurgical benefits of nickel smelting by decreasing the magnetite activity. Operating in this manner can also have added benefits such as higher metal recoveries, more efficient vessel utilisation and efficiency and lower smelter emissions at equivalent or higher primary furnace matte grades.

Jan 1, 2000

By J S. J van Deventer

Geopolymerisation is a new technology that processes and transforms aluminosilicate minerals into mechanically strong and chemically stable products. In this investigation, minerals such as fly ash and kaolinite were used as the solid raw materials for geopolymerisation. Inorganic salts were added to the geopolymeric pastes to simulate ionic contamination during processing for building and construction applications. The resultant products were examined and characterised physically. It was found that the early strength development of geopolymeric pastes could be changed according to the nature as well as the extent of the contamination. At a small dosage, the effect of the contamination on the early geopolymeric system depended heavily on the nature of the artificial surfaces that were created in the geopolymeric solution through the addition of the chemical additives. For example, the samples containing MgCl2 and Mg(NO3)2 had shown the same yield stress developments due to the similar surfaces that were formed. The cations of these salts were expected to hydrolyse and form magnesium hydroxide precipitates immediately after the addition to the early geopolymeric systems. The calcium cations of CaCl2 also precipitated upon addition, but the nature of the surfaces of these hydroxides was quite different to those of the magnesium hydroxides and gave rise to different yield stress development. The samples that contained the insoluble salts (in water) demonstrated different yield stress development when compared to each other because of the different nature of the additive surfaces that were exposed to the geopolymeric solution. These results suggested that heterogeneous nucleation could be responsible for the change of the rheological behaviour upon inorganic salt addition. When the extent of the ionic contamination was large, the anions released from the insoluble salts (in water) changed the nature as well as the concentration of the geopolymeric solution and the setting processes were retarded. Oxides, in general, behaved very differently from other salts, indicating the uniqueness of the oxygen anions in a system rich in hydroxyl and silicate anions. The inorganic salt contamination in geopolymers did not show any significant signs of structural change according to the XRD diffractograms collected. The seven-day compressive strength was not lowered by the inorganic salt contamination and it could sometimes be beneficial to the product performance, for example, an increase of 20 MPa was induced by the addition of calcium oxide. Inorganic salts as chemical additives have demonstrated the potential to modify setting times of geopolymers without sacrificing much of the productsÆ strength and integrity.

Jan 1, 2000

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB) Shovel/trucks, front-end loaders/ trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRE truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation) result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By Rob D. Morrision, Paul W. Cleary

"The best accepted method for design of autogenous and semi-autogenous mills is to carry out pilot scale test work using a 1.8 m diameter by 0.6 m long pilot scale test mill. The load in such a mill typically contains 250,000-450,000 particles larger than 6 mm, allowing correct representation of more than 90% of the charge. This scale of DEM model is now within the practical range of standard workstations running an efficient DEM code.This paper describes various ways of extracting collision data from the DEM model and translating it into breakage and wear estimates. Account is taken of the different breakage mechanisms (impact and abrasion) and of the specific impact histories of the particles in order to assess the breakage rates for various size fractions in the mills. These impact histories have the potential to be directly related to breakage as they most resemble the single particle breakage tests which are used by the JKMRC to calibrate more traditional population balance models for variations in ore behaviour. However, the specific impact histories also show a background of many low energy collision events within the mill. This Background may constitute what is usually regarded as “abrasion” breakage. As might be expected, high impact events are concentrated in the toe of the charge and near to the mill shell where the forces associated with the load bearing on each particle is more concentrated."

Jan 1, 2003

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

By M. Kerr, Petra Lampinen, Jinming Zhang, Petra Brodin, C. Hull, Nils-Johan Bolin, R. Asmatulu

"According to Darcy’s equation, the rate of dewatering varies as inverse square of the surface area of the particles to be dewatered and is proportional to the pressure drop across a filter cake. Thus, the difficulty in dewatering fine mineral concentrates can be overcome by using high-pressure filters. When treating ultrafine particles, however, it is often necessary to further dewater the filter cake using a thermal dryer. In the present work, novel dewatering aids that can reduce the pressure requirement have been developed. The reagents are designed to reduce surface tension, increase particle hydrophobicity and increase capillary radius, all at the same time. They were tested for dewatering mineral and coal concentrates in both laboratory and pilot-scale tests. The results show that the use of the novel dewatering aids can substantially reduce cake moistures and, at the same time, increase throughput. In this communication, the case history of using the reagents commercially at the Garpenberg concentrator is given. The use of the novel dewatering aids allowed the operators to use a vacuum filter to obtain desired cake moistures and obviate the need to use a thermal dryer.INTRODUCTIONDewatering is an integral part of mineral and coal processing operations, as it is necessary to remove water from concentrates (or clean coal) to minimize shipping costs, meet contract specifications, and recycle the process water. In general, the cost of dewatering increases with decreasing particle size, which can be attributed to the difficulty in removing the water trapped in the pores (or capillaries) formed between the particles constituting a filter cake.The various parameters affecting the process of dewatering, including the effect of particle size, can be understood in view of Darcy’s equation (Darcy, 1856):"

