Search Documents

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

Upgrading and Removing Phosphorus from Low-Grade and High Phosphorus Containing Iron Ores

Sep 13, 2010

The modern Golden Cross mine entered the production phase in January 1992. The project is designed to produce over 100 000 oz/yr of gold and over 300 000 oz/yr of silver during a mine life of eight years. An open pit and an underground mine are operated producing around 850 000 t/yr of ore, to feed a conventional carbon-in-leach processing plant. Golden Cross is owned in joint venture by Coeur Gold New Zealand Limited (80%) and Viking Mining Company Limited (20 %).   Since the start of production several major aspects of the design have altered. The underground mine began as a mechanised cut and fill operation. The cut and fill stoping progresses in 3.3 m flatback lifts with maximum stoping width of 6 m. Where the ore zone is wider than 6 m a post pillar cut and fill method is used. In 1993 a new bench mining plan was introduced between the 270 and 260 levels. Flatbacking continued in the footwall drives in anticipation of variability of the ore width and orientation. The development of levels below the main service 200 level has indicated a possibility of bulk mining the ore block rather than flatbacks. This could lower mining costs but also introduce higher dilution rates. Development is in the advanced stages for trialing this method.

Jan 1, 1994

By Dorothy M. Richardson

The Bureau of Mines has participated in the American Petroleum Institute Research Project 48A (API-RP48A) program on the Separation and Identification of Sulfur Compounds in Crude Petroleum. The lack of reference compounds or infrared spectral data has made difficult the identification of individual sulfur compounds boiling above 140° C. The recent acquisition of 24 alkylthiophnnes has made possible a limited study of this important class of sulfur compounds. The infrared spectra of 2-monoalkylthiophenes and 2,5-dialkylthiophenes for the 2 to 15p range are reported. Correlations for determining the 2-alkyl and 2,5-dialkyl substituted thiophenes are derived from this information. The 2-alkylthiophenes show a unique pattern in the 5.50 to 6.54 region, while the 2,5-dialkylthiophenes show a distinctive pattern in the 5.6µ to 6.7µ region. A skeletal vibration occurs in the 9.5 to 10.0µ region for all of the thiophenes investigated. These data will aid the infrared spectroscopist in the identification of compounds of the type reported.

Jan 1, 1961

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

By J L. Carpenter, S M. Iveson, K P. Galvin

Wet beneficiation of iron ore fines less than 1 mm typically involves a desliming stage ahead of the fine gravity separation such as spirals. The desliming is achieved using a bank of cyclones. The reject ultra-fines emerge in the overflow stream at relatively low pulp density, contain high proportions of low-value slimes, but also well-liberated iron ore ultra-fines below 0.045 mm in size; however, recovering the valuable iron ore ultra-fines from this overflow stream presents a significant challenge due to the need to remove such a large amount of water and slimes.The REFLUX™ Graviton consists of distinct 3D-printed modular units, based on REFLUX™ Classifiers, which are rotated at high speed in a large centrifuge. This system has previously been investigated under semi-batch conditions, demonstrating the potential for precision separations with significant capacity. It has been shown that the throughput advantage of the inclined channels and G forces multiply. This is the first paper presented showing the performance of this system under continuous steady-state conditions. Ultra-fine silica in the size range of 0 to 0.045 mm was fed to the Graviton at different volumetric rates, fluidisation rates and pulp densities ranging from 2 wt per cent to 30 wt per cent, in order to develop a fundamental understanding of the system’s performance. Experiments were then repeated using ultra-fine iron ore.CITATION:Carpenter, J L, Iveson, S M and Galvin, K P, 2017. Separation of ultra-fine particles using the REFLUX™ Graviton, in Proceedings Iron Ore 2017, pp 141–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Coal mining in New Zealand is principally a State-owned and controlled operation where the State produces 70 per cent of the coal in New Zealand and 65 per cent of coal mined in the Waikato. The State's flexibility in production quality and price makes them tough competition. Coal in the Waikato varies in quality considerably throughout the region making the high quality coal deposits as in the Huntly district a highly sought after commodity. The high quality of coal is often offset against transport costs as, for example, Maramarua coals can compete effectively in the Auckland market and dollar per calorific value basis.

