Search Documents

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and an extensive literature has resulted. Usually each individual paper has placed emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed 'emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By T. Hart

Nuclear gauging is used world-wide in almost every industry. From mining and ore-grading to finished product, the metallurgical industry is one of the biggest users of nuclear sensors for inventory, process control, and quality assurance. This paper will discuss the basic theory of gamma transmission gauging techniques found useful in mining, milling and metal production. Techniques to be discussed are gamma transmission for level and density. A major new technique will also be discussed. This technique is called gamma backscatter. The uniqueness of this technology, how to apply and the differences between transmission and backscatter will be accentuated.

Jan 1, 2011

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By G R. Ballantyne, M S. Powell

A comprehensive Australia-wide survey of comminution energy consumption at copper and gold mines was presented by the authors at the 11th AusIMM Mill Operators’ Conference 2012. The database has been extended to include major overseas mines and used to benchmark comminution energy consumption across the industry. The mines included in this study now represent 15 and 24 per cent of the total global gold and copper production respectively, and almost all Australian production. The comminution energy intensity per unit of saleable metal has been presented in a graphical form similar to a cost curve used in economics. The graphical method has been developed to assess the competitive advantage that can be achieved by reducing comminution energy intensity.This benchmarking tool has been applied to three published case studies to assess its applicability. The first case study indicated that a large reduction in size-specific energy (kWh/t -75 µm) was achievable by converting standard semi-autogenous and ball mill circuits to include high pressure grinding roll and stirred mills. The second case study investigated the metal-specific energy reduction historically achieved by Bougainville with the addition of a preconcentration screening plant. The final case study was conducted by Barrick Gold Corporation and involved incremental efficiency upgrades at three of its gold mines: Cortez, Cowal and Mara North. The application of the benchmarking tool to each of these case studies successfully demonstrated the scale and competitive advantage that was achieved by reducing energy intensity.CITATION:Ballantyne, G R and Powell, M S, 2014. Benchmarking comminution energy consumption for improved efficiency, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By John E. Trombly

System objectives and design criteria for an in-mine visual personnel paging system are discussed. Display technologies are evaluated and tradeoffs leading to display selection are described. The prototype dispatcher's console, battery/receiver box and visual display assemblies are functionally described. The report includes circuit descriptions, schematics, parts lists and equipment cabinet drawings for the three assemblies. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 1975

By Samuel J. Sims

The Grace mine magnetite deposit, located 2 miles north of Morgantown in Berks County, Pennsylvania, was discovered in 1948 by an aerial magnetometer survey. It is situated on the southern border of the Triassic lowlands section of the Piedmont province. Cambrian sandstones, shales, and limestones overlie Precambrian crystalline rock and were folded and thrust-faulted during the late Paleozoic Appalachian revolution. Late Triassic continental sediments were deposited on the deformed basement rocks and were intruded by Late Triassic diabase dikes and sills before regional tilting and normal faulting occurred. The Grace mine magnetite ore is characteristic of the Cornwall type. The ore has replaced a Cambrian limestone lens isolated between Triassic diabase footwall and Triassic sedimentary rock hanging wall. The ore body is roughly tabular in shape, dips 20° to 30°NE and plunges about 20°N80°E. The ore is granular, fine- to medium-grained, typically consisting of unevenly distributed magnetite in a matrix of light green to white serpentine gangue. Magnetite is the major ore mineral, pyrite and chalcopyrite are common accessory minerals, and pyrrhotite occurs locally. Sphalerite, marcasite, galena, hematite, digenite, and goethite are uncommon. Serpentine, talc, and chlorite are the major gangue minerals; calcite and dolomite are common, and phlogopite, tremolite, and biotite are present locally. Apatite is a common accessory; sphene is rare. Calcium-magnesium silicates were formed first by contact metamorphism of impure limestone by the intruding diabase. Later, the silicates were altered hydrothermally to the serpentine- talc-chlorite assemblage now present. Magnetite, the first ore mineral, formed by replacing serpentine and was followed by pyritepyrrhotite and then by chalcopyrite-galenasphalerite. Marcasite, secondary pyrite, goethite, and hematite are secondary minerals resulting from alteration of pyrrhotite and magnetite. It is estimated that confining pressure was about 1500 bars and the temperature range was 500° to 675°C during ore formation.

Jan 1, 1968

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By Merle L. Bowser

The Bureau of Mines has developed a portable recording methanometer that utilizes the Bureau's methane sensor. The methanometer can operate continuously for at least 30 hours on small, sealed, rechargeable lead-acid batteries.

Jan 1, 1969

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1955

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951