Search Documents

By Doug Tesarik

Researchers from the National Institute for Occupational Safety and Health1 (NIOSH), together with employees from The Doe Run Company, are monitoring and evaluating the stability of a pillar retreat section at the Fletcher Mine, a lead/zinc, room-and-pillar mine near Bunker, MO. Cemented rockfill is being used to provide roof support as high-grade, remnant ore pillars are mined. Earth pressure cells and deformation meters placed in backfill panel pillars monitor stress change and vertical deformation, respectively, as nearby ore-bearing pillars are extracted. Similarly, biaxial stressmeters and borehole extensometers are used to monitor mining-induced stress change and deformation, respectively, in long-term support pillars. Data from these instruments indicate that when ore-bearing pillars were mined, stress was redistributed from support pillars to a backfill panel pillar. The data also indicate that the backfill and support pillars have remained stable for two years after pillar extraction was completed in the area. This research demonstrates the importance of using reliable instruments to document the geomechanical behavior of pillars and backfill. Gaining a better understanding of roof support and stress redistribution mechanisms is a fundamental part of NIOSH's goal to reduce and/or predict rockfalls, which are still among the leading causes of injuries in metal/nonmetal underground mines.

Jan 1, 2006

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By John Dasher

In 1980, some US cars were designed and built to metric dimensions; wine and gas were sold by the liter; and the March of Dimes Walkathon was measured in kilometers. Although the US Congress has taken a ''soft" approach to metrication, and public resistance to the idea remains strong, the use of metric units is becoming more and more widespread. As the minerals industry becomes more international in scope, US mining companies are converting to the metric system-particularly those companies with business interests overseas.

Jan 2, 1981

By G. B. Bell

"INTRODUCTION On February 1, 1962, after five years of exploration and research, Jones & Laughlin Steel Corporation announced that they would develop the Adams Mine. Plant construction began immediately and in December of 1964 the first shipment of pellets arrived at J & L's blast furnaces in Pittsburgh. J & L continued to operate the property through its wholly owned subsidiary, Jones & Laughlin Mining Company, Ltd., until August of 1971 when it was sold to Dominion Foundries and Steel, Limited of Hamilton. Dofasco engaged Cliffs of Canada, a subsidiary of Cleveland Cliffs Iron Company, to manage the operation of the property.SUMMARY:The Adams Mine is a one million tons per year iron ore pellet operation located in the Boston Township Iron Range, approximately seven miles southeast of Kirkland Lake, Ontario. The property includes 5,300 acres in which eight areas suitable for open pit mining have been outlined. It was estimated that the reserves in these out lined areas are sufficient to produce 30 million tons of high grade iron ore pellets.The ore 'consists of fine grained magnetite with alternating layers of chert and is mined by conventional open pit methods. This extremely hard and abrasive ore averages about 20 percent magnetic iron, and has a ratio of concentration of 3. 9 /1. Presently, mining operations are confined to two pits with a third one being developed for operations to begin in 1973.The run-of-mine ore is crushed and ground and then concentrated by magnetic separation and flotation to a concentrate grade of 68 percent magnetic iron. The concentrate is agglomerated by a grate-kiln pelletizing process and shipped by rail to Dofasco's blast furnaces in Hamilton and to Jones & Laughlin's furnaces in Pittsburgh."

