Search Documents

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiC1-KC1 mixtures, as first proposed by Gunkz.2 The details of the industrial process have not been made public hut Osborg8 stated that an efficiency of more than 90 pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on' German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of 140 kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, SiO2, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, Director, with respect to the iron and calcium Content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1949

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By Alan Dahlstrand

The Jamestown Mine is a 6.3-kt/d (7000-stpd) open-pit gold mining operation located in the central portion of California's historic Mother Lode district. Most early production from the Jamestown area occurred in underground operations from 1906 through 1916. Pit production began at Jamestown in early 1987 and continued until July 1994. Although additional mineral resources existed, they were deemed to be uneconomic. About 23.3 t (750,000 oz) of gold were produced from pit operations, compared to 31 t (100,000 oz) from early underground mining. Recent operations at Jamestown included two open pits, a flotation mill and a flotation tailings facility. Flotation concentrates were produced in Jamestown and shipped to Yerington, NV for cyanide leaching in a carbon-in-pulp (CIP) circuit.

Jan 1, 1995

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

Fully mechanized longwall mining with large mining heights (LMHs) in shallow-depth thick coal seams has been widely applied in Shenfu coalfield, China. Dynamic loading and rib spalling is serious when the LMH working face experiences periodic weighting in shallow coal seams. The advanced breaking position (fracturing ahead of the face) in the roof affects the strength of the mine pressure (weighting) when the roof is broken. Based on the theory of the “elastic foundation beam,” this paper presents a mechanical model for the advanced breaking of the roof, including a predictive formula. In an attempt to verify the formula, a field program consisting of multiple-point borehole extensometers installed in the roof in advance of the longwall face was performed in the No. 22201 working face of Zhangjiamao coal mine in the Shenfu mining area, China. The field measurement results show that the roof movement of the LMH working face is detected prior to roof pressure increase, and that the roof breaks approximately 5–8 m ahead of the face. This compares with a calculated value of 6.9 m, indicating that the formula developed in this research is reliable and should have application in predicting roof pressure associated with LMH working faces in shallow coal seams.

Jul 28, 2020

By Z X. Zhang

Ground vibrations from the blasts of the LKAB mine at the Malmberget town had reached 18-19 mm/s from year 2000 to 2002. From 2004 to 2010 the maximum vibrations had been reduced to 9 mm/s and most vibrations lowered to about 5 mm/s, indicating that the technical measures used in the mine are effective in vibration control. The major measure that has always been used in Malmberget mine is the method called Changing Initiation Sequence (CIS in short). Another method named Dividing Ring Blasting (DRB in short) is often applied to some special blast rings in the mine. Both methods have been proved to be successful in vibration reduction, and they do not need any additional costs. Because of the two methods, both maximum vibrations and average ones have been reduced by around 50% since 2004.

Jan 1, 2012

By H. Saridikmen, C. S. Kucukkaragoz

In the present study, the measurement of sulphur distribution ratios between the slag and metal phases encountered in the ferromanganese smelting has been carried out at 0.83 atm of partial pressure of CO at 1773 K by using classical gas-slag-metal equilibrium quenching technique as a function of composition. The distribution results were employed in calculating the sulphide capacities of SiO2-Al2O3-CaO-MgO-MnO slags in equilibrium with the Mn-Fe-Si-Csatd.-S metal phase. It is shown that the sulphur transfer from metal to slag phase increases with increasing the basicity of the slag. As expected, the sulphur distribution ratio decreases by increasing the silica content of the slag system. The effect of metal composition on the sulphide capacities of the slag as well as on the sulphur distribution ratios between the slag and metal phases have been discussed. Emprical relationships were developed to express the sulphur distribution ratios and sulphide capacities of the above slag system.

Jan 1, 2007

By G. F. Friel, J. C. Edwards

A series of seven underground-coal-mine fire experiments was conducted in the Safety Re-search Coal Mine at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. Coal and styrene-butadiene-rubber conveyor belting were burned upwind of two sensor stations, 18 m and 148 m from the fire source. Exhaust from a diesel locomotive flowed over the fire sources in six of the tests. Metal-oxide-semiconductor (MOS), CO, and optical-path-smoke sensors were positioned at both stations and found to be an optimum set of sensors for the fire discriminations. A representative set of 7,679 samples of CO data and data from the smoke and diesel-exhaust MOS sensors were used as inputs to train a neural network (NN). By testing 42,538 data samples from the seven experiments, all fires were detected by the NN within 9.67 min from the onset of significant changes in the MOS voltages without any false alarms.

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By R. J. Fantel

The Bureau of Mines investigated the resource availability of titanium minerals from 63 mines and deposits in 12 market economy countries. These mines and deposits contain, at the demonstrated resource level, an estimated 438 million metric tons (mt) of titanium dioxide (TiO2) in the minerals rutile, ilmenite, leucoxene, and anatase. An additional 314 million mt of TiOz is available from inferred resources. If all titanium minerals and other recovered heavy minerals are sold at total costs at least equal to the January 1984 market prices, approximately 200 million mt of contained TiO2 could be recovered in total. In terms of mineral concentrates, this equals approximately 11 million mt of rutile concentrate, 187 million mt of ilmenite concentrate, 3 million mt of leucoxene concentrate, 13 million mt of synthetic rutile concentrate (in addition to the ilmenite), and 89 million mt of titanium slag. The study indicates that world resources of low-cost rutile are declining. In order to maintain future supply for high-grade titanium resources, alternate sources will need to be developed, which may include higher cost rutile mines, Brazilian anatase deposits, increased production from slag operations, or more synthetic rutile capacity from ilmenite resources, which are abundant.

