Search Documents

By W. Valderrama, D. G. Almond

Operation of large SAG mills requires a change in the conceptual approach to grinding processes. The traditional energy consumption criteria are now enhanced with new criteria derived from the mechanical dynamics of the mill load. This new approach demands instrumentation capable of providing accurate information about the load movement and the ratio of balls and ore inside the mill. This paper discusses two new performance enhancing tools available to meet these needs.

Jan 1, 2004

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton's JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton's empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d'évaluer JRC qui est un indice de rugosité superficielle d'une fracture de roche à l'aide du modèle de fracturation, compte tenu de son effet d'échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d'une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l'aide de la formule empirique Barton sur la base des résultats de l'essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d'évaluer l'échelle d'endentement d'une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d'évaluation de JRC par rapport au profil JRC.

Jan 1, 2003

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By E Hawkins, S Sheldon

Block caving is becoming a more widely adopted mining method allowing for underground massive low grade orebodies to be extracted economically. Underbreak during cave propagation is difficult to predict in terms of recovery and is not well-researched due to the small number of caving operations. During mining of E26 Lift 2 (E26L2) block cave at CMOC Northparkes Mines, a wedge of high grade material failed to cave, even with the assistance of preconditioning and subsequent attempts to induce caving. The ultimate solution for recovery of the uncaved wedge was the establishment of the E26 sublevel cave (SLC), which commenced mining in 2015, with production following in 2016. The SLC provides approximately 1Mtpa to supplement the lowering grade of the current E48 block cave feed. Applying the sublevel caving methodology to recover block cave underbreak has proven challenging. The impact of the caving stresses and preconditioning of the wedge have caused production limitations requiring continual remediation throughout production of the E26 SLC. The dependence on remediation work created a roadblock to implementing precharging as the prevalence of brow loss raised concerns over the inability to hook up the charged ring. In 2018, a wireless initiation trial was completed in the E26 SLC over 24 rings. The trial showed that precharging was achievable in this environment and greatly improved the safety of charge up personnel.

Mar 15, 2021

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels."

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

Jan 1, 1963

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By F. C. Wagner, E. P. Klier, D. E. Nulk

The presence or absence of plastic strain at a cleavarage surface is a question of much importance, and upon its answer depends future possible theoretical work. To investigate this question back-reflectinn X ray patterns were obained on the cleavage facets of ferrite grains. The test set-up consisting of FeK colli- mated radiation, single grain material and stationary cassette and specimen will not lead to a diffraction pattern, in general, but is an ideal arrangement for the exami-nation of surface effects. A pattern taken on hydrogen purified

Jan 1, 1949

By L. J. Lutz

The U.S. Bureau of Mines has developed an electrorefining process to recover Ni, Co, Cr, and other metals from mixed and contaminated superalloy scrap. The superalloy scrap is cleaned then directly electrodeposited as a Ni -Co deposit. The process recovers approximately 90 pct of the Ni-Co available from the scrap as a 99t pct pure Ni-Co alloy. During electrorefining the electrolyte undergoes a purification process which results in Cr and other refractory metals reporting to the purification residue. Operating data is given for a 3-L compartmented electrolytic cell. Techniques for the removal of Fe, Cr, and trace impurities from the recycled electrolyte are outlined. The economics of a facility producing 15 mt/d of a Ni-Co alloy are also discussed.

Jan 1, 1993

By Richard P. Graff

Author?s note: Diversity in practice exists in the application of Generally Accepted Accounting Principles (GAAP) for purchase price allocations with respect to the recognition of Value Beyond Proven and Probable Reserves or VBPP, as defined by the Emerging Issues Task Force (EITF) in EITF 04-3: ?Mining Assets: Impairment and Business Combinations?. This diversity appears to arise from differing interpretations of what constitutes sufficient information to value components of VBPP in business combinations. Concerned with this diversity in practice, respected members of the mining community formed a working group which prepared an issues paper that discussed this diversity and provided recommendations for recognition and valuation of VBPP in business combinations. The working group then submitted this paper to the EITF, requesting further guidance be issued on the concept of VBPP. In conjunction with the submission to the EITF, the working group also provided this paper to the United States Securities and Exchange Commission (SEC) for review and comment. The EITF discussed this issue at its May, 2008 agenda committee meeting. However, it declined to add this topic to the EITF agenda for further consideration. Absent additional guidance on VBPP from the EITF, the working group submitted a proposed definition of VBPP to the U.S. Securities and Exchange Commission for its consideration. The following article, which is consistent with the issues paper that was submitted to the EITF and the SEC, discusses the components of and valuation techniques for VBPP. The correspondence with the U.S. Securities and Exchange Commission, which includes the proposed definition of VBPP by the working group, is attached as Appendix 1 to this article.

Jan 1, 2008

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985