Jan 1, 1973

James Barnes is Managing Director of James Barnes & Associated Ltd which is a company that has invested ten years of development to provide developers with a transparent, user friendly consultation framework that identifies who needs to be consulted, how they are to be consulted and procedures required to manage the risks associated with getting all the wrong! Despite the assertion above, this paper is not about to provide delegates with the answer to whom they ought to consult or identify the expectations that Maori might have in regard to the consultation process. It would be a very brave person indeed who would venture an opinion on such a sensitive subject. There are no short cuts to finding out what expectations Maori might have on any given situation. Nothing can be taken for granted. What this paper will attempt to do however is provide practical insights into what might be on the minds of Maori interests as they deal with the issues associated with mineral resources, particularly those under Treaty of Waitangi Claim. The Treaty of Waitangi has a significant bearing on the current debate between Maori and the Crown regarding ownership of mineral resources in New Zealand. The Waitangi Tribunal is currently hearing a case presented by a number of Iwi over the ownership of oil and gas resources in Taranaki and Hawkes Bay. Others will follow. The Crown and Maori have never been able to settle differences over ownership rights without resorting to legal action and it looks like this scenario is about to be repeated in regards to minerals. The Crown has a duty to actively protect the Maori interest. This is a fundamental expectation in the relationship between Maori and the Crown. In the case of minerals, Maori have yet to see the Crown do its duty. The impact on developers has become evident through Maori objections to consent applications as the issues of mineral right remain unresolved.

Jan 1, 2000

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By J. Shang, P. Howarth, B. Morris

Tailings from the nickel refinery in Copper Cliff, Ontario, consist of fine silicates mixed with a variable amount of conductive and magnetic minerals mainly associated with sulphides and iron oxides. Subsequent oxidation of sulphide- rich phases within the tailings results in the formation of an acidic leachate that may contain significant concentrations of trace metals. Mapping the spatial distribution of regions of higher sulphide concentration therefore provides insight into the distribution of the acidgenerating potential within the tailings. Electrical conductivity is constrained by two parameters — the concentration of metallic sulphides and the ionic concentration of acid in groundwater. Magnetic susceptibility is directly related to the pyrrhotite and magnetite content. It is proposed that combining information derived from airborne electromagnetic and magnetic surveys can provide an indication of metallic sulphide distribution. Preliminary investigations of airborne electromagnetic and magnetic data acquired concurrently over the sulphide-rich Copper Cliff tailings site reveal that these parameters can provide information on mine tailing extent and permit separation of tailings with varying compositional and alteration levels. Airborne geophysical data provide information about the subsurface while a digital elevation model (DEM) and hyperspectral imagery record surface conditions. Integration of the two data sets can reduce ambiguity when interpreting mine tailing distributions and their subsequent alterations.

Jan 1, 2001

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By E Kasai, T Nakamura, E Shibata

In the present study, formation of PCDD/Fs from carbon particles like æsootÆ, so called de novo synthesis, was experimentally simulated using the powder mixture of graphite and metallic chloride. Composite states of graphite and chloride particles were varied by the preliminary treatment, ie high-energy ball milling for different time or heating at different temperatures. These samples were subjected to the measurement of the rates of weight loss mainly due to the oxidation of carbon, the formation of absorbent organic chlorides (AOX) and the formation of PCDD/Fs at 300¦C. The amount of PCDD/Fs formation increased by applying certain pretreatments. Further, linear relationships were obtained among the formation rates of PCDD/Fs and AOX and the weight loss of sample. These results will give useful information to investigate the mechanism of PCDD/Fs formation from unburned combustible carbon and hydrocarbon in thermal processes.

Jan 1, 2002

By D. Waite

The Chairman opened the session by wondering why so few papers on Maritime Structures had been received for this conference. Perhaps because the marine environment is so hostile and the access so difficult that engineers tend to be more prudent about new ideas and designs. Dennis Waite noted the number of grey hairs in the room - grey hairs which could be equated with experience gained the hard way. He hoped that this experience would be passed on in the discussion period of this session. The Chairman was delighted to welcome two authors from China, Mr Sun and Mr Liang. He was most grateful on behalf of the conference for their efforts both in preparing their papers and for being able to present them. He regretted that Messrs Noce and Fedolino were not able to present their paper and then welcomed Mr Christensen from Denmark who would present the first paper.

Jan 1, 1991

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By William M. Gleason

The war in Vietnam stretched into another decade, an American President was at the brink of impeachment, the earth was given its own day, twin tower monuments of American ingenuity were completed in New York and would stand high above the Manhattan skyline for 31 years. Inflation, oil shortages, low commodity prices and America’s 200th birthday were part of the decade — it was the 1970s. For the mining industry, the demands of the decade would be high and the challenges would be significant. Because of the many challenges that lined up in front of it, the mining industry was forced to work smarter and more efficiently. The industry also expanded its borders in search of new resources and struggled along with the rest of the world through a fuel crisis, inflation and a recession.

