Search Documents

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By Robert Schnab

ASFINAG is responsible for the construction and operation of the Austrian highway system. It is approx. 2,400 km of highways and 65 tunnels with a total length of 200 km including the Tauern Tunnel. In order to improve the documentation of the tunnel construction, ASFINAG chose to use a state of the art tunnel scanning system to record the various stages of construction: excavation, initial shotcrete lining, smoothing layer and final cast in place concrete lining. The geometric and photogrammetric documentation is provided on a daily basis to all par-ties involved. This innovative concept provides accurate & complete information in real time. The tunnel scanner documentation of the 2nd tube at the 6.4 km long Tauern Tunnel will be presented in this paper as a part of the survey contract.

By V. Lakshmanan, Dan Mackie, J. Melnbardis

"Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market, with plans to begin production of a 500 TPD operation in 1984.Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogeneous grinding. In addition to producing marketable coarse graphite by such autogeneous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies. INTROOUCTIONWhen the Black Oonald mine at Calabogie Ontario ceased production in 1954 nearly all North American crystalline flake graphite had to be imported from offshore. Orebodies in the United States were too small or too low in grade to be exploited economically.The Houthillier Township near Mont Laurier in Quebec (Figure 1) was a known graphite-bearing area The Orrwell property in that area was delineated in 1957 Some test work including minor footage of diamond drilling was carried out by Italia Copper and the MHM Syndicate prior to 1981 when Orrwell acquired the property"

Jan 1, 1984

Study on Iron Ore Sintering with High Proportion of Specularite Concentrates Specularite iron ores have poor hydrophilicity and ballability as well as bad high-temperature reactivity, which restricts the large-scale application in the sinter and pellet production. In order to make the best use of the specularite concentrates, a novel process of Composite Agglomeration Process (CAP) is applied in this research. By the CAP, the percentage of specularite concentrates in the sinter mixture is increased to no less than 40 per cent as well as the coke breeze dosage is reduced by 0.3 per cent~0.6 per cent. Moreover, all the sintering indexes are obviously improved compared with the traditional sintering process. Researches on the metallurgical performances shows the finished composite agglomerates are high-quality burdens for blast furnaces. This investigation can provide an effective route to utilize the inferior specularite concentrates in the sintering.

Sep 13, 2010

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By M. Görnerup, A. Kapilashrami, Seetharaman. S., A. K. Lahiri

Simultaneous reduction and foaming of chromium-rich slag have been studied in a laboratory furnace equipped with X-ray image analysis. Reduction of the metal oxides by graphite generated CO, which caused the melt to foam. The slag composition continuously changed due to reactions and dissolution of lining. Gas generation rate, foam height, and gas bubble size were studied and correlated to slag composition. Viscosity increased significantly during the experiments due to a change in slag composition. Bubble sizes varied little during the progress of reactions but differed considerably for different slags. Bubble sizes were largest for V2O5 containing slag, which is contrary to the general understanding that the presence of strong surface active agents reduces the bubble size. The foaming index did not follow expected trends for bubble size and viscosity, suggesting that foaming index is not a suitable parameter for discussion of foams under dynamic conditions. Keywords: slag, foaming, dynamic conditions

Jan 1, 2004

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By T. S. Heah, S. T. Bishop

"The Lorraine property is located in the northern Intermontane Belt, north-central British Columbia. The property is underlain by intrusive rocks of the Duckling Creek Syenite Complex, an Early Jurassic, alkaline phase of the Late Triassic-Early Cretaceous Hogem Batholith. Two significant zones of copper-gold mineralization have been explored to date; the Main zone (historical Upper and Lower deposits) and the recently discovered Extension zone. A combined geological resource was estimated in 1975 for the Main zone deposits at 10 million tonnes averaging 0.7% Cu, and from 0.1 g/t Au to 0.34 g/t Au. The Extension zone, still at an exploration stage, is estimated to be considerably smaller than the Main zone.Copper-gold mineralization at Lorraine Mountain exhibits characteristics suggestive of both magmatic and hydrothermal origins, and may be related to orthomagmatic-hydrothermal fluid flow contemporaneous with magmatism and development of migmatitic fabrics. A depth greater than the depth of formation of classical porphyries may explain many of the variations displayed by mineralization at Lorraine. These characteristics distinguish Lorraine from other members of the alkalic suite of porphyry Cu-Au deposits in the Canadian Cordillera.IntroductionThe Lorraine prospect is located in the Omineca Mountains, at the headwaters of Duckling Creek, 56 km northwest of Germansen Landing (Fig. 1). The property is centred at latitude 55°55'N, longitude l25°26'W on NTS mapsheet 93N/14W. The area is typified by mountains of moderate relief, with elevations ranging from 1150 m in the valleys to peaks of 2000 m. Valleys are U-shaped and blanketed by glacial till which give way to steep, talus covered slopes and sharp ridges. Outcrop is generally limited to elevations above 1600 m (Fig. 2)."