Jan 1, 1984

By F. -Z. Ji, A. G. Irons, M. Barati, K. Coley

In order to optimize carbon injection into oxidizing slags, in terms of carbon and iron yield, we must have a detailed understanding of the kinetics of the reactions involved. The current study measures the rate of carbon oxidation during injection at steelmaking temperature by means of injections of coal into EAF slags. The compositions of analysed outgoing gas were used to calculate gas flow rate and hence the gasification rate of carbon. A fundamental equation to predict residual carbon in slags was developed. The predictions using this model at moderate injection rates are in good agreement with experimental data. The reaction rate of EAF slag with carbon is under mixed control by the slag gas and the gas carbon reactions. The relative importance of each step depends mainly on the v-ratio of slags. A relative reactivity parameter ? has been defined and it is found to be important to carbon-slag reaction kinetics and slag foaming. Key words: carbon-slag reaction, kinetics, slag foaming.

Jan 1, 2004

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

By Willem Le Roux

Occupational health and safety is regulated by statute and common law. South Africa has, like many other countries, legislated extensively on occupational health and safety. Despite the body of legislation, the common law continues to play an important role as far as it concerns contractual, delictual and criminal liability. Two major Acts regulate occupational health and safety viz. the Occupational Health and Safety Act, No. 85 of 1993 (?OHASA?) and the Mine Health and Safety Act, No. 29 of 1996 (?MHSA?). The MHSA applies to mines and works as defined and related aspects. OHASA applies to other industries but does not apply to employers and workplaces to which the MHSA and certain matters covered by the Merchant Shipping Act, No. 57 of 1951 apply. See section 1(3) of OHASA. 2 The employer?s health and safety obligations in terms of the MHSA 2.1 Section 2(1) of the MHSA provides amongst others, as follows: ?The employer of every mine that is being worked must: (a) ensure, as far as reasonably practicable, that the mine is designed, constructed and equipped: (i) to provide conditions for safe operation and a healthy working environment (ii) ... (b) ensure, as far as reasonably practicable, that the mine is commissioned, operated, maintained and decommissioned in such away that employees can perform their work without endangering the health and safety of themselves or of any other person?.

Jan 1, 2011

By S. Djaroudib

Keywords: iron recovery, hematite, hydrolysis, polyvinylpyridine The precipitation of hematite (Fe2O3) from ferric chloride media at ambient pressure and at temperatures below 100°C was studied as part of a program to recover a marketable iron product form metallurgical processing streams and effluents. Hematite was formed in preference to ferric oxyhydroxides (e.g. ß-FeO?OH) by controlling the precipitation conditions, especially by adding Fe2O3 seeds. The extent of the hydrolysis reaction was found to depend primarily on temperature and on the free-acid concentration. As to the latter, the controlled addition of an adsorbent of free acid, in our case the anionic resin polyvinylpyridine (PVP), was shown to allow for the nearly complete removal of iron as readily filterable Fe2O3. The hematite product typically contains = 63% Fe and = 1.5% Cl, and its composition does not change appreciably upon repeated cycling using regenerated PVP.

Jan 1, 2005

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By M. Coetzee

The susceptibility of experimental low-nickel Cr-Mn-N stainless steels to hot cracking, sensitization, and pitting corrosion in the as-welded condition was investigated. These steels were developed for deep-drawing applications and are similar in composition to type 201 stainless steel. In order to obtain good formability, the rapid rate of work-hardening (characteristic of the 200-series steels) was decreased by the addition of copper. The behaviour of two sets of alloys during fusion welding was investigated: 17Cr-7Mn-4Ni-o.5Cu steels containing 0.001 to 0.27 per cent nitrogen, and 17Cr-7Mn-2Ni-o.1N steels with copper contents varying between 0.01 and 3.11 per cent. Al the steels in these two sets initially solidify as d-ferrite, which transforms partially to austenite during cooling. As the nitrogen level increases, the microstructure of an autogenous-weld metal ranges from large amounts of d -ferrite, martensite, and Widmanstätten austenite, to austenitic structures with small amounts of vermicular d -ferrite. The formation of d -ferrite during solidification and the presence of ferrite retained in the weld metal indicate that the experimental alloys will not be susceptible to hot cracking during welding. Except for the alloy with 0.27 per cent nitrogen, the resistance to pitting corrosion of the experimental steels in the as-welded condition is inferior to that of type 304 stainless steel. None of the experimental steels is susceptible to intergranular attack in the as welded condition. The alloys with 0.19 and 0.27 per cent nitrogen have properties (corrosion and microstructure) similar to those of type 304 stainless steel in the as-welded condition.

Jan 1, 1996

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By D. L. Forrester

This paper, describing the milling practice of the Old Dominion Co., is one of a series being prepared by the: United Staten Bureau of Mines. ACKNOWLEDGMENT In the preparation f this paper, acknowledgment is made of the valuable service rendered by R. S. Allen, metallurgist of the Old Dominion Co. T. G. Chapman, one f the consulting engineers of the Bureau of Mines, assisted in arranging the paper for publication.

Jan 1, 1931

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009