Jan 1, 2005

By I. O. Ojala

Detailed knowledge of velocity-depth trends is essential for constructing well-to seismic ties, determining background velocity and generating synthetic seismic traces for interpreting seismic amplitudes in terms of porosity, lithology and pore fluid type. The acoustic properties of shales are of particular importance in the exploration setting as shales constitute more than 80% of sediments and rocks in siliclastic environments. Seismic and sonic log data may be used for estimating overpressure in shales in order to maintain borehole stability during drilling. In addition, velocities in shales can be used for predicting its mechanical properties and hence, borehole collapse. Despite of the apparent importance of understanding shale acoustics, sonic logs in shales are frequently unavailable or unreliable especially for older wells. Hence, it is essential to compute pseudo-velocity logs from other available information. This can be accomplished by using empirical relationships or rock physics transforms. In this study we have compared the predictive power of resistivity (Faust 1951, Hubert 2008) and porosity based models (Wyllie 1956, Holt & Fjær 2003) for computing synthetic P-wave velocity logs using wireline log data from mudstone intervals at three North Sea wells. The wells 6507/2-1, 6507/2-2 and 6507/2-1 are located at the Haltenbanken area at the Norwegian Sea. The wells targeted hydrocarbon potential at the upper Cretaceous and lower Tertiary sandstone sequences. The sandstone beds are overlain by thick Tertiary and Cretaceous sequences of mudstones. Since our primary goal is to model acoustic velocities in shale, we used wireline data from the Nordland (NL), Rogaland (RL) and Hordaland (HL) groups that are mainly composed of mudstone. The mudstone beds were identified from the well log data by using natural gamma log, sonic and resistivity data as well as information from the Norwegian Petroleum Directorate website. The volume of shale was estimated from the natural gamma log and the data points with values higher than 0.65 were discarded. Similarly, the data points with shale volume less than 40 % were discarded. Furthermore, exceptionally high resistivity values amounting to more than 6 Ohm m were not included in the analysis. Porosities were determined from the density log assuming 2.7 and 1.05 g/cm3 for matrix and fluid densities, respectively. The depth that was used for calculating Vp from Faust (1953) was the depth below mudline in order to the compare of well data from wells that have been drilled at different depths (Hubert 2008).

May 1, 2009

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By Andreas Prucker

The Greater Vancouver Water District (GVWD) is currently constructing the largest water treatment plant in Canada. As part of this treatment scheme twin water transfer tunnels are being constructed. Work commenced with the 11 m diameter, 185 m deep Seymour Shaft which was excavated by drill and blast using a mobile crane for hoisting. The Seymour Shaft is the first large diameter shaft that has been sunk in Western Canada in recent years. The operational aspects associated with the hoisting, the drill-blast-support cycle and water control in the shaft are the focus of this paper.

Jan 1, 2008

By Elzbieta Mielczarski, Jerzy A. Mielczarski

"It is well documented that xanthate adsorption on sulphide minerals is electrochemically controlled process. Under well controlled potential conditions the adsorption of xanthate takes place at different potential on each mineral, hence, each mineral component can be selectively separated from ore. This was demonstrated in the past for single mineral systems. In real flotation this concept never works out for two reasons: the potential of single mineral particle results from its interaction with solution as well as from galvanic contact with other particles present in the flotation pulp. Thus, the potential of a single particle results from complex surface reactions controlled by solution chemistry and the presence of other mineral particles that also interact with the solution. In flotation it is not possible to control mineral particle potential as it was demonstrated in voltametric studies of single mineral.In this study adsorption of xanthate on pyrite, galena and chalcopyrite has been investigated in the presence of those minerals. The second mineral was in solution: (i) without any physical contact with the first one, (ii) in direct contact (non-liberated grain or connected by wire), (iii) in collision type contact similar to that observed in real flotation.The adsorption of amyl xanthate on pyrite, galena and chalcopyrite was monitored by infrared external reflection technique directly on mineral surfaces. Type of the adsorbed species and their amount were concluded from the recorded reflection spectra. The presence of second mineral in solution without any physical contact does not influence adsorption. The minerals behave as if they were separated (at least during 30 min of the experiment). However, any type of galvanic contact between grains of two different minerals has tremendous consequence on the adsorption of collector on the both minerals. The detected changes are dramatic, from no adsorption to a few monolayer coverage formation.For example, pyrite that adsorbs amyl xanthate strongly in single mineral system in its galvanic contact with galena practically shows no adsorption of the collector in the same solution conditions. On contrary adsorption of xanthate on galena is tremendously enhanced during the galvanic contact with pyrite. The observed changes in the surface reactions are discussed and mechanisms of xanthate interactions in different galvanic contact are proposed."

Jan 1, 2003