Jan 1, 1995

By S. Read, G. Cook

The Hoek-Brown failure criterion is often applied to a wider range of rocks than the isotropic rock masses to which it is strictly applicable. This paper evaluates the patterns of defects in rock masses using spherical projection contour plots of samples of randomly-generated orientations and datasets from mapping of New Zealand closely-jointed greywacke rock masses. Two indices from the contour plots - the area within the 1% contour (A1%) and maximum concentration (Cmax) are introduced for distinguishing uniform (isotropic), random or regular defect patterns. The indices provide a potential extension to current guidelines on the use of the Hoek-Brown failure criterion. The paper also outlines kinematic checks to assess the influence of defect clusters on rock mass strength. Das Hoek-Brown Bruchkriterium, das strikte nur fuer isotrope Gefuege gilt, findet oft einen viel weiteren Anwendungsbereich. Diese Arbeit bewertet diverse Dispersionsmuster der Defekte einer Gesteinsmasse. Wir vergleichen in sphaerischer Projektion (1) Beispiele zufaelliger Orientierung von Defekten und (2) Felddaten ueber neuseelaendisache engstaendig geklueftete Grauwacken. Die Projektionen werden durch die Indices A1% (Flaechenanteil des 1%-Bereichs) and Cmax (Hoechstkonzentration) gekennzeichnet, welche isotrope, zufaellige und regulaere Muster unterscheiden und die aktuellen Richtlinien zum Hoek-Brown Kriterium ergaenzen. Wir testen ferner Defektgruppen der Gesteine kinematisch auf ihren Einfluss auf Massenfestigkeit. Le critère de rupture de Hoek-Brown est souvent utilisé sur une variété de roches plus étendue que les masses rocheuses auxquelles il est strictement applicable. Ce travail évalue la distribution des défauts au sein d&apos;une masse rocheuse en utilisant une projection sphérique des contours d&apos;échantillons d&apos;orientations générées aléatoirement et de données de cartographie provenant de greywackes à joints rapprochés de Nouvelle Zélande. Deux indices de cette projection - la zone des contours en dessous de 1 % (A1%) et celle de concentration maximum (Cmax) sont introduites pour distinguer les répartitions uniformes (isotropes), aléatoires ou régulières. Ces indices fournissent une extension potentielle aux règles d&apos;utilisation du critère de rupture de Hoek-Brown. Ce travail utilisent également les contrôles cinématiques pour évaluer l&apos;influence des groupes de défauts sur la résistance de la masse rocheuse.

Jan 1, 2003

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, Graduate Colorado School of Mines. Four years&apos; experience in West and Northwest. Two years with American Smelting and Refining Co. Wishes to join field party on geological work, mining or areal, where opportunity will be given to be of direct assistance to chief of party in solution of field problems. Age, 26. Unmarried. At liberty June 1. No. 342. Member, technical graduate, aged 30, with&apos; 7 years&apos; experience in concentrating and mining, desires a position of authority with reliable company. At present employed. No. 343. Member. Ambitious, energetic, tactful engineer, college graduate, married, aged 30, desires location with a large coal mining organization. Seven years with present employers -n middle west; has had broad experience in the past eight years on examination, development and construction; successful record in handling men. Position must carry responsible work and a future. Will go anywhere for proper opportunity. Exceptional references as to reliability, character and capacity for work. No. 344.

Jan 3, 1917

By Douglas Anderson

Even though there is always a feeling of anticipation before a blast is detonated, most blasts are part of a day’s work. Once in a while there is an event that impresses even the most jaded blaster. Few blasts have had the impact of the Kingdome implosion in March of this year. Fortunately for both the Seattle area and the explosives community, the “impact” of the implosion was far less than many local residents had feared. This outcome, of course, was not by chance, but the result of careful planning and design. An urban implosion requires a mix of engineering, logistics, and public relations. Unique challenges on this project tested the resourcefulness of the entire team.