Jan 1, 2007

By V. J. Sikora, W. J. McGuire

Several years ago, we used an electric analogue computer to study the effect of vertical fractures on the productivity of wells in expanding fluid-drive reservoirs. The results of this work were used both as a guide to research and as a basis for the design of actual fracturing operations. In 1958, Dyes, Kemp and Caudle' published portions of the data from this study. The results were released in 1959 to service companies for use in fracturing guides. The purpose of this note is to discuss the experimental conditions and assumptions which were made to derive the information which is already partially a matter of public record. ASSUMPTIONS This study applies to fractures which extend in a vertical plane symmetrically from the well. For simplicity, we chose to study the case of a well in a square drainage area with its fractures extending toward two of its nearest neighbors. We have assumed no migration of fluid across the boundary of this area. The quadrant shown in Fig. 1 models this system. We made the usual assumptions that the reservoir is homogeneous and isotropic, that the fluid is homogeneous and that production is effected by fluid-expansion drive. We also assumed that the fracture extends from top to bottom of the reservoir. Of more practical interest is our assumption that the fracture does not change the size of the drainage area. This premise is appropriate if all the wells in the reservoir are fractured in the same way. But where a single well is fractured, its drainage area may be enlarged at the expense of its neighbors. This could be of economic importance. The assumption that the fracture will not extend beyond the established drainage area of the well also limits the application of the results. Such long frac- tures will yield benefits in excess of those predicted here. When we assume homogeneity, we disregard the frequently observed zone of damage in the vicinity of the well. Where damage is severe, the benefits resulting from by-passing it will far exceed those predicted by this study. All comparisons were made of systems producing in the semi-steady state. By this we mean that equal volumes contributed equally to flow (pressure was dropping at a uniform rate throughout the system) when the rate of flow was observed. EXPERIMENTAL SET-UP We used the pool unit of an electric analyzer' in this study. The squase drainage system of a well was rep-

By Edmund Newton

The Haile mine has been the outstanding gold-mining operation and the largest single producer of gold in the Appalachian region. Gold was discovered at the Haile in 1827, previous to the present operation, production has been nearly $4,500,000 (gold at $20.67 per ounce.) from somewhat over a million tons of ore, with an average extraction of about 70 percent. The Haile property, now operated by Haile Gold Mines, Inc., is in the southern part of Lancaster County, South Carolina, 3-1/2 miles northeast of the town of Kershaw and 55 miles north of Columbia, the State capital. (See fig. 1.) The corporation has a lease and purchase contract on 1,805 acres, covering the present productive area. In addition, it holds lease contracts on 1,500 acres additional adjacent to this area.

Jan 1, 1940

RICHARD D. PICK RMCI PRESIDENT 2000-2001 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 97th Regular Meeting and Convention to be held June 24 thru June 26, 2001 Steamboat Springs, Colorado

Jan 1, 2000

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By Axel Doelcken

?? Liebherr excavators in standard configuration are generally designed to operate in an ambient temperature range between -12°C and +55°C (10.4 °F and 131°F). ?? To operate effectively and efficiently in very low temperatures special consideration needs to be given to the design ??An inappropriately designed hydraulic system unable to withstand extreme changes in temperatures or varying working conditions will lead to: - premature wear and more frequent replacement of components - increased maintenance & unplanned downtime This will affect productivity & operating costs.

May 1, 2008

By James J. Tansey

A Deep Foundations Institute meeting with the University of Michigan at Ann Arbor in March of 1984 featured legal rights under Differing Site Conditions. A workshop conducted by the authors and Gerard Ittig, Esq. added to the value of the symposium. This paper will be of interest to your attorneys in any subsurface disputes.

Jan 1, 1985