Jan 1, 1986

By D P. Yang, Yang R. G

The laws of throwing and heaping of engineering blast are important for making use of throwing and heaping of thrown body to form certain shape, such as building dams by directional blast. The article is to apply Ballistic theory of single thrown body to take the throwing course of thrown body as the movement of particle system, and then delimit the total of thrown body into units of thrown bodies, and regard the heaping shape of single thrown body as a perfect triangle, and found a quantitative relation between macro-geometry parameters of perfect triangle and designed parameters of explosives. The theory has been adopted in blast practice and gotten good effects.

Jan 1, 1999

By K. Wyper

"Gulf Minerals (Canada) Limited' s Rabbit Lake Uranium Operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and 134 miles northwest of Lynn Lake Manitoba.This paper describes flow sheet changes to solve operating problems and briefly describes future changes to accommodate the new ""B"" Zone ore.The Rabbit Lake mill was designed to process 1600 dry tons per day of uranium ore, with an average grade of 0.370 percent u3o8. In 1981, the mill processed 2040 tons per day at a grade of 0.231 percent u3o8 . The process modifications and flow sheet changes that allowed this increase in tonnage will be discussed in relative chronological order. Mill feed was introduced on June 10, 1975, the original equipment consisted of an Ingersoll Rand hydraulic breaker mounted over a 24"" square grizzly. The - 24"" ore was fed to a 2011 X 6"" seflli autogenous grate discharge mill close circuited with 20"" cyclones, the mill discharge was screened on a tyler double deck screen with the undersize (8 rnesh) reporting to the cyclones, the screen oversize was returned by conveyor belt to the mill feed chute.The cyclone overflow (28 mesh) was thickened in a 100' diameter thickener to obtain 55 percent solids for the leach circuit.The leach circuit consisted of two slurry holding tanks and five leach tanks."

Jan 1, 1982

By W. G. Sandell, L. C. Bauerle, K. C. Dean

"INTRODUCTION As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agncies engaged in purchasing and stock-piling some of the more critical and strategic materials. At the request of Dr. Alan M. Bateman, special representative of the Metals Reserve Company, metallurgical studies were made on three samples of oxide tin ore from, the States of Zacatecas and Guanajuato, Mexico. The samples were submitted for testing by A. Porraz of the Financiera Miners, S. A., institution Financiera, Edificio Guardiola, Despachos 500-507, Mexico, D. F.The samples as received were marked Nos. 1, 2, and 3 and described as follows:Sample 1. - Origin: Mining camp ""El Naranjo,"" municipality of Sombrerete, State of Zacatecas, Mexico. This sample was partly concentrated by washing and as received was all minus 10-mesh in size.Sample 2. - Origin: Deposits in Sierra. Fria and Juan Cherey, municipality, of Jerez,State of Zacatecas, Mexico. This sample represented run of-mine ore.Sample 3. - Origin: Mine ""La Frontere, "" Ranch of San Pedro del loya, State of Guanajuato, Mexico. This run-of-mine sample was low in tin content but came from a highly mineralized tin field."

Jun 1, 1947

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

"Separation in Froth (SIF) is a process for the separation of mineral particles during their descent downwards through a moving froth layer, generated on the surface of water or some other liquid media by means of a bubble generator and frother. Due to the special operation principles of SIF it is possible to separate mineral particles that are about 10 times coarser than the optimal particle size for conventional flotation. In this paper the performance of the SIF technique is presented in the separation of apatite, calcite and silicate minerals from various industrial sources, based on tests with laboratory and pilot plant-scale SIF machines. Basic laboratory test results of the flotation of pure diamonds are also presented.It was shown that calcite, apatite and diamonds with particle size up to about 3 mm can be successfully floated with SIF at high recovery and grade, provided that the degree of liberation is sufficiently high. Coarse calcite (+0.25-2.8 mm) was concentrated with reverse SIF in one flotation step at 87% recovery with better than 99% grade. Apatite particles coarser than 0.2 mm are not well floated in the conventional flotation circuit leading to high P2O5 content in the coarse size fractions of flotation tailings. On the contrary, SIF is capable of recovering such coarse particles at high recovery. However, P2O5 content of the SIF tailings starts to increase at about 0.7 mm due to insufficient liberation of apatite. At higher particle size the lack of hydrophobicity of apatite particles is also likely to lower the recovery.The pilot plant testwork showed that SIF can be successfully used at operating plants not only for preliminary upgrading of the feed of conventional flotation, but also for producing final grade calcite concentrate (>99.5%) from the screen overflow or from the cyclone underflow in a particle size range up to 1 mm. It was particularly promising that the separation took place in one SIF flotation step, instead of several stages of the conventional flotation circuit, with over 90% calcite recovery. The specific capacity determined with the 1 m2 pilot plant unit was approximately 30 t/m2h. Simultaneously the consumption of chemicals was significantly lower than for conventional flotation."

Jan 1, 2003

By K. Awuah-Offei

An aggregate plant may have difficulty balancing product stockpile inventories if hot mix asphalt (HMA) design engineers do not account for aggregate inventory during mix design. Yet HMA design engineers do not, often, take this into consideration during asphalt mix design. This is due to the lack of tools that enable the lab technician or engineer to optimize the mix for good performance while helping the aggregate plant manage its stockpile inventory levels and reducing the aggregate cost. This work presents a linear programming model of the asphalt mix design problem that helps aggregate plants manage their inventory levels while meeting HMA customer demands. The algorithm is implemented in MATLAB as an Asphalt Mix Design Optimization (AMIDO) program. The program is successfully validated with real-life data. The results show that AMIDO can be used to successfully produce any mix design while reducing the cost of aggregates by using the cheapest stockpile materials. The application of AMIDO will increase aggregate plant profitability when serving HMA customers and could potentially be modified for concrete aggregate customers too.

Jan 1, 2009