Jan 1, 2001

By L. Alan Weakly

Global warming is a political reality in the United States today. The actual impact of the continued utilization of fossil fuels is not known and is open to debate. However, the growing concern about the continued use of these fuels is problematic. There are technologies available to us today that would permit America to meet its future energy demand and not contribute to global warming. The inconvenient reality is that fossil fuels cannot completely be replaced with energy conservation and the use of wind, solar, hydroelectric, geothermal and nuclear energy. The connection between the greenhouse effect and global climate change was first identified by physicist John Tyndall in the 1860s. To prove the greenhouse hypothesis, Roger Revelle and his research team started measuring carbon dioxide concentrations in the earth?s atmosphere in the early 1960s (Becker, 2007). With the rising concern about global warming, scientists throughout the world have been obtaining surface and air temperature data. Scientists have also been comparing CO2 concentrations found in glaciers throughout the world with theorized annual temperatures. Data for both dates back 1,000 years. Armed with this data, many nations of the world and the United Nations Intergovernmental Panel on Climate Change (IPCC) have concluded that climate change is a reality. The IPCC also concluded that this climate change is the result of mankind?s consumption of fossil fuels and that catastrophic consequences will occur on a

Jan 1, 2008

By A. Kondratiev

A structurally-based viscosity model for fully liquid silicate slags has been developed and applied to the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation. The model links the slag viscosity to the internal structure of melts through second nearest neighbour bonds concentrations taken from the quasi-chemical thermodynamic model. This viscosity model describes experimental data over the whole temperature and composition ranges within the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation and can now be applied to other industrial slag systems.

Jan 1, 2004

By Shane McDonald

Australia produces approximately 84 million tonnes of coal per annum from 30 longwalls in New South Wales and Queensland, operating at an average depth of around 300m. Industry trends and expectations place increasing emphasis on the reliability of these operations; for example, the current average face width is 245m and this is expected to increase to approximately 270m by 2010. In recent years, Beltana No.1 Mine has consistently been Australia?s highest longwall producer, with ROM output of 7.2Mt in YEJ2007. Strata management has become a key feature of the operation of Australia?s longwall mines, as a tool to manage variances in the geotechnical environment. This involves an understanding of the impacts of the geotechnical environment on ground behaviour and the implications for mine design, stability and associated support, interaction and horizon selection. The anticipated ground control impacts of these factors form the assumptions that drive the format of plans specifying both triggers and actions, with quantified, monitoring-focussed experience used to refine the plan in a continuous improvement (ie ?plan-do-check-act?) process. This paper summarises the Beltana No.1 Mine strata management methodology and experience to-date.

Jan 1, 2008

By B. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformations. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, time-lapse point clouds of mine workings. In order to determine sloughage volumes and locations, a total of 11 laser scans were performed 41 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds.

Feb 27, 2013

By H. Warlimont

In recent investigations of the microstructure and crystallographic features of martensite by electgon microscopy,&apos;, &apos;9 thin films (about 50 to l000A in thickness) have been used as specimens. It was found by W. Pitschl ,2 that the lattice relationships between the supefiaturated fcc matrix and the martensite formed in thin films were different from those observed after transformation in bulk material. Corresponding differences are to be expected in nucleation and in reaction kinetics in the formation of martensite in thin films, but have not yet been reported. In the course of the preparation of thin films of iron-base alloys for investigation by electron microscopy it was observed that films of alloys, whose martensite formation temperature (Ms) was below room temperature, formed martensite during the electrochemical thinning process conducted at or above room temperature. The chemical compositions and approximate bulkM,-temperatures of the three materials on which this observation was made are listed in Table I. The alloys were vacuum-melted from high-purity metals. It can be seen that the effect occurred in alloys that contain only sub-stitutional components as well as in alloys that contain carbon as an interstitial solute. The appearance of martensite formed in this manner is illustrated in Fig. 1, which represents a polished film of alloy No. 1 at XI0 magnification. The martensite plates can be recognized by their surface relief effects. In addition, heavily strained (owrinkledo) austenite can be seen near the edges of the film where it is thinnest and transformation stresses or strains can be accommodated by plastic deformation most easily. The nonuniform distribution of transformed regions is probably due to the varying thickness of the film. These observations were common to all materials listed in Table I. Because effects of supercooling or straining can

Jan 1, 1962

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and 1580ºC under 0.03 atm, 0.05atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged to SiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S)systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermodynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on pseudo ternary SiO2–(AI2O3+CaO+MgO)–(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: Chromium, slag, equilibrium

Jan 1, 2004